Unripe and ripe bilimbi (Averrhoa bilimbi. L) were ground and the extracted juices were partially purified by ammonium sulfate precipitation at the concentrations of 40 and 60% (w/v). The collected proteases were analysed for pH, temperature stability, storage stability, molecular weight distribution, protein concentration and protein content. Protein content of bilimbi fruit was 0.89 g. Protease activity of both the unripe and ripe fruit were optimum at pH 4 and 40ºC when the juice were purified at 40 and 60% ammonium sulfate precipitation. A decreased in protease activity was observed during the seven days of storage at 4°C. Molecular weight distribution indicated that the proteases protein bands fall between 10 to 220 kDa. Protein bands were observed at 25, 50 and 160 kDa in both the unripe and ripe bilimbi proteases purified with 40% ammonium sulfate, however, the bands were more intense in those from unripe bilimbi. No protein bands were seen in proteases purified with 60% ammonium sulfate. Protein concentration was higher for proteases extracted with 40% ammonium sulfate at both ripening stages. Thus, purification using 40% ammonium sulfate precipitation could be a successful method to partially purify proteases from bilimbi especially from the unripe stage.
Collagen was extracted from catfish (Clarias gariepnus) waste using 0.5M acetic acid and its subsequent precipitation in 2.6M NaCl. The resultant collagen was analysed with respect to its moisture content and physicochemical properties including yield, pH, protein content, colour, odour and thermal stability. A yield of 16.4% and positive collagen attributes indicate that catfish waste has potential as a collagen source. The snowy white, crystal-like and light textured collagen comprises of 5.97% protein and 0.46% moisture, and exhibits a pH of 4.75. Sensory evaluation indicates that the collagen has a slight fishy odour. Viscosity analysis indicates a steady decrease with increasing temperature over the range considered (20-50°C). The pale colour exhibited and limited odour emitted by the extracted collagen indicate that catfish waste collagen could be applied in the food industry without resulting in any undesirable food products attributes. Differential Scanning Calorimetry (DSC) analysis indicated that the collagen exhibits good thermal stability and denatures at a high temperature in a similar manner to mammalian collagen.
Molecular self-assembly is ubiquitous in nature and has emerged as a new approach to produce new materials in chemistry, engineering, nanotechnology, polymer science and materials. Molecular self-assembly has been attracting increasing interest from the scientific community in recent years due to its importance in understanding biology and a variety of diseases at the molecular level. In the last few years, considerable advances have been made in the use of peptides as building blocks to produce biological materials for wide range of applications, including fabricating novel supra-molecular structures and scaffolding for tissue repair. The study of biological self-assembly systems represents a significant advancement in molecular engineering and is a rapidly growing scientific and engineering field that crosses the boundaries of existing disciplines. Many self-assembling systems are range from bi- and tri-block copolymers to DNA structures as well as simple and complex proteins and peptides. The ultimate goal is to harness molecular self-assembly such that design and control of bottom-up processes is achieved thereby enabling exploitation of structures developed at the meso- and macro-scopic scale for the purposes of life and non-life science applications. Such aspirations can be achieved through understanding the fundamental principles behind the selforganisation and self-synthesis processes exhibited by biological systems.
In this study, Hydrolysate from angelwing clam (Pholas orientalis) was produced at 0, 1, 2 and 3 hrs and E/S ratio of 0.5 and 3% using alcalase where the pH and temperature were kept constant at pH 8.5 and 60°C, respectively. The hydrolysates were analysed for antioxidant and functional properties such as solubility, emulsifying properties and water and oil holding capacity. Degree of hydrolysis (DH), yield, functional and antioxidant properties were influenced by the hydrolysis time and E/S ratio. Higher enzyme concentration (E/S 3%) and longer hydrolysis time increased the DH. Yield was higher at E/S 3% but reduced with hydrolysis time. Longer hydrolysis time produced more soluble hydrolysate and higher metal chelating activity but lower in emulsifying properties and DPPH activity. Higher enzyme concentration resulted in increase only in solubility and metal chelating activity. This study revealed that enzymatic hydrolysis using alcalase should be performed at shorter hydrolysis time using intermediate concentration of enzyme (E/S between 0.5 to 3%) in order to produce angelwing clam hydrolysate with collectively good functional and antioxidant properties
The state space modeling approach was developed to cope with the demand
and performance due to the increase in system complexity, which may have
multiple inputs and multiple outputs (MIMO). This approach is based on timedomain
analysis and synthesis using state variables. This paper describes the
development of a state space representation of a furnace system of a combined
cycle power plant. Power plants will need to operate optimally so as to stay
competitive, as even a small improvement in energy efficiency would involve
substantial cost savings. Both the quantitative and qualitative analyses of the
state space representation of the furnace system are discussed. These include
the responses of systems excited by certain inputs and the structural properties
of the system. The analysis on the furnace system showed that the system is
bounded input and bounded output stable, controllable and observable. In
practice, the state space formulation is very important for numerical computation
and controller design, and can be extended for time-varying systems.
This paper presents the development of a Graphical User Interface (GUI)
for calculating the sum of nail-fold (NF) and distal interphalangeal joint
(DIP) ratios for all ten fingers. The sum of NF:DIP ratios for all ten fingers
leads to the Digital Index (DI) that was used as the measure for identifying
and determining the presence of finger clubbing symptom. This GUI system
was developed to serve as a simple and user-friendly interface for clinicians
to calculate DI value of patients in a busy clinic practice. It is also equipped
with the capability to keep the patient’s past diagnosis medical check-up
data for future monitoring purposes. The result shows that the developed
system helps the clinicians to perform calculation of DI value and identify
the presence of finger clubbing in a very short time. The average time taken
to measure both NF and DIP circumferences using Finger Clubbing Meter,
and to compute DI values using Digital Index Evaluation System (DIES)
interface is 6:36 ± 1:24 minutes (Mean ± SD) .This system is expected to
contribute in detecting the finger clubbing problem at early stage of so the
treatment can be performed immediately.
This study focused on the identification of pathogenic bacteria in raw water intake and after sand filtration for drinking water treatment plant during flood event in 2014. The samples was collected from the Lubok Buntar Water Treatment Plant (WTP) and processed through bacterial isolation using chocolate agar as a media. The isolation process conducted based on serial samples dilution and streaking method prior to DNA extraction. Deoxyribonucleic acid (DNA) extraction kit was used to get selected bacteria DNA and further analysis using Polymerase Chain Reaction (PCR) test and electrophoresis to get DNA sequences. The Basic Local Alignment Search Tool (BLAST) analysis was employed to identify the species of the isolated bacteria. As a result, Pantoeaagglomerans and Enterobacter sp. were found in raw and filtered water sample and indicating the same family types. It was concluded that bacteria of the same species were found before and after sand filtration and need to be removed by disinfectant process. The findings also indicated that all the physicochemical parameters measured were within the values prescribed by the Interim National Water Quality Standard (INWQS).
Channel estimation techniques for Multiple-input Multiple-output Orthogonal Frequency Division Multiplexing (MIMO-OFDM) based on comb type pilot arrangement with least-square error (LSE) estimator was investigated with space-time-frequency (STF) diversity implementation. The frequency offset in OFDM impacts its performance. This was mitigated with the implementation of the presented inter-carrier interference self-cancellation (ICI-SC) techniques and different space-time subcarrier mapping. STF block coding in the system exploits the spatial, temporal and frequency diversity to improve performance. Estimated channel was fed into a decoder which combines the STF decoding together with the estimated channel coefficients using LSE estimator for equalization. The performance of the system is compared by measuring the symbol error rate with a PSK-16 and PSK-32. The results show that subcarrier mapping together with ICI-SC were able to increase the system performance. Introduction of channel estimation was also able to estimate the channel coefficient at only 5dB difference with a perfectly known channel.
Metakaolin is a manufactured pozzolan produced by thermal processing of purified kaolinitic clay using electrical furnace. This study has examined the effect of Metakaolin on the properties of cement and concrete at a replacement level of 0%, 5%, 10% and 15%. The parameters studied were divided into two groups which are chemical compositions, water requirement, setting time and soundness test were carried out for cementitous properties. Workability, compressive strength and bending strength were test for concrete properties. Hardened concrete was cured under different type of curing conditions and tested.. The result showed that the inclusions of Metakaolin as cement replacement minerals have change some of the cementitous and concrete properties. This research reveals, the optimum effect for cementitous and concrete properties for metakaolin was 10%.
Cyclic guanosine monophosphate (cGMP) is a second messenger molecule involved in the intracellular signalling mechanism which is important in a wide range of cellular process including metabolism, gene expression, cell proliferation and cell death. This study was conducted to determine the effect of fresh (FCC)) and thermoxidized carotino oil (TCO) on erythrocyte cGMP levels from Sprague dawley rats. A total of 30 Sprague dawley rats were randomly segregated into three groups: the first of which was placed on a Fresh Carotino Oil (FCO) diet, the second on a Thermoxidized Carotino Oil (TCO) diet and the control group on commercial rat chow only for a period of 6 and 9 weeks. The two oil diets comprised of 20% (w.10 of each oil mixed with commercial rat,feed. The enzyme immunoassays, performed in week 6, revealed that the erythrocytes cGMP levels for the FCO and TCO groups were 66.198±3.193 pmol/mL and 61.990±6.318 ptnol/mL respectively, and were significantly (p
This paper presents on ionic conductivity of MG30-PEMA blend solid polymer electrolytes (SPEs) prepared by solution cast technique. The analysis has shown that conductivity increases with the increasing salt composition. It is observed via x-ray diffraction analysis that the crystallinity of the sample decreased with the amount of salt composition as expected. It is also observed that the dielectric value increases with increasing amount of LiCF3SO3 in the sample. Surface morphology revealed that ion aggregation occurred after optimum conductivity which has lowered the conductivity.
Magnesium-based polymer gel electrolytes consist of magnesium triflate (MgTf) salt, a mixture of ethylene carbonate (EC) and diethyl carbonate (DEC) solvents as well as cellulose acetate as a polymeric agent were prepared via direct dissolution method. The highest ionic conductivity obtained for MgTf-EC:DEC(1:1) liquid electrolytes was 2.66 x 10-3 S cm-1 and enhanced to 2.73 x 10-3 S cm-1 with the addition of cellulose acetate. These results were in agreement with the activation energy obtained with the lowest value of 0.11. The best explanation on the enhancement in ionic conductivity of PGE is due to the “breathing polymeric chain model”. The plots of conductivity-temperature shown to obey an Arrhenius rule. The electrical properties of the sample with the highest conductivity were analyzed using electrical permittivity-based frequency and temperature dependence in the range of 100 Hz - 1 MHz and 303-373K, respectively. The variation in dielectric permittivity (εr and εi) as a function of frequency at different temperatures exhibited decays at higher frequencies and a dispersive behavior at low frequencies. Based on the observed electrical properties, it can be inferred that this polymer gel electrolyte could be a promising candidate as an electrolyte in electrochemical devices.
Increasing demands in palm oil industry hence resulting the production of palm oil to increase. It is then creating a major problem in disposing the waste to be treat in appropriate ways. The governments are forced to look for alternative technology for the palm oil mill effluent (POME) treatment because the demand of oil increases with the awareness on increasing environmental issue. Therefore, a new technology must be found in order to reduce energy consumption, to meet legal requirements on emission and for cost reduction and also increased quality of water treatment. Membrane Anaerobic System (MAS) is a promising alternative way to overcome these issues. In this study, the efficiency of the MAS performance increases to 99.03% in ten days operation. The application of Monod, Contois and Chen & Hashimoto models were used to analyze the performance of MAS for treating POME. The results from the experiment show the substrate removal model is well fits for estimation of kinetics membrane anaerobic system. Amongst them, the Contois and Monod models predicted the bio-kinetic reactions of the MAS very well with coefficient of determination (R2>97%) values. The MAS bioreactor was creating to be an improvement method as well as successful biological treatment since the graph shows linearized which is good agreement with reported in literature.
To ascertain the level of knowledge among primary school teachers towards the management of traumatic dental injuries (TDIs) in school and to determine the preference among teachers regarding the education tools that can be used to increase awareness and knowledge among them. A total of 150 teachers from primary schools in three different districts were included in the study and they were given self-administered questionnaires to be filled. The validated questionnaire was distributed randomly in the selected schools. The questionnaire included two scenarios comprising of tooth fracture and avulsion. Questions regarding awareness and management of these scenarios were asked. All 150 participants answered the questionnaire; of these 74% were females 26% were males. 64% of the participants had received tertiary education. Although 70% of teachers had obtained first aid training, only 9.3% of them had received training regrading dental injuries. About 53% of participants knew the correct answer for the appropriate response to fractured tooth and only 35.3% managed to correctly answer the question related to appropriate response to an avulsed tooth. Only 38.7% knew about appropriate rinsing solution and a mere 4.7% were familiar with proper storage media. Even though the teachers have poor knowledge regarding management of dental injuries, it is reassuring to know that 93% of them are keen on further training and awareness. More educational programmes need to be introduced to empower the teachers with the relevant knowledge required to deal with dental emergencies.
Composite panels were manufactured from kenaf particles and treated with two different alkali treatments using 2% NaOH and 2% KOH with resin contents of 8% and 10% of phenol formaldehyde (PF) at medium density of 650kg/m3. The objectives of this study were to determine the mechanical properties in terms of its modulus of rupture (MOR), modulus of elasticity (MOE) and internal bond (IB), and physical properties namely thickness swelling (TS) and water absorption (WA) of treated kenaf board. The mechanical and physical tests were performed according to the Malaysian Standard (MS1787:2004). The minimum requirements value for MOE, MOR and IB were 2000 MPa, 14 MPa and 0.45 MPa respectively for furniture grade particleboards for use in humid conditions (PF2). According to Malaysian specifications for physical properties, the maximum requirement for thickness swell is 15%. Results indicated that both treated boards with NaOH and KOH showed an increase in strength properties compared to untreated particleboard. Particleboard treated with KOH exhibited the highest MOR and MOE values, while board with NaOH treatment gave the highest IB value. The boards with treated particles gave better performance in terms of physical properties. There were no significant differences in mechanical properties (MOR, MOE and IB) and physical properties for the different alkali treatment. The values of bending strength and IB strength increased with an increase in resin content, while TS and WA increased with a decrease in resin content. In conclusion, NaOH and KOH treated kenaf particles improved board performance and could be considered as an alternative material for particleboard production.
Palm Oil Mill Effluent (POME) is the largest contributor of biomass from
the palm oil milling industry. Conventional method of POME treatment
using ponding system should be improved because of huge land resource
requirement. In this study, microbubbles technology was applied to
understand the recovery rate of residual oil from POME at different
operating temperatures. Temperature for POME was set at 27 oC, 30 oC and
50 oC to determine the microbubble size distributions and characteristics at
different POME temperature. At each temperature, the size of microbubbles
was measured based on six size range; 50 μm. The results showed that at different
temperatures, the microbubbles size distribution varies and the smallest
group of microbubbles (
A series of Schiff base ligand, SALMPD, and its mono- and trinuclear Zn(II) metal complexes were synthesised from m-phenylenediamine and salicylaldehyde in alcoholic solution. The synthesis of ligand and mononuclear complex were synthesised using conventional condensation method, while the trinuclear complex was done using microwave-assisted synthesis method. The structure of each compound was elucidated by elemental analysis, infrared and ¹H NMR spectroscopy. The infrared spectrum of SALMPD shows a strong azomethine (C=N) band at 1621.62c m⁻¹, indicates the formation of the ligand. Upon complexation of the mononuclear complex, the C=N infrared band shifted and the disappearing of the phenolic hydrogen signal in ¹H NMR suggesting the chelation between Zinc(II) metal ion and ligand took place when azomethine and phenolic hydrogen deprotonated. The trinuclear complex, Zn3(SALMPD) obtained was consist of two moieties of mononuclear Zn₃(SALMPD), which act as ligands that chelating to the third Zn(II) metal ion through oxygen atom due to the shifting of M-O infrared band from 575.12-540.53cm⁻¹, which serves as a coordination site for the metal ion.
Storytelling is considered as an interactive social arts that uses word and
gestures to reveal the elements and images of a story while engaging the
listener's imagination. Multimedia based digital storytelling learning
approach provides interesting, interactive, engaging and multisensory
learning experience to children. Children explore new experience and
scenarios as new stories are being told. This study concentrates on
determining the best combination of elements for designing effective digital
storytelling applications specifically for the usage of dyslexic children.
Dyslexic children are known to have a common learning difficulty that can
cause problems with reading, writing, spelling and comprehension. These
applications are design with the objective to help in improving dyslexic
children ability in readings and comprehensions. Four elements were
derived from extensive literature studies. The elements are multimedia
components, multi-sensory instructional approach, emotional design and
games design. The relationship among all the elements were determine
and described in details as it will be used to contribute to the design and
development of the application in further works. The strength of this study
is it models the combinations of technology, psychology and instructional
approach as a support components for developing an effective digital story
telling learning application for dyslexic children.
Recently, research and development in the field of drug delivery systems (DDS) facilitating site-specific therapy has reached significant progression. DDS based on polymer micelles, coated micro- and nanoparticles, and various prodrug systems including water-soluble polymer have been prepared and extensively studied as novel drugs designed for cancer chemotherapy and brain delivery. Since polymers are going to be used in human, this study has the interest of testing two types of polymer, polyimides (PI) and polyphenylenevinylene (PPV) on neuronal cells. The objective of this study was to determine the possible neurotoxicity and potential neuroprotective effects of PI and PPV towards SH-SY5Y neuronal cells challenged by hydrogen peroxide (1120) as an oxidant. Cells were pretreated with either PI or PPV for 1 hour followed by incubation for 24 hour with 100 ,uM of 11201. MTS • assay was used to assess cell viability. Results show that PI and PPV are not harmful within the concentration up to 10 pM and 100 pM, respectively. However, PI and PPV do not protect neuronal cells against toxicity induced by H2O, or further up the cell death.
The cloud point extraction (CPE) method was developed to determine the zinc prior to Ultraviolet-visible (UV-Vis) spectrophotometry detection. Triton X-100was applied as extractant based on the complexation reaction of Zn(II) ions with ethylenediaminetetraacetic acid (EDTA). Under optimal conditions, the CPE was used to determine the concentration of zinc in canned food samples. The amounts of zinc found in the food samples were in the range of 0.005-0.007 mg/L with RSD of < 8 %. This confirmed that the proposed CPE method is suitable for the determination of zinc in food samples, indicating the concentration of zinc was within the permissible limit.