Various studies have been conducted in the past to improve the quality of Malaysian cocoa beans. However, the processing methods still remain crude and lack technological advancement. In terms of drying, no previous study has attempted to apply advanced drying technology to improve bean quality. This paper presents the first attempt to improve the quality of cocoa beans through heat pump drying using constant air (28.6 and 40.4 °C) and stepwise (step-up 30.7-43.6-56.9 °C and step-down 54.9-43.9 °C) drying profiles. Comparison was made against hot air drying at 55.9 °C.
The constituents in a food emulsion interact with each other, either physically or chemically, determining the overall physico-chemical and organoleptic properties of the final product. Thus, the main objective of present study was to investigate the effect of emulsion components on beverage emulsion properties.
This study aims to investigate the textural properties and sensory qualities of cookies made from medium- and long-chain triacylglycerol (MLCT)-enriched margarines. Margarine with formulations of MLCT:palm olein:palm stearin, 60:30:10 and 70:20:10, were selected to produce cookies. The textural properties of cookies were determined using a texture analyser. Quantitative descriptive analysis (QDA) and acceptance test were carried out to describe the attributes and to evaluate the degree of liking of cookies, respectively.
Cell immobilization is an alternative to microencapsulation for the maintenance of cells in a liquid medium. The objective of this study was to evaluate the effects of agrowastes from durian (Durio zibethinus), cempedak (Artocarpus champeden), and mangosteen (Garcinia mangostana) as immobilizers for lactobacilli grown in soymilk. Rinds from the agrowastes were separated from the skin, dried, and ground (150 microm) to form powders and used as immobilizers. Scanning electron microscopy revealed that lactobacilli cells were attached and bound to the surface of the immobilizers. Immobilized cells of Lactobacillus acidophilus FTDC 1331, L. acidophilus FTDC 2631, L. acidophilus FTDC 2333, L. acidophilus FTDC 1733, and L. bulgaricus FTCC 0411 were inoculated into soymilk, stored at room temperature (25 degrees C) and growth properties were evaluated over 168 h. Soymilk inoculated with nonimmobilized cells was used as the control. Utilization of substrates, concentrations of lactic and acetic acids, and changes in pH were evaluated in soymilk over 186 h. Immobilized lactobacilli showed significantly better growth (P < 0.05) compared to the control, accompanied by higher production of lactic and acetic acids in soymilk. Soymilk containing immobilized cells showed greater reduction of soy sugars such as stachyose, raffinose, sucrose, fructose, and glucose compared to the control (P < 0.05).
An improved classification of Orthosiphon stamineus using a data fusion technique is presented. Five different commercial sources along with freshly prepared samples were discriminated using an electronic nose (e-nose) and an electronic tongue (e-tongue). Samples from the different commercial brands were evaluated by the e-tongue and then followed by the e-nose. Applying Principal Component Analysis (PCA) separately on the respective e-tongue and e-nose data, only five distinct groups were projected. However, by employing a low level data fusion technique, six distinct groupings were achieved. Hence, this technique can enhance the ability of PCA to analyze the complex samples of Orthosiphon stamineus. Linear Discriminant Analysis (LDA) was then used to further validate and classify the samples. It was found that the LDA performance was also improved when the responses from the e-nose and e-tongue were fused together.
Radiation processing has been employed successfully for value addition of food and agricultural products. Preliminary studies were undertaken to evaluate the changes induced by ionizing radiation (up to 30 kGy), in the form of gamma irradiation and electron beam irradiation, on some quality attributes and nutritive values of nutraceutically valued lotus seeds. Significant loss in seed firmness was recorded between control and irradiated seeds, irrespective of radiation source. Similarly, the specific viscosity of irradiated lotus seeds decreased significantly up to a dose of 7.5 kGy. Starch increased after exposure to gamma or electron beam irradiation, whereas the total phenolic contents were decreased. Gamma irradiation revealed an enhancement in protein, while the electron beam showed a decrease. Partial oxidation of the seeds during radiation treatments might have occurred as evidenced from the decomposition profiles (thermogravimetry) during heating. It is evident that ionizing radiation brought about significant and variable changes in the quality and nutritive values of lotus seed. Further exploration of this technology for safety and quality is warranted.
Cocoa-specific aroma precursors and methylpyrazines in underfermented cocoa beans obtained from fermentation induced by indigenous carboxypeptidase have been investigated. Fermentation conditions and cocoa bean components were analyzed during 0 to 3 d of fermentation. Underfermented cocoa beans were characterized as having hydrophilic peptides and free hydrophobic amino acids much higher than unfermented ones. These 2 key components of cocoa aroma precursors may be produced from the breakdown of proteins and polypeptides by endogenous carboxypeptidase during the fermentation process. The enzyme was activated during fermentation. Polypeptides of 47, 31, and 19 kDa were observed in the samples throughout the 3-d fermentation period; however, only the first 2 polypeptides were remarkably reduced during fermentation. Since the 1st day of fermentation, underfermented cocoa beans contained methylpyrazines, a dominant group of cocoa-specific aroma. This might be due to microbial activities during fermentation, observed through a decrease of pH value and an increase of temperature of cocoa beans. The concentration of tetramethylpyrazines was significantly increased during the 3 d of fermentation. This may increase the cocoa-specific flavor to the beans.
High-oleic palm oil (HOPO) with an oleic acid content of 59.0% and an iodine value (IV) of 78.2 was crystallized in a 200-kg De Smet crystallizer with a predetermined cooling program and appropriate agitation. The slurry was then fractionated by means of dry fractionation at 4, 8, 10, 12, and 15 degrees C. The oil and the fractionated products were subjected to physical and chemical analyses, including fatty acid composition, triacylglycerol and diacylglycerol composition, solid fat content, cloud point, slip melting point, and cold stability test. Fractionation at 15 degrees C resulted in the highest olein yield but with minimal oleic acid content. Due to the enhanced unsaturation of the oil, fractionation at relatively lower crystallization temperature showed a considerable effect on fatty acid composition as well as triacylglycerol and diacylglycerol composition of liquid fractions compared to higher crystallization temperature. The olein and stearin fractionated at 4 degrees C had the best cold stability at 0 degrees C and sharper melting profile, respectively.
Chicken breast muscle powder (CBMP) and modified waxy cornstarch (MWCS) blends were prepared at different pH conditions (pH 4, 5, 6, 7, 8, and 9). The blends were characterized by light microscopy, frequency sweep, flow analysis, and freeze-thaw stability analysis. Light microscopy showed that the blend structure was coarse at pH conditions close to the isoelectric point of protein and became finer with increasing pH. Frequency sweep demonstrated that the blend was more liquid-like with relatively lower storage (G') and loss (G'') moduli as the pH was increased from pH 4 to pH 9. Flow analysis revealed that thixotropy behavior was evident in samples treated at pHs 4 and 5, whereas antithixotropy was shown by those adjusted to pHs 6, 7, 8, and 9. The CBMP-MWCS blends were found to show better freeze-thaw stability at pH 8 that could be attributed to the formation of a highly interactive network structure of CBMP and MWCS.
Extending the frying-life of oils is of commercial and economic importance. Due to this fact, assessment on the thermal stability of frying oils could provide considerable savings to the food processors. In this study, the physico-chemical properties of five palm products mainly palm oil, single-fractionated palm olein, double-fractionated palm olein, red palm olein and palm-based shortening during 80 hours of heating at 180 degrees C were investigated. Heating properties of these products were then compared with that of high oleic sunflower oil, which was used as reference oil. The indices applied in evaluating the quality changes of oils were free fatty acid, smoke point, p-anisidine value, tocols, polar and polymer compounds. Three palm products i.e. palm oil, single-fractionated palm olein and double-fractionated palm olein were identified to be the most stable in terms of lower formation of free fatty acid, polar and polymer compounds as well as preserving higher smoke point and tocols content compared to the other three oils. The low intensity of hydrolytic and oxidative changes due to prolonged heating, suggests that these palm products are inherently suitable for frying purposes.
Microwave heating was determined in this study to be suitable for the detachment and drying of palm fruits from whole bunches, cut bunches and spikelets. Microwave treatment of the palm fruits was able to attain the objectives of conventional fresh palm fruits sterilization processeses such as fruit softening, nut conditioning and halting of enzymatic lipolysis. Palm oil and kernel oil solvent extracted respectively from the microwave treated whole fruits and kernel were found to have a good quality of low free fatty acid content. This technology, together with the solvent extraction of the dehydrated fruits, may have the potential to be a continuous, dry and clean technology for palm oil milling.
A review of the literature indicates that food scientists and health authorities in several countries, especially member countries of the European Union, are still very concerned about the potential health hazards of oxidized products and lipid polymers formed in repeatedly-used deep frying oils. During the frying process at temperatures of 170° – 200°C, steam formed from moisture in the food being fried help volatile products rise to the surface of the frying medium and into the kitchen atmosphere, imparting a mixture of fried-flavours and off-flavours. The non-volatile compounds formed, however, gradually build up in the oil as it is being repeatedly-used for food frying operations. These non-volatiles, primarily “polar compounds” (PC) and to a lesser extent lipid polymers, get absorbed into fried foods and eventually end up in our body system. Available local data suggests that deep-frying oil samples obtained from food hawkers and those produced under simulated deep-frying conditions in the laboratory, are generally safe as they contain PC within safe limits and rarely exceed the upper limit (UL) of 25%. This contrasts with the situation in some European countries where a very high proportion of frying oil samples collected from fast-food restaurants were reported to contain PC exceeding this UL. Appropriately, promotion of Hazard Analysis and Critical Control Points (HACCP) certification and gazetting of food regulations to limit the PC content in frying oils have been introduced in these countries to protect the health of consumers. Meanwhile, simple gadgets/test kits are available commercially to monitor the quality of the frying oil. This would greatly assist kitchen supervisors at restaurants and franchised friedfood outlets to know when best to change a batch of frying oil before the ULs of frying oil quality are breached.
Two hundred and sixty four samples of ready -to-eat foods (RTE) were obtained over a period of six months (April to September 2005) from 33 school hostel kitchens and canteens previously implicated in food poisoning outbreaks from 2000 to 2004. Sampling was done by food technologists and assistant environmental health ofhcers from various districts in Pahang while microbiological analysis was carried out at the Mentakab Food Quality Control Laboratory. The objective of the study was to obtain a comprehensive picture on the microbiological status of the foods that may have accounted for food poisoning outbreaks at school hostels and canteens in Pahang. Each food sample was analyzed for Total Plate Count (TPC), Salmonella, Coliform, Escheria coli, Staphylococcus aerus and Bacillus cereus. lt was found that none of the ready-to-eat foods sampled contained Salmonella although hve samples contained Bacillus cereus , four samples contained Staphylococcus aerus. High Coliform Counts were found in 15 food samples while Escheria coli was detected in two samples. Overall, it was found that 10.2 % of the samples had unsatisfactory counts.
Biotechnology-derived food crops are currently being developed in Malaysia mainly for disease resistance and improved post harvest quality. The modern biotechnology approach is adopted because of its potential to overcome constraints faced by conventional breeding techniques. Research on the development of biotechnology-derived papaya, pineapple, chili, passion fruit, and citrus is currently under way. Biotechnology-derived papaya developed for resistance to papaya ringspot virus (PRSV) and improved postharvest qualities is at the field evaluation stage. Pineapple developed for resistance to fruit black heart disorder is also being evaluated for proof-of-concept. Other biotechnology-derived food crops are at early stages of gene cloning and transformation. Activities and products involving biotechnology-derived crops will be fully regulated in the near future under the Malaysian Biosafety Law. At present they are governed only by guidelines formulated by the Genetic Modification Advisory Committee (GMAC), Malaysia. Commercialization of biotechnology-derived crops involves steps that require GMAC approval for all field evaluations and food-safety assessments before the products are placed on the market. Public acceptance of the biotechnology product is another important factor for successful commercialization. Understanding of biotechnology is generally low among Malaysians, which may lead to low acceptance of biotechnology-derived products. Initiatives are being taken by local organizations to improve public awareness and acceptance of biotechnology. Future research on plant biotechnology will focus on the development of nutritionally enhanced biotechnology-derived food crops that can provide more benefits to consumers.
Several million tones of palm oil and palm olein are used annually in the world for frying. This paper will discuss their frying performances in three major applications - industrial production of potato chips/crisps, industrial production of pre-fried frozen French fries and in fast food outlets. In the first study, about four tones of potato chips were continuously fried 8 hours a day and five days a week. The palm olein used (with proper management) performed well and was still in excellent condition and usable at the end of the trial. This was reflected in its low free fatty acid (FFA) content of around 0.23%, peroxide value of 4 meq/kg, anisidine value of 16, low polar and polymer contents of 10% and 2%, respectively, induction period (OSI) of 21 hours and high content of tocopehrols and tocotrienols of 530 ppm even after >1900 hours. In the second study in which an average 12 tones pre-fried frozen French fries were continuously fried a day for 5 days a week, palm oil performed excellently as reflected by its low FFA of 0.34%, food oil sensor reading of 1.1, low polar and polymer contents of 17% and 2.8%, respectively, over the 12 days of trial. In the third study in which palm shortening, palm oil and palm olein were simultaneously used to intermittently fry chicken parts in the laboratory simulating the conditions in fast food outlets, the three frying oils also performed very satisfactorily as reflected by their reasonably low FFA of <1%, smoke points of >180 degrees C, and polar and polymer contents of <25% and <6%, respectively, after 5 days of consecutive frying. All the quality indicators did not exceed the maximum discard points for frying oils/fats in the three applications, while the fried food product was well accepted by the in-house train sensory panel using a-nine point hedonic score.
Antioxidants are important inhibitory compounds against the oxidative deterioration of food. This study investigated the effects of various phytochemical antioxidant systems [oleoresin rosemary (OR), oleoresin sage (OS) and citric acid (CA)] on the physico-chemical characteristics of refined, bleached and deodorized (RBD) palm olein during the frying of potato chips. The effects of various mixtures of the antioxidants on the oil was also studied in repeated deep frying. The response surface methodology was used to optimize the composition of mixed antioxidants used. A comparative study was carried out with synthetic antioxidants. Samples of the oil after frying were analyzed for different physical and chemical properties. OR and OS were found to be effective phytochemical antioxidants protecting RBD palm olein against oxidative deterioration during frying.
Optimum processing conditions on palm oil-based formulations are required to produce the desired quality margarine. As oils and fats contribute to the overall property of the margarine, this paper will review the importance of beta' tending oils and fats in margarine formulation, effects of the processing parameters -- emulsion temperature, flow-rate, product temperature and pin-worker speed -- on palm oil margarines produced and their subsequent behaviour in storage. Palm oil, which contributes the beta' crystal polymorph and the best alternative to hydrogenated liquid fats, and the processing conditions can affect the margarine consistency by influencing the solid fat content (SFC) and the types of crystal polymorph formed during production as well as in storage. Palm oil, or hydrogenated palm oil and olein, in mixture with oils of beta tending, can veer the product to the beta' crystal form. However, merely having beta' crystal tending oils is not sufficient as the processing conditions are also important. The emulsion temperature had no significant effect on the consistency and polymorphic changes of the product during storage, even though differences were observed during processing. The consistency of margarine during storage was high at low emulsion flow-rates and low at high flow rates. The temperature of the scraped-surface tube-cooler is the most important parameter in margarine processing. High temperature will produce a hardened product with formation of beta-crystals during storage. The speed of the pin-worker is responsible for inducing crystallization but, at the same time, destroys the crystal agglomerates, resulting in melting.
Anhydrous milkfat (AMF) was fractionated to obtain a series of high-melting milkfat fractions (HMF). Solid fat content (SFC) of HMF as determined by nuclear magnetic resonance (NMR) was in the range 37.6-43.6% and 21.2-27.5% measured at 20 and 30 degrees C, respectively. The HMF have a higher melting characteristic compared to AMF as analyzed by differential scanning calorimetry (DSC) with melting enthalpies of 92.2-105.0 J/g and melting peak temperatures of 39.3-41.5 degrees C. The AMF was also blended with soft palm stearin (SPOs and/or hard palm stearin (HPOs)) according to a three conventional component mixture design which providing suitable formulations for HMF. This represented three selected blends of AMF:SPOs:HPOs at three different proportions (70:15:15, 60:30:10 and 50:45:5), having SFC and DSC melting characteristics of HMF. The study revealed that higher-melting characteristics of AMF could be achieved equally well by using both fractionation and blending techniques.
The characterization and fat migration of palm kernel stearin (PKS) and desiccated coconut, used as base filling centre in dark chocolate were studied. C36 and C38 triglycerides of PKS decreased by 11% and 9.6% respectively, whereas C32 and C34 increased by 97% and 48% respectively. The change in the triglycerides composition of PKS shift the melting point of PKS from 33.2 to 31.4 degrees C. Solid fat content (SFC) of PK reduced by 40% at 30 degrees C. The rate of fat migration was very slow at 18 degrees C storage compared to 30 degrees C. The rate of change of C36 in the chocolate layer was 0.1% week-1 and 1.2% week-1 at 18 and 30 degrees C respectively. Chocolate stored at 18 degrees C showed post hardening during storage period and withstood bloom during the storage period, whereas that stored at 30 degrees C became soft and bloomed faster after 3 weeks of storage.