The use of solar energy is one of the most prominent strategies for addressing the present energy management challenges. Solar energy is used in numerous residential sectors through flat plate solar collectors. The thermal efficiency of flat plate solar collectors is improved when conventional heat transfer fluids are replaced with nanofluids because they offer superior thermo-physical properties to conventional heat transfer fluids. Concentrated chemicals are utilized in nanofluids' conventional synthesis techniques, which produce hazardous toxic bi-products. The present research investigates the effects of novel green covalently functionalized gallic acid-treated multiwall carbon nanotubes-water nanofluid on the performance of flat plate solar collectors. GAMWCNTs are highly stable in the base fluid, according to stability analysis techniques, including ultraviolet-visible spectroscopy and zeta potential. Experimental evaluation shows that the thermo-physical properties of nanofluid are better than those of base fluid deionized water. The energy, exergy and economic analysis are performed using 0.025%, 0.065% and 0.1% weight concentrations of GAMWCNT-water at varying mass flow rates 0.010, 0.0144, 0.0188 kg/s. The introduction of GAMWCNT nanofluid enhanced the thermal performance of flat plate solar collectors in terms of energy and exergy efficiency. There is an enhancement in efficiency with the rise in heat flux, mass flow rate and weight concentration, but a decline is seen as inlet temperature increases. As per experimental findings, the highest improvement in energy efficiency is 30.88% for a 0.1% weight concentration of GAMWCNT nanofluid at 0.0188 kg/s compared to the base fluid. The collector's exergy efficiency increases with the rise in weight concentration while it decreases with an increase in flow rate. The highest exergy efficiency is achieved at 0.1% GAMWCNT concentration and 0.010 kg/s mass flow rate. GAMWCNT nanofluids have higher values for friction factor compared to the base fluid. There is a small increment in relative pumping power with increasing weight concentration of nanofluid. Performance index values of more than 1 are achieved for all GAMWCNT concentrations. When the solar thermal collector is operated at 0.0188 kg/s and 0.1% weight concentration of GAMWCNT nanofluid, the highest size reduction, 27.59%, is achieved as compared to a flat plate solar collector with water as a heat transfer fluid.
ABSTRACT: A total of 133 samples of whole wheat and barley grains and wheat and barley flour collected from retail markets in the main cities of Punjab, Pakistan, were analyzed for the mycotoxin fumonisin B1 (FB1) using reverse phase high-performance liquid chromatography with fluorescence detection. Of these samples, 120 (90%) were positive for FB1, and 75 (63%) of the 120 positive samples had FB1 concentrations higher than the European Union maximum (200 μg/kg). The limit of detection was 4 μg/kg. The highest mean (±SD) concentration of FB1 was found in whole wheat samples, 980.5 ± 211.4 μg/kg. The calculated dietary intakes of FB1 from wheat and barley flours were 4,456 and 503.7 ng/g of body weight per day, respectively.
A new micro heat exchanger was analyzed using numerical formulation of conjugate heat transfer for single-phase fluid flow across copper microchannels. The flow across bent channels harnesses asymmetric laminar flow and dean vortices phenomena for heat transfer enhancement. The single-channel analysis was performed to select the bent channel aspect ratio by varying width and height between 35-300 μm for Reynolds number and base temperature magnitude range of 100-1000 and 320-370 K, respectively. The bent channel results demonstrate dean vortices phenomenon at the bend for Reynolds number of 500 and above. Thermal performance factor analysis shows an increase of 18% in comparison to straight channels of 200 μm width and height. Alumina nanoparticles at 1% and 3% concentration enhance the Nusselt number by an average of 10.4% and 23.7%, respectively, whereas zirconia enhances Nusselt number by 16% and 33.9% for same concentrations. On the other hand, thermal performance factor analysis shows a significant increase in pressure drop at high Reynolds number with 3% particle concentration. Using zirconia for nanofluid, Nusselt number of the bent multi-channel model is improved by an average of 18% for a 3% particle concentration as compared to bent channel with deionized water.
Vertical axis wind turbines (VAWT) are a source of renewable energy and are used for both industrial and domestic purposes. The study of noise characteristics of a VAWT is an important performance parameter for the turbine. This study focuses on the development of a linear microphone array and measuring acoustic signals on a cambered five-bladed 45 W VAWT in an anechoic chamber at different tip speed ratios. The sound pressure level spectrum of VAWT shows that tonal noises such as blade passing frequencies dominate at lower frequencies whereas broadband noise corresponds to all audible ranges of frequencies. This study shows that the major portion of noise from the source is dominated by aerodynamic noises generated due to vortex generation and trailing edge serrations. The research also predicts that dynamic stall is evident in the lower Tip speed ratio (TSR) region making smaller TSR values unsuitable for a quiet VAWT. This paper compares the results of linear aeroacoustic array with a 128-MEMS acoustic camera with higher resolution. The study depicts a 3 dB margin between two systems at lower TSR values. The research approves the usage of the 8 mic linear array for small radius rotary machinery considering the results comparison with a NORSONIC camera and its resolution. These observations serve as a basis for noise reduction and blade optimization techniques.
Covid-19 has given one positive perspective to look at our planet earth in terms of reducing the air and noise pollution thus improving the environmental conditions globally. This positive outcome of pandemic has given the indication that the future of energy belong to green energy and one of the emerging source of green energy is Lithium-ion batteries (LIBs). LIBs are the backbone of the electric vehicles but there are some major issues faced by the them like poor thermal performance, thermal runaway, fire hazards and faster rate of discharge under low and high temperature environment,. Therefore to overcome these problems most of the researchers have come up with new methods of controlling and maintaining the overall thermal performance of the LIBs. The present review paper mainly is focused on optimization of thermal and structural design parameters of the LIBs under different BTMSs. The optimized BTMS generally demonstrated in this paper are maximum temperature of battery cell, battery pack or battery module, temperature uniformity, maximum or average temperature difference, inlet temperature of coolant, flow velocity, and pressure drop. Whereas the major structural design optimization parameters highlighted in this paper are type of flow channel, number of channels, length of channel, diameter of channel, cell to cell spacing, inlet and outlet plenum angle and arrangement of channels. These optimized parameters investigated under different BTMS heads such as air, PCM (phase change material), mini-channel, heat pipe, and water cooling are reported profoundly in this review article. The data are categorized and the results of the recent studies are summarized for each method. Critical review on use of various optimization algorithms (like ant colony, genetic, particle swarm, response surface, NSGA-II, etc.) for design parameter optimization are presented and categorized for different BTMS to boost their objectives. The single objective optimization techniques helps in obtaining the optimal value of important design parameters related to the thermal performance of battery cooling systems. Finally, multi-objective optimization technique is also discussed to get an idea of how to get the trade-off between the various conflicting parameters of interest such as energy, cost, pressure drop, size, arrangement, etc. which is related to minimization and thermal efficiency/performance of the battery system related to maximization. This review will be very helpful for researchers working with an objective of improving the thermal performance and life span of the LIBs.