Displaying all 7 publications

Abstract:
Sort:
  1. Evaluation of the Differences Between Conventional and Digitally Developed Models Used for Prosthetic Rehabilitation in a Case of Untreated Palatal Cleft
    Beh YH, Farook TH, Jamayet NB, Dudley J, Rashid F, Barman A, et al.
    Cleft Palate Craniofac J, 2021 03;58(3):386-390.
    PMID: 32808548 DOI: 10.1177/1055665620950074
    OBJECTIVE: The virtual cone beam computed tomography-derived 3-dimensional model was compared with the scanned conventional model used in the fabrication of a palatal obturator for a patient with a large palatal defect.

    DESIGN: A digitally derived 3-dimensional maxillary model incorporating the palatal defect was generated from the patient's existing cone beam computerized tomography data and compared with the scanned cast from the conventional impression for linear dimensions, area, and volume. The digitally derived cast was 3-dimensionally printed and the obturator fabricated using traditional techniques. Similarly, an obturator was fabricated from the conventional cast and the fit of both final obturator bulbs were compared in vivo.

    RESULTS: The digitally derived model produced more accurate volumes and surface areas within the defect. The defect margins and peripheries were overestimated which was reflected clinically.

    CONCLUSION: The digitally derived model provided advantages in the fabrication of the palatal obturator; however, further clinical research is required to refine consistency.

    Matched MeSH terms: Palatal Obturators*
  2. A denture replication technique following partial maxillectomy: a case report
    Haider KG, Lewis GR
    Quintessence Int, 1994 Jan;25(1):23-6.
    PMID: 8190877
    A variety of problems faces the prosthodontist attempting reconstruction of maxillary defects. There are various treatment options for patients requiring a partial maxillectomy and an obturator prosthesis. Reduced adaptability makes it difficult for the patient to learn to use a new appliance, unless existing skills can be employed. It is therefore helpful to reproduce familiar features of a patient's existing obturator, especially if this has been used successfully over a transition period.
    Matched MeSH terms: Palatal Obturators*
  3. Application of Functional Impression Technique and Use of Silicone as Bulb for Maxillary Obturator
    Rahman AM, Nizami MMUI, Jamayet NB, Husein A
    J Coll Physicians Surg Pak, 2017 May;27(5):319-320.
    PMID: 28599699 DOI: 2623
    Matched MeSH terms: Palatal Obturators*
  4. Closed hollow bulb obturator--one-step fabrication: a clinical report
    Buzayan MM, Ariffin YT, Yunus N
    J Prosthodont, 2013 Oct;22(7):591-5.
    PMID: 23551843 DOI: 10.1111/jopr.12036
    A method is described for the fabrication of a closed hollow bulb obturator prosthesis using a hard thermoforming splint material and heat-cured acrylic resin. The technique allowed the thickness of the thermoformed bulb to be optimized for weight reduction, while the autopolymerized seal area was covered in heat-cured acrylic resin, thus eliminating potential leakage and discoloration. This technique permits the obturator prosthesis to be processed to completion from the wax trial denture without additional laboratory investing, flasking, and processing.
    Matched MeSH terms: Palatal Obturators*
  5. Rehabilitation of an extraoral and intraoral defect complicated with microstomia. A study case
    Abdulhadi LM
    Eur J Prosthodont Restor Dent, 2012 Jun;20(2):81-5.
    PMID: 22852525
    A 72-year-old man was referred from the surgery department for rehabilitation following surgical resection of Basaloid carcinoma. The first surgical intervention involved the anterior palatal region and was restored with a simple obturator. Two years later further surgery was undertaken to excise a recurrent tumor in the nose and part of the cheek. This resulted in an exposed nasal cavity and maxillary sinus. In addition, there was a small oral aperture composed of thin tissue that stretched to its maximum due to scar formation. The defect was restored with a full thickness skin flap but it subsequently broke down leaving the midface exposed with limited mouth opening due to tissue contraction and scar formation after the flap operation. The defect was rehabilitated with Co-Cr obturator intraorally and a silicone nose retained to the naso-palatal extension of the obturator by a magnet extraorally. This resulted in practically good retention, placement, and adaptation of the two parts of the prosthesis.
    Matched MeSH terms: Palatal Obturators*
  6. Multiple retentive means for prosthetic restoration of a large facial defect - a case report
    Abdulhadi LM
    Chin J Dent Res, 2010;13(1):61-6.
    PMID: 20936194
    A 70-year-old man who suffered from extensive extra and intraoral defects was rehabilitated with a prosthesis using multiple retaining means. The treatment was performed in two parts: externally involving the construction of an episthesis supported only by the remaining intact boundaries of the defect and retained by mini-dental implants and spectacle frame with a modified ear hook; and intraorally by an acrylic resin obturator to restore the function of the hemi-sectioned hard and soft palate. The episthesis was securely retained with minimal movement and/or dislodgment of the prosthesis during function. Multiple retentive techniques may be used to fix heavy external prostheses as an alternative to conventional implants or biological adhesives.
    Matched MeSH terms: Palatal Obturators
  7. Postnatal treatment factors affecting craniofacial morphology of unilateral cleft lip and palate (UCLP) patients in a Japanese population
    Alam MK, Iida J, Sato Y, Kajii TS
    Br J Oral Maxillofac Surg, 2013 Dec;51(8):e205-10.
    PMID: 23099108 DOI: 10.1016/j.bjoms.2012.10.001
    We have evaluated the craniofacial morphology of Japanese patients with unilateral cleft lip and palate (UCLP) and assessed the various postnatal factors that affect it. Lateral cephalograms of 140 subjects (mean (SD) aged 7 (2) years) with UCLP were taken before orthodontic treatment. Surgeons from Hokkaido University Hospital had done the primary operations. The craniofacial morphology was assessed by angular and linear cephalometric measurements. Cheiloplasty, palatoplasty, and preoperative orthopaedic treatment were chosen as postnatal factors. To compare the assessments of the postnatal factors, we made angular and linear cephalometric measurements for each subject and converted them into Z scores in relation to the mean (SD) of the two variables. Subjects treated by the modified Millard cheiloplasty had larger sella-nasion-point A (SNA) and nasion-point A-pogonion (NA-POG) measurements than subjects treated by the modified Millard with a vomer flap cheiloplasty. Two-stage palatoplasty showed consistently better craniofacial morphology than the other palatoplasty. Subjects who had preoperative orthopaedic treatment with a Hotz plate had significantly larger upper incisor/sella-nasion (U1-SN) measurements than who had no preoperative orthopaedic treatment or an active plate. We conclude that in subjects treated by a modified Millard type of cheiloplasty, a two-stage palatoplasty, and a Hotz plate there were fewer adverse effects on craniofacial morphology.
    Matched MeSH terms: Palatal Obturators
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links