The effect of incorporating common dodecyl anionic and cationic surfactants such as dodecyltrimethylammonium bromide (DTAB), dodecylethyldimethylammonium bromide (DDAB), and sodium dodecylsulfate (SDS) in nanocomposites of reduced graphene oxide and nanocellulose are described. The stabilization and electrical properties of the nanocomoposites of reduced graphene oxide (RGO) and nanofibrillated kenaf cellulose (NFC) were characterized using four-point probe electrical conductivity measurements. Raman spectroscopy, field emission scanning electron microscopy, and high-resolution transmission electron microscopy were used to investigate dispersion morphology and the quality of RGO inside the NFC matrices. Small-angle neutron scattering (SANS) was used to study the aggregation behavior of the aqueous surfactant systems and RGO dispersions. The cationic surfactant DTAB proved to be the best choice for stabilization of RGO in NFC, giving enhanced electrical conductivity five orders of magnitude higher than the neat NFC. The results highlight the effects of hydrophilic surfactant moieties on the structure, stability and properties of RGO/NFC composites.
In this work, nanocomposite ultrafiltration (UF) membranes were synthesized through addition of different quantities of amino-functionalized nanocrystalline cellulose (NCs) in order to improve membrane anti-fouling resistance against oil depositions. The characterization results demonstrated that the overall porosity and hydrophilicity of the membranes were improved significantly upon addition of NCs despite a decrease in the pore size of nanocomposite membranes. The UF performance results showed that the nanocomposite membrane incorporated with 1 wt% NCs achieved an optimal water flux improvement, i.e., approximately 43% higher than the pristine membrane. Such nanocomposite membrane also exhibited promising oil rejection (>98.2%) and excellent water flux recovery rate of ˜98% and ˜85% after one and four cycles of treating 250-ppm oil-in-water emulsion solution, respectively. The desirable anti-fouling properties of nanocomposite membrane can be attributed to the existence of hydrophilic functional groups (-OH) on the surface of membrane stemming from addition of NCs that renders the membrane less vulnerable to fouling during oil-in-water emulsion treatment.
This article presents an analysis of the influence of heat treatment on chitosan nanocomposite film. A series of samples comprising: pure chitosan film, chitosan film embedded with nanocrystalline cellulose (NCC), chitosan film crosslinked with tannic acid and chitosan film with a blend of NCC and tannic acid were heat treated using a convection oven. Fourier-transform-infrared spectroscopy (FTIR) and X-ray diffraction test (XRD) shows the changes in chemical interaction of the heat treated films. The heat treated films show significant improvements in moisture absorption. Tensile strength and Young's Modulus were increased up to 7MPa and 259MPa, respectively when the samples were subjected to heat treatment. For the NCC particles, a transmission electron microscope (TEM) was used to inspect the structural properties of cellulose particle in suspension form.
Chitin biopolymer has received significant attention recently by many industries as a green technology. Nanotechnology has been used to make chitin nanocrystals (ChiNCs) that are rod-shaped natural nanomaterials with nanoscale size. Owing to the unique features such as biodegradability, biocompatibility, renewability, rod-shape, and excellent surface and interfacial, physiochemical, and thermo-mechanical properties; ChiNCs have been green and attractive products with wide applications specifically in medical and pharmaceutical, food and packaging, cosmetic, electrical, and electronic, and also in the oil and gas industry. This review aims to give a comprehensive and applied insight into ChiNCs technology. It starts with reviewing different sources of chitin and their extraction methods followed by the characterization of ChiNCs. Furthermore, a detailed investigation into various complex fluids (dispersions, emulsions, foams, and gels) stabilized by ChiNCs and their characterisation have been thoroughly deliberated. Finally, the current status including ground-breaking applications, untapped investigations, and future prospective have been presented.
Olive fiber is a sustainable material as well as alternative biomass for extraction of nanocrystalline cellulose (NCC), which has been widely applied in various industries. In the present study, ONC-I, ONC-II, and ONC-III were extracted from olive stem fiber at different hydrolysis reaction times of 30 min, 45 min, and 60 min, respectively. The nanoparticle size was found gradually reducing from ONC-I (11.35 nm width, 168.28 nm length) to ONC-III (6.92 nm width, 124.16 nm length) due to the disintegration of cellulose fibrils. ONC-II and ONC-III possessed highly pure cellulose compartments and enhanced crystals structure. This study also showed that rigidity increased from ONC-I to ONC-II. ONC-III showed the highest crystallinity of 83.1 %, endowing it as a potentially reliable load-bearing agent. Moreover, ONC-III exhibited highest stable heat resistance among the chemically-isolated nanocellulose. We concluded that olive NCC could be promising materials for a variety of industrial applications in various fields.
The Box-Behnken design was applied to optimize the extraction of pectin from Averrhoa bilimbi (ABP) using deep eutectic solvents (DES). The four variables of extraction were percentage of DES (X1), extraction time (X2), temperature (X3), and molar ratio of DES components (X4). The quadratic regression equation was established as a predicted model with R2 value of 0.9375. The optimal condition was X1 = 3.74% (w/v), X2 = 2.5 h, X3 = 80 °C, and X4 = 1:1. No significant difference between the predicted (14.70%) and experimental (14.44%) maximum yield of sample was noted. Characterization of physico-chemical properties characterization of ABP was performed. The main components of ABP were galacturonic acids, arabinoses, and xyloses. ABP also showed good functional properties such as water holding capacity (3.70 g/g), oil holding capacity (2.40 g/g), and foaming capacity (133.33%). The results also showed that ABP exhibited free radical scavenging activity (41.46%) and ferric reducing antioxidant power (1.15 mM).
Current environmental concerns fostered a strong interest in extracting polymers from renewable feedstocks. Chitosan, a second most abundant polysaccharide after cellulose, may prove to be a promising green material owing to its renewability, inherent biodegradablity, natural availability, non-toxicity, and ease of modification. This review is intended to comprehensively overview the recent developments on the isolation of chitosan from chitin, its modification and applications as a reinforcing candidate for food packaging materials, emphasizing the scientific underpinnings arising from its physicochemical properties, antimicrobial, antioxidant, and antifungal activities. We review various chitosan-reinforced composites reported in the literature and comprehensively present intriguing mechanical and other functional properties. We highlight the contribution of these mechanically robust and responsive materials to extend the shelf-life and maintain the qualities of a wide range of food commodities. Finally, we assess critical challenges and highlight future opportunities towards understanding the versatile applications of chitosan nanocomposites.
Adsorption performance of chitosan (CS) hydrogel beads was investigated after impregnation of CS with hexadecylamine (HDA) as a cationic surfactant, for the elimination of reactive blue 4 (RB4) from wastewater. The CS/HDA beads formed with 3.8% HDA were the most effective adsorbent. The adsorption capacity was increased by 1.43 times from 317 mg/g (CS) to 454 mg/g (CS/HDA). The RB4 removal increased with decrease in the pH of dye solution from 4 to 9. The isotherm data obtained from RB4 adsorption on CS and CS/HDA are adequately described by Freundlich model (R(2)=0.946 and 0.934, χ(2)=22.414 and 64.761). The kinetic study revealed that the pseudo-second-order rate model (R(2)=0.996 and 0.997) was in better agreement with the experimental data. The negative values of ΔG° (-2.28 and -6.30 kJ/mol) and ΔH° (-172.18 and -101.62 kJ/mol) for CS beads and HDA modified CS beads, respectively; suggested a spontaneous and exothermic process for RB4 adsorption.
Hydrogels are an attractive system for a myriad of applications. While most hydrogels are usually formed from synthetic materials, lignocellulosic biomass appears as a sustainable alternative for hydrogel development. The valorization of biomass, especially the non-woody biomass to meet the growing demand of the substitution of synthetics and to leverage its benefits for cellulose hydrogel fabrication is attractive. This review aims to present an overview of advances in hydrogel development from non-woody biomass, especially using native cellulose. The review will cover the overall process from cellulose depolymerization, dissolution to crosslinking reaction and the related mechanisms where known. Hydrogel design is heavily affected by the cellulose solubility, crosslinking method and the related processing conditions apart from biomass type and cellulose purity. Hence, the important parameters for rational designs of hydrogels with desired properties, particularly porosity, transparency and swelling characteristics will be discussed. Current challenges and future perspectives will also be highlighted.
Starch-graft-acrylonitrile (ANS) is compounded with carboxylated nitrile butadiene rubber (XNBR) latex. The control XNBR and the ANS/XNBR latex films were prepared through a coagulant dipping process. The films were subjected to ageing and soil burial procedures. For the biodegradation experiment, the surface of the film was assessed after the 2nd, 4th and 8th week of soil burial. The ANS, XNBR, and ANS/XNBR colloidal stability were determined with a Malvern Zetasizer. For the dipped latex films, the mechanical, morphological and thermal properties were analyzed. The addition of ANS into the XNBR latex increased the stability of the colloidal dispersions, decreased the latex film tensile strength, but increased the elongation at break due to the bipolar interaction of the ANS and XNBR particles. The ANS/XNBR latex films aged faster than the control films while the morphological analysis showed the existence of a starch crystal region and the formation of microbial colonies on the surfaces of the films. Based on the TGA-DTA curves, a higher ΔT was observed for the ANS/XNBR latex films signifying high thermal energy needed for the film to thermally degrade.
Agar is a jelly-like biopolymer synthesized by many red seaweeds as their major cell wall component. Due to its excellent rheological properties, it has been exploited commercially for applications in food, cosmetic, pharmaceutical, biomedical and biotechnology industries. Despite its multiple uses, the biosynthesis of this phycocolloid is not fully understood. The current knowledge on agar biosynthesis is inferred from plant biochemistry and putative pathways for ulvan and alginate biosynthesis in green and brown seaweeds, respectively. In this review, the gaps in our current knowledge on agar biosynthetic pathway are discussed, focusing on the biosynthesis of agar precursors, elongation of agar polysaccharide chain and side chain modification. The development of molecular markers for the screening of desired seaweeds for industrial exploitation is also discussed.
Sulphated polysaccharides (SPs) are carbohydrate macromolecules with sulphate esters that are found among marine algae, seagrasses, mangroves and some terrestrial plants. The sulphate concentration in the ocean (28 mM) since ancient time could have driven the production of SPs in marine algae. SPs have a gelatinous property that can protect marine algae against desiccation and salinity stress. Agar and carrageenan are red algal SPs that are widely used as gelling agents in the food and pharmaceutical industries. The information on the SPs from freshwater and land plants are limited. In this review, we reviewed the taxonomic distribution and composition of SPs in different photosynthetic lineages, and explored the association of SP production in these diversified photosynthetic organisms with evolution history and environmental stresses. We also reviewed the genes/proteins involved in SP biosynthesis. Insights into SP biosynthetic machinery may shed light on the evolution that accompanied adaptation to life on earth.
Lauric acid was introduced into "Empty" V-type starch using a solid encapsulation method. The structural characteristics and emulsifying properties of the starch-fatty acid complex (SFAC) were explored as a function of the complexing temperature. X-ray diffraction and differential scanning calorimetry confirmed that SFAC was mainly composed of type-I amylose inclusion complexes. Contact angle measurements revealed that the hydrophobic properties of SFAC were closely related to the temperature-regulated complex index. The particle size range of SFAC gradually increased as the complexing temperature increased. The SFAC-stabilized Pickering emulsion at c of 5% and Φ of 40-60% possessed a small droplet size and long-term storage stability for up to 30 days, resulting from the formation of a gel-like network. This study provides new insight into the design of hydrophobic modified starch as a novel and multifunctional emulsifier and is of great help in the development of starch-based Pickering emulsion gels.
Nano-delivery systems have gained remarkable recognition for targeted delivery of therapeutic payload, reduced off-target effects, and improved biopharmaceutical profiles of drugs. Therefore, we aimed to fabricate polymeric nanoparticles (NPs) to deliver tacrolimus (TCS) to deeper layers of the skin in order to alleviate its systemic toxicity and improved therapeutic efficacy against atopic dermatitis (AD). To further optimize the targeting efficiency, TCS-loaded NPs were coated with hyaluronic acid (HA). Following the various physicochemical optimizations, the prepared HA-TCS-CS-NPs were tested for in vitro drug release kinetics, drug permeation across the stratum corneum, percentage of drug retained in the epidermis and dermis, and anti-AD efficacy. Results revealed that HA-TCS-CS-NPs exhibit sustained release profile, promising drug permeation ability, improved skin retention, and pronounced anti-AD efficacy. Conclusively, we anticipated that HA-based modification of TCS-CS-NPs could be a promising therapeutic approach for rationalized management of AD, particularly in children as well as in adults having steroid phobia.
Cross-linked enzyme aggregates (CLEAs) are influenced by mass diffusion limitations such as the degree of molecular cross-linking attained, which affects substrate accessibility. Thus, this study seeks to improve substrate accessibility using macromolecular cross-linkers in cross-linked levanase aggregates (CLLAs) formation for levan-type fructooligosaccharides (L-FOS) production. Dialdehyde starch-tapioca (DAST) was successfully developed and used to cross-link levanase to form CLLAs-D and with bovine serum albumin (BSA) to form CLLAs-DB which showed activity recoveries of 65.6% and 81.6%, respectively. After cross-linking, the pH (6-10) and thermal stability (30-40 °C) increased, and organic solvent tolerance resulted in the activation of CLLAs. Likewise, CLLAs-DB had higher substrate affinity and accessibility and a higher effectiveness factors than CLLAs-D. The total L-FOS yield of CLLAs-DB (78.9% (w/v)) was higher than that of CLLAs-D (62.4% (w/v)). Therefore, as a cross-linker, DAST may have application prospects as a promising and green biocatalyst for product formation.
The aim of the present research work has focused on investigating the effect of cellulose nanofibers (CNFs) and nano clays (montmorillonite (MMT) & organoclay (OMMT)) at 0.75Wt % on the performance of kenaf/epoxy composites. Mechanical (tensile and flexural) and thermal properties of composites in terms of morphology, thermal stability, weight loss, and dynamic mechanical properties were analyzed. The obtained results revealed that the integration of stiff CNFs as filler enhanced the mechanical and thermal properties, storage and loss modulus while a considerable decrease in Tan δ was realized compared to kenaf/epoxy composites. Enhancement in the properties was observed for OMMT and CNFs composites compared to MMT/kenaf/epoxy composites, which is attributed to the uniform filler distribution and interfacial adhesion between CNFs, OMMT, kenaf and epoxy matrix. The obtained results revealed that OMMT and CNFs based kenaf/epoxy composites can be an efficient alternative for construction applications.
The objective of this study is to compare the effect of two different isolation techniques on the physico-chemical and thermal properties of cellulose nanowhiskers (CNW) from oil palm biomass obtained microcrystalline cellulose (MCC). Fourier transform infrared analysis showed that there are no significant changes in the peak positions, suggesting that the treatments did not affect the chemical structure of the cellulose fragment. Scanning electron microscopy showed that the aggregated structure of MCC is broken down after treatment. Transmission electron microscopy revealed that the produced CNW displayed a nanoscale structure. X-ray diffraction analysis indicated that chemical swelling improves the crystallinity of MCC while maintaining the cellulose I structure. Acid hydrolysis however reduced the crystallinity of MCC and displayed the coexistence of cellulose I and II allomorphs. The produced CNW is shown to have a good thermal stability and hence is suitable for a range of applications such as green biodegradable nanocomposites reinforced with CNW.
Addition of doping materials can possibly enhance the ionic conduction of solid polymer electrolyte (SPE). In this work, a new SPE using 2-hydroxyethyl cellulose (2-HEC) incorporated with different ammonium nitrate (NH4NO3) composition was prepared via solution casting method. Studies of structural properties were conducted to correlate the ionic conductivity of 2-HECNH4NO3SPE using X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy. Encouraging result was obtained as the ionic conductivity increased about two orders of magnitude upon addition of 12wt% of NH4NO3. XRD analysis shows the most amorphous SPE was obtained at 12-NH4NO3. From FTIR spectra, the interactions between 2-HEC and NH4NO3were observed by the shifts of COH peak from 1355cm-1to 1330cm-1and the presence of new NH peak in the OH region. The spectrum has been validated theoretically using Gaussian software. The results obtained from this study corroborate that the complexes of 2-HEC and NH4NO3responsible to promote the ionic conductivity to the higher value.
Two solid biopolymer electrolytes (SBEs) systems of carboxymethyl cellulose doped ammonium chloride (CMC-AC) and propylene carbonate plasticized (CMC-AC-PC) were prepared via solution casting technique. The ionic conductivity of SBEs were analyzed using electrical impedance spectroscopy (EIS) in the frequency range of 50 Hz-1 MHz at ambient temperature (303K). The highest ionic conductivity of CMC-AC SBE is 1.43 × 10(-3)S/cm for 16 wt.% of AC while the highest conductivity of plasticized SBE system is 1.01 × 10(-2)S/cm when added with 8 wt.% of PC. TGA/DSC showed that the addition of PC had increased the decomposition temperature compared of CMC-AC SBE. Fourier transform infrared (FTIR) spectra showed the occurrence of complexation between the SBE components and it is proved successfully executed by Gaussian software. X-ray diffraction (XRD) indicated that amorphous nature of SBEs. It is believed that the PC is one of the most promising plasticizer to enhance the ionic conductivity and performance for SBE system.