The thermal conductivity of boron carbide filled thermoplastic natural rubber blend composite is studied experimentally as a function of filler loading and filler size. A polymer blend of 60/40 NR/HDPE was used as matrix for incorporation of particulate nano- and micro-sized B4C as filler to form the composite. As the filler loading is increased from 2-10%wt, a reduction and increment of thermal conductivity was observed. The results show at lower filler loading, HDPE crystallinity affects the thermal conductivity up to 4 and 6%wt of filler for nano- and micro-composite respectively. Further increase the loading do not much alter the crystallinity as the filler is distributed in continues phase of NR. The increment of filler amount in the amorphous NR causes the thermal conductivity to gradually increase which indicates the formation of interconnecting filler network structures
The adsorption equilibrium time and effects of pH and concentration of ¹⁴C-labeled chlorpyrifos
O,O-diethyl O-(3, 5, 6 trichloro-2-pyridyl)-phosphorothiote in soil were investigated. Two types of Malaysian soil under oil palm were used in this study; namely clay loam and clay soil obtained from the Sungai Sedu and Kuala Lumpur International Airport (KLIA) Estates, respectively. Equilibrium studies of chlorpyrifos between the agricultural soil and the pesticide solution were conducted. Adsorption equilibrium time was achieved within 6 and 24 hours for clay loam and clay soil, respectively. It was found that chlorpyrifos adsorbed by the soil samples was characterized by an initial rapid adsorption after which adsorption remained approximately constant. The percentage of ¹⁴C-labeled chlorpyrifos adsorption on soil was found to be higher in clay loam than in clay soils. Results of the study demonstrated that pH affected the adsorption of chlorpyrifos on both clay loam and clay soils. The adsorption of chlorpyrifos on both types of soil was higher at low pH with the adsorption reduced as the pH increased. Results also suggest that chlorpyrifos sorption by soil is concentration dependent.
The purpose of this study was to determine the adsorption coefficient (Koc) of chlorpyrifos in clay soil by measuring the Freundlich adsorption coefficient (Kads(f)) and desorption coefficient (1/n value) of chlorpyrifos. It was found that the Freundlich adsorption coefficient (Kads(f)) and the linear regression (r 2 ) of the Freundlich adsorption isotherm for chlorpyrifos in the clay soil were 52.6 L/kg and 0.5344, respectively. Adsoprtion equilibrium time was achieved within 24 hours for clay soil. This adsoprtion equilibrium time was used to determine the effect of concentration on adsorption. The adsorption coefficient (Koc) of clay soil was found to be 2783 L/kg with an initial concentration solution of 1 µg/g, soil-solution ratio (1:5) at 30 o C when the equilibrium between the soil matrix and solution was 24 hours. The Kdes decreased over four repetitions of the desorption process. The chlorpyrifos residues may be strongly adsorbed onto the surface of clay.
The microstructure, tensile fracture and creep fracture of as-cast beta phase contained γ-TiAl with nominal composition of Ti-48Al-4Cr (at.%) was investigated. The effect of beta phase on tensile and creep strength was determined from fracture analysis. Tensile test were performed at room temperature whereas constant load tensile creep test were performed at temperature 800 0 C and initial stress of 150MPa. Initial as-cast microstructure, microstructure and fracture surface after tensile and creep test were examined using scanning electron microscopy technique. Analysis shows brittle fracture after room temperature tensile test whereas ductile fracture after high temperature creep test. The role of beta phase was discussed. It is concluded that beta phase is sensitive to temperature and detrimental at both room and high temperature.
Electrodeposition of white copper-tin alloys (including white miralloys) has been done onto planar mild steel substrates from alkaline cyanide solutions at 65 0 C. The chemical composition of the coating is influenced by plating bath composition and current density. White miralloy can be produced from the test solution containing 10 g/l CuCN2 - , 45 g/l Na2SnO3, 25 g/l NaCN, and 12 g/l NaOH at current density about 5 mA/cm 2 . The local compositions of the coating cross section were analyzed using EDX installed in a FESEM operated at an accelerating voltage of 20 kV. The phases formed during co-deposition process were identified using XRD at 25 mA current and 35 kV voltage.
Heat treatment was introduced onto the aluminum coated low carbon steel to promote the formation of thin layer of oxide for enhancement of oxidation protection of steel. This process has transformed the existing intermetallic layer formed during hot dip aluminizing process. Experiment was conducted on the low carbon steel substrates with 10mm x 10mm x 2mm dimension. Hot dip aluminizing of low carbon steel was carried out at 750 ºC dipping temperature in a molten pure aluminum for 5 minutes. Aluminized samples were heat treated at 600 ºC, 700 ºC, 800 ºC, and 900 ºC for 1 hour. X-ray Diffraction (XRD), Scanning Electron Microscope (SEM) and EDAX were used in investigation. From the observation, it showed the intermetallic thickness increased with the increase in temperature. The result of EDAX analysis revealed the existence of oxide phase and the intermetallics. The XRD identified the intermetallics as Fe2Al5 and FeAl3.
Even though a lot of new advanced materials have been developed nowadays, steel remains a major material in construction, automobiles, appliances, industrial machinery as well as in the nuclear industry. Due to steel easily corroded, a proper surface protection is required to avoid any failures and extended the life cycle of the components. Surface coating is an efficient and economical method to obtain desirable material surfaces properties. Hot dip aluminizing technique was utilized in this study. Experiments have been conducted on the mild steel substrates with 12mm diameter. Prior to hot dipping process, observation on grain growth at three different temperatures had also been conducted to understand the behaviour of steel under application of heat. The substrates were heated at 700ºC, 800ºC and 900ºC for 1 hour and the microstructure was analyzed. The temperature of 800C was chosen for hot dipping. The substrates were dipped into the molten aluminum maintained at temperature 800ºC for 2,4,6,8,10,15 and 20 minutes. Optical microscopy and energy dispersive X-ray spectroscopy were used in this investigation. From the microstructure observation, it showed the appearance of intermetallic layer covered by the top layer of Al on the mild steel substrate increased with the increase in dipping time ranging from 36 to 282μm. The result of EDX analysis revealed the existence of Fe and Al in form of Fe2Al5 phase for all the dipping time.
One-dimensional nanostructure materials are very attractive because of their electronic and optical properties depending on their size. It is well known that properties of material can be tuned by reducing size to nanoscale because at the small sizes, that they behave differently with its bulk materials and the band gap will control by the size. The tunability of the band gap makes nanostructured materials useful for many applications. As one of the wide band gaps semiconductor compounds, zinc selenide (ZnSe) nanostructures (nanoparticles, nanowires, nanorods) have received much attention for the application in optoelectronic devices, such as blue laser diode, light emitting diodes, solar cells and IR optical windows. In this study, ZnSe nanostructures have been synthesized by reduction process of zinc selenate using hydrazine hydrate (N2H4.2H2O). The reductive agent of hydrazine hydrate was added to the starting materials of zinc selenate were heat treated at 500 o C for 1 hour under argon flow to form onedimensional nanostructures. The SEM and TEM images show the formation of nanocompositelike structures, which some small nanobars and nanopellets stick to the rod. The x-ray diffraction and elemental composition analysis confirm the formation of mixture zinc oxide and zinc selenide phases.
P-type transparent conductive oxide of copper aluminum oxide (CuAlO2) thin films were prepared by using sol-gel method with nitrate solutions as starting precursor. Copper nitrate and aluminum nitrate were selected as raw materials that provide the copper and aluminum source. The CuAlO2 thin films were deposited on pre-cleaned silicon substrate by spin-coating technique. To study of phase formation of CuAlO2, as prepared sample was dried and subjected to heat treatment at various temperatures. The heat-treated samples were characterized by x-ray diffraction (XRD) and energy dispersive x-ray (EDX). From XRD analysis result found that CuAlO2 phase was formed after annealing at 1100 o C for 4 hrs. EDX result of annealed sample at 1100 o C shows composition of Cu and Al that indicate the possibility of forming CuAlO2.
The specimens used were CaCO3 (Sigma Aldrich, purity 99.9 %). We have 23 parameters and 20 iterations, including two theta zero error, scale factor, thermal effect, coefficients for polynomial describing the background; U, V, W and mixing parameters of the profile peak function, lattice constants, positional parameters and overall isotropic temperature factors. Most the samples show that the crystal structure are rhombohedral with lattice constants a = b = 4.981 Å, c = 17.044 Å and space group is R3C. The microstrain (K) and the particle size (V) of CaCO3 ceramic were calculated using 10 the full width at half maximum (FWHM) of diffraction peaks from (0 1 2), (1 0 4), (0 0 6), (1 1 0), (1 1 3), (2 0 2), (0 1 8), (1 1 6), (2 2 1 ), (1 2 2) crystal planes are 2.1 x 10-2 and
362 nm, respectively.
Ceramic of BaxSr1-xTiO3 (BST) for x =0.3; 0.5 and 0.7 were successfully deposited by solid solution method. The BST ceramic were analyzed by x-ray diffraction (XRD). The XRD spectra was recorded on a Philips type PW 3701 diffractometer using CuKD (Oco = 1.54056 Å) radiation at 30 KV and 30 mA (900 watt). The spectra shows that BST ceramic are polycrystalline with tetragonal structure. The lattice constants analysis of the grown ceramics was analyzed by visual basic program. Using Cohen’s and Cramer’s algorithms in visual basic program, , the lattice constants are a = b = 3.877 Å; c = 3.970 Å for Ba0.3Sr0.7TiO3 ceramic, a = b = 3.979 Å; c = 3.981 Å. for Ba0.5Sr0.5TiO3 ceramic and a = b = 3.965 Å; c = 4.005 Å for Ba0.7Sr0.3TiO3 ceramic, respectively. The reform value of the lattice constant of BST ceramic is possibly associated with the anti site defects of Ba and Sr.
Effects of organoclay concentration on the properties of radiation crosslinked natural rubber (NR)/ ethylene vinyl acetate (EVA)/clay nanocomposites were investigated. The NR/EVA blend with a ratio of 40/60 was melt blended with different concentration of either dodecyl ammonium montmorillonite (DDA-MMT) or dimethyl dihydrogenated tallow quarternary ammonium montmorillonite (C20A). Composite of NR/EVA blend with unmodified clay (Na-MMT) was also prepared for comparison purposes. The composites were irradiated with electron beam (EB) at an optimum irradiation dose. The formation of radiation-induced crosslinking depends on the type and concentration of the organoclay used in the preparation of nanocomposites as measured by gel content. Changes in the interlayer distance of the silicate layers with the increase of organoclay concentration were shown by the XRD results. Variation in the tensile properties of the nanocomposites with the increase of organoclay concentration depends on the formation of crosslinking as well as reinforcement effect of the organoclay. Improvement in thermal stability of the NR/EVA blend was also observed with the presence of organoclay.
A Monte Carlo simulation of the Malaysian nuclear reactor has been performed using MCNP Version 5 code. The purpose of the work is the determination of the multiplication factor (k eff ) for TRIGA Mark II research reactor in Malaysia based on Monte Carlo method. This work has been performed to calculate the value of k eff for two cases, which are the control rod either fully withdrawn or fully inserted to construct a complete model of the TRIGA Mark II PUSPATI Reactor (RTP). The RTP core was modeled as close as possible to the real core and the results of k eff from MCNP5 were obtained. When the control-fuel rods were fully inserted, the k eff value indicates the RTP reactor was in the subcritical condition with a value of 0.98370 ± 0.00054. When the control-fuel rods were fully withdrawn the value of k eff value indicates the RTP reactor is in the supercritical condition, that is 1.10773 ± 0.00083.
New solid acid catalyst consisting of zirconium sulfate (ZS) supported on a pure-HMS hexagonal mesoporous material (HMS) have been prepared and characterized. This heterogeneous catalyst is able to make a contribution to the field of acid catalyst involving bulky organic molecules. XRD analysis shows that ZS is intact after impregnated on HMS surface and formed finely dispersed species. No ZS crystal phase was developed even at ZS loadings as high as 40 wt %. The occurrence of chemical interaction between ZS and HMS was observed by XPS analysis. Further, XRF results demonstrated that there is no leaching of ZS elements after impregnation. This study shows that ZS can be impregnated on HMS and would be a promising solid acid catalyst for acid-type reactions espcially invovling bulky organic molecuels.
Structural and dielectric properties of barium strontium, titanate (Ba(ÿ)SrxTiO$) ceramics with x—
0.25, 0.5 and 0.75 were investigated. The Ba(i-xjSrxTiOs ceramics were synthesised by solid state
reaction method. Microstructure, surface morphology and dielectric properties of the synthesised
ceramics were examined using XRD, SEM and Impedance Spectroscopy respectively. XRD results
revealed that all samples contained BaTiOg as primary phase with tetragonal perovskite crystal
structure. The crystallite size slightly increased with the increasing of Sr contents. SEM micrographs
showed that the microstructure become denser when Sr contents increased. Impedance spectroscopy
showed dielectric constant for all samples were decreased with increasing temperature up to 200°C.
Dielectric material CaCu3Ti4O12 (CCTO) prepared by solid state technique, was calcined at different temperatures (700 - 1000 o C) for 6 and 12 hours. The calcined powder were analysed by XRD to identify the CCTO formation. Then the microstructure was observed by SEM. The CCTO single phase formation was firstly detected on sample calcined at 700 o C for 12 hours. The microstructure obtained shows the particles were spherical in shape. The grain getting larger as calcination temperature was increased.
An experimental study of the field emission from nitrogen doped Diamond-Like-Carbon (DLC) thin films prepared by plasma Chemical Vapor Deposition (CVD) was carried out for the purpose of investigating the characteristic of field electron emission from the surface of nitrogen doped DLC thin film. Thin DLC film was deposited on silicon using the plasma CVD method, from a mixture of Methane (CH4), Helium (He) and Nitrogen (N2) at room temperature. Emission current was measured while high volume of voltage was applied between the cathode-anode diode structures. Barrier height was obtained by current density-electric field (J-E) characteristic in the relation of Fowler-Nordheim equation. The value of barrier height in range of 0.03eV to 0.06eV was obtained and considered as low barrier.
Developments of computer technology and image processing have shifted conventional industrial radiography application to industrial digital radiography (IDR) system. In this study, two types of IDR modules for non destructive testing (NDT), namely drum- and laser- type film digitizer with 50 μm pixel pitch have been evaluated for NDT applications. The modulation transfer function (MTF) and noise power spectrum (NPS) measurement were adapted to evaluate the image quality of IDR images. Results shown the averaged MTF for drum- and laser- type film digitizer at 20% modulation were 6.15 cycles/mm and 6.55 cycles/mm respectively. For NPS measurement and calculation, the result obtained shows that drum type film digitizer produced higher noise then laser type film digitizer. The study shows that the laser type film digitizer is the best system to be used for film digitization purposes because the MTF result shows that it modulates better than drum type and has the lowest and stable NPS.
Fly ash is the finely divided mineral residue resulting from the combustion of coal in electric generating plants. Fly ash consists of inorganic, incombustible matter present in the coal that has been fused during combustion into a glassy, amorphous structure. Fly ash particles are generally spherical in shape and range in size from 2 μm to 10 μm. They consist mostly of silicon dioxide (SiO2), aluminium oxide (Al2O3) and iron oxide (Fe2O3). Fly ash like soil contains trace concentrations of the following heavy metals: nickel, vanadium, cadmium, barium, chromium, copper, molybdenum, zinc and lead. The chemical compositions of the sample have been examined and the fly ash are of ASTM C618 Class F.
Radiotherapy causes various complications including low immunity. Past research has shown that the low immunity is due to the low amount of lymphocytes and consumption of citrullus vulgaris will alleviate this problem. Based on this a study was conducted to identify how citrullus vulgaris was able to produce radioprotection on the lymphocyte membrane. A total of 30 adult male Sprague-Dawley rats were used and divided into three equals groups of positive control, negative control and treatment. For seven days, positive control and negative control were force fed with normal saline of 40 ml/kg animal weight while the treatment group received 40 g/kg animal weight fresh juice of citrullus vulgaris daily. After a week positive control and treatment group were irradiated with 0.9 Gy gamma ray. Viable lymphocyte were determined using propidium iodine and acridine orange stain. Results clearly shows that positive control, negative and treatment group were significantly different at 34 3% , 80 2% and 71 2% respectively. SEM results shows that pores were present on the membrane of the positive control while the negative control had none. Similar results were also found on the treatment group. Based on the result it had shown that citrullus vulgaris had radioprotection properties and lymphocytes were destroyed by the formation of pores on their membrane. It is very likely that the radioprotection properties could be due to the presence of antioxidants particularly vitamin A, C and lycopene. In conclusion, citrullus vulgaris could be used as a safe radioprotection agent.