Tropical greenhouses require active evaporative cooling system such as pad-and-fan to ensure a suitable microclimate for crop production. Excess heat causes indoor temperature to become hotter than desired resulting in detrimental effects to crop growth and production. Solar radiation intensity and outside temperature affect temperature and relative humidity level inside a greenhouse, while wide gradients in temperature and relative humidity can cause problems related to crop growth and production uniformity. A 300 m2 greenhouse, equipped with evaporative pad and four exhaust fans at each end walls, was used in the study. Horizontal and vertical profiles of the temperature and relative humidity inside the greenhouse were investigated. Results showed that temperature increased from evaporative pad area to exhaust fans area in a horizontal plane, while relative humidity showed an inverse pattern from temperature. In the vertical plane, temperature increased, while relative humidity decreased from lower level to the upper level. ANOVA results showed that in overall, temperature and relative humidity inside the greenhouse were uniform as there was no significant difference at 95% confidence interval. Thus, it was concluded that greenhouse cooling system by evaporative pad and exhaust fans are suitable for application in a tropical country such as Malaysia.
Stack ventilation in the hot and humid climate is inherently inefficient due to minimal air temperature differences between indoor and outdoor environment of a naturally ventilated building. Solar induced ventilation is a viable alternative in enhancing this stack ventilation. This paper aims to demonstrate investigations on the effective solar collector orientation and stack height for a solar induced ventilation prototype that utilizes roof solar collector and vertical stack. The orientation of the solar collector is significant as it determines the amount of solar radiation absorbed by the solar collector. Meanwhile, the height of the vertical stack influences the creation of the stack pressure in inducing air movement. Investigations were executed using a simulation modelling software called FloVENT. The validation of the simulation modelling against physical experiment indicated a good agreement between these two results. Analyses were executed on the air temperature increments inside the solar collector. A high increment of the air temperature resulted in the effective orientation. Meanwhile, the air temperature and mass flow rate of the various heights of the vertical stack were also analyzed. The findings concluded that the recommended orientation for the prototype’s solar collector is the west-facing orientation. It was also found that the higher the vertical stack, the lower the air temperature inside the stack would be, but with greater induced mass flow rate.
This paper presents the numerical modelling techniques for the simulation of the energy conversion chain from wave to electricity in an Oscillating Water Column (OWC) equipped with a full-scaled self rectifying turbine. The performance of the OWC device has been assessed for the stand-alone power system of a typical Irish climatic wave condition. The results showed that the overall performance of the complete device depends on the level of turbine damping, which in turn depends on the wave climate, especially the significant wave height. Furthermore, turbine efficiency predicted using quasi-steady showed qualitatively favourable agreement with the experimental results.
Simultaneous removal of SO2 and NO from simulated flue gas by cerium oxide supported over palm shell activated carbon (Ce/PSAC) was studied in a fixed bed adsorber. In this study, the adsorption breakthrough of SO2 and NO on Ce/PSAC at different reaction temperatures was manipulated to test their applicability to a model developed by Yoon and Nelson (1984) for breakthrough curves. Yoon and Nelson (1984) developed a relatively simple model addressing the adsorption and breakthrough of adsorbate vapour with respect to activated charcoal. This model was based on the assumption that the rate of decrease in the probability of adsorption for each adsorbate molecule is proportional to the probability of adsorbate adsorption and the probability of adsorbate breakthrough on the adsorbent. A regression analysis (least square method) has been used to give the model parameters of k and t1/2. The results showed that the agreement between the model and the experimental results is satisfactory. From the observation, it is concluded that the simple two-parameter model of Yoon and Nelson’s model can be applied for modelling the breakthrough curves of SO2 and NO gas adsorption over Ce/PSAC.
The composite nature of Ennore Creek, receiving polluted waters from Buckingham canal, River Kortalaiyar, and the presence of numerous industries rapidly degrade the coastal environment. In this study, multivariate statistical technique was used to assess the nature of pollution and to identify the factors responsible for the enrichment of trace metals in the creek sediments. Forty samples were collected during pre- and post-monsoon periods to evaluate the seasonal variations on the concentration of trace metals in the sediments. The results indicate that not much seasonal variation exists in the concentration of trace metals in the sediments of Ennore creek. Results of the cluster analysis illustrate that the enrichment of trace metals was mainly from anthropogenic sources. Meanwhile, correlation coefficient among the metals reveals that some of the metals (Fe and Al) derived were of natural origin. The complex data matrix of the sediment were interpreted after reduction to three factors and the results illustrate the extent of the influence of anthropogenic activities. The spatial distribution diagrams demonstrate and demarcate the region of enrichment of metals in the sediments of Ennore creek.
Surface water samples were collected from 16 Lakes in and around Miri City to assess the electrochemical parameters includes pH, Electrical conductivity (EC), Total dissolved solid (TDS), redox potential (Eh), resistivity and salinity. Sampling locations for monitoring were selected in the vicinity of major roads, industries, settlements and agricultural region. Interpretation of data shows that the surface water in the central region of the study area is polluted by various anthropogenic activities, while in the southern part is within the limits of guideline values. This kind of investigation is essential in the study area to save the resources for future perspective. Further detailed studies are also needed to get a clear picture of the surface water quality in Miri city and for future sustainable management of this resource.
Bifurcation and chaos are important phenomena affecting many physical and chemical systems. They are also related to the stability/instability and multiplicity phenomena associated with these systems. The phenomena are not only of theoretical/mathematical interest but are also important for laboratory, pilot plant and commercial units. This paper concentrates on 3 systems:
1. The novel auto-thermic Circulating Fluidized Membrane Steam Reformer (CFBMSR) for the efficient production of the clean fuel hydrogen and which shows multiplicity of the steady state (static bifurcation)
2. A novel fermentor for the efficient production of bio-ethanol that shows static/dynamic bifurcation as well as chaotic behaviour
3. The neurocycle of the acetylcholine transmitter in the brain using diffusion-reaction models in order to gain insight into their possible connection to Alzheimer and Parkinson Diseases (AD/PD); these are preliminary efforts to investigate the bifurcation and chaotic behaviour of this neurocycle.
In this study, various methods and applications of flat plate solar collectors are discussed and pictorial representations are presented. Low temperature applications of flat plate collectors are identified in solar cooking, solar water heating, space and air heating, industrial heating plants and in agricultural produce drying processes. Basic equations, as presented by many researchers in the performances of flat plate collectors, are also presented. The review discusses the analysis of losses from flat plate collectors towards obtaining the overall heat loss coefficient which indicate the performance of flat plate collectors.
The aim of this study was to compare physical activity prevalence estimates among the International Physical Activity Questionnaire (IPAQ), steps/day, and accelerometer in a sample of government employees in Kangar, Perlis, Malaysia. Ten government agencies in Kangar were randomly chosen, and all employees were invited to participate. A self-administered questionnaire was employed to obtain information on socio-demographic characteristics and a physical activity assessment using the IPAQ. Anthropometric measurements, which include measurements of weight, height, body mass index, percent body fat, waist and hip circumference, were carried out. An accelerometer was used to assess total daily energy expenditure and the number of steps/day. A total of 272 respondents were involved in this study with a response rate of 83.2%. According to IPAQ, accelerometer and steps/day, the majority of the respondents (22.0%, 55.1%, and 77.6%, respectively) were classified as sedentary. The agreement between physical activity level as determined by the accelerometer vs. the IPAQ (Kappa=-0.46 {95% CI -0.384,-0.536}, p=0.238) and the IPAQ vs. steps/day (Kappa =0.037 {95% CI 0.090,-0.016}, p=0.175) was not significant, but the agreement between physical activity level as determined by the accelerometer vs. steps/day was classified as fair (Kappa=0.296 (95% CI 0.392, 0.200}, p
Extreme Value Theory (EVT) is a statistical field whose main focus is to investigate extreme phenomena. In EVT, Fréchet distribution is one of the extreme value distributions and it is used to model extreme events. The degree of fit between the model and the observed values was measured by Goodness-of-fit (GOF) test. Several types of GOF tests were also compared. The tests involved were Anderson-Darling (AD), Cramer-von Mises (CVM), Zhang Anderson Darling (ZAD), Zhang Cramer von-Mises (ZCVM) and Ln. The values of parameters μ, σ and ξ were estimated by Maximum Likelihood. The critical values were developed by Monte-Carlo simulation. In power study, the reliability of critical values was determined. Besides, it is of interest to identify which GOF test is superior to the other tests for Fréchet distribution. Thus, the comparisons of rejection rates were observed at different significance levels, as well as different sample sizes, based on several alternative distributions. Overall, given by Maximum Likelihood Estimation of Fréchet distribution, the ZAD and ZCVM tests are the most powerful tests for smaller sample size (ZAD for significance levels 0.05 and 0.1, ZCVM for significance level 0.01) as compared to AD, which is more powerful for larger sample size.
A study on the distribution of Recent Ostracoda in offshore sediment was carried out around the South China Sea. A total of 30 sediment samples were taken from the sampling stations between latitude 1°48’ and 7°25’N and longitude 102°09’ and 105°16’E. From this study, 79 species of ostracods belonging to 16 families and 44 genera were identified. The dominant species was Foveoleberis cypraeoides with 937 individuals obtained. There were 13 to 43 species in total. Diversity Index, H(s), was in the range of 2.1 to 3.3, whereas the dominance values were between 4.4 and 14.7%. Several environmental parameters were measured including depth, temperature and salinity. The range values for each of these parameters are 13-72 m, 25.24-30.06o C and 27.74-34.91 ppt, respectively. The sediment texture in this study area can be categorized as sand, sandy mud, clayey mud, silty mud, silty clay, clayey sand, clayey silt and silty sand. The observations revealed that abundance and diversity of ostracod appeared to be principally controlled by depth. Two faunal assemblages were identified in terms of faunal composition, namely, shallow water (Hemikrithe orientalis, Neomonoceratina iniqua, Stigmatocythere indica, Cytherelloidea leroyi and Neocytheretta snellii) and deep water (Paracypris sp., Alataconcha pterogona, Bythocytheropteron alatum, Keijella paucipunctata and Actinocythereis scutigera). A comparative analysis showed a high degree resemblance between the study area and south-eastern Malay Peninsula (the South China Sea).
HCFCs, in addition to destroying the ozone layer, have been recognized as a contributing factor that increases global warming. It is widely used as working fluid in window air-conditioning system, where capillary tube serves as an expansion device. Literature reports have shown that no single refrigerant can solve the problem of ozone layer depletion and global warming. Refrigerant HC290/HC600a/HFC407C mixture, an eco-friendly refrigerant, has been recognized as an alternative to HCFC22. The objective of this study is to, for cost effectiveness, develop an empirical correlation to predict the refrigerant HC290/ HC600a/HFC407C mixture mass flow rate using statistical experimental design approach. A review of relevant literature shows that refrigerant’s mass flow rate depends on condensing temperature, degree of subcooling, inner diameter and length of capillary tube. The relationship between the mass flow rate and the four independent variables was established as an empirical mathematical correlation using central composite design (CCD), a response surface methodology (RSM). This empirical correlation was examined using analysis of variance (ANOVA) of 5% level of significance. The results of these analysis showed that the correlation fitted well with the experimental data yielding an average and standard deviation of 1.05% and 2.62%, respectively. The validity of the present correlation was further assessed by comparing it with published empirical correlation in literature and the result showed that the present correlation is consistent.
During recent years, extensive development has been made to improving vaccines for tuberculosis. This is due to the presence of genome sequences of diverse mycobacterial species and Mycobacteroum tuberculosis (M. tuberculosis) isolates which has led to advances in the characterization of genes and antigens of M. tb and better realization of protective immune responses to the disease in both animals and humans. This review summarizes vaccine types, reasons for variable efficacy of BCG, latest advances in tuberculosis vaccine development and major vaccine design strategies.
Self-care behaviour involves all activities type 2 diabetes patients engage in to care for their disease. In our local population, however, most patients do not manage their disease appropriately. This study aimed to determine the level of self-care behaviour and to examine the differences in self-care behaviour according to type 2 diabetes patients’ demographic data and health condition at University Malaya Medical Centre. Sample of this study comprised 388 patients (respondents) and data were collected from December 2010 to February 2011 using self-administered questionnaires. Results showed that the level of self-care behaviour was moderately high (mean = 38.94, SD=11.93). There were significant differences between self-care behaviour and ethnicity [Wilk’s Lambda = 0.92, F(12, 1008) = 2.70, p < 0.05], age group [Wilk’s Lambda = 0.96, F(4, 383) = 4.39, p < 0.05], education level [Wilk’s Lambda = 0.94, F(12, 1008) = 1.85, p < 0.05], type of treatment [Wilk’s Lambda = 0.92, F(12, 1008) = 2.84, p < 0.05], health education [Wilk’s Lambda = 0.97, F(4, 383) = 3.33, p< 0.05]. Respondents who are Indian, elderly, had lower level of education, on insulin treatment, had received health education on diabetes and not smoking had better self-care behaviour scores. It can be concluded that high risk type 2 diabetes patients should be taught individually so as to help them improve physical and psychological outcome.
Study site: diabetic clinic; medical, nephrology, orthopedic, and surgery wards, University Malaya Medical Centre (UMMC)
Elliptic curve cryptosystems (ECC) provides better security for each bit key utilized compared to the RSA cryptosystem. For this reason, it is projected to have more practical usage than the RSA. In ECC, scalar multiplication (or point multiplication) is the dominant operation, namely, computing nP from a point P on an elliptic curve, where n is an integer defined as the point resulting from adding P + P + ... + P, n times. However, for practical uses, it is very important to improve the efficiency of the scalar multiplication. Solinas (1997) proposes that the τ-adic Non-Adjacent Form (τ-NAF) is one of the most efficient algorithms used to compute scalar multiplications on Anomalous Binary curves. In this paper, we give a new property (i.e., Theorem 1.2) of τ-NAF(n) representation for every length, l. This is useful for evaluating the maximum and minimum norms occurring among all length-l elements of Z(τ). We also propose a new cryptographic method by using randomization of a multiplier n to nr an element of Z(τ). It is based on τ-NAF. We focused on estimating the length of RTNAF(nr) expansion by using a new method.
Detailed geophysical investigations have been carried out using integrated geophysical methods with a view to characterising the subsurface lithologic features that might indicate suitable places for structural developments. An overview of the subsurface resistivity distribution has been achieved employing 8Vertical Electrical Soundings with the Schlumberger array and 4 2D resistivity imaging using Wenner array. In order to constrain the results of the electrical resistivity methods, we carried out a ground magnetic survey along E-W direction using the Proton precession magnetometer at 1m sampling interval. Analysis of well logs data available and VES results showed 4 to 5 geoelectric layers corresponding to sand, clayey sand, clay, silty sand and sandy clay. The 2D resistivity imaging sections showed relative decrease of apparent resistivity with depth implying a geological transition from sand with high resistivity value of about 508Ωm to clay with low resistivity value 16Ωm at depths of 0-20m and 25-50m respectively. The magnetic profiles showed that the study area was characterised by short wavelengths and amplitudes ranging from –3800 to 700 nT. The highs and lows of the magnetic responses occasioned by lithological variations and structural features were magnetically resolved. In view of the identified subsurface structures, the suggested depth to the competent layer is about 20m for low to medium structures while above 50m would be suitable for heavy or massive engineering structures. The use of integrated geophysical methods for the delineation, identification and imaging of the subsurface geological structures which could provide clues to the nature and type of foundation suitable for the development of the study area has been successfully achieved.
Lansium domesticum Corr. is a fruit tree of the Meliaceae family, which is commonly found in SouthEast Asia with a wide range of varieties. This study investigated three varieties of L. domesticum; Duku, Langsat and Dokong for the phytochemical screening and antimicrobial activity. Seeds from the matured fruits were extracted using hexane, methanol and water. The crude extracts were screened for antimicrobial activities toward three bacteria, namely, Pseudomonas aeruginosa, Bacillus subtilis, and Staphylococcus aureus. The findings showed that Langsat seed extracts contained more groups of compounds compared with the other two varieties, and its methanol extract demonstrated the highest inhibition zones against the three bacteria. The crude methanol extract of Duku seeds showed inhibition zones only towards Bacillus subtilis at a high concentration (1.0 mgL-1), whilst the seed extracts of Dokong showed no inhibition zones towards any of the tested bacteria.
The objective of this study was to investigate the capabilities of low-cost digital cameras in volume determination. Low-cost digital cameras are capable of many applications including aerial photogrammetry and close-range photogrammetry. Low-cost digital cameras have the potential to be used in landslide monitoring and mapping. In this study, a low-cost digital camera was used as a tool to acquire digital images of a model of a simulated landslide. The model was constructed using cement and sand with the dimensions of 3m in length and 1m width. Digital images of the simulated model were acquired using the technique of aerial photogrammetry and were subsequently processed using digital photogrammetric software. A portion of the simulated model was excavated to simulate a landslide and volume determination was carried out for the excavated sand. The results showed that low-cost digital cameras can be used in photogrammetric application including volume determination.
Detecting semantic events in sports video is crucial for video indexing and retrieval. Most existing works have exclusively relied on video content features, namely, directly available and extractable data from the visual and/or aural channels. Sole reliance on such data however, can be problematic due to the high-level semantic nature of video and the difficulty to properly align detected events with their exact time of occurrences. This paper proposes a framework for soccer goal event detection through collaborative analysis of multimodal features. Unlike previous approaches, the visual and aural contents are not directly scrutinized. Instead, an external textual source (i.e., minute-by-minute reports from sports websites) is used to initially localize the event search space. This step is vital as the event search space can significantly be reduced. This also makes further visual and aural analysis more efficient since excessive and unnecessary non-eventful segments are discarded, culminating in the accurate identification of the actual goal event segment. Experiments conducted on thirteen soccer matches are very promising with high accuracy rates being reported.
This paper investigates and determines the solutions for the Diophantine equation x2 + 4.7b = y2r, where
x, y, b are all positive intergers and r > 1. By substituting the values of r and b respectively, generators of
x and yr can be determined and classified into different categories. Then, by using geometric progression
method, a general formula for each category can be obtained. The necessary conditions to obtain the
integral solutions of x and y are also investigated.