Methane hydrates (MHs) are present in large amounts in the ocean floor and permafrost regions. Methane and hydrogen hydrates are being studied as future energy resources and energy storage media. To develop a method for gas production from natural MH-bearing sediments and hydrate-based technologies, it is imperative to understand the thermal properties of gas hydrates. The thermal properties' measurements of samples comprising sand, water, methane, and MH are difficult because the melting heat of MH may affect the measurements. To solve this problem, we performed thermal properties' measurements at supercooled conditions during MH formation. The measurement protocol, calculation method of the saturation change, and tips for thermal constants' analysis of the sample using transient plane source techniques are described here. The effect of the formation heat of MH on measurement is very small because the gas hydrate formation rate is very slow. This measurement method can be applied to the thermal properties of the gas hydrate-water-guest gas system, which contains hydrogen, CO2, and ozone hydrates, because the characteristic low formation rate of gas hydrate is not unique to MH. The key point of this method is the low rate of phase transition of the target material. Hence, this method may be applied to other materials having low phase-transition rates.
Given the safety issues associated with flammability characteristics of alternative environmentally-friendly refrigerants, it is vital to establish measurement systems to accurately analyse the flammability of these mildly flammable refrigerants. In this study, we used a customised Hartmann bomb analogue to measure the minimum ignition energy (MIE) and laminar burning velocity (BV) for refrigerant/air mixtures of pure ammonia (R717), R32, R1234yf and mixtures of R32 and R1234yf with non-flammable refrigerants of R134a, R125 and carbon dioxide (R744). The MIEs of R717, R32, and R1234yf were measured at an ambient temperature of 24 °C to be (18.0 ± 1.4), (8.0 ± 1.5) and (510 ± 130) mJ at equivalence ratios of 0.9, 1.27 and 1.33, respectively. Adding the non-flammable refrigerants R134a, R125 and R744 along with R32 at volumetric concentrations of 5% each to R1234yf reduced the latter compound's flammability and increased its MIE by one order of magnitude. The laminar burning velocities of pure R717 and R32 were measured at an equivalence ratio of 1.1 using the flat flame method and found to be 8.4 and 7.4 cm/s, respectively. Adding 5% R1234yf to R32 decreased the laminar burning velocity by 11%, while a further 5% addition of R1234yf resulted in a decrease of over 30% in the laminar burning velocity.
The application of time-domain NMR (TD-NMR) analysis to quantify water content in pharmaceutical ingredients is demonstrated. The initial phase of the study employed a range of disintegrants with defined amounts of added water (0-30% of the total weight) as samples; the disintegrants included croscarmellose sodium, corn starch, low-substituted hydroxypropyl cellulose, and crospovidone. After acquisition of the T2 relaxation curves of the samples by TD-NMR measurements, these curves were analyzed by partial least squares (PLS) regression. According to the analysis, accurate and reliable PLS models were created that enabled accurate assessment of water content in the samples. A powder blend consisting of acetaminophen (paracetamol) and tablet excipients was also examined. Both a physical mixture of the powder blend and a wet granule prepared with a high-speed granulator were tested as samples in this study. Precise determination of water content in the powder blend was achieved by using the TD-NMR method. The accuracy of water content determination was equivalent to or better than that of the conventional loss on drying method. TD-NMR analysis samples were measured nondestructively and rapidly with low cost; thus, it could be a powerful quantitative method for determining water content in pharmaceuticals.
Time-domain NMR (TD-NMR) was used for continuous monitoring of the hydration behavior of hydrophilic matrix tablets. The model matrix tablets comprised high molecular weight polyethylene oxide (PEO), hydroxypropyl methylcellulose (HPMC), and polyethylene glycol (PEG). The model tablets were immersed in water. Their T2 relaxation curves were acquired by TD-NMR with solid-echo sequence. A curve-fitting analysis was conducted on the acquired T2 relaxation curves to identify the NMR signals corresponding to the nongelated core remaining in the samples. The amount of nongelated core was estimated from the NMR signal intensity. The estimated values were consistent with the experiment measurement values. Next, the model tablets immersed in water were monitored continuously using TD-NMR. The difference in hydration behaviors of the HPMC and PEO matrix tablets was then characterized fully. The nongelated core of the HPMC matrix tablets disappeared more slowly than that of the PEO matrix tablets. The behavior of HPMC was significantly affected by the PEG content in the tablets. It is suggested that the TD-NMR method has potential to be utilized to evaluate the gel layer properties, upon replacement of the immersion medium: purified (nondeuterated) water is replaced with heavy (deuterated) water. Finally, drug-containing matrix tablets were tested. Diltiazem hydrochloride (a highly water-soluble drug) was employed for this experiment. Reasonable in vitro drug dissolution profiles, which were in accordance with the results from TD-NMR experiments, were observed. We concluded that TD-NMR is a powerful tool to evaluate the hydration properties of hydrophilic matrix tablets.
A vacuum ultraviolet (VUV) field emission lamp was developed by using a neodymium ion doped lutetium fluoride (Nd(3+) : LuF3) thin film as solid-state phosphor and carbon nanofiber field electron emitters. The thin film was synthesized by pulsed laser deposition and incorporated into the lamp. The cathodoluminescence spectra of the lamp showed multiple emission peaks at 180, 225, and 255 nm. These emission spectra were in good agreement with the spectra reported for the Nd(3+) : LuF3 crystal. Moreover, application of an acceleration voltage effectively increased the emission intensity. These results contribute to the performance enhancement of the lamp operating in the VUV region.
Histoplasmosis, caused by Histoplasma capsulatum, is an endemic mycosis in many countries of the world except for Japan. Outbreaks of histoplasmosis among Japanese people are very rare and are mainly imported by travelers. We report an outbreak of histoplasmosis among healthy Japanese people who traveled to a resort area in Southeast Asia. Three young Japanese women traveled to Langkawi island, Malaysia and stayed on the island for five days without visiting caves, a known reservoir of H. capsulatum. All three individuals developed flu-like symptoms with multiple nodule shadows on chest X rays or chest CT scans at around ten days after their return to Japan. Serum samples obtained from the three subjects were positive for anti-Histoplasma antibody and specific PCR for H. capsulatum on lung biopsy specimens and the serum from one patient was positive. The clinical course of all three patients improved without the use of anti-fungal agents and no recurrence has been confirmed. Clinical attendants should consider histoplasmosis when they see patients with flu-like symptoms with abnormal chest X-rays after visiting H. capsulatum endemic areas, especially Southeast Asia.