Conductive materials are potential candidates for developing bone tissue engineering scaffolds as they are nontoxic and can enhance bone tissue regeneration. Their bioactivity can be enhanced by depositing biomineralization in simulated body fluid (SBF). In the current study, a composite electrospun membrane made up of poly(lactic) acid, poly(3-hydroxybutyrate-co-3-hydroxyvalerate), and hydroxyapatite was fabricated using an electrospinning method. The fabricated membranes were dip-coated with a conductive polymer solution, poly(3,4-ethylenedioxythiophene) poly(4-styrenesulfonate), to induce conductivity. Characterization of the membranes based on characteristics such as morphology, chemical bonding, and wettability was conducted using scanning electron microscopy, field emission scanning electron microscopy, energy-dispersive X-ray spectroscopy, attenuated total reflectance Fourier transform infrared spectroscopy, and contact angle measurement. From the results, biomineralization of both coated and noncoated composite membranes was observed on the surface of nanofibers after 21 days in SBF. The membranes provide a superhydrophilic surface as shown by the contact angle. In conclusion, this biomimetic electrospun composite membrane could be used to further support cell growth for bone tissue engineering application.
Transition metals play an important role in the growth of carbon nanotubes (CNTs). Series of unsupported hybrid catalysts consisting of Ni:Cu, Ni:Cr, and Ni:Mn doped with Nd catalyst, respectively were synthesized by impregnation method. The catalytic performance of the catalyst for the production of CNTs was measured in the pyrolysis process of hydrocarbon source by catalytic chemical vapour deposition method. Acetylene gas was used as the source of carbon in the pyrolysis process. The decomposition of acetylene was carried out at 700ºC. The bulk properties of the catalysts were investigated by X-ray diffraction. Field emission scanning electron microscopy and thermal analysis were used to observe the morphology and thermal stability of the as-synthesized CNTs, respectively. Hybrid catalyst of Ni:Mn/Nd and Ni:Cr/Nd in 3:1 atomic ratio gave high percentage of carbon yield which was assigned for the high production of CNTs with the mass of yield 18 times greater than the initial mass of the catalyst used.
This study was carried out to compare the ultrastructure of fresh, capacitated and acrosome-reacted sperm. The sperm was treated with heparin for capacitation and calcium ionophore for acrosome reaction induction. Sperm samples were then prepared for ultrastructural studies and examined by transmission electron microscopy (TEM). Ultrastructural changes in plasma and acrosomal membranes, shape of the mitochondria and outer dense fibres, in capacitated and acrosome-reacted sperm were evident. The plasma membrane of fresh sperm was loosely fitted around the sperm head and the acrosomal membrane was closely opposed to the nucleus. The plasma and acrosomal membranes of the capacitated sperm were expanded, but disintegrated in the acrosome-reacted sperm. Mitochondria of fresh sperm appeared to be rounded in shape with plasma membrane closely opposed to it and the nine outer dense fibres were almost regular rounded in shape. However, in both capacitated and acrosome-reacted sperm, the mitochondria were almost regular and elongated in shape whilst the outer dense fibres were irregular in shape in the capacitated and acrosome-reacted sperm. There were no noticeable morphological changes found in the axonemal complexes in fresh, capacitated and acrosome-reacted sperm. Ultrastructural studies are able to provide detailed information on sequential events involving numerous physiological changes during fertilization.
This study was conducted to prepare a mixed matrix membrane (MMM) and to test the performance of the prepared MMM for CO2 and CH4 gas separation. MMM containing polyethersulfone (PES) and multi-walled carbon nanotubes (MWCNTs) was prepared by a dry-wet phase inversion technique using a pneumatically-controlled membrane casting machine. The surface modification was performed on MWCNTs in order to enhance the selectivity of CO2/CH4. The surface modification of MWCNTs using chemical and physical approaches has been adopted. Mixed acid (HNO3/H2SO4) and β-CD were used for chemical and physical approaches, respectively. Effects of surface modification on MWCNTs/PES MMM were investigated. MWCNTs/PES MMMs were characterised using scanning electron microscopy (SEM), the Fourier Transform Infrared (FT-IR) spectroscopy and pure gas permeation test. The permeability and selectivity, which are the parameters describing membrane performance were calculated via the data obtained from pure gas permeation test with the feed pressure difference from 3 to 7 bars. In this study, surface modified MWCNTs/PES MMM using mixed acid and β-CD has successfully enhanced the CO2/CH4 selectivity by 40.6% compared to that of neat PES.
Co(II)-Ti(IV)-substituted magnetoplumbite-type (M-type) barium ferrite nanoparticles were synthesized via the sol-gel technique employing ethylene glycol as the gel precursor. Structural and magnetic properties were characterised via X-ray diffraction (XRD), high resolution transmission electron microscopy and superconducting quantum interference device magnetometry. The particle sizes of the M-type BaCoXTiXFe12-2XO19 (0.2 ≤ ≤ 1.0) were found to be 900 Å – 1500 Å. The XRD results confirmed that the Co(II)-Ti(IV) substituted ferrites in the range of 0.2 ≤ ≤ 1.0 substitution had the M-type ferrite as the dominant phase. The hysteresis loss per-cycle decreased with increasing Co(II)-Ti(IV) substitution in M-type ferrites which showed reduced values in coercivity and remnant magnetisation with moderate effect on the saturation magnetisation.
Researchers have developed and modified DNA biosensor techniques to provide a fast, simple and sensitive method for detection of human diseases, bacterial food contamination, forensic and environmental research. This study describes the physical characterization of screen-printed carbon electrodes using the scanning electron microscope.
In this study polymer electrolytes composed of poly(methyl methacrylate) (PMMA) as a host polymer and ethylene carbonate (EC) as a plasticizer complexed with different lithium salts, i.e. lithium tetrafluoroborate (LiBF4) and lithium triflate (LiCF3SO3) were prepared by the solution casting technique. The conductivities of the films were characterized by impedance spectroscopy. At room temperature, the highest conductivities were 4.07 × 10–7S cm–1 and 3.40 × 10–5 S cm–1 achieved, respectively from the films containing 30 wt% LiBF4 in the PMMA-EC-LiBF4 system and 35 wt% LiCF3SO3 in the PMMA-EC-LiCF3SO3 system. The conductivity-temperature dependence of the films seemed to obey the Arrhenius equation in which the ion transport in these materials was thermally assisted. Scanning electron microscopy analysis showed that the surface of PMMA-EC-LiCF3SO3 film was smooth and homogeneous, hence lithium ions could traverse through the PMMA-EC-LiCF3SO3 film more easily compared to the PMMA-EC-LiBF4 film. X-Ray diffraction studies revealed that complexation had occurred and the complexes formed were amorphous.
A feasible production of poly (methyl methacrylate)@alloy (gold-silver) core shell has
been presented as candidate in enhanced detection of surface enhanced Raman scattering
(SERS). Free emulsifier- emulsion synthesised PMMA sphere with average size of 419 nm in
diameter were used as core material for incorporation of alloy nanoparticles (6 nm) resulting
a core-shell structure. The fabrication of PMMA@alloy SERS substrate was successfully
done via self-assembly thus the produced SERS substrate that comprise of unique optical
properties combination arising from periodic core arrangement and plasmonic activity of
alloy nanoparticles. Alloy is bimetallic nanoparticles in which the combination of silver
(Ag) and gold (Au) present an absolutely improved light resistance as compared to single
metal alone with great surface plasmon resonance. Morphology and elemental analysis was
performed through scanning electron microscope (SEM) and the analysis showing species of
both Au and Ag in single alloy nanoparticles. The alloy nanoparticles were also observed to
homogenously coating the PMMA sphere. Surface plasmon resonance activity was maximum
at 476 nm obtained from UV-Visible spectroscopy. High surface production was observed
to have periodically arranged PMMA@alloy core -shell and potentially to be used as SERS
substrate.
The development of new adsorbent has rapidly increased in order to overcome the problem
of waste water treatment from heavy metal pollution. The ability of nickel (II)-ion imprinted
polymer (Ni-IIP) as an alternative adsorbent for the removal of nickel ion from aqueous has
been investigated. The Ni-IIP was prepared via bulk polymerization by using functional
monomers; methylacrylic acid (MAA) with picolinic acid as a co-monomer. Nickel ion was
used as template, AIBN as initiator and EGDMA as cross-linking agent. Non-imprinted control
polymer (NIP) was prepared in the same manner as Ni-IIP but in the absence of nickel
ion. The resultant of Ni-IIP and NIP were characterized by using Fourier Transform Infrared
(FTIR) spectroscopy and Scanning Electron Microscope (SEM). Result showed that, the adsorption
of nickel ion onto Ni-IIP increased as the adsorbent dosage increased and contact
time is prolonged. The adsorption isotherm model for Ni-IIP and NIP were fitted well with
Freundlich and Langmuir, respectively. Kinetic study for both Ni-IIP and NIP were followed
the pseudo-second order, indicates that the rate-limiting step is the surface adsorption that
involves chemisorption. Selectivity studies showed that the distribution coefficient of Ni2+
was higher compared to Zn2+, Mg2+ and Pb2+. The present work has successfully synthesized
Ni-IIP particles with good potential in recognition of Ni2+ ions in an aqueous medium.
Corrosion is a natural deterioration process that destructs metal surface. Metal of highly
protected by passivation layer such as Stainless Steel 316L also undergoes pitting corrosion
when continuously exposed to aggressive environment. To overcome this phenomenon, application
of epoxy based coating with addition of zinc oxide- poly (3,4-ethylenedioxythiophene)
doped with poly (styrene sulphonate) hybrid nanocomposite additive was introduced as
paint/metal surface coating. The compatibility between these two materials as additive
was studied by Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD),
Field Emission Scanning Electron Microscopy/Energy-Dispersive X-ray spectroscopy (FESEM/EDX)
and Transmission Electron Microscopy (TEM) analysis. The effect of nanocomposite
wt.% in epoxy based coating with immersion duration in real environment on corrosion
protection performance was analyzed through potentiodynamic polarization analysis. The
main finding showed that addition of hybrid nanocomposite had increased corrosion protection
yet enhanced corrosion process when excess additives was loaded into epoxy coating.
Addition of 2 wt.% ZnO-PEDOT:PSS was found significantly provided optimum corrosion
protection to stainless steel 316L as the corrosion rate for 0 day, 15 days and 30 days of
immersion duration is 0.0022 mm/yr, 0.0004 mm/yr and 0.0015 mm/yr; respectively.
Biodegradable stents are considered to be a recent innovation, and their feasibility and applicability have been proven in recent years. Research in this area has focused on materials development and biological studies, rather than on how to transform the developed biodegradable materials into the stent itself. Currently available stent technology, the laser cutting-based process, might be adapted to fabricate biodegradable stents. In this work, the fabrication, characterization and testing of biodegradable Fe-Mn stents are described. A standard process for fabricating and testing stainless steel 316L stents was referred to. The influence of process parameters on the physical, metallurgical and mechanical properties of the stents, and the quality of the produced stents, were investigated. It was found that some steps of the standard process such as laser cutting can be directly applied, but changes to parameters are needed for annealing, and alternatives are needed to replace electropolishing.
Zoonotic onchocerciasis is a human infection caused by Onchocerca species of animal origins and transmitted by black fly vectors. The reported incidence of this disease has increased throughout the world. This study aims to clarify the vectorial roles of black fly species in zoonotic filarial transmission in Tak province, western Thailand. The integrated approach of morphological and DNA sequence-based analyses was used to identify species of both wild-caught female black flies and infective filarial larvae found in the infected black flies. All of 494 female black flies captured were identified as Simulium nigrogilvum, through scanning electron microscopy (SEM) and DNA sequence analyses based on the cytochrome c oxidase subunit I (COI) and subunit II (COII), and the fast-evolving nuclear elongation complex protein 1 (ECP1) genes. Four females of S. nigrogilvum harbored one to three third-stage larvae (infective larvae) in their thoraces, with an infection rate of 0.81% (4/494). All infective larvae were similar in morphology and size to one another, being identified as Onchocerca species type I (= O. sp. type A), a bovine filaria, originally reported from Japan, and also as O. sp. found in S. nodosum in Thailand, based on their body lengths and widths being 1,068-1,346 µm long by 25-28 µm wide, and morphological characters. Comparisons of cytochrome c oxidase subunit I (COI) and 12S rRNA sequences of mitochondrial DNA (mtDNA) and phylogenetic analyses with those of previous reports strongly supported that all larvae were O. sp. type I. This report is the first indicating the presence of O. sp. type I in Thailand and its vector being S. nigrogilvum.
The fundamental colloidal properties of pristine graphene flakes remain incompletely understood, with conflicting reports about their chemical character, hindering potential applications that could exploit the extraordinary electronic, thermal, and mechanical properties of graphene. Here, the true amphipathic nature of pristine graphene flakes is demonstrated through wet-chemistry testing, optical microscopy, electron microscopy, and density functional theory, molecular dynamics, and Monte Carlo calculations, and it is shown how this fact paves the way for the formation of ultrastable water/oil emulsions. In contrast to commonly used graphene oxide flakes, pristine graphene flakes possess well-defined hydrophobic and hydrophilic regions: the basal plane and edges, respectively, the interplay of which allows small flakes to be utilized as stabilizers with an amphipathic strength that depends on the edge-to-surface ratio. The interactions between flakes can be also controlled by varying the oil-to-water ratio. In addition, it is predicted that graphene flakes can be efficiently used as a new-generation stabilizer that is active under high pressure, high temperature, and in saline solutions, greatly enhancing the efficiency and functionality of applications based on this material.
A knowledge of pollen characters in early-diverging angiosperm lineages is essential for understanding pollen evolution and the role of pollen in angiosperm diversification. In this paper, we report and synthesize data on mature pollen and pollen ontogeny from all genera of Nymphaeales within a comparative, phylogenetic context and consider pollen evolution in this early-diverging angiosperm lineage. We describe mature pollen characters for Euryale, Barclaya, and Nymphaea ondinea, taxa for which little to no structural data exist.
A conspicuous new concept of pathogens living as the microbial societies in the human host rather than free planktonic cells has raised considerable concerns among scientists and clinicians. Fungal biofilms are communities of cells that possess distinct characteristic such as increased resistance to the immune defence and antimycotic agents in comparison to their planktonic cells counterpart. Therefore, inhibition of the biofilm may represent a new paradigm for antifungal development. In this study, we aim to evaluate the in vitro modulation of vulvovaginal candidiasis (VVC)-causing Candida glabrata biofilms using probiotic lactobacilli strains. Probiotic Lactobacillus rhamnosus GR-1 and Lactobacillus reuteri RC-14 were shown to have completely inhibited C. glabrata biofilms and the results were corroborated by scanning electron microscopy (SEM), which revealed scanty structures of the mixed biofilms of C. glabrata and probiotic lactobacilli strains. In addition, biofilm-related C. glabrata genes EPA6 and YAK1 were downregulated in response to the probiotic lactobacilli challenges. The present study suggested that probiotic L. rhamnosus GR-1 and L. reuteri RC-14 strains inhibited C. glabrata biofilm by partially impeding the adherence of yeast cells and the effect might be contributed by the secretory compounds produced by these probiotic lactobacilli strains. Further investigations are required to examine and identify the biofilm inhibitory compounds and the mechanism of probiotic actions of these lactobacilli strains.
In this work, the physicochemical and blood compatibility properties of prepared PU/Bio oil nanocomposites were investigated. Scanning electron microscope (SEM) studies revealed the reduction of mean fiber diameter (709 ± 211 nm) compared to the pristine PU (969 nm ± 217 nm). Fourier transform infrared spectroscopy (FTIR) analysis exposed the characteristic peaks of pristine PU. Composite peak intensities were decreased insinuating the interaction of the bio oilTM with the PU. Contact angle analysis portrayed the hydrophobic nature of the fabricated patch compared to pristine PU. Thermal gravimetric analysis (TGA) depicted the better thermal stability of the novel nanocomposite patch and its different thermal behavior in contrast with the pristine PU. Atomic force microscopy (AFM) analysis revealed the increase in the surface roughness of the composite patch. Activated partial thromboplastin time (APTT) and prothrombin time (PT) signified the novel nanocomposite patch ability in reducing the thrombogenicity and promoting the anticoagulant nature. Finally the hemolytic percentage of the fabricated composite was in the acceptable range revealing its safety and compatibility with the red blood cells. To reinstate, the fabricated patch renders promising physicochemical and blood compatible nature making it a new putative candidate for wound healing application.
Demand for medical implants is rising day by day as the world becomes the place for more diseased and older people. Accordingly, in this research, metallocene polyethylene (mPE), a commonly used polymer was treated with UV rays for improving its biocompatibility. Scanning electron microscopy (SEM) images confirmed the formation of crests and troughs, which depicts the improvement of surface roughness of mPE substrates caused by UV etching. Accordingly, the contact angle measurements revealed that the wettability of mPE-2.5 J/cm2 (68.09º) and mPE-5 J/cm2 (57.93º) samples were found to be increased compared to untreated mPE (86.84º) indicating better hydrophilicity. Further, the UV treated surface exhibited enhanced blood compatibility as determined in APTT (untreated mPE- 55.3 ± 2.5 s, mPE-2.5 J/cm2 - 76.7 ± 4.1 s and mPE-5 J/cm2 - 112.3 ± 2 s) and PT (untreated mPE - 24.7 ± 1.5 s, mPE- 2.5 J/cm2 - 34.3 ± 1.1 s and mPE-5 J/cm2 - 43 ± 2 s) assay. Moreover, the treated mPE-2.5 J/cm2 (4.88%) and mPE-5 J/cm2 (1.79%) showed decreased hemolytic percentage compared to untreated mPE (15.40%) indicating better safety to red blood cells. Interestingly, the changes in physicochemical properties of mPE are directly proportional to the dosage of the UV rays. UV modified mPE surfaces were found to be more compatible as identified through MTT assay, photomicrograph and SEM images of the seeded 3T3 cell population. Hence UV-modified surface of mPE may be successfully exploited for medical implants.
Ayurveda oil contains numerous source of biological constituents which plays an important role in reducing the pain relief caused during bone fracture. The aim of the study is to fabricate the polyurethane (PU) scaffold for bone tissue engineering added with ayurveda amla oil using electrospinning technique. Scanning Electron Microscopy (SEM) analysis showed that the fabricated nanocomposites showed reduced fiber diameter (758 ± 185.46 nm) than the pristine PU (890 ± 116.91 nm). Fourier Infrared Analysis (FTIR) revealed the existence of amla oil in the PU matrix by hydrogen bond formation. The contact angle results revealed the decreased wettability (116° ± 1.528) of the prepared nanocomposites compared to the pure PU (100° ± 0.5774). The incorporation of amla oil into the PU matrix improved the surface roughness. Further, the coagulation assay indicated that the addition of amla oil into PU delayed the blood clotting times and exhibited less toxic to red blood cells. Hence, the fabricated nanocomposites showed enhanced physicochemical and better blood compatibility parameters which may serve as a potential candidate for bone tissue engineering.
The aim of this study was to develop polyurethane (PU) wound dressing incorporated with cobalt nitrate using electrospinning technique. The morphology analysis revealed that the developed composites exhibited reduced fiber and pore diameter than the pristine PU. The electrospun membranes exhibited average porosity in the range of 67% - 71%. Energy-dispersive X-ray spectra (EDS) showed the presence of cobalt in the PU matrix. The interaction of cobalt nitrate with PU matrix was evident in Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). The contact angle results indicated the improved wettability of the prepared PU/cobalt nitrate composites (82° ± 2) than the pure PU (100° ± 1). The incorporation of cobalt nitrate into the PU matrix enhanced the surface roughness and mechanical strength as evident in the atomic force microscopy (AFM) and tensile test analysis. The blood compatibility assays revealed the anticoagulant nature of the prepared composites by displaying prolonged blood clotting time than the PU control. Further, the developed composite exhibited less toxicity nature as revealed in the hemolysis and cytotoxicity studies. It was observed that the PU wound dressing added with cobalt nitrate fibers exhibited enhanced physicochemical, better blood compatibility parameters and enhanced fibroblast proliferation rates which may serve as a potential candidate for wound dressings.