Strain localization is a significant issue that poses interesting research challenges in viscoelastic materials because it is difficult to accurately predict the damage evolution behavior. Over time, the damage mechanism in the amorphous structure of viscoelastic materials leads to subsequent localization into a shear band, gradually jeopardizing the materials' elastic sustainability. The primary goal of this study is to further understand the morphological effects and the role of shear bands in viscoelastic materials precipitated by strain localization. The current study aims to consolidate the various failure mechanisms of a sample and its geometry (surface-to-volume ratio) used in torsional testing, as well as to understand their effects on stress relaxation durability performance. A torsional shear load stress relaxation durability test was performed within the elastic region on an isotropic viscoelastic sample made of silicon rubber and a 70% weight fraction of micron-sized carbonyl iron particles. Degradation was caused by a shear band of localized plasticity that developed microscopically due to stress relaxation durability. The failure pattern deteriorated as the surface-to-volume ratio decreased. A field-emission scanning electron microscope (FESEM) and a tapping-mode atomic force microscope (AFM) were used for further observation and investigation of the sample. After at least 7500 cycles of continuous shearing, the elastic sustainability of the viscoelastic materials microstructurally degraded, as indicated by a decline in stress performance over time. Factors influencing the formation of shear bands were observed in postmortem, which was affected by simple micromanipulation of the sample geometry, making it applicable for practical implementation to accommodate any desired performance and micromechanical design applications.
The widespread use of magnetorheological elastomer (MRE) materials in various applications has yet to be limited due to the fact that there are substantial deficiencies in current experimental and theoretical research on its microstructural durability behavior. In this study, MRE composed of silicon rubber (SR) and 70 wt% of micron-sized carbonyl iron particles (CIP) was prepared and subjected to stress relaxation evaluation by torsional shear load. The microstructure and particle distribution of the obtained MRE was evaluated by a field emission scanning electron microscopy (FESEM). The influence of constant low strain at 0.01% is the continuing concern within the linear viscoelastic (LVE) region of MRE. Stress relaxation plays a significant role in the life cycle of MRE and revealed that storage modulus was reduced by 8.7%, normal force has weakened by 27%, and stress performance was reduced by 6.88% along approximately 84,000 s test duration time. This time scale was the longest ever reported being undertaken in the MRE stress relaxation study. Novel micro-mechanisms that responsible for the depleted performance of MRE was obtained by microstructurally observation using FESEM and in-phase mode of atomic force microscope (AFM). Attempts have been made to correlate strain localization produced by stress relaxation, with molecular deformation in MRE amorphous matrix. Exceptional attention was focused on the development of molecular slippage, disentanglement, microplasticity, microphase separation, and shear bands. The relation between these microstructural phenomena and the viscoelastic properties of MRE was diffusely defined and discussed. The presented MRE is homogeneous with uniform distribution of CIP. The most significant recent developments of systematic correlation between the effects of microstructural deformation and durability performance of MRE under stress relaxation has been observed and evaluated.
Micro mechanism consideration is critical for gaining a thorough understanding of amorphous shear band behavior in magnetorheological (MR) solids, particularly those with viscoelastic matrices. Heretofore, the characteristics of shear bands in terms of formation, physical evolution, and response to stress distribution at the localized region have gone largely unnoticed and unexplored. Notwithstanding these limitations, atomic force microscopy (AFM) has been used to explore the nature of shear band deformation in MR materials during stress relaxation. Stress relaxation at a constant low strain of 0.01% and an oscillatory shear of defined test duration played a major role in the creation of the shear band. In this analysis, the localized area of the study defined shear bands as varying in size and dominantly deformed in the matrix with no evidence of inhibition by embedded carbonyl iron particles (CIPs). The association between the shear band and the adjacent zone was further studied using in-phase imaging of AFM tapping mode and demonstrated the presence of localized affected zone around the shear band. Taken together, the results provide important insights into the proposed shear band deformation zone (SBDZ). This study sheds a contemporary light on the contentious issue of amorphous shear band deformation behavior and makes several contributions to the current literature.
Temperature is one of the most influential factors affecting the performance of elastomer matrix in magnetorheological elastomer (MRE). Previous studies have utilized silica as a reinforcing filler in polymer composite and as a coating material in MRE to improve the thermal stability of the base material. However, the usage of silica as an additive in the thermal stability of MRE has not been explored. Thus, in this study, the effect of silica as an additive on the temperature-dependent mechanical and rheological properties of ethylene propylene diene monomer (EPDM)-based MREs was investigated by using 30 wt.% carbonyl iron particles (CIPs) as the main filler, with different contents of silica nanoparticles (0 to 11 wt.%). The microstructure analysis was examined by using field-emission scanning electron microscopy (FESEM), while the thermal characterizations were studied by using a thermogravimetric analyzer and differential scanning calorimetry. The tensile properties were conducted by using Instron Universal Testing Machine in the absence of magnetic field at various temperatures. Meanwhile, the rheological properties were analyzed under oscillatory loadings in the influence of magnetic field, using a rotational rheometer at 25 to 65 °C. The results revealed that the temperature has diminished the interfacial interactions between filler and matrix, thus affecting the properties of MRE, where the tensile properties and MR effect decrease with increasing temperature. However, the presence of silica capable improved the thermal stability of EPDM-based MRE by enhancing the interactions between filler and matrix, thus reducing the interfacial defects when under the influence of temperature. Consequently, the incorporation of silica nanoparticles as an additive in EPDM-based MRE requires more exploration, since it has the potential to sustain the properties of MRE devices in a variety of temperature conditions. Thus, the study on the temperature-dependent mechanical and rheological properties of MRE is necessary, particularly regarding its practical applications.
This paper presents the effect of the micro-sized particles on the storage modulus and durability characteristics of magnetorheological elastomers (MREs). The initial phase of the investigation is to determine any associations among the microparticles' weight percent fraction (wt%), structure arrangement, and the storage modulus of MRE samples. In order to carry out this, both isotropic and anisotropic types of MRE samples consisting of the silicone rubber matrix and 50, 60, 70, 75, and 80 wt% microparticles of carbonyl iron fractions are prepared. It is identified from the magneto-rheometer that the increase in storage modulus and decrease in linear viscoelastic region limit are observed in varying consistency depending on wt% and particle arrangement. The consistency of this dependency feature is highlighted by superimposing all of the graphs plotted to create the proposed the samples' behavior model. In response to increasing magnetic stimulation, a sample of 70 wt% microparticles with an isotropic arrangement is found to be significant and stable. The experimentally defined fraction is then used for the durability test as the second phase of the investigation. During this phase, the durability evaluation is subjected to stress relaxation for an extended period of time. After undergoing durability testing, storage modulus performance is decreased by 0.7-13% at various magnetic stimulation levels. This result directly indicates that the storage modulus characteristics of different forms of MRE are sensitive to the different iron particle fractions' and microparticles' alignment. Therefore, important treatments to alter the storage modulus can be undertaken before the practical implementation to accommodate any desired performance of MRE itself and MRE application systems.
It is well known in the field of materials science that a substance's longevity is significantly influenced by its environment. Everything begins with the initial contact on a material's surface. This influence will then deteriorate and have an extended negative impact on the strength of the material. In this study, the effect of natural weathering in tropical climates on magnetorheological elastomer (MRE) was investigated through microstructural evaluation to understand the aging behavior of the environmentally exposed MRE. To understand and elucidate the process, MREs made of silicone rubber and 70 wt% micron-sized carbonyl iron particles were prepared and exposed to the natural weathering of a tropical climate for 90 days. The MRE samples were then mechanically tensile tested, which revealed that Young's modulus increased, while elongation at break decreased. Surface degradation due to weathering was suspected to be the primary cause of this condition. Using scanning electron microscopy (SEM), the degradation of MRE was investigated as a function of morphological evidence. Upon examination through SEM, it was noted that the weathering effects on the morphology of the exposed samples showed distinct characteristics on the degraded surfaces of the MRE, including numerous microvoids, cavities, and microcracks. While these features were not prominent for the MRE itself, they bear resemblance to the effects observed in similar materials like rubber and elastomer. An atomic force microscope (AFM) is used to investigate the surface topography and local degradation conditions. This observation revealed a distinctive degradation characteristic of the MRE in connection to natural weathering in tropical climates. The surface damage of the MRE samples became severe and inhomogeneous during the environmental aging process, and degradation began from the exposed MRE surface, causing the mechanical characteristics of the MRE to significantly change.
Engineering rubber composites have been widely used as main components in many fields including vehicle engineering and biomedical applications. However, when a rubber composite surface area is exposed to heat or sunlight and over a long-term accelerated exposure and lifecycle of test, the rubber becomes hard, thus influencing the mechanical and rheological behavior of the materials. Therefore, in this study, the deterioration of rheological characteristics particularly the phase shift angle (δ) of silicone rubber (SR) based magnetorheological elastomer (MRE) is investigated under the effect of thermal aging. SR-MRE with 60 wt% of CIPs is fabricated and subjected to a continuous temperature of 100 °C for 72 h. The characterization of SR-MRE before and after thermal aging related to hardness, micrograph, and rheological properties are characterized using low vacuum scanning electron microscopy (LV-SEM) and a rheometer, respectively. The results demonstrated that the morphological analysis has a rough surface and more voids occurred after the thermal aging. The hardness and the weight of the SR-MRE before and after thermal aging were slightly different. Nonetheless, the thermo-rheological results showed that the stress-strain behavior have changed the phase-shift angle (δ) of SR-MRE particularly at a high strain. Moreover, the complex mechanism of SR-MRE before and after thermal aging can be observed through the changes of the 'in-rubber structure' under rheological properties. Finally, the relationship between the phase-shift angle (δ) and the in-rubber structure due to thermal aging are discussed thoroughly which led to a better understanding of the thermo-rheological behavior of SR-MRE.
This paper aims to investigate the mechanical and rheological properties of magnetorheological elastomer (MRE) in marine ecosystems. The prepared samples comprised silicone rubber (SR) and 70 wt% micron-sized carbonyl iron particles (CIPs), immersed in an artificial marine ecosystem using salt water (Natrium Chloride) for 30 days. The mechanical properties of MRE samples were evaluated using hardness and quasi-static tensile tests. While the rheometer was used to investigate the rheological properties of their storage modulus condition with magnetic field stimulation. Further analysis of the defects and damages caused by salt water ageing was done through morphological observation using scanning electron microscope (SEM) technology. The results showed that the hardness and tensile strength of MRE samples that were soaked in salt water were affected over time. Lower values of hardness and tensile strength were obtained after 30 days due to the presence of Na+ and Cl-, which acted as an accelerator to the hydrolyzation process of the MRE. The process then, enhanced the water ingress capability into the matrix to cause the molecular changes. Interestingly, for rheological properties, 30 days of salt water ageing allowed the water molecules to move the MRE matrix molecular chains apart, a process known as plasticization and thus increasing the MR effect. Furthermore, morphological evidence was established to determine the MRE changes during salt water ageing. The research findings should greatly contribute to a better understanding of the effect of salt water on the performance of MRE.