The concentrations of cadmium, copper, zinc and lead, in the total soft tissues of green-lipped mussel Perna viridis of a wide range of sizes (2-11 cm), were determined from a population at Pasir Panjang. The metal contents (μg per individual) and concentrations (μg per g) of cadmium, lead, copper and zinc were studied in P. viridis to find the relationships with body sizes. Smaller and younger mussels showed higher concentrations (μg per g) of Cd, Pb and Zn than the larger and older ones. The results of the present study showed that the plotting of the metal content, against dry body flesh weight on a double logarithmic basis, gave good positive straight lines; this observation is in agreement with Boyden’s formula (1977). This indicated that P. viridis showed a different physiological strategy for each metal being studied, which is related to age.
The removal of heavy metals like lead, copper and cadmium from wastewater streams is an important environmental issue. The capability of immobilized Pycnoporus sanguineus (P. sanguineus), a white-rot macrofungi to remove heavy metals from aqueous solution in a packed bed column was investigated. Lead (Pb (II)) biosorption by immobilized cells of P. sanguineus was investigated in a packed bed column. The experiments were carried out by considering the effect of bed height (5-13 cm), flow rate (4-12 ml min-1) and initial lead (II) concentration (50-300 mg L-1). The breakthrough profiles showed that the saturation of metal ions was achieved faster for 5 cm bed height and 12 ml min-1 influent flow rate. However, the breakthrough time decreased as the initial metal concentration increased from 50 to 300 mg L-1. The column was regenerated using 0.1M HCl solution and biosorptiondesorption studies were carried out for 2 cycles. The results showed that the breakthrough time decreased as the number of cycle was proceeded.
Modelling observed meteorological elements can be useful. For instance, modelling rainfall has
been an interest for many researchers. In a previous research, trend surface analysis was used and
it was indicated that the residuals might spatially be correlated. When dealing with spatial data, any
modelling technique should take spatial correlation into consideration. Hence, in this project, fitting
of spatial regression models, with spatially correlated errors to the annual mean relative humidity
observed in Peninsular Malaysia, is illustrated. The data used in this study comprised of the annual
mean relative humidity for the year 2000-2004, observed at twenty principal meteorological stations
distributed throughout Peninsular Malaysia. The modelling process was done using the S-plus
Spatial Statistics Module. A total of twelve models were considered in this study and the selection
of the model was based on the p-value. It was found that a possible appropriate model for the
annual mean relative humidity should include an intercept and a term of the longitude as covariate,
together with a conditional autoregressive error structure. The significance of the coefficient of the
covariate and spatial parameter was established using the Likelihood Ratio Test. The usefulness
of the proposed model is that it could be used to estimate the annual mean relative humidity at
places where observations were not recorded and also for prediction. Some other potential models
incorporating the latitude covariate have also been proposed as viable alternatives.
The analysis of the spatial data has been carried out in many disciplines such as demography, meteorology, geology and remote sensing. The spatial data modelling is important because it recognizes the phenomenon of spatial correlation in field experiments. Three main categories of the spatial models, namely, the simultaneous autoregressive (SAR) models (Whittle, 1954), the conditional autoregressive (CAR) models (Bartlett, 1971), and the moving average (MA) models (Haining, 1978) have been studied. Whittle (1954) presented a form of bilateral autoregressive (AR) models, whereas Basu and Reinsel (1993) considered the first-order autoregressive moving average (ARMA) model of the quadrant type. Awang, N. and Mahendran Shitan (2003) presented the second-order ARMA model, and established some explicit stationary conditions for the model. When fitting the spatial models and making prediction, it is assumed that, the properties of the process would not change with sites. Properties like stationarities have to be assumed, and for this reason, it was therefore imperative that the researchers had made certain that the process was stationary. This could be achieved by providing the explicit stationarity conditions for the model. The explicit conditions, for a stationary representation of the second-order spatial unilateral ARMA model denoted as ARMA(2,1;2,1), have been established (Awang, N. and Mahendran Shitan, 2003) and in this paper, some explicit conditions are established for a stationary representation of the second-order spatial unilateral ARMA model, denoted as ARMA(2,2;2,2).
The present project investigated the potential of utilizing corncobs and sugar cane waste as viscosivier in drilling fluid. For this purpose, the synthetic-based drilling fluid, Sarapar 147, was used as the base fluid. Both the materials were subjected to pre-treatment of drying, dehumidifying, grinding and sieving process prior to rheological tests. The rheological tests were conducted in accordance with the API 13B specifications to measure mud density, plastic viscosity, yield point, 10-second and 10-minute gel strength. The study found that plastic viscosity and yield point had a direct relationship with the amount of materials added. To drill fluid additive with corn cobs, the density, plastic viscosity and yield point were increased when the amount of additives were increased. Based on these experiments, both additives were found to have the potential to be used as additive in drilling fluid. In particular, they were able to improve its rheological properties by increasing the density, plastic viscosity and yield point. The suitable concentration for the corn cobs and sugar cane is 6.45 lb/bbl and 9.43 lb/bbl, respectively.
A depth-averaged numerical model was developed to study tidal circulation and suspended sediment transport in the gulf of Khambhat along the west coast of India. The spatial resolution of the model is 750m x 750m. A 2-D fine resolution (150 m x 150 m) model for the lower part of the Narmada estuary is coupled with the coarser gulf model to simulate the flow features in the lower estuary. The model dynamics and basic formulation remain the same for both the gulf model and the estuary model. The models are barotropic, based on the shallow water equations and neglect horizontal diffusion and wind stress terms in the momentum equations. The models are fully non-linear and use a semi-explicit finite difference scheme to solve mass, momentum, and advection- diffusion equation for suspended sediments in a horizontal plane. The erosion and deposition have been computed by an empirically developed source and sink term in the suspended sediment equation. The tide in the gulf is mainly represented in the model by the semi-diurnal M2 constituent. Meanwhile, fresh water discharge from the rivers joining the gulf had also been considered. Numerical experiments were carried out to study the circulation and suspended sediment concentrations in the gulf and estuarine region.
Recently, license plate detection has been used in many applications especially in transportation systems. Many methods have been proposed in order to detect license plates, but most of them work under restricted conditions such as fixed illumination, stationary background, and high resolution images. License plate detection plays an important role in car license plate recognition systems because it affects the accuracy and processing time of the system. This work aims to build a Car License Plate Detection (CLPD) system at a lower cost of its hardware devices and with less complexity of algorithms’ design, and then compare its performance with the local CAR Plate Extraction Technology (CARPET). As Malaysian plates have special design and they differ from other international plates, this work tries to compare two likely-design methods. The images are taken using a web camera for both the systems. One of the most important contributions in this paper is that the proposed CLPD method uses Vertical Edge Detection Algorithm (VEDA) to extract the vertical edges of plates. The proposed CLPD method can work to detect the region of car license plates. The method shows the total time of processing one 352x288 image is 47.7 ms, and it meets the requirement of real time processing. Under the experiment datasets, which were taken from real scenes, 579 out of 643 images were successfully detected. Meanwhile, the average accuracy of locating car license plate was 90%. In this work, a comparison between CARPET and the proposed CLPD method for the same tested images was done in terms of detection rate and efficiency. The results indicated that the detection rate was 92% and 84% for the CLPD method and CARPET, respectively. The results also showed that the CLPD method could work using dark images to detect license plates, whereas CARPET had failed to do so.
The application of computer and machines for agricultural production has been one of the outstanding
developments in Malaysian agriculture, especially in overcoming labour shortages in Oil Palm plantations. The on-line automated weedicide sprayer system was developed at Universiti Putra
Malaysia to locate the existence and intensity of weeds in real-time environment and to spray the
weedicides automatically and precisely. During the start of the spraying operation, the web camera
will initially capture the image of weeds. The computer programme will compute the red, green, blue (RGB) values in the form of computer pixel. These values will be used as reference RGB values to be compared with the RGB values of the weeds captured real-time during the spraying operation. The sprayer nozzle will be turned ‘on’ or ‘off’, depending on the percentage or intensity of the green colour pixel value of weeds. The sprayer valve will open the nozzle/s when the camera detected the presence of weeds. The purpose is to reduce wastage, reduce labour, reduce cost, and control environment hazard.
This paper describes the design and development of harvesting system for the gantry system to harvest eggplants. For this purpose, the harvesting robot was successfully designed and fabricated for the gantry system to harvest eggplants. The operation of the harvester was controlled by Programmable Logic Controller (PLC). Basically, the limit switches, DC motor, and relay are connected to the PLC. Meanwhile, a PLC ladder diagram was designed and developed to control the operation of the eggplant harvester. A visual basic programme was developed to interface the harvester with a greenhouse gantry control system. A videogrammetry method was employed to calculate the distance between the stems of eggplants and the cutter of robot end effector. The end effector used electric as its power source and it was controlled via Programmable Logic Controller (PLC). Visual Basic Programme was developed to interface the harvester with the gantry control system. The accuracy of the videogrammetry was tested to be 67.2% for X-axis, 88.2% for Y-axis and 84.7% for Z-axis. Meanwhile, the speed of the end effector for harvester is 2.4 km/h and it could lift up to 55 cm. In order to determine detachment force of eggplant, 16 samples of mature eggplants were tested in a greenhouse, and as a result, more than 22.76 N force was needed to detach a mature eggplant inside the gantry system.
The growth performance of Indian major carp (Catla catla, Ham.) was assessed over a period of six months through formulated feeds consisting of three seaweeds, namely Chlorodesmis fastigiata, Padina tetrastomatica and Stoechospermum marginatum. A relatively slow average growth rate (6.48 g/month) in fishes was observed in the control group. Meanwhile, the maximum and rapid growth rate (13.38 g/month) was observed with Feed-A supplemented with C. fastigiata. Similarly, a comparable growth rate was also observed with Feed-B (11.56 g/month) with P. tetrastomatica. However, the growth rate in fishes was relatively lower (9.05 g/month) with Feed-C containing seaweed S.marginatum. The growth rate in each month was also compared. The maximum attainable growth rate was found to be 12 g in the control group, whereas this was 30 g with Feed-A. The attainable growth was 20 g and 15 g with Feed-B and Feed-C, respectively. In the control group, the maximum increments in weight was recorded in the third (September) and fifth (November) months of rearing, and the increment was considerably reduced after that. The maximum increment in weight was in the second month (August) with Feed-A, and this was followed by a considerable decrease in subsequent months. A similar trend was observed with Feed-B and Feed-C. The biochemical composition of all the four feeds used in the present study showed approximately the same protein (0.45-0.50 mg/ ml) and lipid contents (0.6 mg/ml). Carbohydrate was the only parameter which showed a relatively significant effect (p
The exponential fed-batch cultivation of Bacillus sphaericus UPMB10 in 2 l stirred tank fermenter was performed by feeding the initial batch culture with 14 g l-1 of glycerol according to the algorithm aimed at controlling the specific growth rate (μ) of the bacterium. Very high viable cell count (1.14 x 1010 cfu ml-1), which was four times higher as compared to batch cultivation, was achieved in the fed-batch with a controlled μ at 0.4 h-1. In repeated exponential fed-batch cultivation, consisting of four cycles of harvesting and recharging, a final cell concentration of 1.9 x 1011 cfu ml-1 was obtained at the end of the fourth cycle (46 h). Meanwhile, acetylene reduction of cell samples collected from repeated fed-batch cultivation remained unchanged and was maintained at around 20 nmol C2H2 h-1 ml-1 after prolonged cultivation period, and was comparable to those obtained in batch and exponential fed-batch cultivation. Glycerol could be used as a carbon source for high performance cultivation of B. sphaericus, a nitrogen fixing bacterium, in repeated fed-batch cultivation with high cell yield and cell productivity. The productivity (0.68 g l-1 h-1) for repeated fed-batch cultivation increased about 6 times compared to that obtained in conventional batch cultivation (0.11 g l1 h-1). A innovative method in utilizing glycerol for efficient cultivation of nitrogen fixing bacterium could be beneficial to get more understanding and reference in manipulating the integrated plans for sustainable and profitable biodiesel industry.
Tractor rollover occurs when a tractor tips sideways or backwards and overturns, potentially crushing the operator. Rollovers are typically considered to occur more frequently during a sharp turn at a high speed on sloping terrains, although data show that rollovers do occur on flat land after hitting obstacles or through inappropriate use and hitching of implements. It is important to highlight that tractor overturns are the major cause of death in farm operations. The overturns are as a result of interactions between the tractor operator, the tractor and the environment. A review of the relevant literature reveals that more than 800 people are killed each year in tractor accidents, and for every person killed, at least 40 others are injured. This paper focuses on tractor overturns because they account for more than half of all the tractor-related deaths. In addition, farm tractor operational safety principles are also highlighted.
This paper reports an alternative method for making glass-ceramic from disposal waste water
sludge and soda lime silica (SLS) glass. The glass ceramic samples were prepared from a mixture
of wastewater sludge and SLS glasses, melted at 1375°C for 3 hours and quenched by pouring into
water to obtain a coarse frit. The frit glass was then crushed and sieved to 106μm before it was
pressed to a pellet. The sintering process was performed at various temperatures between 700-
1000°C for 2 hours and morphologically characterized with XRD, SEM, and EDX. Overall results
showed the crystalline phase of diopside sodian-critobalite glass-ceramic is depending on thermal
treatment process and making them attractive to industrial uses such as in construction, tiling, and
glass-ceramic applications.
The specific heats (Csp) of neat polyvinyl alcohol (NPVOH) and 40 phr glycerol plasticized polyvinyl alcohol (PPVOH) were measured using a method known as power compensate differential scanning calorimetry. A high purity sapphire (Al2O3) was used as a reference material. NPVOH has a melting temperature of approximately 480 K, while PPVOH has a value of 30 K lower than NPVOH. The amplitude increment of Csp for NPVOH was also higher than PPVOH at melting stage. Overall, Csp of NPVOH is lower than PPVOH because glycerol has reduced the rigidity of PVOH and subsequently induced the motion of molecular structure at an elevated temperature. Based on the specific heat outcomes, neat PVOH and glycerol plasticized PVOH required 1173.544 J/g and 1946.631 J/g, respectively, to heat from 330 to 550 K.
In this study, dynamic vulcanization process was used to improve the thermal properties of calcium carbonate filled composites. The composites were prepared using a Z-blade mixer at 180oC and rotor speed 50rpm. Thermogravimetric analysis (TGA) and Differential scanning calorimetry (DSC) techniques were used to analyze the thermal properties of the composites. The vulcanized and unvulcanized PP/EPDM composites were filled by CaCO3 at 0, 10, 20, 30, and 40 %wt. Meanwhile, thermogravimetric analysis indicates that the total weight loss of PP/EPDM/CaCO3 composites decreased with increasing filler loading. Dynamic vulcanized composites have higher thermal stability, while the crystallinity of PP/EPDM/CaCO3 composites were increased as compared to unvulcanized composites. Therefore, the thermal properties were improved by the presence of
dynamic vulcanization process.
At least 6 million deaths occurred worldwide are due to cancer and this figure is expected to rise to
15 millions by the year 2020. Colorectal cancer is among the most commonly occurring cancers
both globally and in Malaysia. Numerous studies have shown significant relationships between
various dietary components and the risks for colorectal cancer. Meanwhile, several theories have
been suggested as etiological explanations, one of which is the influence of dietary factors on the
cell proliferation rate. A higher cell proliferation rate is statistically associated with increased risk
of colorectal cancer. However, evidence of a significant relationship between diet and colorectal
adenomas, a potential precursor for colorectal cancer, remains insufficient. Colorectal adenomas or
polyps are vital in their relationship with colorectal cancers as almost 70% of all colorectal cancers
are developed from these polyps. Studying the modifiable risk factors related to polyps will provide
an opportunity for the prevention of colorectal cancer even before it develops. This paper reviews
the available evidence linking dietary factors with the risk for colorectal adenomas. As the numbers
of published studies are limited, of which most are concentrated in Western countries, there is a
need for epidemiological studies in Malaysia to strengthen the evidence of a relationship between
diet and colorectal adenomas.
Two different supercapacitor configurations were fabricated using coconut shell-based activated
carbon. Results for cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and charge-discharge measurements are presented and discussed for both configurations. The results show that coconut shell-based activated carbon is viable economical alternative electrode material to expensive activated carbon (AC) and carbon nano tubes (CNT). Meanwhile, the calculations from the charge-discharge characteristics show that the disk-shape supercapacitor, with 10% polyvinylidene fluoride binder (PVdF), has the highest specific capacitance (70F/g). Thus, the testing shows that the flat-laminated super-capacitor with 10% binder (PVdF) has the lowest (10.1ohms). Sources of high equivalent series resistance (ESR) are proposed and methods of reducing it are also discussed in this paper.
The extract of Cinnamomum microphyllum showed strong antioxidant activity when it was tested against auto-oxidation of linoleic acid, superoxide, and DPPH radical scavenging activity. Further detailed investigations of the plant constituents and bioactivity studies led to the isolation and identification of known compounds consisting of three lignans, a coumarin, an ester and β-sitosterol. The structures of the compounds were determined using detailed spectroscopic analysis. The lignans were found to possess a significant antioxidant activity when tested against the three assay systems.
Due to unavailability of a computer keyboard layout for the Jawi script, users of this script make use of the Arabic keyboard layout for typing texts in this particular script. Obviously, the layout of the Arabic script keyboard is not designed for the ancient writing of the Jawi script. Keeping this in view, a research was conducted to design a new keyboard layout suitable for the users of the Jawi script from an ergonomics point of view, and the outcome of the research is presented in this study. In order to design the Jawi script keyboard layout, the relative finger strengths of both male and female subjects were determined experimentally. The relative frequency of the characters and two special characters (full-stop and comma) that appeared in the script were determined by counting their presence in a large number of texts in the script that represent the workload of the fingers. The keys were rearranged in such a way that the workload of each finger was approximately matched with its relative strength. The newly proposed arrangement of the keys was not much different compared to the Arabic script keyboard layout, and hence it is convenient for users to switch between the layouts.
Redox polymerization of acrylonitrile (AN) with ethyl acrylate (EA) and fumaronitrile (FN), as comonomer and termonomer respectively, were carried out using sodium bisulfite (SBS) and potassium persulphate (KPS) as initiators at 40°C. The actual composition of monomers in copolymers and terpolymers has been characterized by gas chromatography (GC). The effects of EA and FN on the glass transition temperature (Tg) and stabilization temperature have been studied by Differential Scanning Calorimetry (DSC). The degradation behaviour and char yield were obtained by thermogravimetric analysis. Meanwhile, incorporation of 10 mol% of EA in homoPAN system was found to greatly reduce Tg to 66°C as compared to that of the homoPAN (Tg=105°C). The initial cyclization temperature (Ti) was found to be higher (264°C) in comparison to that of homoPAN (246°C). In addition, the incorporation of EA was also shown to reduce the char yield of copolymer to 40%. When FN was incorporated as termonomer, the char yield of poly(AN/EA/ FN) 90/4/6 increased up to 44% after the heat treatment with the lowest Ti (241°C).