Conventional microalgae oil extraction applies physicochemical destruction of dry cell biomass prior to transesterification process to produce fatty acid methyl esters (FAMEs). This report presents a simple and rapid direct transesterification (DT) method for FAMEs production and fatty acid profiling of microalgae using freshly harvested biomass. Results revealed that the FAMEs recovered from Chlorella vulgaris were 50.1 and 68.3 mg with conventional oil-extraction-transesterification (OET) and DT method, respectively. While for Messastrum gracile, the FAMEs recovered, were 49.9 and 76.3 mg, respectively with OET and DT methods. This demonstrated that the DT method increased FAMEs recovery by 36.4% and 53.0% from C. vulgaris and M. gracile, respectively, as compared to OET method. Additionally, the DT method recovered a significantly higher amount of palmitic (C16:0) and stearic (C18:0) acids from both species, which indicated the important role of these fatty acids in the membranes of cells and organelles. The DT method performed very well using a small volume (5 mL) of fresh biomass coupled with a shorter reaction time (~ 15 min), thus making real-time monitoring of FAMEs and fatty acid accumulation in microalgae culture feasible.
3-Monochloropropane-1,2-diol (3-MCPD) esters and glycidyl esters (GE) are heat-induced contaminants which form during oil refining process, particularly at the high temperature deodorization stage. It is worth to investigate the content of 3-MCPD and GE in fries which also involved high temperature. The content of 3-MCPD esters and GE were monitored in fries. The factors that been chosen were temperature and duration of frying, and different concentration of salt (NaCl). The results in our study showed that the effect was in the order of concentration of sodium chloride
The performance of gas chromatography (GC) combined with a hybrid quadrupole time-of-flight (QTOF) mass spectrometry (MS) system for the determination of volatile and semi-volatile compounds in honey samples is evaluated. After headspace (HS) solid-phase microextraction (SPME) of samples, the accurate mass capabilities of the above system were evaluated for compounds identification. Accurate scan electron impact (EI) MS spectra allowed discriminating compounds displaying the same nominal masses, but having different empirical formulae. Moreover, the use of a mass window with a width of 0.005 Da provided highly specific chromatograms for selected ions, avoiding the contribution of interferences to their peak areas. Additional information derived from positive chemical ionization (PCI) MS spectra and ion product scan MS/MS spectra permitted confirming the identity of novel compounds. The above possibilities are illustrated with examples of honey aroma compounds, belonging to different chemical classes and containing different elements in their molecules. Examples of compounds whose structures could not be described are also provided. Overall, 84 compounds, from a total of 89 species, could be identified in 19 honey samples from 3 different geographic areas in the world. The suitability of responses measured for selected ions, corresponding to above species, for authentication purposes is assessed through principal components analysis.
The impacts of rubber variations (clonal, seasonal, and pre-treatment) were investigated to assess changes in the composition of volatile organic compounds (VOCs) emitted during rubber processing. VOC emissions from 14 different rubber types were evaluated by headspace micro-chamber (μ-TEC) extraction coupled with gas chromatography-mass spectrometry (GC-MS). Headspace extracted at 120 °C, which is equivalent to the drying temperature during rubber processing, revealed a significant number of odorants in terms of concentrations as well as odorant type. Volatile fatty acids (VFAs) such as acetic, propanoic, butanoic, pentanoic and hexanoic acids, were frequently detected at concentrations greater than their odour detection thresholds. Other odorous compounds including trimethylamine, p-cresol, butanone, indole, and phenol, were also detected. Emissions collected at ambient conditions represent odorants released during material storage (or maturation) and were dominated by benzene derivatives followed by ketones, aldehydes, esters, and acids. Emission composition during storage appeared to be governed by specific rubber properties such as protein and rubber moisture content. Seasonal variations revealed greater impacts on the concentration of VOCs for all studied clones, compared to pre-treatment variations, suggesting that the VOCs composition was seasonally dependent and may represents the 'potential' emissions from rubber as they are processed. A combination of sensorial and analytical measurements were used to produce odour wheels which may be used as tool to identify key malodours in onsite rubber processing. The linking of odours and odorants can facilitate communication between receptors (the public) and plant operators inorder to minimise odour impact and develop effective abatement and on-site management practices.
Catalysts prepared from industrial wastes rich in Fe, Ca, Si, and Al were used in catalytic upgrading of pyrolysis vapour derived from durian shell and their effect on product yield and properties were compared. With same silica-to-alumina ratio, catalyst prepared from oil palm ash (AS-OPA) with lower Fe and Ca contents gave higher liquid yield (8.32 wt%) with alcohols (28.90%), hydrocarbons (46.00%), and nitrogen-containing compounds (21.46%) while catalyst prepared from electric arc furnace slag (AS-EAF) with higher Fe and Ca contents produced lower liquid yield (50.21 wt%) with high amount of esters (25.80%) and hydrocarbons (72.82%). The presence of AS-OPA and AS-EAF catalysts enhanced deoxygenation degree of bio-oil to 81.13% and 85.49%, respectively. The catalytic performance of AS-EAF at different temperatures (400-600 °C) and AS-EAF/durian shell ratios (1:30, 2:30, 3:30) was investigated. Increasing catalytic temperature enhanced production of bio-oil, reduced oxygenates and enhanced formation of esters. The liquid yield and yield of esters decreased with increasing catalyst loading. Hydrocarbons (mainly neopentane) were the major chemical compounds found in bio-oil produced over AS-EAF. Besides that, AS-EAF showed good deoxygenation performance with highest selectivity of hydrocarbons at 500 °C and AS-EAF/durian shell ratio of 2:30. Catalytic fast pyrolysis of durian shell using waste-derived catalysts is an effective waste management strategy as the bio-oil produced can be a potential alternative source of energy or chemical feedstocks.
The present study describes the conductometric and spectroscopic study of the interaction of reactive anionic dyes, namely, reactive red 223 and reactive orange 122 with the cationic surfactant cetyltrimethyl ammonium bromide (CTAB). In a systematic investigation, the electrical conductivity data was used to calculate various thermodynamic parameters such as free energy (ΔG), enthalpy (ΔH), and the entropy (ΔS) of solubilization. The trend of change in these thermodynamic quantities indicates toward the entropy driven solubilization process. Moreover, the results from spectroscopic data reveal high degree of solubilization, with strong interactions observed in the cases of both dyes and the CTAB. The spontaneous nature of solubilization and binding was evident from the observed negative values of free energies (ΔG p and ΔG b).
Lipase-catalyzed production of triethanolamine-based esterquat by esterification of oleic acid (OA) with triethanolamine (TEA) in n-hexane was performed in 2 L stirred-tank reactor. A set of experiments was designed by central composite design to process modeling and statistically evaluate the findings. Five independent process variables, including enzyme amount, reaction time, reaction temperature, substrates molar ratio of OA to TEA, and agitation speed, were studied under the given conditions designed by Design Expert software. Experimental data were examined for normality test before data processing stage and skewness and kurtosis indices were determined. The mathematical model developed was found to be adequate and statistically accurate to predict the optimum conversion of product. Response surface methodology with central composite design gave the best performance in this study, and the methodology as a whole has been proven to be adequate for the design and optimization of the enzymatic process.
In this study, the methanolysis process of sunflower oil was investigated to get high methyl esters (biodiesel) content using sodium methoxide. To reach to the best process conditions, central composite design (CCD) through response surface methodology (RSM) was employed. The optimal conditions predicted were the reaction time of 60 min, an excess stoichiometric amount of alcohol to oil ratio of 25%w/w and the catalyst content of 0.5%w/w, which lead to the highest methyl ester content (100%w/w). The methyl ester content of the mixture from gas chromatography analysis (GC) was compared to that of optimum point. Results, confirmed that there was no significant difference between the fatty acid methyl ester content of sunflower oil produced under the optimized condition and the experimental value (P ≥ 0.05). Furthermore, some fuel specifications of the resultant biodiesel were tested according to American standards for testing of materials (ASTM) methods. The outcome showed that the methyl ester mixture produced from the optimized condition met nearly most of the important biodiesel specifications recommended in ASTM D 6751 requirements. Thus, the sunflower oil methyl esters resulted from this study could be a suitable alternative for petrol diesels.
Despite the public health importance of Culex pipiens pipiens, their resistance to pirimiphos-methyl insecticides has not been explored enough. Late third and early fourth larvae of Culex pipiens pipiens were collected from three localities between 2003 and 2005 in Northern and Southern Tunisia. All bioassays were carried out using pirimiphosmethyl and propoxur insecticides. Populations of Culex pipiens pipiens were susceptible, moderate and resistant to pirimiphos-methyl insecticide. Resistance to this compound ranged from 2.62 in sample # 2 to 19.9 in sample # 1. The moderate resistance (5.25) was recorded in sample # 3. Synergist's tests showed that the resistance to pirimiphos-methyl was not affected by detoxification enzymes. However, biochemical assays showed the involvement of both metabolic (esterases) and target site (insensitive acetylcholinesterase) resistance mechanisms. The highest frequencies of the resistant phenotypes ([RS] and [RR]) (<0.74) were detected in the most resistant samples (#1). Four esterases enzymes including C1 encoded by the Est-1 locus and three esterases encoded by the Ester super locus: A2-B2, A4-B4 (or A5-B5, which has the same electrophoretic mobility) and B12 were detected. The highest (0.61) and the lowest (0.22) frequencies of these esterases were recorded in samples # 1 (Sidi Hcine) and # 2 (El Fahs) which recorded the highest and the lowest level of resistance, respectively. Monitoring of insecticide resistance should be evaluated regularly for management of vector control.