Removal of Cr(VI) ions from aqueous solution was investigated using modified palm shell activated carbon. Low Molecular Weight Polyethyleneimine (LMW PEI) was used for impregnation purpose. The maximum amount of LMW PEI adsorbed on activated carbon was determined to be approximately 228.2mg/g carbon. The adsorption experiments were carried out in a batch system using potassium dichromate K(2)Cr(2)O(7) as the source of Cr(VI) in the synthetic waste water and modified palm shell activated carbon as the adsorbent. The effects of pH, concentration of Cr(VI) and PEI loaded on activated carbon were studied. The adsorption data were found to fit well with the Freundlich isotherm model. This modified Palm shell activated carbon showed high adsorption capacity for chromium ions.
Palm shell was used to prepare activated carbon using potassium carbonate (K2CO3) as activating agent. The influence of carbonization temperatures (600-1000 degrees C) and impregnation ratios (0.5-2.0) of the prepared activated carbon on the pore development and yield were investigated. Results showed that in all cases, increasing the carbonization temperature and impregnation ratio, the yield decreased, while the adsorption of CO2 increased, progressively. Specific surface area of activated carbon was maximum about 1170 m2/g at 800 degrees C with activation duration of 2 h and at an impregnation ratio of 1.0.
Fenton oxidation, an advanced oxidation process, is an efficient method for the treatment of recalcitrant wastewaters. Unfortunately, it utilizes H2O2 and iron-based homogeneous catalysts, which lead to the formation of high volumes of sludge and secondary pollutants. To overcome these problems, an alternate option is the usage of heterogeneous catalyst. In this study, a heterogeneous catalyst was developed to provide an alternative solution for homogeneous Fenton oxidation. Iron Zeolite Socony Mobile-5 (Fe-ZSM-5) was synthesized using a new two-step process. Next, the catalyst was characterized by scanning electron microscopy, energy-dispersive X-ray spectroscopy, fourier transform infrared spectroscopy, and Brunauer-Emmett-Teller analysis and tested against a model wastewater containing the azo dye Acid Blue 113. Results showed that the loading of iron particles reduced the surface area of the catalyst from 293.59 to 243.93 m2/g; meanwhile, the average particle size of the loaded material was 12.29 nm. Furthermore, efficiency of the developed catalyst was evaluated by performing heterogeneous Fenton oxidation. Taguchi method was coupled with principal component analysis in order to assess and optimize mineralization efficiency. Experimental results showed that under optimized conditions, over 99.7% degradation and 77% mineralization was obtained, with a 90% reduction in the consumption of the developed catalyst. Furthermore, the developed catalyst was stable and reusable, with less than 2% leaching observed under optimized conditions. Thus, the present study proved that newly developed catalyst has enhanced the oxidation process and reduced the chemicals consumption.
Redox mediators supply an effective way to promote electrons (and protons) transport between the electrode and substrate without being in direct physical contact with the electrode. Here, the carbon-based electrodes with Amberlyst-15 as the redox mediator were used in the electrocatalytic reduction to investigate their ability to indirectly convert glycerol into 1,2-propanediol. The process aims to study the influence of different activated carbon compositions (60%, 70%, 80%, and 90% of total weight) in the activated carbon composite (ACC) electrodes on the electrochemical properties, reaction mechanisms, and selectivity of the yielded products. Their electrochemical behavior and physicochemical properties were determined by cyclic voltammetry (CV) and chronoamperometry (CA), followed by FESEM-EDX for the selected ACC electrode. Electroactive surface area (EASA) plays a role in glycerol mass transport and electrons transfer. EASA of 60ACC, 70ACC, 80ACC, and 90ACC (geometrical surface area of 0.50 cm2) were 19.62, 24.50, 36.74 and 30.83 cm2, respectively. With the highest EASA, 80ACC enhanced the mass transport and electrons transfer process that eventually improved its electrocatalytic activity. It outperformed other ACC electrodes by generating Amberlyst-15 radicals (A-15•-) with high current density at low potential (-0.5 V vs. Ag/AgCl). A-15•- served as the electron-donor for the homogeneous redox reaction with glycerol in delivering highly reactive glycerol radical for further intermediates development and generated 1,2-propanediol at -2.5 V vs. Ag/AgCl (current density of -0.2018 A cm-2). High activated carbon content portrayed a dominant role in controlling EASA and favored consecutive acetol-1,2-propanediol production through the C-O bond breakage. From the galvanostatic electrolysis, 1,2-propanediol selectivity was higher on 80ACC (88.6%) compared to 60ACC (61.4%), 70ACC (70.4%) and 90ACC (72.5%). Diethylene glycol formation was found to be the side reaction but preferred low activated carbon percentage in 60ACC and 70ACC.