(1) The effect has been studied of the oral administration of supplementary thiamine on the thiamine content of milk from sixteen women, whose initial thiamine content was low ; and of the parenteral administration of thiamine to ten women, some of whom initially showed mild, clinical symptoms of beriberi.
(2) The response in the milk content of thiamine to supplementary thiamine, administered either orally or by injection, showed marked variation in different women. While comparatively small doses taken by mouth evoked a marked response in some women, fairly large doses administered by injection failed to produce much response in others.
(3) In some women, a marked increase in the thiamine content of their milk occurred soon after the administration of thiamine, either orally or parenterally. In others, the response was slow and meagre.
(4) The highest thiamine level obtained in a sample of milk was 38.9 ug./100 ml., after the injection, twice daily, of 20 mg. thiamine for six days — a total intake of 240 mg. of thiamine parenterally. The initial milk thiamine level in this case was 2.3 ug./100 ml., but had increased to 16.2ug./100 ml., by the supply of a good diet alone, before the course of injections was commenced.
(5) It would appear, that, in cases where the thiamine content of the milk is low, initial parenteral administration of thiamine must be supplemented by a continued intake of additional thiamine, if a satisfactory level of thiamine in the milk is to be maintained.
Ni3A1 is an intermetallic compound which has unique property with temperature. Annealing is done at temperature 300, 500, and 700°C for 1 hour and analyzed with X-ray Diffraction (XRD) and Energy Dispersive X-ray (EDX) analysis for their crystallographic nature. EDX confirmed the composition of Ni3A1 with exact stoichiometry, whereas the XRD confirmed the crystallographic nature of the material. The mechanical properties by hardness results showed that Ni3A1 has highest Vickers hardness value of 554 HV when it is non-heat treated. Its hardness drops as it undergoes annealing process. Corrosion analysis by tafel test shows that its polarization resistance may increase up to 4145 W cm2 when annealed at high temperature. These results show that Ni3A1 is a promising material to be considered as an alternative automotive body.
A 'green tyre' concept has the advantage of low rolling resistance, improved wet grip and enhanced handling. It has been reported that 3% decrease in rolling resistance is equivalent to 1% fuel saving, thus giving the 'green tyre' economic benefits and customer satisfaction. In this study, epoxidised natural rubber (ENR) compounds containing various loading of silica filler were prepared. The processibility and viscoelastic properties were investigated using the rubber processing analyser and Mooney viscometer. Results showed that the properties were adversely affected by the poor dispersion of silica as supported by the bound rubber measurement. In addition, a reversion in the cure behaviour was also observed as the curing temperature was increased to 170ºC.
A study on the effect of the modify values of x in CaCu3-xMn4+xO12 system has been carried out with x = 0.1, 0.3, 0.5, 0.7 and 0.9. The materials were prepared via solid-state reaction. The preparation conditions have been optimized using thermogravimetry analysis (TGA) technique. Material formations under the reported conditions have been confirmed by X-ray diffraction (XRD) studies. The results show that the formation of CaCu3Mn4O12 started at calcinations temperature of 600 0 C with the presence of raw material and was formed completely at 850 0 C. Field emission scanning electron microscopy (FESEM) analysis indicated that the increase of x value in the composition had changed the microstructures to be more faceted. The impedance spectrum is characterized by the appearance of two semicircle arcs whose pattern of evolution changes with rise of values x in the CaCu3-xMn4+xMn4O12 system. Bulk resistance (Rb) and grain boundary resistance (Rgb) of CaCu3- xMn4+xO12 decreases form 824.24 : to 98.68 : and 418.18 : to 2.20 : respectively, with the increasing of x value.
Finite Element Analysis (FEA) and Computational Fluid Dynamics (CFD) analysis were performed in this work in order to obtain the best design for safety and aerodynamic performance of the bicycle cycling helmet. FEA analysis was computed on two different helmet designs to determine the critical area subjected to impact. A pressure load was applied on the helmets’ outer surface to simulate oblique loading. The critical areas of the helmets were then highlighted and identified, enabling design improvements to be made on both designs. CFD analysis was then executed in order to obtain the lowest drag coefficient number in reducing the air resistance induced by both of the helmet designs, inherently increasing cyclist performance and ensuring competition success.
Phenolic compounds in an aqueous infusion of leaves of Ficus deltoidea (Moraceae), a well-known herbal tea in Malaysia, were analyzed by HPLC coupled to photodiode array and fluorescence detectors and an electrospray ionization tandem mass spectrometer. Following chromatography of extracts on a reversed phase C(12) column, 25 flavonoids were characterized and/or tentatively identified with the main constituents being flavan-3-ol monomers, proanthocyanidins, and C-linked flavone glycosides. The proanthocyanidins were dimers and trimers comprising (epi)catechin and (epi)afzelechin units. No higher molecular weight proanthocyanidin polymers were detected. The antioxidant activity of F. deltoidea extract was analyzed using HPLC with online antioxidant detection. This revealed that 85% of the total antioxidant activity of the aqueous F. deltoidea infusion was attributable to the flavan-3-ol monomers and the proanthocyanidins.