Introduction: A prebiotic such as inulin is a well-known functional plant food ingredient. It is capable of stimulating growth of beneficial bifidobacteria in the intestine thus protecting against intestinal infections, preventing constipation, increasing mineral absorption, reducing the incidence of colon cancer, and producing B vitamins. Inulin added to food therefore has to be stable during food processing especially against heat treatment, low pH and Maillard reaction. Methods: Newly developed dark chocolate, DC-1, containing inulin (replacing sugar component) as an added value, was stored at 18oC, 60% relative humidity and 25oC, 80% relative humidity (RH) to determine shelf life stability compared to control dark chocolate, DC-0 (with high content of sugar). Sensory evaluation (quantitative descriptive analysis), water activity (aw), microbiological content and presence of inulin after storage of the prebiotic chocolate under both conditions were evaluated to determine shelf life. Results: The DC-1 chocolate had at least 12 months of shelf life at 18oC, 60% RH with better acceptance than DC-0; moreover, it did not experience microbiological and inulin content changes. At 25oC, 80% RH, the growth of Aspergillus sp. was observed on the surface of both DC-0 and DC-1 with aw >0.50 after a 2-month storage. Conclusion: Shelf life stability of DC-1 is almost similar to DC-0.
A longitudinal study was conducted to relate basal metabolic rate (BMR) with growth during adolescence. Subjects comprise 70 boys and 69 girls aged between ten and thirteen years at the time of recruitment. Parameters studied include anthropometric measurements and BMR, which was measured by indirect calorimetry using the Deltatrac metabolic monitor. Measurements were carried out serially once every six months, with a total of 713 BMR data points collected over three years. Mean BMR of boys aged 11, 12, 13 and 14 years were 4.96 ± 0.63 MJ/day, 5.28 ± 0.71 MJ/day, 5.73 ± 0.68 MJ/day and 5.92 ± 0.63 MJ/day, respectively; while mean BMR of girls in the 10, 11, 12 and 13 year age groups were 4.96 ± 0.63 MJ/day, 4.85 ± 0.63 MJ/day, 5.05 ± 0.55 MJ/day and 4.94 ± 0.51 MJ/day, respectively. Comparison of measured BMR with BMR values predicted from the FAO/WHO/UNU (1985) equations shows that the predictive equations overestimated the BMR of Malaysian boys by 3% and that of girls by 5%. The Henry & Rees (1991) equations for populations in the tropics underestimated BMR of boys and girls by 1% and 2%, respectively. Linear regression equations to predict BMR based on body weight were derived according to sex and age groups. It is recommended that these predictive equations be used for the estimation of BMR of Malaysian adolescents.
The consequence of postoperative infections associated with orthopaedic or biomaterial-associated implants is devastating to both the patients and the surgeons. Bacterial microcolonies adhere to the surface of implants, forming biofilms and then detaching part of itself into free-floating planktonic forms may be the cause of recurrent and persistent infections. These bacteria are very resistant towards antibiotics and require a higher drug concentration than usual in order to eradicate them. Quorem-sensing is regarded as one mechanism of communication or integration between these microorganisms in the biofilm and may even be in the transfer of resistant genes. Disruption of this pathway is regarded as one method of inhibiting its growth and formation. Implant design, technique and stability of fixation as well as the surface characteristics, the material and its biocompatibility may also influence bacterial adhesion. It has been suggested that multi-prong strategies such as prevention and disruption of biofilm formation, parenteral antibiotics, use of antibiotic-impregnated construction materials and altering the intrinsic properties of the implant surface may help to eradicate this menace.
Amitraz poisoning is rare and there has been no reported cases in the Malaysian literature. Ingestion of this compound carries many life threatening side effects. We describe a case of Amitraz poisoning in an 18 years old young adult. He developed hypotension, required ventilatory support and a day of intensive care unit stay. He had a quick recovery after he was treated symptomatically and was discharged well after 3 days.
The Malaysian skincare industry is growing rapidly with a vast number of new sunscreens being produced annually. Inadequate skincare regulations and lack of enforcement have resulted in the overrating of sunscreens’ quality. The objectives of this study were to evaluate the efficacy and safety of the local and international sunscreens and to determine the effects of adding concentrated antioxidants into them. Three local and three internationally manufactured sunscreens were tested for the in vitro Ultraviolet A protection factor (UVAPF), Sun Protection Factor (SPF) and photostability. The creams were spread onto roughened polymethylmethacrylate plates where the absorbance was measured using a spectrophotometer before and after two hours of sunlight irradiation. The procedure was repeated combining available concentrated vitamin C and E creams. International sunscreens were found to have more accurate SPF labels (p=0.009) while local sunscreens were found to be more photostable (p=0.003). However, both sunscreens had inadequate UVAPF (p=0.471). Vitamin C enhanced the SPF values (p= 0.04) of both groups of sunscreens while vitamin E enhanced their photostability (p=0.000). Interestingly, combining vitamins C and E rich creams with the sunscreens had no effect on the SPF and UVAPF values as compared to the use of a single vitamin. More importantly, the combination of vitamins decreased the photostability (p=0.002) of sunscreens as compared to the addition of vitamin E alone. In conclusion, photoprotection is best achieved when sunscreens are used together with creams containing either vitamin C or E alone.
The process of etching is the most crucial part of the work of manufacturing printed circuit boards (PCB). In the etching process by nitric acid, a spent etching waste solution of composition 250 g/L HNO3, 30-40 g/L Cu, 30-40 g/L Sn, 30-40 g/L Pb and 20-25 g/L Fe is produced. High metal concentrations in the spent etching waste solution make it a viable candidate for the recovery of metals. Recovery of metals from spent etching waste solution is a significant concern as the recent growth in production of printed circuit boards has generated a drastic increase of spent etching waste solution each year. This study concerns itself with the recovery of metals from spent etching waste. In this study a dilution was made in order to increase the pH of the solution as spent etching waste solution has high acidity, and the electrowinning method was performed to recover metals from the spent etching waste solution. Glassy carbon and platinum were used as cathode and anode in order to investigate the electrodeposition of metals and cyclic voltammetry investigation suggests that the deposition of metals on glassy carbon electrodes occurs at four different overpotentials mainly at -0.15 V, -0.35 V, -0.45 V and -0.75 V. Microscopy observation demonstrates that there is a deposition of metals by applying the potentials in a set of current-time transient study for a duration of 60 seconds and the metals recovered formed as aggregates.
This paper presents investigations into the development of control schemes for end-point vibration
suppression and input tracking of a flexible manipulator. A constrained planar single-link flexible manipulator is considered and the dynamic model of the system is derived using the assumed mode method. To study the effectiveness of the controllers, a Linear Quadratic Regulator (LQR) was initially developed for control of rigid body motion. This is then extended to incorporate a noncollocated PID controller and a feedforward controller based on input shaping techniques to control vibration (flexible motion) of the system. For feedforward controller, positive and modified specified negative amplitude (SNA) input shapers are proposed and designed based on the properties of the system. Results from the simulation of the manipulator responses with the controllers are presented in time and frequency domains. The performances of the control schemes are assessed in terms of level of vibration reduction, input tracking capability and time response specifications. Finally, a comparative assessment of the control techniques is presented and discussed.
Academic and corporate interest in sustainable product and process development has risen considerably
in recent years. This can be seen by the number of papers published and in particular by special issued of journals. This paper reports the results of a review of published peer-reviewed literature from 1987 to 2012 to provide an up-to-date picture of sustainability and sustainable assessment. A structured methodology is followed to narrow down the search from around 3500 papers to 111. A variety of different sustainability assessment methodologies are reviewed in two classified research areas: product sustainability assessment and process sustainability assessment. In presenting a detailed taxonomy of product and process sustainability assessment methods, the paper also outlines the advantages and weaknesses of the sustainability assessment methods. The review sheds light on the weak points of current research in this area. The paper also highlights several key issues which have to be taken into account in attempting to develop a product or process sustainability assessment research paradigm for future applications in manufacturing systems.
Heuristic Evaluation (HE) is used as a basis in developing a new technique to evaluate usability or
educational computer games known as Playability Heuristic Evaluation for Educational Computer Game (PHEG). PHEG was developed to identify usability problems that accommodate five heuristics, namely, interface, educational elements, content, playability and multimedia. In HE process, usability problems are rated based on severity score and this is followed by presentation of a mean value. The mean value is used to determine the level of usability problems; however, in some cases, this value may not accurate because it will ignore the most critical problems found in a specific part. In developing PHEG, a new quantitative approach was proposed in analyzing usability problems data. Numbers of sub-heuristics for each heuristic involved were taken into account in calculating percentage for each heuristic. Functions to calculate critical problems were also introduced. Evaluation for one educational game that was still in development process was conducted and the results showed that most of the critical problems were found in educational elements and content heuristics (57.14%), while the least usability problems were found in playability heuristic. In particular, the mean value in this analysis can be used as an indicator in identifying critical problems for educational computer games.
Kenaf fibre that is known as Hibiscus cannabinus, L. family Malvaceae is an herbaceous plant that can be grown under a wide range of weather conditions. The uses of kenaf fibres as a reinforcement material in the polymeric matrix have been widely investigated. It is known that epoxy has a disadvantage of brittleness and exhibits low toughness. In this research, liquid epoxidized natural rubber (LENR) was introduced to the epoxy to increase its toughness. Kenaf fibres, with five different fibre loadings of 5%, 10%, 15%, 20% and 25% by weight, were used to reinforce the epoxy resins (with and without addition of epoxidized natural rubber) as the matrices. The flexural strength, flexural modulus and fracture toughness of the rubber toughened epoxy reinforced kenaf fibre composites were investigated. The results showed that the addition of liquid epoxidized natural rubber (LENR) had improved the flexural modulus, flexural strength and fracture toughness by 48%, 30%, and 1.15% respectively at 20% fibre loading. The fractured surfaces of these composites were investigated by using scanning electron microscopic (SEM) technique to determine the interfacial bonding between the matrix and the fibre reinforcement.
The central coast of Tamil Nadu, Andaman and Nicobar Islands, along with other regions, was severely hit by the tsunami on 26 December 2004. A strange spawning behaviour of the Indian horseshoe crabs (Tachypleus gigas, Müller) was observed after the tsunami disturbance. Along the northeast coast of India, the horseshoe crabs normally migrate towards the shore in large numbers coinciding with the tidal height and grain size of the sediment and spawn in nests made in sand. The spawning behaviour was normal until November 2004 and throughout that period about 35 to 45 nests in 200 m2 of area of the breeding beach were examined. However, no nesting was observed from December 2004 to March 2005, i.e. after the occurrence of tsunami. The number of nests per 200 m2 of area (~82) and the number of eggs per nest (750-1000 eggs) were increased considerably when the normal conditions were restored in April 2005. The absence of spawning migration, from December 2004 to March 2005, is totally an unusual behaviour and this happened for the first time during the past several years of the study period.
Compartmented Fluidized Bed Gasifier (CFBG), consisting of two compartments - the combustorand gasifier, uses air blown instead of pure oxygen for syngas production in bubbling fluidization mode, eliminating the need of air separation unit, and reducing the capital cost, thus distinguishes it from other traditional ones. Fluidization quality is a determining factor in the CFBG to guarantee its well-lifted behaviour. Previous study, without solid circulation at ambient conditions, brought to the fore the necessity of considering the effect of the minimum allowable effective diameter. The study was then performed in the CFBG cold physical model of 0.66m overall diameter (effective diameter for combustor and gasifier is 0.413m and 0.257m) to investigate the fluidization quality and compare it with the results obtained from the previous cold model of about 1.36 times smaller, but with the same compartmented ratio of 65:35. Different inert particles (river sand, quartz sand and alumina) were used, over a range of aspect ratios, for the aforementioned objective. The results showed that the fluidization quality in the gasifier has not been achieved and the degradation of fluidization quality in the combustor is still observed, notwithstanding the fact that the condition of the minimum allowable effective diameter has been met. The reduction of distributor free area, to increase the distributor pressure drop, showed a marginal effect on the quality. The effect of the minimum allowable effective diameter on fluidization quality in CFBG as well as the interplay of geometric and operational parameters require further studies be carried out. The fluidization quality of the binary mixture is also currently under investigation.
A series of polycrystalline samples (La1-xSmx)0.67Sr0.33MnO3 (X=0.00, 0.05 and 0.10) were prepared using the conventional solid-state reaction method. The XRD analysis indicated that all the samples were fully crystalline and in a single phase with a rhombohedral structure after a sintering at 1200ºC for 24 hours in air. Meanwhile, the Atomic Force Microscopy measurements showed that a small amount of Sm doping in La sites affected the grain growth and this might affect the grain boundary layer, thus resulting in the reduction of the Curie temperature, TC. Extrinsic magnetoresistance (MR) was observed for all the samples with a large negative MR at low field (0-0.1 or 0.2T) region, followed by a slower varying MR at high field (0.1 or 0.2-1T). The highest low-field MR value of -4.6% (at 0.1T) and -6.1% (at 0.2T) were observed for sample X=0.10 and X=0.05, respectively. Hence, these indicated that the extrinsic MR was grain size dependent and was therefore enhanced with a small amount of Sm substitution in La sites.
The presence of airflow during heating process is expected to increase heat uniformity in a closed heating chamber. Circulation of hot air increases the percentage of convective heat transfer. In this study effects of airflow on oven temperature, cake temperature and several cake qualities were investigated. Experimental studies were conducted in convective oven using two different baking modes; with and without airflow. During baking, oven temperatures and internal cake temperature were measured, and images of cake expansion were captured. Results of the study showed that the presence of airflow could maintain the oven temperature within a small range of set point temperature. Temperature in the oven exhibited ±5.5°C fluctuation, approximately 3.5% overshoot that occurred continuously during baking with airflow. On the contrary, higher overshoot (ranging from 15 to 30%) was observed in oven temperature without airflow. Airflow also showed a significant effect (p
Field investigation on the operation of an industrial fluidized bed paddy dryer of 25 t/h capacity available in a processing complex of Padiberas Nasional Berhad (BERNAS) of Malaysia was carried out to assess its drying characteristics, energy consumption and quality of product during two paddy harvesting seasons. A grain drying simulation model was used to predict dryer performance which can be used as a basis for improving drying operations. For the first season (August-September), average drying rate was found to be 538 kg moisture/h to reduce moisture content (mc) from 36.98± 0.89% dry basis (db) to 27.58±0.79% (db) at 100-120°C of drying air temperature with a feed rate (capacity) of 7.75 t/h. In the second season (February-March), average drying rate was found to be 435 kg moisture/h to reduce mc from 28.14 ±0.68% (db) to 22.54 ± 0.69% (db) at 78-90°C drying air temperature with a feed rate of 9.5 t/h. The thermal and electrical energy consumptions were obtained as 7.57 and 0.97 MJ/kg water removed, respectively, for the first season, while 5.92 and 1.2 MJ/kg water removed for the second season. Higher head rice yield and whiteness and lower milling recovery were achieved during the first season than the second season at acceptable milling degree and transparency. Meanwhile, simulation results indicated that the dryer performed better in terms of increased drying capacity during the second than the first season; the dryer could be operated at 150°C to achieve almost double throughput capacity up to 20 t/h for the second season, while for the first season, high mc hindered the capacity to be at or below 7.75 t/h even when using higher a temperature of 160°C to reduce moisture to the desired final moisture of 24-25% (db). Proportion of slower vehicles based on users' opinion poll
In this research wok, three different techniques of change detection were used to detect changes in forest areas. One of the techniques used a local similarity measure approach to detect changes. This new approach of change detection technique, which used mutual information to measure the similarity between two multi-temporal images, was developed based on correspondence of the pixel values, rather than the difference in their intensity. Pixels suffering any changes will be maximally dissimilar. The study was conducted using multi-temporal SPOT 5 satellite images, with the resolution of 10 m x10 m on 5th August 2005 and 13th June 2007. The experimental results show that local mutual information provides more reliable results in detecting changes of the multitemporal images containing different lighting condition compared to the image differencing and NDVI technique, specifically in areas with less plant growth. In addition, it can also overcome the problem on selecting the threshold value. Besides, the findings of this study have also shown that band 3, which is sensitive to vegetation biomass, gave the best result in detecting area of changes compared to the others.
An antimicrobial (AM) Active Packaging can be made by incorporating and immobilizing suitable AM agents into food package matrices and applying a bio switch concept. A starchbased film was prepared and incorporated with an antimicrobial agent, i.e. lysozyme with EDTA as a chelating agent. This film was then inoculated with the bacteria Escherichia coli and Bacillus subtilis to carry out the microbial contamination study. The inhibition of both E. coli and B. subtilis by the AM film was clearly observed as a clear zone formation in the culture agar test. The film appearance showed that lysozymes could give a better inhibition to the growth of E. coli and to B. subtilis, at a satisfying inhibition rate. From the broth test, the decreased in the optical densities were found to be 65.83% and 91.30%, suggesting an effective growth inhibition of E. coli and B. subtilis, respectively. Physically, the film which was incorporated with lysozymes was found to be slightly different from the control film. The moisture content of the film, with lysozymes, was found to be below 10.5%, as compared to the control, after 24 hours of formation in the storage at ambient temperature.
The production of ethanol, from glucose in batch and fed batch culture, was investigated. In the fed batch culture, the glucose feeding was added into the culture at 16th hour of fermentation. The effects of different glucose concentration feeding rates on ethanol fermentation were investigated for fed batch culture. The 2gL-1hr-1 glucose concentration feeding rate was found to give higher ethanol yield (2.47 g ethanol g glucose-1), with respect to substrate consumed as compared to 8 gL-1hr-1 (0.23 g ethanol g glucose-1) and 4 gL-1hr-1 (0.20 g ethanol g glucose-1). The ethanol yield with respect to substrate consumed obtained in batch culture was 0.81 g ethanol g glucose-1. The fed batch culture at 2 gL-1hr-1 glucose concentration feeding rate was proven to be a better fermentation system than the batch culture. The specific growth rate, specific glucose consumption rate and specific ethanol production rate for the fed batch fermentation, at 2 gL-1hr-1 glucose concentration feeding rate, were 0.065 hr-1, 1.20 hr-1 and 0.0009 hr-1, respectively.
Tropical greenhouses require active evaporative cooling system such as pad-and-fan to ensure a suitable microclimate for crop production. Excess heat causes indoor temperature to become hotter than desired resulting in detrimental effects to crop growth and production. Solar radiation intensity and outside temperature affect temperature and relative humidity level inside a greenhouse, while wide gradients in temperature and relative humidity can cause problems related to crop growth and production uniformity. A 300 m2 greenhouse, equipped with evaporative pad and four exhaust fans at each end walls, was used in the study. Horizontal and vertical profiles of the temperature and relative humidity inside the greenhouse were investigated. Results showed that temperature increased from evaporative pad area to exhaust fans area in a horizontal plane, while relative humidity showed an inverse pattern from temperature. In the vertical plane, temperature increased, while relative humidity decreased from lower level to the upper level. ANOVA results showed that in overall, temperature and relative humidity inside the greenhouse were uniform as there was no significant difference at 95% confidence interval. Thus, it was concluded that greenhouse cooling system by evaporative pad and exhaust fans are suitable for application in a tropical country such as Malaysia.
Liberica coffee is the most important coffee species grown in Malaysia. However, there is little or no research at all conducted on coffee berries and green coffee beans since the plant itself is a low income crop in Malaysia. Therefore, research on Malaysian Liberica coffee can help to increase the knowledge of coffee farmers and coffee manufacturers in the processing and handling of the coffee. Physical properties of Liberica coffee berries and beans were investigated the current study. The properties investigated include the size, mass, density, coefficient of friction, angle of repose, fracture force and colour. In comparison to Arabica and Robusta coffee, Liberica coffee has the biggest size, mass, true density and fracture force values but were lower in bulk density in both berries and beans. The Liberica berries and beans were found to be orange-ish and yellowish colour respectively. Angle of repose was low and approximately similar in berries and beans while jute fibre gave the highest friction to both Liberica berries and beans.