A series of batch laboratory studies were conducted to investigate the suitability of activated carbon SA2 for the removal of cadmium ions and zinc ions from their aqueous solutions. The single component equilibrium data were analyzed using the Langmuir and Freundlich isotherms. Overall, the Langmuir isotherm showed a better fitting for all adsorptions under investigation in terms of correlation coefficient and error analysis (SSE only 18.2 for Cd2+ and 47.95 for Zn2+). As the binary adsorption is competitive, extended Langmuir models could not predict the binary component isotherm well. The modified extended Langmuir models were used to fit the binary system equilibrium data. The binary isotherm data could be described reasonably well by the modified
extended Langmuir model, as indicated in the error analysis.
A nanofluid is a suspension of nano-sized particles dispersed in a base fluid. It is very much obligatory to know more about stability and thermal characteristics of such a nanofluid for their further use in practical applications. In this research, multiwalled carbon nanotubes (CNT) is dispersed in water. CNT dispersed in water is highly unstable and it sediments rapidly due to the Vander Waals force of attraction. Therefore, to overcome this limitation, xanthan gum (XG) was added which behave as a promising dispersant followed by 4 h water bath sonication. Experimental work includes stability studies using UV Vis spectroscopy with respect to CNT concentration (0.01 and 0.1 wt. %) and XG concentration (0.04 and 0.2 wt. %). The thermal conductivity of the most stable suspensions was measured using KD 2 Pro as a function of temperature (25-70°C) and CNT concentration. The optimum XG concentration was found for each CNT concentration studied. Thermal conductivity was observed to be strongly dependent on temperature and CNT concentration. The dispersion state of the CNT-water nanofluid is further examined using scanning electron microscope (SEM). In short, CNT nanofluids are found to be more suitable for heat transfer applications in many industries due to their enhanced thermal conductivity property. This work provides useful insight on the behavior of CNT nanofluids.
Activated carbon is the preferred adsorbent for gas and water treatment in various industry across the world due to its efficiency, reliability, and accessibility. Recently, in Malaysia, studies are mainly focused on the fabrication of activated carbon from lignocellulosic biomass-based precursors from agricultural waste such as coconut shell, rice husk, and palm kernel shell. Activated carbon fabrication is a two-step process; the precursor will first undergo carbonization, then, activation is carried out either physically or chemically to develop its porous surface for adsorption purposes. The main benefit of activated carbon is the customizable pore structure for different utilization, which can be easily achieved by the chemical activation process. The types and concentration of chemicals used for activation, pre-treatment of precursor, duration of the activation process, and the mass ratio of precursor to chemicals are proven to effectively influence the resulting pore structure. However, the chemicals used in the activation process can be harmful to the environment. Thus, the chemical recovery process is necessary after the activation process. Nonetheless, more in-depth research on producing activated carbon from abundant biomass materials with bio-based chemical agents for activation is needed to achieve an ecological and sustainable manufacturing process.
Room temperature carbon nanotubes (CNT)-based gas sensor was utilised in detection of methane, CH4 gas. The CNT was functionalized with amide group via Fischer esterification process and labelled as CNT-Amide. Silicon dioxide, SiO2 substrate with interdigitated prepatterned gold electrodes were employed as transducers and drop casting technique was used to deposit the multi walled-CNT samples. The electrical properties of the functionalized CNT samples in the exposure of CH4 gas are studied by recorded the changes of resistance using digital multimeter. Concentration of CH4 gas was varied from 1250 ppm to 10 000 ppm. The changes of electrical resistance of CNT-Amide increases with the concentration of tested gas. Sensor response of functionalized CNT are improved more than 10% as compared to pristine CNT. The sensitivity of CNT-Amide also better than CNT-Carboxyl due to the presence of nitrogen element in amide functional group which chemically active to react with CH4 gas. Additionally, fast response of CNT-Amide towards CH4 gas suggested that the functional group enhanced the rate of gas adsorption on sensing layer.
Multi walled-carbon nanotubes (CNT) functionalized with ester was used for detecting methane, CH4 gas at room temperature. Quartz substrate with interdigitated prepatterned gold electrodes was employed as transducers and drop casting method was used to deposit the CNT samples. The electrical properties of the functionalized CNT samples in the presence of CH4 gas were studied and the changes of resistance were recorded using digital multimeter. Concentration of CH4 gas was varied from 0.125 % to 1.0 %. The resistance variation of functionalized CNT increased with the concentration of tested gas. Sensor response of functionalized CNT was improved more than 10 % as compared to pristine CNT. CNT-Ester gives the higher sensitivity due to the presence of ester functional group which act as active site to react with CH4 gas. The fast response of functionalized CNT towards CH4 gas suggested that the functional group enhanced the rate of gas adsorption on sensing layer
Latex production from Hevea brasiliensis rubber tree is the second most important commodity in Malaysia, but this industry is threatened by the white root rot disease (WRD) caused by Rigidoporus microporus that leads to considerable latex yield loss and tree death. This study aimed to characterize and compare the virulence of five R. microporus isolates obtained from infected rubber trees located at different states in Malaysia. These isolates were subjected to morphological and molecular characterization for species confirmation and pathogenicity test for the determination of virulence level. BLAST search showed that the ITS sequences of all the pathogen isolates were 99% identical to R. microporus isolate SEG (accession number: MG199553) from Malaysia. The pathogenicity test of R. microporus isolates conducted in a nursery with 24 seedlings per isolate showed that isolate RL21 from Sarawak has developed the most severe above- and below-ground symptoms of WRD on the rubber clone RRIM600 as host. Six months after being infected with R. microporus, RL21 was evaluated with the highest average of disease severity index of 80.52% for above- and below-ground symptoms, followed by RL22 (68.65%), RL20 (66.04%), RL26 (54.38%), and RL25 (43.13%). The in vitro growth condition tests showed that isolate RL21 of R. microporus has optimum growth at 25-30 °C, with the preference of weakly acidic to neutral environments (pH 6-7). This study revealed that different virulence levels are possessed among different R. microporus isolates even though they were isolated from the same host species under the same climate region. Taken together, field evaluation through visual observation and laboratory assays have led to screening of the most virulent isolate. Determination of the most virulent isolate in the present study is vital and shall be taken into consideration for the selection of suitable pathogen isolate in the development of more effective control measures in combating tenacious R. microporus.