This review article explores utilization of banana waste (fruit peels, pseudo-stem, trunks, and leaves) as precursor materials to produce an adsorbent, and its application against environmental pollutants such as heavy metals, dyes, organic pollutants, pesticides, and various other gaseous pollutants. In recent past, quite a good number of research articles have been published on the utilization of low-cost adsorbents derived from biomass wastes. The literature survey on banana waste derived adsorbents shown that due to the abundance of banana waste worldwide, it also considered as low-cost adsorbents with promising future application against various environmental pollutants. Furthermore, raw banana biomass can be chemically modified to prepare efficient adsorbent as per requirement; chemical surface functional group modification may enhance the multiple uses of the adsorbent with industrial standard. It was evident from a literature survey that banana waste derived adsorbents have significant removal efficiency against various pollutants. Most of the published articles on banana waste derived adsorbents have been discussed critically, and the conclusion is drawn based on the results reported. Some results with poorly performed experiments were also discussed and pointed out their lacking in reporting. Based on literature survey, the future research prospect on banana wastes has a significant impact on upcoming research strategy.
Polyelectrolyte composite nanospheres are relatively new adsorbents which have attracted much attention for their efficient pollutant removal and reuse performance. A novel polyelectrolyte nanosphere with magnetic function (SA@AM) was synthesized via the electrostatic reaction between the polyanionic sodium alginate (SA) and the surface of a prepared terminal amino-based magnetic nanoparticles (AMs). SA@AM showed a size of 15-22 nm with 6.85 emu·g-1 of magnetization value, exhibiting a high adsorption capacity on Pb(II) ions representing a common heavy metal pollutant, with a maximum adsorption capacity of 105.8 mg g-1. The Langmuir isotherm adsorption fits the adsorption curve, indicating uniform adsorption of Pb(II) on the SA@AM surfaces. Repeated adsorption desorption experiments showed that the removal ratio of Pb(II) by SA@AM was more than 76%, illustrating improved regeneration performance. These results provide useful information for the production of bio-based green magnetic nano scale adsorption materials for environmental remediation applications.
Soil erosion hazard is one of the prominent climate hazards that negatively impact countries' economies and livelihood. According to the global climate index, Sri Lanka is ranked among the first ten countries most threatened by climate change during the last three years (2018-2020). However, limited studies were conducted to simulate the impact of the soil erosion vulnerability based on climate scenarios. This study aims to assess and predict soil erosion susceptibility using climate change projected scenarios: Representative Concentration Pathways (RCP) in the Central Highlands of Sri Lanka. The potential of soil erosion susceptibility was predicted to 2040, depending on climate change scenarios, RCP 2.6 and RCP 8.5. Five models: revised universal soil loss (RUSLE), frequency ratio (FR), artificial neural networks (ANN), support vector machine (SVM) and adaptive network-based fuzzy inference system (ANFIS) were selected as widely applied for hazards assessments. Eight geo-environmental factors were selected as inputs to model the soil erosion susceptibility. Results of the five models demonstrate that soil erosion vulnerability (soil erosion rates) will increase 4%-22% compared to the current soil erosion rate (2020). The predictions indicate average soil erosion will increase to 10.50 t/ha/yr and 12.4 t/ha/yr under the RCP 2.6 and RCP 8.5 climate scenario in 2040, respectively. The ANFIS and SVM model predictions showed the highest accuracy (89%) on soil erosion susceptibility for this study area. The soil erosion susceptibility maps provide a good understanding of future soil erosion vulnerability (spatial distribution) and can be utilized to develop climate resilience.
Sequencing batch reactor (SBR) is one of the various methods of biological treatments used for treating wastewater and landfill leachate. This study investigated the treatment of landfill leachate and domestic wastewater by adding a new adsorbent (powdered ZELIAC; PZ) to the SBR technique. ZELIAC consists of zeolite, activated carbon, lime stone, rice husk ash, and Portland cement. The response surface methodology and central composite design were used to elucidate the nature of the response surface in the experimental design and describe the optimum conditions of the independent variables, including aeration rate (L/min), contact time (h), and ratio of leachate to wastewater mixture (%; v/v), as well as their responses (dependent variables). Appropriate conditions of operating variables were also optimized to predict the best value of responses. To perform an adequate analysis of the aerobic process, four dependent parameters, namely, chemical oxygen demand (COD), color, ammonia-nitrogen (NH3-N), and phenols, were measured as responses. The results indicated that the PZ-SBR showed higher performance in removing certain pollutants compared with SBR. Given the optimal conditions of aeration rate (1.74 L/min), leachate to wastewater ratio (20%), and contact time (10.31 h) for the PZ-SBR, the removal efficiencies for color, NH3-N, COD, and phenols were 84.11%, 99.01%, 72.84%, and 61.32%, respectively.
Remediation by algae is a very effective strategy for avoiding the use of costly, environmentally harmful chemicals in wastewater treatment. Recently, industries based on biomass, especially the bioenergy sector, are getting increasing attention due to their environmental acceptability. However, their practical application is still limited due to the growing cost of raw materials such as algal biomass, harvesting and processing limitations. Potential use of algal biomass includes nutrients recovery, heavy metals removal, COD, BOD, coliforms, and other disease-causing pathogens reduction and production of bioenergy and valuable products. However, the production of algal biomass using the variable composition of different wastewater streams as a source of growing medium and the application of treated water for subsequent use in agriculture for irrigation has remained a challenging task. The present review highlights and discusses the potential role of algae in removing beneficial nutrients from different wastewater streams with complex chemical compositions as a biorefinery concept and subsequent use of produced algal biomass for bioenergy and bioactive compounds. Moreover, challenges in producing algal biomass using various wastewater streams and ways to alleviate the stress caused by the toxic and high concentrations of nutrients in the wastewater stream have been discussed in detail. The technology will be economically feasible and publicly accepted by reducing the cost of algal biomass production and reducing the loaded or attached concentration of micropollutants and pathogenic microorganisms. Algal strain improvement, consortium development, biofilm formation, building an advanced cultivation reactor system, biorefinery concept development, and life-cycle assessment are all possible options for attaining a sustainable solution for sustainable biofuel production. Furthermore, producing valuable compounds, including pharmaceutical, nutraceutical and pigment contents generated from algal biomass during biofuel production, could also help reduce the cost of wastewater management by microalgae.
Palm oil production is one of the major industries in Malaysia and this country ranks one of the largest productions in the world. In Malaysia, the total production of crude palm oil in 2008 was 17,734,441 tonnes. However, the production of this amount of crude palm oil results in even larger amounts of palm oil mill effluent (POME). In the year 2008 alone, at least 44 million tonnes of POME was generated in Malaysia. Currently, the ponding system is the most common treatment method for POME but other processes such as aerobic and anaerobic digestion, physicochemical treatment and membrane filtration may also provide the palm oil industries with possible insights into the improvement of POME treatment processes. Generally, open ponding offers low capital and operating costs but this conventional method is becoming less attractive because the methane produced is wasted to the atmosphere and the system can not be certified for Carbon Emission Reduction trading. On the other hand, anaerobic digestion of POME provides the fastest payback of investment because the treatment enables biogas recovery for heat generation and treated effluent for land application. Lastly, it is proposed herewith that wastewater management based on the promotion of cleaner production and environmentally sound biotechnologies should be prioritized and included as a part of the POME management in Malaysia for attaining sustainable development. This paper thus discusses and compares state-of-the-art POME treatment methods as well as their individual performances.
Plastic pollution poses a significant environmental threat, particularly to marine ecosystems, as conventional plastics persist without degradation, accumulating plastic waste in landfills and natural environments. A promising alternative to address this issue involves the use of hydrogen donor solvents in plastic liquefaction, offering a dual benefit of waste reduction and the generation of valuable liquid products with diverse industrial applications. This review delves into plastic recycling methods with a specific focus on liquefaction using hydrogen donating solvents as an innovative approach to waste management. Liquefaction, conducted at moderate to high temperatures (280-450 °C) and pressures (7-30 MPa), yields high oil conversion using various solvents. This study examined the performance of hydrogen-donating solvents, including water, alcohols, decalin, and cyclohexane, in enhancing the oil yield while minimising the oxygen content. Supercritical water, recognised for its effective plastic degradation and chemical production capabilities, and alcohols, with their alkylating and hydrogen-donating properties, have emerged as key solvents in plastic liquefaction. The use of hydrogen donor solvents stabilizes the free radicals, enhancing the conversion of plastic waste into valuable products. In addition, this review addresses the economic efficiency of the liquefaction process.
A priori assessments of a site's biophysical and socio-economic capacity for accommodating tourism are less common than tourism impact studies. A priori evaluations can provide a contextual understanding of ecological, economic and socio-cultural forces, which shape the prospects for sustainable tourism development at the host destination, and can avert adverse impacts of tourism. We conduct an a priori assessment of the biophysical environment of Pulau Banggi, in the Malaysian state of Sabah for sustainable tourism development. We characterise baseline conditions of the island's marine biodiversity, seasonality, and infrastructure. We then evaluate how existing biophysical conditions will influence options for sustainable tourism development. In particular, we suggest conditions, if there are any, which constitute a limit to future tourism development in terms of compatibility for recreation and resilience to visitor impacts. We find that the biggest constraint is the lack of adequate water and sanitation infrastructure. Blast fishing, although occurring less than once per hour, can potentially destroy the major attraction for tourists. We conclude that while Pulau Banggi possesses natural qualities that are attractive for ecotourism, financial and institutional support must be made available to provide facilities and services that will enable local participation in environmental protection and enhance prospects for future sustainable tourism.
This study was to develop biogranules using a sequencing batch reactor (SBR) and to evaluate the effect of pineapple wastewater (PW) as a co-substrate for treating real textile wastewater (RTW). The biogranular system cycle was 24 h (2 stages of phase), with an anaerobic phase (17.8 h) followed by an aerobic phase (5.8 h) for every stage of the phase. The concentration of pineapple wastewater was the main factor studied in influencing COD and color removal efficiency. Pineapple wastewater with different concentrations (7, 5, 4, 3, and 0% v/v) makes a total volume of 3 L and causes the OLRs to vary from 2.90 to 0.23 kg COD/m3day. The system achieved 55% of average color removal and 88% of average COD removal at 7%v/v PW concentration during treatment. With the addition of PW, the removal increased significantly. The experiment on the treatment of RTW without any added nutrients proved the importance of co-substrate in dye degradation.
Palm oil mill effluent (POME) is a serious and expensive environmental problem in Malaysia. In this paper, CaFe2O4 is introduced as a novel photocatalyst for the degradation of POME under visible light irradiation. Two synthesis routes, auto-combustion and co-precipitation, and two calcination temperatures 550 °C and 700 °C were used to produce four CaFe2O4 catalysts AC550, AC700, CP550 and CP700. CP550 exhibited the greatest photocatalytic degradation at 56% chemical-oxygen-demand (COD) removal after 8 h of irradiation which dropped to 49% after three consecutive cycles indicating reasonable conversion and high recyclability. BET analysis indicated CP550 had the highest SBET (27.28 m2/g) and pore volume (0.077 cm3/g) which dropped precipitously for CP700 upon increasing the calcination temperature to an SBET of 9.73 m2/g and pore volume of 0.025 cm3/g due to annealing which created a smoother surface area as evidenced by the SEM images. UV-Vis DRS indicated CP550 had the highest band-gap (1.52 eV) which is likely due to the presence of a highly crystalline pure CaFe2O4 phase compared to the other products which existed as a mixture of Fe oxidation states evidenced by the XRD data. The PL spectra for all catalysts indicated significantly lower recombination rate for both CP550 and CP700. Introduction of IPA into the reaction mixture to eliminate hydroxyl radicals resulted in a diminishing of COD removal from 56% to 7% proving hydroxyl radicals to be the primary reactive species responsible for photodegradation of POME.
The presence of Cs(I) ions in nuclear wastewater becomes an important issue for the reason of its high toxicity. The development of adsorbent embedded metal-based catalysts that has sufficient adsorption capacity is expected for the removal of Cs(I) ions from contaminated water. This study tested the use of maghemite, titania and combined maghemite-titania polyvinyl alcohol (PVA)-alginate beads as an adsorbent to remove Cs(I) ions from aqueous solution with the variables of pH and initial concentration using batch experiments under sunlight. The results showed that the use of combined maghemite-titania PVA-alginate beads can have an efficiency of 93.1% better than the use of either maghemite PVA-alginate beads with an efficiency of 91.8% or titania PVA-alginate beads with an efficiency of 90.1%. The experimental data for adsorption of Cs(I) ions from aqueous solution with the initial concentrations of 50, 100 and 200 mg L(-1) on the surface of combined maghemite-titania PVA-alginate beads were well fit by the pseudo-second-order and Langmuir models. The optimal adsorption of Cs(I) ions from aqueous solution by combined maghemite-titania PVA-alginate beads under sunlight occurs at pH 8 with an initial Cs(I) ion concentration of 50 mg L(-1). The combined maghemite-titania PVA-alginate beads can be recycled at least five times with a slight loss of their original properties.
In this work, heterogeneous photocatalysis was used to treat pulp and paper mill effluent (PPME). Magnetically retrievable Fe2O3-TiO2 was fabricated by employing a solvent-free mechanochemical process under ambient conditions. Findings elucidated the successful incorporation of Fe2O3 into the TiO2 lattice. Fe2O3-TiO2 was found to be an irregular and slightly agglomerated surface morphology. In comparison to commercial P25, Fe2O3-TiO2 exhibited higher ferromagnetism and better catalyst properties with improvements in surface area (58.40 m2/g), pore volume (0.29 cm3/g), pore size (18.52 nm), and band gap (2.95 eV). Besides, reusability study revealed that Fe2O3-TiO2 was chemically stable and could be reused successively (five cycles) without significant changes in its photoactivity and intrinsic properties. Additionally, this study demonstrated the potential recovery of Fe2O3-TiO2 from an aqueous suspension by using an applied magnetic field or sedimentation. Interactive effects of photocatalytic conditions (initial effluent pH, Fe2O3-TiO2 dosage, and air flow-rate), reaction mechanism, and the presence of chemical oxidants (H2O2, BrO3-, and HOCl) during the treatment process of PPME were also investigated. Under optimal conditions (initial effluent pH = 3.88, [Fe2O3-TiO2] = 1.3 g/L, and air flow-rate = 2.28 L/min), the treatment efficiency of Fe2O3-TiO2 was 98.5% higher than the P25. Based on Langmuir-Hinshelwood kinetic model, apparent rate constants of Fe2O3-TiO2 and P25 were 9.2 × 10-3 and 2.7 × 10-3 min-1, respectively. The present study revealed not only the potential of using magnetic Fe2O3-TiO2 in PPME treatment but also demonstrated high reusability and easy separation of Fe2O3-TiO2 from the wastewater.
The development of eco-friendly and efficient technologies for treating wastewater is one of the attractive research area. Phytoremediation is considered to be a possible method for the removal of pollutants present in wastewater and recognized as a better green remediation technology. Nowadays the focus is to look for a sustainable approach in developing wastewater treatment capability. Water hyacinth is one of the ancient technology that has been still used in the modern era. Although, many papers in relation to wastewater treatment using water hyacinth have been published, recently removal of organic, inorganic and heavy metal have not been reviewed extensively. The main objective of this paper is to review the possibility of using water hyacinth for the removal of pollutants present in different types of wastewater. Water hyacinth is although reported to be as one of the most problematic plants worldwide due to its uncontrollable growth in water bodies but its quest for nutrient absorption has provided way for its usage in phytoremediation, along with the combination of herbicidal control, integratated biological control and watershed management controlling nutrient supply to control its growth. Moreover as a part of solving wastewater treatment problems in urban or industrial areas using this plant, a large number of useful byproducts can be developed like animal and fish feed, power plant energy (briquette), ethanol, biogas, composting and fiber board making. In focus to the future aspects of phytoremediation, the utilization of invasive plants in pollution abatement phytotechnologies can certainly assist for their sustainable management in treating waste water.
Despite being directly related to anthropogenic consumption and production, researchers have paid less attention to understanding the dynamics of non-methane volatile organic compounds. The primary objective of this research is to investigate the persistence of potential shocks to non-methane volatile organic compounds in 20 developed from 1820 to 2019 performing traditional unit root approaches and a newly developed Fourier quantile unit root test. Great portion of the empirical results obtained by traditional unit root tests reveal that the sectoral non-methane volatile organic compounds follow a non-stationary process, while the Fourier quantile unit root test indicate quite different results. The Fourier quantile test shows that non-methane volatile organic compounds are stationary in the United Kingdom, Ireland, Germany, France and Austria. In the other 15 countries, government interventions to reduce non-methane volatile organic compounds can have lasting effects and success. The inferences and policy outcomes of the empirical results are discussed in the main body of the paper.
Poor performance of wet scrubbers in rubber processing plants due to breakthrough of specific volatile organic compounds (VOCs) causes odour impact events. The performance of wet scrubbers in the rubber drying process to remove VOCs was investigated in order to determine the responsible odorants. VOC emissions originating at the inlet and outlet of wet scrubbers were quantified using gas chromatography-mass spectrometry/olfactometry (GC-MS/O). Critical VOCs were identified alongside seasonal and daily variations of those VOCs. Altogether, 80 VOCs were detected in rubber emissions with 16 classified as critical VOCs based on their chemical concentration, high odour activity value (OAV) and unpleasant odour. Volatile fatty acids (VFAs) were the dominant VOCs with seasonal variations affecting emission composition. Results demonstrated the ineffectiveness of the wet scrubbers to mitigate odorous VOCs whereas the removal of some VOCs could be improved based on their polarity and solubility. It was found that there is a correlation between the wet scrubber performance and VFAs concentration in the emissions. The findings demonstrated that combining quantitative and sensory analyses improved accuracy in identifying odorous VOCs, which can cause odour annoyance from rubber processing. A VOC identification framework was proposed using both analyses approaches.
A combination of persulfate and hydrogen peroxide (S2O8(2-)/H2O2) was used to oxidizelandfill leachate. The reaction was performed under varying S2O8(2-)/H2O2 ratio (g/g), S2O8(2-)/H2O2 dosages (g/g), pH, and reaction time (minutes), so as to determine the optimum operational conditions. Results indicated that under optimum operational conditions (i.e. 120 min of oxidation using a S2O8(2-)/H2O2 ratio of 1 g/1.47 g at a persulfate and hydrogen peroxide dosage of 5.88 g/50 ml and8.63 g/50 ml respectively, at pH 11) removal of 81% COD and 83% NH3-N was achieved. In addition, the biodegradability (BOD5/COD ratio) of the leachate was improved from 0.09 to 0.17. The results obtained from the combined use of (S2O8(2-)/H2O2) were compared with those obtained with sodium persulfate only, hydrogen peroxide only and sodium persulfate followed by hydrogen peroxide. The combined method (S2O8(2-)/H2O2) achieved higher removal efficiencies for COD and NH3-N compared with the other methods using a single oxidizing agent. Additionally, the study has proved that the combination of S2O8(2-)/H2O2 is more efficient than the sequential use of sodium persulfate followed by hydrogen peroxide in advanced oxidation processes aiming at treatingstabilizedlandfill leachate.
Effluent originating from cheese production puts pressure onto environment due to its high organic load. Therefore, the main objective of this work was to compare the influence of different process variables (transmembrane pressure (TMP), Reynolds number and feed pH) on whey protein recovery from synthetic and industrial cheese whey using polyethersulfone (PES 30 kDa) membrane in dead-end and cross-flow modes. Analysis on the fouling mechanistic model indicates that cake layer formation is dominant as compared to other pore blocking phenomena evaluated. Among the input variables, pH of whey protein solution has the biggest influence towards membrane flux and protein rejection performances. At pH 4, electrostatic attraction experienced by whey protein molecules prompted a decline in flux. Cross-flow filtration system exhibited a whey rejection value of 0.97 with an average flux of 69.40 L/m2h and at an experimental condition of 250 kPa and 8 for TMP and pH, respectively. The dynamic behavior of whey effluent flux was modeled using machine learning (ML) tool convolutional neural networks (CNN) and recursive one-step prediction scheme was utilized. Linear and non-linear correlation indicated that CNN model (R2 - 0.99) correlated well with the dynamic flux experimental data. PES 30 kDa membrane displayed a total protein rejection coefficient of 0.96 with 55% of water recovery for the industrial cheese whey effluent. Overall, these filtration studies revealed that this dynamic whey flux data studies using the CNN modeling also has a wider scope as it can be applied in sensor tuning to monitor flux online by means of enhancing whey recovery efficiency.
The black soldier fly larvae (BSFL) have been widely extolled for the application in managing various solid organic wastes. Owing to the saprophagous nature of BSFL, a rapid valorization of solid organic wastes can be accomplished with the simultaneous production of valuable biochemical compounds derived from larval biomass. In the present works, the mixed waste coconut endosperm (w-CE) and soybean curd residue (SC-r) substrates with increasing protein nutritional constituent were administered to BSFL. The correlations between protein from larval feed substrates and nutritional profiles of BSFL biomasses were ultimately unveiled. The protein from larval feed substrates could be increased by increasing of SC-r portion against w-CE. At the w-CE:SC-r ratio of 3:2, the highest larval total weight gained and growth rate were attained; indicating an optimum protein nutritional constituent in mixed organics (12.4%) that could enhance the BSFL palatability. Further increment of protein nutritional constituent in mixed organics was found acidifying the residual larval feed substrate progressively, undermining the growth of BSFL. By feeding the BSFL with optimum mixed organics, the maximum accumulations of larval lipid and protein could be achieved. Transesterification of extracted lipid had demonstrated high in monounsaturated fatty acids (73%) which was suitable for biodiesel. The BSFL palatability was finally confirmed from the bioconversion viewpoint of mixed organic wastes. Again, achieving the highest bioconversion efficiency of 14% into larval biomass after accounting the metabolic loss of 54%. Therefore, a total of 68% of mixed w-CE and SC-r could be successfully bioconverted.
Suitable extraction technique and the least cost while reducing the environmental impact is the primary concern in timber transportation planning in undulate topography. Two types of extraction machines with unique characteristics to be applied in timber harvest area in Malaysia is combined for timber harvesting with the aim each machine will extract timber suitable to their ability. A Bees Algorithm (BA) was proposed to find an optimum TTP for timber extraction, forest road, and landing locations with grid cell-sized 10 m × 10 m and attributed with fixed and variable costs. The result shows the log fisher (1351 timbers) as a preferable extraction technique with total cost of RM 86,551.73 than the crawler tractor (206 timbers); the timber extraction route is 2630 m for the log fisher and 9860 m for the crawler tractor with total cost of RM 10,453.03. The model finds a suitable timber extraction technique and estimates the extraction costs. Further studies are required to compare the BA with other optimization methods for better results.