Introduction Hepatitis C Virus (HCV) recently was identified as a major cause of post transfusion hepatitis world wide. To evaluate the role of blood transfusion on the prevalence of HCV infection, by testing antibody and RNA as well as the genotypes of HCV .Also to detect if Blood transfusion acts as unconfounding risk factor for HCV infection.
Methods Sera from 3491 pregnant women were investigated for the presence of HCV antibodies (anti-HCV) by using third generation enzyme immunoassay (EIA-3) as screening test, followed by immunoblot assay (Lia Tek-III). In addition 94 sera of studied women were subjected to molecular analysis (at laboratories of Sorin BioMedica - Italy) for the detection of viral RNA and genotypes of HCV. Using RT-PCR & DNA Enzyme immunoassay (DEIA) method.
Results Our study revealed, that seroprevalence rate of HCV specific Ab & RNA were significantly higher (16.32 %, 80% respectively) among women with a history of blood transfusion, compared to those (2.53%, 56.5%) with no such history P=0.0001, P=0.01. And there is a significant direct linear correlation between number of blood transfused and the seropositive rate of anti-HCV (r=0.7, p=0.046). Based on multivariate analysis, interestingly, this study confirmed that, blood transfusion significantly acting as unconfounding risk factor for acquiring HCV infection (Adjusted OR=1.938,95% C.I=1.646-2.28). And the risk of exposure is increases with increased number of blood transfused. Although, we found no significant association between, HCV genotypic distribution and history of blood transfusion. However, high proportion of women with a history of blood transfusion were harboring HCV genotype -4 or 1b, 50%,40%, resepctively.
Conclusions Our study shows, evidence that, blood transfusion acts as unconfounding risk factor for acquiring and in a mode of transmission of HCV infection. Therefore strict screening of blood donor for HCV-Abs and / or RNA is highly recommended.
Contamination of groundwater by harmful substances poses significant risks to both drinking water sources and aquatic ecosystems, making it a critical environmental concern. Most on-land spill events release organic molecules known as light non-aqueous phase liquids (LNAPLs), which then seep into the ground. Due to their low density and organic composition, they tend to float as they reach the water table. LNAPLs encompass a wide range of non-aqueous phase liquids, including various petroleum products, and can, over time, develop carcinogenic chemicals in water. However, due to frequent changes in hydraulic head, the confinement may fail to contain them, causing them to extend outward. When it contaminates water wells, people cannot reliably consume the water. The removal of dangerous contaminants from groundwater aquifers is made more challenging by LNAPLs. It is imperative to analyze the mechanisms governing LNAPL migration. As a response to this need and the associated dispersion of contaminants into adjacent aquifers, we have conducted a comprehensive qualitative literature review encompassing the years 2000-2022. Groundwater variability, soil structure, and precipitation have been identified as the three primary influential factors, ranked in the following order of significance. The rate of migration is shown to rise dramatically in response to changes in groundwater levels. Different saturation zones and confinement have a major effect on the lateral migration velocity. When the various saturation zones reach a balance, LNAPLs will stop moving. Although higher confinement slows the rate of lateral migration, it speeds up vertical migration. Beyond this, the lateral or vertical movement is also influenced by differences in the permeability of soil strata. Reduced mobility and tighter containment are the outcomes of migrating through fine-grained, low-porosity sand. The gaseous and liquid phases of LNAPLs move more quickly through coarse-grained soils. Due to the complexities and uncertainties associated with LNAPL behavior, accurately foreseeing the future spread of LNAPLs can be challenging. Although studies have utilized modeling techniques to simulate and predict LNAPL migration, the inherent complexities and uncertainties in the subsurface environment make it difficult to precisely predict the extent of LNAPL spread in the future. The granular soil structure considerably affects the porosity and pore pressure.
The unsteady two-dimensional laminar g-Jitter mixed convective boundary layer flow of Cu-water and Al2O3-water nanofluids past a permeable stretching sheet in a Darcian porous is studied by using an implicit finite difference numerical method with quasi-linearization technique. It is assumed that the plate is subjected to velocity and thermal slip boundary conditions. We have considered temperature dependent viscosity. The governing boundary layer equations are converted into non-similar equations using suitable transformations, before being solved numerically. The transport equations have been shown to be controlled by a number of parameters including viscosity parameter, Darcy number, nanoparticle volume fraction, Prandtl number, velocity slip, thermal slip, suction/injection and mixed convection parameters. The dimensionless velocity and temperature profiles as well as friction factor and heat transfer rates are presented graphically and discussed. It is found that the velocity reduces with velocity slip parameter for both nanofluids for fluid with both constant and variable properties. It is further found that the skin friction decreases with both Darcy number and momentum slip parameter while it increases with viscosity variation parameter. The surface temperature increases as the dimensionless time increases for both nanofluids. Nusselt numbers increase with mixed convection parameter and Darcy numbers and decreases with the momentum slip. Excellent agreement is found between the numerical results of the present paper with published results.
In this article, an approximate analytical solution of flow and heat transfer for a viscoelastic fluid in an axisymmetric channel with porous wall is presented. The solution is obtained through the use of a powerful method known as Optimal Homotopy Asymptotic Method (OHAM). We obtained the approximate analytical solution for dimensionless velocity and temperature for various parameters. The influence and effect of different parameters on dimensionless velocity, temperature, friction factor, and rate of heat transfer are presented graphically. We also compared our solution with those obtained by other methods and it is found that OHAM solution is better than the other methods considered. This shows that OHAM is reliable for use to solve strongly nonlinear problems in heat transfer phenomena.
Steady two dimensional MHD laminar free convective boundary layer flows of an electrically conducting Newtonian nanofluid over a solid stationary vertical plate in a quiescent fluid taking into account the Newtonian heating boundary condition is investigated numerically. A magnetic field can be used to control the motion of an electrically conducting fluid in micro/nano scale systems used for transportation of fluid. The transport equations along with the boundary conditions are first converted into dimensionless form and then using linear group of transformations, the similarity governing equations are developed. The transformed equations are solved numerically using the Runge-Kutta-Fehlberg fourth-fifth order method with shooting technique. The effects of different controlling parameters, namely, Lewis number, Prandtl number, buoyancy ratio, thermophoresis, Brownian motion, magnetic field and Newtonian heating on the flow and heat transfer are investigated. The numerical results for the dimensionless axial velocity, temperature and nanoparticle volume fraction as well as the reduced Nusselt and Sherwood number have been presented graphically and discussed. It is found that the rate of heat and mass transfer increase as Newtonian heating parameter increases. The dimensionless velocity and temperature distributions increase with the increase of Newtonian heating parameter. The results of the reduced heat transfer rate is compared for convective heating boundary condition and found an excellent agreement.
Particle swarm optimization (PSO) is employed to investigate the overall performance of a pin fin.The following study will examine the effect of governing parameters on overall thermal/fluid performance associated with different fin geometries, including, rectangular plate fins as well as square, circular, and elliptical pin fins. The idea of entropy generation minimization, EGM is employed to combine the effects of thermal resistance and pressure drop within the heat sink. A general dimensionless expression for the entropy generation rate is obtained by considering a control volume around the pin fin including base plate and applying the conservations equations for mass and energy with the entropy balance. Selected fin geometries are examined for the heat transfer, fluid friction, and the minimum entropy generation rate corresponding to different parameters including axis ratio, aspect ratio, and Reynolds number. The results clearly indicate that the preferred fin profile is very dependent on these parameters.
Taking into account the effect of constant convective thermal and mass boundary conditions, we present numerical solution of the 2-D laminar g-jitter mixed convective boundary layer flow of water-based nanofluids. The governing transport equations are converted into non-similar equations using suitable transformations, before being solved numerically by an implicit finite difference method with quasi-linearization technique. The skin friction decreases with time, buoyancy ratio, and thermophoresis parameters while it increases with frequency, mixed convection and Brownian motion parameters. Heat transfer rate decreases with time, Brownian motion, thermophoresis and diffusion-convection parameters while it increases with the Reynolds number, frequency, mixed convection, buoyancy ratio and conduction-convection parameters. Mass transfer rate decreases with time, frequency, thermophoresis, conduction-convection parameters while it increases with mixed convection, buoyancy ratio, diffusion-convection and Brownian motion parameters. To the best of our knowledge, this is the first paper on this topic and hence the results are new. We believe that the results will be useful in designing and operating thermal fluids systems for space materials processing. Special cases of the results have been compared with published results and an excellent agreement is found.
After a decade of research and development, 3D printing is now an established technique in the construction sector, complete with its own set of accepted standards. The use of 3D printing in construction might potentially improve the outcome of the project as a whole. However, traditional strategies are often used in the residential construction industry in Malaysia, which causes serious public safety and health issues along with a negative impact on the environment. In the context of project management, overall project success (OPS) has five dimensions, such as cost, time, quality, safety, and environment. Understanding the role of 3D printing in relation to OPS dimensions in Malaysian residential construction projects would allow construction professionals to adopt 3D printing more easily. The aim of the study was to find the impact of 3D construction printing on OPS while considering the implications for all five dimensions. Fifteen professionals were interviewed to first evaluate and summarise the impact factors of 3D printing using the current literature. Then, a pilot survey was conducted, and the results were checked using exploratory factor analysis (EFA). The feasibility of 3D printing in the building sector was investigated by surveying industry experts. Partial least squares structural equation modelling was used to investigate and validate the fundamental structure and linkages between 3D printing and OPS (PLS-SEM). A strong correlation was found between 3D printing in residential projects and OPS. Highly positive implications are indicated by the environmental and safety dimensions of OPS. Malaysian decision-makers may look to the outcomes of introducing 3D printing into the residential construction industry as a modern method for increasing environmental sustainability, public health and safety, reducing cost and time, and increasing the quality of construction work. With this study's findings in hand, construction engineering management in Malaysia's residential building sector might benefit from a deeper understanding of how 3D printing is used for improving environmental compliance, public health and safety, and project scope.
Oil and gas construction projects are critical for meeting global demand for fossil fuels, but they also present unique risks and challenges that require innovative construction approaches. Artificial Intelligence (AI) has emerged as a promising technology for tackling these challenges, and this study examines its applications for sustainable development in the oil and gas industry. Using a systematic literature review (SLR), this research evaluates research trends from 2011 to 2022. It provides a detailed analysis of how AI suits oil and gas construction. A total of 115 research articles were reviewed to identify original contributions, and the findings indicate a positive trend in AI research related to oil and gas construction projects, especially after 2016. The originality of this study lies in its comprehensive analysis of the latest research on AI applications in the oil and gas industry and its contribution to developing recommendations for improving the sustainability of oil and gas projects. This research's originality is in providing insight into the most promising AI applications and methodologies that can help drive sustainable development in the oil and gas industry.
Polyurea coatings are well recognized for their remarkable protective properties, making them highly appropriate for practical use in the field of concrete building. The use of polyurea coatings in the concrete building business is currently constrained, despite its prevalent application in industrialized nations. The limited use may be ascribed to ambiguities about the determinants of effective implementation in this particular setting, as well as the dearth of extensive study in the realm of new building materials. The primary objective of this research is to assess and conceptualize the key determinants linked to the use of polyurea coatings in concrete building endeavors. Utilizing a quantitative research approach, a comprehensive literature analysis was conducted to identify a total of 21 probable success variables. The reliability of the questionnaire was established by the administration of a pilot survey, and afterwards, an exploratory factor analysis (EFA) was performed to enhance the clarity and precision of the underlying components. The researchers used structural modeling (SEM) approaches to develop a robust model using the primary data obtained from the questionnaire survey. The EFA revealed the presence of five unique constructs that have an impact on the effectiveness of polyurea coatings in concrete building projects. These constructions comprise several characteristics, including environmental considerations, functional requirements, protective properties, execution processes, and creative elements. The significance and relevance of this research are shown by the validation of the study's results using SEM. The study makes a valuable contribution towards the progression of polyurea coating use within the concrete building sector.
The desire to increase resource management efficacy in the construction sector is expanding because of measures to reduce costs, boost productivity, and minimize environmental impact. The Internet of Things (IoT) has the potential to alter resource management in the construction sector by delivering real-time data and insights that may assist decision-makers in optimizing resource allocation and usage. Incorporating Internet of Things (IoT) technology into the construction sector will be investigated in this study to discover how resource management is affected. The aim of the study is to identify the essential aspects that promote optimal IoT integration and to investigate how IoT may influence resource management. The relations between variables and their fundamental elements are investigated using structural equation modelling (SEM). In the context of building projects, the study analyses how IoT integration influences resource allocation and utilization, real-time monitoring, and proactive maintenance. The building sector in Malaysia provides concepts on IoT in resource management. Based on this research's outcomes, there is a distinct association between the utilization of IoT technology and effective resource management in the construction sector. IoT adoption is affected by a multiplicity of issues, including data analytics, data security and privacy, integration and interoperability, scalability, and flexibility. This study contributes to addressing considerable gaps in the corpus of information on IoT technology integration in the construction sector. It analyses how IoT may effect resource management, emphasizing how IoT technology may enhance the efficacy of human, mechanical, and material resources.