Fenton oxidation, an advanced oxidation process, is an efficient method for the treatment of recalcitrant wastewaters. Unfortunately, it utilizes H2O2 and iron-based homogeneous catalysts, which lead to the formation of high volumes of sludge and secondary pollutants. To overcome these problems, an alternate option is the usage of heterogeneous catalyst. In this study, a heterogeneous catalyst was developed to provide an alternative solution for homogeneous Fenton oxidation. Iron Zeolite Socony Mobile-5 (Fe-ZSM-5) was synthesized using a new two-step process. Next, the catalyst was characterized by scanning electron microscopy, energy-dispersive X-ray spectroscopy, fourier transform infrared spectroscopy, and Brunauer-Emmett-Teller analysis and tested against a model wastewater containing the azo dye Acid Blue 113. Results showed that the loading of iron particles reduced the surface area of the catalyst from 293.59 to 243.93 m2/g; meanwhile, the average particle size of the loaded material was 12.29 nm. Furthermore, efficiency of the developed catalyst was evaluated by performing heterogeneous Fenton oxidation. Taguchi method was coupled with principal component analysis in order to assess and optimize mineralization efficiency. Experimental results showed that under optimized conditions, over 99.7% degradation and 77% mineralization was obtained, with a 90% reduction in the consumption of the developed catalyst. Furthermore, the developed catalyst was stable and reusable, with less than 2% leaching observed under optimized conditions. Thus, the present study proved that newly developed catalyst has enhanced the oxidation process and reduced the chemicals consumption.
Adsorption is one of the most efficient ways to remove heavy metal from wastewater. In this study, the adsorptive removal of hexavalent chromium, Cr (VI) from aqueous solution was investigated using natural zeolite, clinoptilolite, in the form of hollow fibre ceramic membrane (HFCM). The HFCM sample was prepared using phase inversion-based extrusion technique and followed by sintering process at different sintering temperatures in the range of 900-1050 °C. The fabricated HFCM was characterised using scanning electron microscopy (SEM), contact angle, water permeability, and mechanical strength for all HFCMs sintered at different temperatures. The adsorption and filtration test of Cr (VI) were performed using an in-house water permeation set up with a dead-end cross-flow permeation test. An asymmetric structure with sponge- and finger-like structures across the cross-section of HFCM was observed using SEM. Based on the characterisation data, 1050 °C was chosen to be the best sintering temperature as the water permeability and mechanical strength of this HFCM were 29.14 L/m2∙h and 50.92 MPa, respectively. The performance of the HFCM in adsorption/filtration was 44% of Cr (VI) removal at the Cr (VI) concentration of 40 mg/L and pH 4. In addition, the mathematical model was also performed in simulating the experimental data obtained from this study. All in all, the natural zeolite-based HFCM has a potential as a single-step Cr (VI) removal by membrane adsorption for the wastewater treatment.
The atmosphere security and regulation of climate change are being continuously highlighted as a pressing issue. The crisis of climate change owing to the anthropogenic carbon dioxide emission has led many governments at federal and provincial levels to promulgate policies to address this concern. Among them is regulating the carbon dioxide emission from major industrial sources such as power plants, petrochemical industries, cement plants, and other industries that depend on the combustion of fossil fuels for energy to operate. In view of this, various CO2 capture and sequestration technologies have been investigated and presented. From this review, adsorption of CO2 on porous solid materials has been gaining increasing attention due to its cost-effectiveness, ease of application, and comparably low energy demand. Despite the myriad of advanced materials such as zeolites, carbons-based, metal-organic frameworks, mesoporous silicas, and polymers being researched, research on activated carbons (ACs) continue to be in the mainstream. Therefore, this review is endeavored to elucidate the adsorption properties of CO2 on activated carbons derived from different sources. Selective adsorption based on pore size/shape and surface chemistry is investigated. Accordingly, the effect of surface modifications of the ACs with NH3, amines, and metal oxides on adsorption performance toward CO2 is evaluated. The adsorption performance of the activated carbons under humid conditions is also reviewed. Finally, activated carbon-based composite has been surveyed and recommended as a feasible strategy to improve AC adsorption properties toward CO2. The activated carbon surface in the graphical abstract is nitrogen rich modified using ammonia through thermal treatment. The values of CO2 emissions by sources are taken from (Yoro and Daramola 2020).