MyMedR

Displaying all 5 publications

Abstract:

Sort:

Fulltext A Solar Panel-Integrated Modified Planner Inverted F Antenna for Low Earth Orbit Remote Sensing Nanosatellite Communication System

Alam T, Islam MT, Ullah MA, Cho M

Sensors (Basel), 2018 Jul 31;18(8).
PMID: 30065233 DOI: 10.3390/s18082480

One of the most efficient methods to observe the impact of geographical, environmental, and geological changes is remote sensing. Nowadays, nanosatellites are being used to observe climate change using remote sensing technology. Communication between a remote sensing nanosatellite and Earth significantly depends upon antenna systems. Body-mounted solar panels are the main source of satellite operating power unless deployable solar panels are used. Lower ultra-high frequency (UHF) nanosatellite antenna design is a crucial challenge due to the physical size constraint and the need for solar panel integration. Moreover, nanosatellite space missions are vulnerable because of antenna and solar panel deployment complexity. This paper proposes a solar panel-integrated modified planner inverted F antenna (PIFA) to mitigate these crucial limitations. The antenna consists of a slotted rectangular radiating patch with coaxial probe feeding and a rectangular ground plane. The proposed antenna has achieved a -10 dB impedance bandwidth of 6.0 MHz (447.5 MHz⁻453.5 MHz) with a small-sized (80 mm× 90 mm× 0.5 mm) radiating element. In addition, the antenna achieved a maximum realized gain of 0.6 dB and a total efficiency of 67.45% with the nanosatellite structure and a solar panel. The challenges addressed by the proposed antenna are to ensure solar panel placement between the radiating element and the ground plane, and provide approximately 55% open space to allow solar irradiance into the solar panel.
Fulltext Paper-Based Flexible Antenna for Wearable Telemedicine Applications at 2.4 GHz ISM Band

Ullah MA, Islam MT, Alam T, Ashraf FB

Sensors (Basel), 2018 Dec 01;18(12).
PMID: 30513719 DOI: 10.3390/s18124214

This paper demonstrates the performance of a potential design of a paper substrate-based flexible antenna for intrabody telemedicine systems in the 2.4 GHz industrial, scientific, and medical radio (ISM) bands. The antenna was fabricated using 0.54 mm thick flexible photo paper and 0.03 mm copper strips as radiating elements. Design and performance analyses of the antenna were performed using Computer Simulation Technology (CST) Microwave Studio software. The antenna performances were investigated based on the reflection coefficient in normal and bent conditions. The total dimensions of the proposed antenna are 40 × 35 × 0.6 mm³. The antenna operates at 2.33⁻2.53 GHz in the normal condition. More than an 8% fractional bandwidth is expressed by the antenna. Computational analysis was performed at different flexible curvatures by bending the antenna. The minimum fractional bandwidth deviation is 5.04% and the maximum is 24.97%. Moreover, it was mounted on a homogeneous phantom muscle and a four-layer human tissue phantom. Up to a 70% radiation efficiency with a 2 dB gain was achieved by the antenna. Finally, the performance of the antenna with a homogeneous phantom muscle was measured and found reliable for wearable telemedicine applications.
Fulltext Microwave Imaging Sensor Using Low Profile Modified Stacked Type Planar Inverted F Antenna

Islam MT, Ullah MA, Alam T, Singh MJ, Cho M

Sensors (Basel), 2018 Sep 05;18(9).
PMID: 30189632 DOI: 10.3390/s18092949

Microwave imaging is the technique to identify hidden objects from structures using electromagnetic waves that can be applied in medical diagnosis. The change of dielectric property can be detected using microwave antenna sensor, which can lead to localization of abnormality in the human body. This paper presents a stacked type modified Planar Inverted F Antenna (PIFA) as microwave imaging sensor. Design and performance analysis of the sensor antenna along with computational and experimental analysis to identify concealed object has been investigated in this study. The dimension of the modified PIFA radiating patch is 40 × 20 × 10 mm³. The reflector walls used, are 45 mm in length and 0.2-mm-thick inexpensive copper sheet is considered for the simulation and fabrication which addresses the problems of high expenses in conventional patch antenna. The proposed antenna sensor operates at 1.55⁻1.68 GHz where the maximum realized gain is 4.5 dB with consistent unidirectional radiation characteristics. The proposed sensor antenna is used to identify tumor in a computational human tissue phantom based on reflection and transmission coefficient. Finally, an experiment has been performed to verify the antenna's potentiality of detecting abnormality in realistic breast phantom.
Fulltext Design and compatibility analysis of a solar panel integrated UHF antenna for nanosatellite space mission

Alam T, Islam MT, Ullah MA, Rahmatillah R, Aheieva K, Lap CC, et al.

PLoS One, 2018;13(11):e0205587.
PMID: 30427842 DOI: 10.1371/journal.pone.0205587

A compact UHF antenna has been presented in this paper for nanosatellite space mission. A square ground plane with slotted rectangular radiating element have been used. Coaxial probe feeding is used to excite. The rectangular slot of the radiating patch is responsible for resonating at lower UHF bands. One of the square faces of the nanosatellite structure works as the ground plane for the slotted radiating element. The fabricated prototype of the proposed antenna has achieved an impedance bandwidth (S11< -10dB) of 7.0 MHz (398 MHz- 405 MHz) with small size of 97 mm× 90 mm radiating element. The overall ground plane size is 100 mm × 100 mm × 0.5 mm. The proposed antenna has achieved a gain of 1.18 dB with total efficiency of 62.5%. The proposed antenna addresses two design challenges of nanosatellite antenna, (a) assurance of the placement of solar panel beneath the radiating element; (b) providing about 50% open space for solar irradiance to pass onto the solar panel, enabling the solar panel to achieve up to 93.95% of power under of normal conditions.
Overexpression of rice High-affinity Potassium Transporter gene OsHKT1;5 improves salinity and drought tolerance in Arabidopsis

Ullah MA, Abdullah-Zawawi MR, Razalli II, Sukiran NL, Uddin MI, Zainal Z

Mol Biol Rep, 2024 Dec 07;52(1):40.
PMID: 39644345 DOI: 10.1007/s11033-024-10130-6

BACKGROUND: Rice is subjected to various environmental stresses, resulting in significant production losses. Abiotic stresses, particularly drought and salinity, are the leading causes of plant damage worldwide. The High-affinity Potassium Transporter (HKT) gene family plays an important role in enhancing crop stress tolerance by regulating physiological and enzymatic functions.
METHODS AND RESULTS: This study investigates the effect of overexpressing the rice HKT1;5 gene in Arabidopsis thaliana on its tolerance to salinity and drought. The OsHKT1;5 gene was introduced into Arabidopsis under the control of 35 S promoter of CaMV via floral dip transformation method. PCR confirmed the integration of the transgene into the Arabidopsis genome, while qPCR analysis showed its expression. Three transgenic lines of OsHKT1;5 were used for stress treatment and phenotypic studies. The overexpressed lines showed considerably higher germination rates, increased leaf counts, greater fresh and dry weights of the roots and shoots, higher chlorophyll contents, longer root lengths, and reduced Na+ levels together with increased K+ ions levels after salt and drought treatments, in comparison to wild-type plants. Furthermore, overexpressed lines exhibited higher antioxidant levels than wild-type plants under salinity and drought conditions. In addition, transgenic lines showed higher expression levels of the OsHKT1;5 gene in both roots and shoots compared to wild-type plants.
CONCLUSIONS: In conclusion, this study revealed OsHKT1;5 as a promising candidate for enhancing tolerance to salinity and drought stresses in rice, marking a significant step toward developing a new rice variety with improved abiotic stress tolerance.