In this study, the impact of different oxidizing agents on the structural integrity of activated carbon (AC) and multiwalled carbon nanotubes (MWCNTs) was studied for the removal of BTX from aqueous solution. Seven different combinations of green oxidizing agents (mild organic acids) in conjugation with NaOCl (basic oxidizing agent) were used. The modified adsorbents were analyzed by Brunauer, Emmett, and Teller (BET) surface area analyzer, Fourier transform infrared spectroscopy (FTIR), Boehm titration, Raman spectroscopy, thermal gravimetric analysis (TGA), x-ray diffraction (XRD), zeta potential, and variable pressure field emission scanning electron microscope (VPFESEM). The results suggested that the carbonaceous sorbents modified with combination of citric acid tartaric acid, malic acid and salicylic acid (CTMS-I) showed increased surface area (O-AC: 871.67 m2/g, O-MWCNTs: 336.37 m2/g) and total pore volume (O-AC: 0.59 cm3/g, O-MWCNTs: 0.04 cm3/g), with the significantly improved thermal stability. Preliminary batch adsorption experiments conducted using the present prepared O-AC and O-MWCNTs, showed an improved performance towards the adsorption of BTX, compared with other available reported adsorbents in the literature.
A sustainable and stable supported liquid membrane (SLM) extraction of nickel was developed via impregnation of sustainable liquid membrane in the composite membrane support consisting of polyvinylidene fluoride (PVDF) and sulfonated poly (ether ether ketone) (SPEEK). Bis-2-ethylhexyl phosphate (D2EHPA), 1-octanol, refined palm oil and sulfuric acid were employed as extractant, synergist extractant, diluent and strippant, respectively. Variables studied including effect of refined palm oil compositions as well as the configurations and thicknesses of SPEEK. Lifespan of SLM was evaluated by recycling the composite membrane support. Results revealed that upon using 100% refined palm oil, about 100% of nickel was extracted and recovered in 10 and 14 h, respectively. Composite SPEEK/PVDF stabilized SLM by reducing liquid membrane loss from 47 to 23% upon applying SPEEK at the feed side of PVDF support. High permeability and flux values were obtained at 9.26 x 10-4 cms-1 and 6.48 x 10-7 molcm-2s-1 when increasing SPEEK thickness from 0.025 to 0.055 mm, respectively. The lifespan of SLM was extended up to ninth cycles with low weight loss percentage of the impregnated composite membrane (8%). In conclusion, the SPEEK/PVDF impregnated with refined palm oil has improved the stability of SLM extraction of nickel ions from industrial wastewater.
The fast pyrolysis of waste lignin derived from biobutanol production process was performed to determine the optimal pyrolysis conditions and pyrolysis product properties. Four types of pyrolysis reactors, e.g.: micro-scale pyrolyzer-gas chromatography/mass spectrometry, lab and bench scale fixed bed (FB) reactors, and bench scale rotary kiln (RK) reactor, were employed to compare the pyrolysis reaction conditions and product properties obtained from different reactors. The yields of char, oil, and gas obtained from lab scale and bench scale reactor were almost similar compared to FB reactor. RK reactor produced desirable bio-oil with much reduced yield of poly aromatic hydrocarbons (cancer precursor) due to its higher cracking reaction efficiency. In addition, char agglomeration and foaming of lignin pyrolysis were greatly restricted by using RK reactor compared to the FB reactor.
In this study, a binary mixture of petroleum coke and palm kernel shell had been investigated as potential starting materials for activated carbon production. Single-stage potassium carbonate (K2CO3) activation under nitrogen (N2) atmosphere was adopted in this research study. Effect of several operating parameters that included the impregnation ratio (1-3 wt./wt.), activation temperature (600-800 °C), and dwell time (1-2 hrs) were analyzed by using the Box-Behnken experimental design. Influence of these parameters towards activated carbon yield (Y1) and carbon dioxide (CO2) adsorption capacity at an atmospheric condition (Y2) were investigated. The optimum conditions for the activated carbon production were attained at impregnation ratio of 1.75:1, activation temperature of 680 °C, and dwell time of 1 h, with its corresponding Y1 and Y2 is 56.2 wt.% and 2.3991 mmol/g, respectively. Physicochemical properties of the pristine materials and synthesized activated carbon at the optimum conditions were analyzed in terms of their decomposition behavior, surface morphology, elemental composition, and textural characteristics. The study revealed that the blend of petroleum coke and palm kernel shell can be effectively used as the activated carbon precursors, and the experimental findings demonstrated comparable CO2 adsorption performance with commercial activated carbon as well as that in literatures.
Biochar (BC) has attracted much attention owing to its superior sorption capacity towards ionized organic contaminants. However, the mechanism of ionized organics sorption occurring within BC containing large amounts of minerals is still controversial. In this study, we demonstrate the physicochemical structure of high-salinity microalgal residue derived biochar (HSBC) and elucidate the corresponding sorption mechanisms for four ionized dyes along with determining the crucial role of involved minerals. The results indicate that sodium and calcium minerals mainly exist within HSBCs, and the pyrolysis temperature can dramatically regulate the phases and interfacial property of both carbon matrix and minerals. As a result, the HSBC shows a higher sorption potential, benefiting from abundant functional groups and high content of inorganic minerals. Using theoretical calculations, the activities of electron donor-acceptor interaction between HSBCs and different dyes are clearly illustrated, thereby identifying the critical role of Ca2+ in enhancing the removal of ionized dyes in HSBCs. In addition, Ca-containing minerals facilitate the sorption of ionized dyes in HSBCs by forming ternary complexes through metal-bridging mechanism. These results of mineral-induced dye sorption mechanisms help to better understand the sorption of ionized organics in high-salt containing BC and provide a new disposal strategy for hazardous microalgal residue, as well as provide a breakthrough in making the remediation of ionized organic contaminated microalgal residue derived absorbent feasible.
Indoor air pollution with toxic volatile organic compounds (VOCs) and fine particulate matter (PM2.5) is a threat to human health, causing cancer, leukemia, fetal malformation, and abortion. Therefore, the development of technologies to mitigate indoor air pollution is important to avoid adverse effects. Adsorption and photocatalytic oxidation are the current approaches for the removal of VOCs and PM2.5 with high efficiency. In this review we focus on the recent development of indoor air pollution mitigation materials based on adsorption and photocatalytic decomposition. First, we review on the primary indoor air pollutants including formaldehyde, benzene compounds, PM2.5, flame retardants, and plasticizer: Next, the recent advances in the use of adsorption materials including traditional biochar and MOF (metal-organic frameworks) as the new emerging porous materials for VOCs absorption is reviewed. We review the mechanism for mitigation of VOCs using biochar (noncarbonized organic matter partition and adsorption) and MOF together with parameters that affect indoor air pollution removal efficiency based on current mitigation approaches including the mitigation of VOCs using photocatalytic oxidation. Finally, we bring forward perspectives and directions for the development of indoor air mitigation technologies.
Effective regulation of p-phenylenediamine (PPD), a widely used precursor of hair dye that is harmful to human health in large concentration, relies upon an accurate yet simple detection of PPD. In this context, amperometric electrode sensor based on perovskite oxide becomes attractive given its portability, low cost, high sensitivity, and rapid processing time. This work reports the systematic characterization of a series of Sr-doped PrCoO3-δ perovskite oxides with composition of Pr1-xSrxCoO3-δ(x = 0, 0.2, 0.4, 0.6, 0.8, and 1) for PPD detection in an alkaline solution. PSC82 deposited onto glassy carbon electrode (PSC82/GCE) generates the highest redox currents which correlates with the highest hydrogen peroxide intermediates (HO2-) yield and the σ*-orbital (eg) filling of Co that is closest to unity for PSC82. PSC82/GCE provides the highest sensitivities of 655 and 308 μA mM-1 cm-2 in PPD concentration range of 0.5-2,900 and 2,900-10,400 μM, respectively, with a limit of detection of 0.17 μM. PSC82/GCE additionally demonstrates high selectivity to PPD and long term stability during 50 consecutive cyclic voltammetry scans and over 1-month storage period. The potential applicability of PSC82/GCE was also demonstrated by confirming the presence of very low concentration of PPD of below 0.5% in real hair dyes.
The removal of antibiotics and resistance genes in wastewater treatment plants has attracted widespread attention, but the potential role of residual antibiotics in the disposal of waste activated sludge (WAS) has not been clearly understood. In this study, the effect of roxithromycin (ROX) on volatile fatty acid (VFA) recovery from WAS anaerobic fermentation was investigated. The experimental results showed that ROX made a positive contribution to the production of VFAs. With the increase of ROX dosages from 0 to 100 mg/kg TSS, the maximum accumulation of VFAs increased from 295 to 610 mg COD/L. Mechanism studies revealed that ROX promoted the solubilization of WAS by facilitating the disruption of extracellular polymeric substances. In addition, ROX enhanced the activity of acetate kinase and inhibited the activities of α-glucosidase and coenzyme F420, and showed a stronger inhibitory effect on methane production than the hydrolysis process, thus resulting in an increase in VFA accumulation. These findings provide a new insight for the role of antibiotics in anaerobic fermentation of WAS.
Antibiotics and pharmaceuticals related products are used to enhance public health and quality of life. The wastewater that is produced from pharmaceutical industries still contains noticeable amount of antibiotics, and this has remained one of the major environmental problems facing public health. The conventional wastewater remediation approach employed by the pharmaceutical industries for the antibiotics wastewater removal is unable to remove the antibiotics completely. Besides, municipal and livestock wastewater also contain unmetabolized antibiotics released by human and animal, respectively. The antibiotic found in wastewater leads to antibiotic resistance challenges, also emergence of superbugs. Currently, numerous technological approaches have been developed to remove antibiotics from the wastewater. Therefore, it was imperative to critically review the weakness and strength of these current advanced technological approaches in use. Besides, the conventional methods for removal of antibiotics such as Klavaroti et al., Homem and Santos also discussed. Although, membrane treatment is discovered as the ultimate choice of approach, to completely remove the antibiotics, while the filtered antibiotics are still retained on the membrane. This study found, hybrid processes to be the best solution antibiotics removal from wastewater. Nevertheless, real-time monitoring system is also recommended to ascertain that, wastewater is cleared of antibiotics.
Pollution with pesticides is a widespread global problem and biomonitoring of the environment and human populations is necessary to assess potential harmful biological effects. One of the pesticides that are showing up in vegetables and fruit is chlorpyrifos (CPS). CPS is a nerve-poisoning organophosphorus insecticide, which is in up to 1/3 of all conventionally produced citrus fruits. Our review shows that CPS is a hazardous material that poses risks to human health and also pollutes the environment. There is numerous risk assessment of CPS reported, however, the assessment is easily affected by factors such as climate change, exposure period and CPS concentration. Therefore, rigorous update of the hazardous level of CPS is needed to determine the threshold level safe for humans and animals. There is a need for remediation using for example photoreactive nanoparticle methods and microbial degeneration possessing high degradation efficiency (73-97%). In addition, stringent biomonitoring of food, environment and human exposure should occur to avoid exposure to chemicals via citrus fruits and vegetables. This is necessary to assess health risks and socioeconomic impacts which also require collaboration between private and public sectors to facilitate the growth, sale and manufacturing of biopesticides.
Nowadays, increasing the risk for copper leaching into the drinking water in homes, hotels and schools has become unresolved issues all around the countries such as Canada, the United States, and Malaysia. The leaching of copper in tap water is due to a combination of acidic water, damaged pipes, and corroded plumbing fixtures. To remedy this global problem, a triple interconnected structure of CdS/Au/GQDs was designed as a photo-to-electron conversion medium for a real time and selective visible-light-prompt photoelectrochemical (PEC) sensor for Cu2+ ions in real water samples. The synergistic interaction of the CdS/Au/GQDs enabled the smooth transportation of charge carriers to the charge collector and provided a channel to inhibit the charge recombination reaction. Thus, a detection limit of 2.27 nM was obtained, which is 10,000 fold lower than that of WHO's Guidelines for Drinking-water Quality (∼30 μM). The photocurrent reduction was negligible after 30 days of storage under ambient conditions, suggesting the high stability of photoelectrode. Moreover, the real-time monitoring of Cu2+ ions in real samples was performed with satisfactory results, confirming the capability of the investigated photoelectrode as the most practical detector for trace amounts of Cu2+ ions.
Improving the sustainability and cost-effectiveness of biochar production is crucial to meet increased global market demand. Here, we developed a single-step microwave steam activation (STMSA) as a simplified yet efficient method to produce microwave activated biochar (MAB) from waste palm shell (WPS). The STMSA recorded a higher heating rate (70 °C/min) and higher conversion (45 wt%) of WPS into highly microporous MAB (micropore surface area of 679.22 m2/g) in contrast with the conventional heating approach (≤ 12-17 wt%). The MAB was then applied as biosorbent for hazardous landfill leachate (LL) treatment and the adsorption performance was compared with commercial activated carbon under different pH, adsorbent quantity, adsorbate concentrations, and contact times. The MAB demonstrated high adsorption capacity, achieving maximum adsorption efficiency at 595 mg/g and 65 % removal of chemical oxygen demand (COD) with 0.4 g/L of adsorbent amount under optimal acidic conditions (pH ≈ 2-3) after 24 h of contact time. The Freundlich isotherm and pseudo second-order kinetic models were well-fitted to explain the equilibrium adsorption and kinetics. The results indicate the viability of STMSA as a fast and efficient approach to produce activated biochar as a biosorbent for the treatment of hazardous landfill leachate.
In this research, biomass from oil palm empty fruit bunch was used as the carbon precursor and sulfonated by 4-benzenediazonium sulfonate (4-BDS) to produce solid acid catalyst. The as-synthesized catalysts were characterized and the performances were tested in esterification of palm fatty acid distillate (PFAD) for biodiesel production. Scanning Electron Microscopy (SEM) showed that clear porous and rough carbon surface was successfully developed after calcination which favored the attachment of sulfonic groups. Thermogravimetric Analysis (TGA) result showed that the catalyst was thermally stable up to 600 °C. Fourier Transform Infrared Spectroscopy (FTIR) proved that SO and SO3H sulfonic groups were successfully attached to the carbon catalyst. From the catalytic activity tests, the results showed that the catalyst which was calcined at 200 °C and sulfonated with 15:1 sulfanilic acid to AC ratio was the optimum catalyst as it provided the highest biodiesel yield. Further investigation showed that the reaction time of 7 h and 20 wt.% of catalyst loading were reported as optimum esterification conditions which provided the highest biodiesel yield at 98.1 %.
Charcoal production activities at the Matang Mangrove Forest Reserve (MMFR) in Peninsular Malaysia have a potential to emit volatile compounds such as Hg back into the ambient environment, raising concerns on the public health and safety. The present study was aimed at analyzing Hg concentration from different plant/animal tissues and sediment samples (in total 786 samples) to understand clearly the Hg distribution at the MMFR. Leaves of Rhizophora spp. showed higher Hg concentration with an increasing trend from young, to mature, to senescent and decomposing stages, which was possibly due to accumulation of Hg over time. The low Hg concentration in Rhizophora roots and bark suggests a limited absorption from the sediments and a meagre accumulation/partitioning by the plant tissue, respectively. In the case of mangrove cockles the concentration of Hg was lower than the permissible limits for seafood consumption. Although the mangrove gastropod - Cassidula aurisfelis Bruguière had rather elevated Hg in the muscle tissue, it is still less than the environmental safely limit. Beside the chances of atmospheric deposition for Hg, the sediment samples were found to be unpolluted in nature, indicating that in general the MMFR is still safe in terms of Hg pollution.
Environmental hazards, industrial, and municipal wastes geochemical and geophysical assessments were carried out at an industrial waste disposal (IWD) site at Bukit Kepong, Kuala Lumpur, Malaysia. RES2-D geophysical method was applied, capable of identification and quantification of the industrial wastes; buried hazardous materials (BHM) and their effects on the subsurface stratum, from the moderately saturated zones, to fully saturated zones housing the aquifer units underneath the water table. Six RES2-D survey profiles were respectively acquired along E-W, and N-S directions. The perpendicular arrangement of the RES2-D survey lines, was tenaciously designed to make possible, the industrial waste materials (IWM)and municipal solid waste (MSW) quantification, with sufficient length of survey lines set at 200 m, and electrode spacing of 5 m, to cover as much details segments of the IWM and MSW as possible. The six RES2-D inversion results, helped in the subsurface stratum classification into three layers, namely; soft layers, which encompasses the waste materials, with varied resistivity values i.e., 0-100 Ω-m, at 10-15 m depths. The consolidated layers produced varied resistivity values i.e., 101-400 Ω-m, at 15-20 m depths. The bedrock has the highest resistivity values i.e., 401-2000 Ω-m, at depths > 20 m. The estimated volume of the waste materials was 312,000 m 3, using 3-D Oasis Montaj modeling via rectangular prism model generated from the inverted RES2-D. Results from the geochemical analysis helped in the validation of the site as a potential contaminated zone with severe health effects.
This study was set up to model and optimize the performance and emission characteristics of a diesel engine fueled with carbon nanoparticle-dosed water/diesel emulsion fuel using a combination of soft computing techniques. Adaptive neuro-fuzzy inference system tuned by particle swarm algorithm was used for modeling the performance and emission parameters of the engine, while optimization of the engine operating parameters and the fuel composition was conducted via multiple-objective particle swarm algorithm. The model input variables were: injection timing (35-41° CA BTDC), engine load (0-100%), nanoparticle dosage (0-150 μM), and water content (0-3 wt%). The model output variables included: brake specific fuel consumption, brake thermal efficiency, as well as carbon monoxide, carbon dioxide, nitrogen oxides, and unburned hydrocarbons emission concentrations. The training and testing of the modeling system were performed on the basis of 60 data patterns obtained from the experimental trials. The effects of input variables on the performance and emission characteristics of the engine were thoroughly analyzed and comprehensively discussed as well. According to the experimental results, injection timing and engine load could significantly affect all the investigated performance and emission parameters. Water and nanoparticle addition to diesel could markedly affect some performance and emission parameters. The modeling system could predict the output parameters with an R2 > 0.93, MSE
Given the safety issues associated with flammability characteristics of alternative environmentally-friendly refrigerants, it is vital to establish measurement systems to accurately analyse the flammability of these mildly flammable refrigerants. In this study, we used a customised Hartmann bomb analogue to measure the minimum ignition energy (MIE) and laminar burning velocity (BV) for refrigerant/air mixtures of pure ammonia (R717), R32, R1234yf and mixtures of R32 and R1234yf with non-flammable refrigerants of R134a, R125 and carbon dioxide (R744). The MIEs of R717, R32, and R1234yf were measured at an ambient temperature of 24 °C to be (18.0 ± 1.4), (8.0 ± 1.5) and (510 ± 130) mJ at equivalence ratios of 0.9, 1.27 and 1.33, respectively. Adding the non-flammable refrigerants R134a, R125 and R744 along with R32 at volumetric concentrations of 5% each to R1234yf reduced the latter compound's flammability and increased its MIE by one order of magnitude. The laminar burning velocities of pure R717 and R32 were measured at an equivalence ratio of 1.1 using the flat flame method and found to be 8.4 and 7.4 cm/s, respectively. Adding 5% R1234yf to R32 decreased the laminar burning velocity by 11%, while a further 5% addition of R1234yf resulted in a decrease of over 30% in the laminar burning velocity.
River systems in developing and emerging countries are often fragmented relative to land and waste management in their catchment. The impact of inconsistent waste management and releases is a major challenge in water quality management. To examine how anthropogenic activities and estuarine effects impact water quality, we characterised water conditions, in-situ microbiomes, profiles of faecal pollution indicator, pathogenic and antibiotic resistant bacteria in the River Melayu, Southern Malaysia. Overall, upstream sampling locations were distinguished from those closer to the coastline by physicochemical parameters and bacterial communities. The abundances of bacterial DNA, total E. coli marker genes, culturable bacteria as well as antibiotic resistance ESBL-producing bacteria were elevated at upstream sampling locations especially near discharge of a wastewater oxidation pond. Furthermore, 85.7% of E. faecalis was multidrug-resistant (MDR), whereas 100% of E. cloacae, E. coli, K. pneumoniae were MDR. Overall, this work demonstrates how pollution in river estuaries does not monotonically change from inland towards the coast but varies according to local waste releases and tidal mixing. We also show that surrogate markers, such dissolved oxygen, Bacteroides and Prevotella abundances, and the rodA qPCR assay for total E. coli, can identify locations on a river that deserve immediate attention to mitigate AMR spread through improved waste management.
Powdered-photocatalysis of organic wastewater is widely investigated, unfortunately not industrially implemented due to its high energy requirement. Interestingly, such issue may be alleviated via the elimination of mechanical stirring required. Core-shell ZnO-based photocatalysts were developed herein, subsequently demonstrated efficient photocatalytic activities in the absence of mechanical stirring. Results show that the developed SiO2-cored ZnO photocatalyst are highly crystalline, while significantly smaller than coreless, pure ZnO due to the multi-point crystallization prompted. Additionally, it is also inherited with considerable buoyancy ability from SiO2-core in the absence of mechanical stirring, concurrently rendered with UV-active properties due to its ZnO-shell. Experimentally, 55% of particles of ZnO_0.0025 (0.0025 mol of ZnO-deposition) were found stably suspended for 60 min in liquid substrate, as opposed to the instant-settling of pure ZnO particles. In term of photocatalytic activity, ZnO_0.01 manifested the best methylene blue (MB) degradation with 150 mL/min of O2-bubbling. 67.63% of MB was degraded with photocatalyst loading of 0.2 g/L after 120 min UV-irradiation, simultaneously recorded the highest pseudo-first order reaction constant of 9.636 × 10-3 min-1. As summary, the auto-suspending photocatalysis conceptualized in current study offers a high possibility in reducing energy requirement for photo-treatment of wastewater, hence advocating its industrialization potential in near future.
The presence of pharmaceuticals and endocrine-disrupting compounds in aquatic systems is a matter of great concern. The occurrence, fate, and potential toxicity of these compounds have triggered the interest of the scientific community. As a result of their high solubility and low volatility, they are common in aquatic systems, and wastewater treatment plants (WWTP) are the main reservoir for these contaminants. Conventional WWTPs have demonstrated an inability to remove these contaminants completely; hence, different advanced treatment processes have been explored to compensate for the lapses of the conventional system. The outcome of this study revealed the significant improvements made using advanced treatment processes to diminish the number of contaminants; however, some contaminants have proven to be refractory. Thus, there is a need to modify various advanced treatment processes or employ additional treatment processes. Polymer inclusion membranes (PIMs) are a liquid membrane technology that is highly efficient at removing contaminants from water. They have been widely studied for the removal of heavy metals and nutrients from aquatic systems; however, only a few studies have investigated the use of PIMs to remove pharmaceutically active compounds from aquatic systems. This research aims to raise awareness on the application of PIMs as a promising water treatment technology which has a great potential for the remediation of pharmaceuticals and endocrine disruptors in the aquatic system, due to its versatility, ease/low cost of preparation and high contaminant selectivity.