Ash produced from a hospital waste incinerator was treated using a high temperature melting process at 1200 degrees C. The quality of the produced slag was characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), leaching tests and sequential chemical extraction of metals. The slag contained large amounts of SiO(2,) CaO, Al(2)O(3), Sn, Ni, Cu, Ba and B. XRD analysis revealed a moderate crystal structure for the melted slag and identified the main crystals as quartz (SiO(2)), kaolinite (Al(2)Si(2)O(5)(OH)(4)), albite (NaAlSi(3)O(8)) and gibbsite (Al(OH)(3)). The observed crystal structure assists in preventing the leaching of heavy metals from the slag. Furthermore, the leaching results found the produced slag to comply with disposal limits set by the US EPA. Results from sequential chemical extraction analysis showed that metals in the slag exhibited the strongest preference to be bound to the residual fraction (stable fraction), which is known to have very low leaching characteristics. Melting was found to stabilize heavy metals in hospital waste successfully and therefore it can be an acceptable method for disposal.
Currently, the generated brake lining waste dust, which contains asbestos as its major component, is disposed of into a secure landfill without any additional treatment. As an alternative to this, solidification/stabilization (S/S) disposal of the dust was investigated using Portland cement alone and Portland cement mixed with activated carbon (AC), as the binders. Toxicity Characteristics Leaching Procedure (TCLP) results on the solidified matrix showed that cement was able to immobilize the heavy metals, Ba, Zn, Cr, Pb, Cu and Fe, to within the limits set by the US EPA for TCLP. Addition of AC to the cement reduced the leaching of heavy metals by an additional 4-24% compared to cement alone. The pH of the TCLP leachate extracted from virgin cement, and from dust treated with cement with or without AC was found to increase to 10.9-12.5 as opposed to an initial value of 4.93 for the TCLP extract for the untreated dust. Results of ANS 16.1 (modified) leach protocol revealed that Ba in cement-treated samples showed the highest leach rate, followed by Zn, Pb, Cr, Cu and Fe. The leach rate of heavy metals decreased with progress in time. Cement mixed with AC exhibited similar leach characteristics, however, the leach rate was lower. The linear relationship between the cumulative fraction leached (CFL) and the square root of leaching time in all cement-based samples indicate that a diffusional process is the controlling transport mechanism for the leaching of the heavy metals. The obtained Leachability Indices (L(i)) of 7.6-9.1 and 8.3-9.5 for cement and cement with AC, respectively, were low but exceeded the guidance value of 6, which clearly indicates that all the heavy metals studied are retained well within solid matrices. Cement-based S/S hardening times increased from 30 to 96 h as the dust content increased from 40 to 70 wt.%. The resulting solid matrices exhibited a compressive strength ranging from 1 to 12 MPa, which was well above the specified limit of 414 kPa for such matrices. An economic analysis indicates that the disposal costs for the dust in the only available secure landfill would increase by 40.3% if one were to go for the cement S/S option. Addition of AC to the cement would escalate this by an additional 43.8%. Although the S/S of brake lining dust using cement effectively immobilized the heavy metals of concern, cost considerations may hinder the commercial adaptation of this technique for waste disposal unless new regulatory demands are implemented.
Cadmium (Cd) and lead (Pb) are ubiquitous metals widely distributed in the environment, resulting in toxic health effects. This project aims to evaluate Pb and Cd as toxic elements in 15 different tobacco cigarette brands produced and/or sold in Selangor state, Peninsular Malaysia. The concentrations of Pb and Cd in all tobacco brands tested in this study were determined using the air-acetylene flame atomic absorption spectrophotometer (AAS). On average, the concentrations of Pb and Cd in different tobacco brand samples ranged from 3.05 and 0.80 μg/g dw, respectively. The results indicate that assessment mean values of Pb inhaled from smoking one packet of 20 cigarettes were in the range of 1.55-3.51 μg. Furthermore, the concentration of Cd inhaled per packet of cigarettes (20 sticks) is estimated to be 0.04-0.36 μg. However, there was a significant difference in the concentrations of Pb and Cd between the different brands of tobacco cigarettes, among cigarette prices (cheap versus expensive) of tobacco brands. In conclusion, cigarette smokers in Selangor, Malaysia, are heavily exposed to Pb and Cd, and such exposure could adversely affect their health in the long term. The impact of toxic heavy metals on smokers in this state would be an area for future research.
Efforts to improve water quality have led to the development of green and sustainable water treatment approaches. Herein, nitrogen-doped magnetized hydrochar (mSBHC-N) was synthesized, characterized, and used for the removal of post-transition and transition heavy metals, viz. Pb2+ and Cd2+ from aqueous environment. mSBHC-N was found to be mesoporous (BET surface area - 62.5 m2/g) and paramagnetic (saturation magnetization - 44 emu/g). Both, FT-IR (with peaks at 577, 1065, 1609 and 3440 cm-1 corresponding to Fe - O stretching vibrations, C - N stretching, N - H in-plane deformation and stretching) and XPS analyses (with peaks at 284.4, 400, 530, 710 eV due to C 1s, N 1s, O 1s, and Fe 2p) confirmed the presence of oxygen and nitrogen containing functional groups on mSBHC-N. The adsorption of Pb2+ and Cd2+ was governed by oxygen and nitrogen functionalities through electrostatic and co-ordination forces. 75-80% of Pb2+ and Cd2+ adsorption at Co: 25 mg/L, either from deionized water or humic acid solution was accomplished within 15 min. The data was fitted to pseudo-second-order kinetic and Langmuir isotherm models, with maximum monolayer adsorption capacities being 323 and 357 mg/g for Cd2+and Pb2+ at 318 K, respectively. Maximum Cd2+ (82.6%) and Pb2+ (78.7%) were eluted with 0.01 M HCl, simultaneously allowing minimum iron leaching (2.73%) from mSBHC-N. In conclusion, the study may provide a novel, economical, and clean route to utilize agro-waste, such as sugarcane bagasse (SB), for aquatic environment remediation.
A study was carried out to determine the concentrations of rare earth elements (REEs) in Linggi river sediments collected from 113 sampling locations. The sediment analysis was performed by Neutron activation analysis (NAA) and Inductively coupled plasma - mass spectrometry (ICP-MS). The results of Linggi river sediment were normalized to "recent" reference shale values. The means of total concentrations of REEs (ΣREE), light REEs (ΣLREE) and heavy REEs (ΣHREE) in Linggi sediment were 241.2, 219.2, and 22.0 mg/kg, respectively, which indicates enrichment compared to ΣREE, ΣLREE and ΣHREE reference shale values. Results obtained from enrichment factors (EF) show no enrichment to moderate enrichment of Linggi sediments, indicating the sources of REEs pollution originated from natural and land-based activities. A similar pattern was observed by comparing the REEs values of Linggi sediments to other references shale values. Ce (δCe) and Eu (δEu) anomalies indicate Linggi sediments showed positive anomaly of Ce whilst negative anomaly of Eu.
High population density and economic development attributing to the changes in water quality in Pa Sak River, Lopburi River, and Mekong River have attracted great attention. This research aimed to determine the pollution of heavy metals in collected clams at three different study sites. Bioaccumulation of heavy metals in Asian clam (Corbicula fluminea) may be likely to cause serious health effects on human beings. The clams sampled from three different rivers (Mekong, Pa Sak, and Lopburi) from Thailand were analyzed for the presence of heavy metals (Zn, Cu, Cd, Cr, Mn, and Pb) with an air-acetylene flame atomic absorption spectrophotometer (AAS). Among the heavy metals studied, Zn was recorded as having the highest concentration (127.33-163.65 μg/g) among the three rivers. The observed mean concentration of Cu was in the range of 84.61-127.15 μg/g followed by Mn (13.96-100.63 μg/g), Cr (5.79-15.00 μg/g), Pb (3.43-8.55 μg/g), and Cd (0.88-1.95 μg/g). Overall, Asian clam from Pa Sak River was found to contain high concentrations of Zn, Cu, Cd, Cr, and Pb compared to Mekong and Lopburi River.
This work investigates the metals concentration in the tissues of Asian swamp eel, Monopterus albus. Five selected tissues, including liver, gill, bone, skin, and muscle were examined for the concentration of Zn, Cu, Cd, Pb, and Ni. The concentrations of Cd and Pb were found high in the muscle tissues of the eels. Additionally, high amounts of Zn and Cu metals were observed in the liver, whereas the Cd, Pb, and Ni metals were highly detected in gill. The accumulation of Zn, Cu, Cd, Pb, and Ni in both skin and bone of the eel seems to vary between seasons. Low levels of Zn, Cu, and Ni were identified in the muscle tissues of the eels. This study revealed that the concentration of Cd and Pb in the muscle tissues of Asian swamp eels exceeded the permissible limits by the US EPA, suggesting the consumption of the muscle may be hazardous and can severely affect one's health.
The presence of heavy metal and radionuclides in water bodies has been a long-lasting environmental problem which results in many undesirable consequences. In this framework, the biosorption process, which uses inexpensive and naturally produced material such as alginate, is an alternative technology in the environmental remediation. This review provides relevant and recent literature regarding the application of alginate and its derivatives on removal of various heavy metal ions and radionuclides. The effects of process variables such as solution pH, adsorbent dosage, metal ion concentration, contact time, temperature and co-existing ions used in batch studies in addition to kinetic, isothermal models as well as thermodynamic that fit the adsorption experimental data are critically discussed. This review also includes mechanisms involved during adsorption process. Furthermore, future research needs for the removal of contaminants by alginate-based materials with the aims of improving their adsorption performance and their practical applications are commented.
Rare earth elements (REEs) are becoming significant due to their huge applications in many industries, large-scale mining and refining activities. Increasing usage of such metals pose negative environmental impacts. In this research ICP-MS has been used to analyze soil samples collected from former ex-mining areas in the depths of 0-20 cm, 21-40 cm, and 41-60 cm of residential, mining, natural, and industrial areas of Perak. Principal component analysis (PCA) revealed that soil samples taken from different mining, industrial, residential, and natural areas are separated into four clusters. It was observed that REEs were abundant in most of the samples from mining areas. Concentration of the rare elements decrease in general as we move from surface soil to deeper soils.
This paper reports a wirelessly powered ionic polymer-metal composite (IPMC) soft actuator operated by external radio frequency (RF) magnetic fields for targeted drug delivery. A 183 μm thick IPMC cantilever valve was fitted with an embedded LC resonant circuit to wirelessly control the actuator when the field frequency is tuned to its resonant frequency of approximately 25 MHz. Experimental characterization of the fabricated actuator showed a cumulative cantilever deflection of 160 μm for three repeated RF ON-OFF cycles at 0.6 W input power. The device was loaded with a dye solution and immersed in DI water to demonstrate wireless drug release. The qualitative result shows the successful release of the dye solution from the device reservoir. The release rate can be controlled by tuning the RF input power. We achieved a maximum average release rate of ∼0.1 μl s-1. We further conducted an in vitro study with human tumor cells (HeLa) to demonstrate the proof of concept of the developed device. The experiments show promising results towards the intended drug delivery application.
This review emphasizes the role of toxic metal remediation approaches due to their broad sustainability and applicability. The rapid developmental processes can incorporate a large quantity of hazardous and unseen heavy metals in all the segments of the environment, including soil, water, air and plants. The released hazardous heavy metals (HHMs) entered into the food chain and biomagnified into living beings via food and vegetable consumption and originate potentially health-threatening effects. The physical and chemical remediation approaches are restricted and localized and, mainly applied to wastewater and soils and not the plant. The nanotechnological, biotechnological and genetical approaches required to more rectification and sustainability. A cellular, molecular and nano-level understanding of the pathways and reactions are responsible for potentially toxic metals (TMs) accumulation. These approaches can enable the development of crop varieties with highly reduced concentrations of TMs in their consumable foods and vegetables. As a critical analysis by authors observed that nanoparticles could provide very high adaptability for both in-situ and ex-situ remediation of hazardous heavy metals (HHMs) in the environment. These methods could be used for the improvement of the inbuilt genetic potential and phytoremediation ability of plants by developing transgenic. These biological processes involve the transfer of gene of interest, which plays a role in hazardous metal uptake, transport, stabilization, inactivation and accumulation to increased host tolerance. This review identified that use of nanoremediation and combined biotechnological and, transgenic could help to enhance phytoremediation efficiency in a sustainable way.
The remediation of wastewater requires treatment technologies which are robust, efficient, simple to operate and affordable such as adsorption. Lately, three-dimensional (3D) graphene based materials have attracted significant attention as effective adsorbents for wastewater treatment. The intrinsic properties of 3D graphene structure such as large surface area and interconnected porous structure can facilitate the transport of pollutants into the 3D network and provide abundant active sites for trapping the pollutants. For the synthesis of 3D graphene structure, ice-templating is commonly practiced due to its facile steps, cost effectiveness and high scalability potential. This review covers the ice-templating fabrication technique for 3D graphene based materials and their application as adsorbents in eliminating dyes and heavy metals from aqueous media. The assembly mechanisms of the ice-templating fsynthesis are comprehensively discussed. Further discussion on the fundamental principles, critical process parameters and characteristics of ice-templated 3D graphene structures is also included. A thorough review on the mechanisms for batch adsorption of dyes and heavy metals is presented based on the structures and properties of the 3D graphene materials. The review further evaluates the dynamic adsorption in packed columns and the regeneration of 3D graphene based materials.
The research study was carried out to evaluate trace metals (Pb, Cd, Se, Al, Mn, Cu, Zn, Fe, As, Ni, Cr, and Ag) concentrations in groundwater of Lorong Serai 4, Hulu Langat, Selangor, Malaysia. Additionally, the research study focused on determining non-carcinogenic and carcinogenic health risks, sources of the contaminants, and effective remediation methods. The results show that the concentration levels of Pb, Cd, Se, Al, Cu, Zn, Ni, Cr, and Ag are lower than their corresponding permissible limits, while Fe, Mn, and As concentrations exceed their acceptable limit. The hazard index of the groundwater in the area exceeded the acceptable limit, showing the rate of carcinogenic and non-carcinogenic health effects associated with the water. The findings also indicate that the lifetime cancer risk is high compared to the maximum limits of lifetime cancer risk from the drinking water (10-6 to 10-4). The groundwater geochemical data of the area are used in establishing the source of Fe, Mn, and As metal ions. Evaluation of Fe2+/Fe3+ and S2-/SO42- redox couples and thermodynamic modelling indicates that the groundwater of the area is in redox disequilibrium. The groundwater samples contain aqueous iron sulphate, which is supersaturated, ferrous carbonate and aluminium sulphate that are saturated. The main state of redox disequilibrium is governed by mineral precipitation and dissolution. Aqueous arsenic and manganese are possibly derived from the dissolution of pyrite (arsenopyrite) and amorphous oxide-hydroxides, respectively. The high concentration of iron in the shallow groundwater in the area is primarily the result of silicate rock weathering of ferroan igneous and metamorphic minerals with a minor contribution from the oxidation of iron sulphides. Magnetite coated with graphene oxide (Fe3O4-GO) nanoparticles (NPs) was synthesized and characterized, and the adsorption preliminary experiments were carried out; and the Fe3O4-GO NPs show enhanced removal (Fe > As > Mn) capacity over graphene oxide (GO).
Slipper oyster Crassostrea iredalei is a species of good demand for its sweet flavor and white coloured flesh. The filter feeding nature predisposes oysters to accumulation of pathogenic and heavy metals in waters impacted by sewage pollutions and may thus render the oysters unfit for human consumption. A study was undertaken to investigate the presence of bacteria flora and heavy metal concentrations in cultivated oysters Crassostrea iredalei at Setiu Wetland, Terengganu, the only source of cultivated oysters in East Coast of Malaysia. A total of 200 slipper oyster samples were analyzed. The bacteria were isolated using non selective agar such as TSA agar and selective agars before they were then identified using conventional methods in combination with BBL Crystal identification kit. Heavy metals such as zinc (Zn), copper (Cu), cadmium (Cd), and lead (Pb) concentrations were determined using atomic absorption spectrophotometry. Results showed that the oysters harbor predominantly Shewanella putrifaciens followed by Vibrio parahaemolyticus, Vibrio vulnificus, Vibrio cholerae, Enterobacter cloacae, Escherichia coli and Chromobacterium violaceum. They also contain high concentration of Zn (785.68 +/- 285.88 microg/g) with the lowest heavy metal was Pb (0.17 +/- 0.15 microg/g), whilst the concentrations of other heavy metals were Cu (38.9 +/- 13.2 microg/g) and Cd (1.60 +/- 0.28 microg/g). The study is very useful to evaluate the type of bacteria and heavy metal present in oyster meat for human consumption.
To understand the source-to-sink of pollutants in the Kelantan River estuary and the adjacent shelf area in Malaysia, a total of 42 surface sediment samples were collected in the Kelantan River-estuary-shelf system to analyze for grain size, total organic carbon (TOC) content, Al and heavy metals (Cr, Ni, Cu, Zn, Cd and Pb). The surficial sediments were mainly composed of clayey silt and the TOC content in sediments decreased from the river to the shelf. The surficial sediments experienced Pb pollution; Cr only showed a certain level of pollution in the coastal area of the estuary but not in other areas, and Ni, Cu, Zn, and Cd showed no pollution. The heavy metals mainly originated from natural weathering and erosion of rocks and soils in the catchment and enriched near the river mouth. Total organic carbon can promote the enrichment of heavy metals in sediments.
A study had been carried out to determine Cu, Zn, Cd, Hg and Pb concentrations in the muscle and fins of four elasmobranchs species namely spot-tail sharks, milk sharks, whitespotted bamboo sharks and whitespotted guitarfish from Pulau Kambing LKIM Fishery Complex, Kuala Terengganu, Malaysia. Zinc level was found to have the highest concentration whereas Cd had the lowest concentration in both organs. By comparing both organs, metals concentrations in fins of all elasmobranchs species were higher than muscle. Result obtained was compared with the guidelines set by Malaysian Food Regulation and the provisional tolerable weekly intake was also determined. Current study recommends that the muscle of whitespotted bamboo shark from Kuala Terengganu Waters is likely not to be consumed due to it exceeded the allowable consumption guideline. Finding of this paper is very useful as it provides the baseline data on the pollution status of elasmobranchs in Kuala Terengganu Waters.
In this study, chitosan/poly (ethylene oxide) nanofibres were fabricated at different chitosan:PEO weight ratio by electrospinning process. The effects of chitosan/PEO composition onto adsorption capability for Cu(II), Zn(II) and Pb(II) ions were studied. Formation of beadless fibres were achieved at 60:40 chitosan:PEO ratio. Average fiber diameter, maximum tensile strength and the specific surface area of the beadless fibres were found to be 115±31nm, 1.58MPa and 218m2/g, respectively. Chitosan/PEO composition that produced beadless fibres tend to possess higher hydrophilicity and maximum specific surface area. These characteristics lead the beadless fibres to the maximum adsorption capability. Adsorption equilibrium data were analysed by Langmuir and Freundlich isotherm. Freundlich isotherm showed the better fit with the experimental data and proved the existence of the monolayer adsorption conditions. The maximum adsorption capacity of the beadless fibres for Cu(II), Zn(II) and Pb(II) ions were found to be 120, 117 and 108mgg-1, respectively.