MyMedR

Displaying publications 41 - 60 of 139 in total

Abstract:

Sort:

Finite element study of functionally graded porous femoral stems incorporating body-centered cubic structure

Alkhatib SE, Tarlochan F, Mehboob H, Singh R, Kadirgama K, Harun WSBW

Artif Organs, 2019 Jul;43(7):E152-E164.
PMID: 30805945 DOI: 10.1111/aor.13444

The mismatch between stiffness of the femoral dense stem and host bone causes complications to patients, such as aseptic loosening and bone resorption. Three-dimensional finite-element models of homogeneous porous (HGP) and functionally graded porous (FGP) stems incorporating body-centered cubic (BCC) structures are proposed in this article as an alternative to the dense stems. The relationship between the porosity and strut thickness of the BCC structure was developed to construct the finite-element models. Three levels of porosities (20%, 50%, and 80%) were modeled in HGP and FGP stems. The porosity of the stems was decreased distally according to the sigmoid function (n = 0.1, n = 1 and n = 10) with 3 grading exponents. The results showed that FGP stems transferred 120%-170% higher stresses to the femur (Gruen zone 7) as compared to the solid stem. Conversely, the stresses in HGP and FGP stems were 12%-34% lower than the dense stem. The highest micromotions (105-147 µm) were observed for stems of 80% overall porosity, and the lowest (42-46 µm) was for stems of 20% overall porosity. Finally, FGP stems with a grading exponent of n = 10 resulted in an 11%-28% reduction in micromotions.

Matched MeSH terms: Finite Element Analysis
Extracellular matrix integrity affects the mechanical behaviour of in-situ chondrocytes under compression

Moo EK, Han SK, Federico S, Sibole SC, Jinha A, Abu Osman NA, et al.

J Biomech, 2014 Mar 21;47(5):1004-13.
PMID: 24480705 DOI: 10.1016/j.jbiomech.2014.01.003

Cartilage lesions change the microenvironment of cells and may accelerate cartilage degradation through catabolic responses from chondrocytes. In this study, we investigated the effects of structural integrity of the extracellular matrix (ECM) on chondrocytes by comparing the mechanics of cells surrounded by an intact ECM with cells close to a cartilage lesion using experimental and numerical methods. Experimentally, 15% nominal compression was applied to bovine cartilage tissues using a light-transmissible compression system. Target cells in the intact ECM and near lesions were imaged by dual-photon microscopy. Changes in cell morphology (N(cell)=32 for both ECM conditions) were quantified. A two-scale (tissue level and cell level) Finite Element (FE) model was also developed. A 15% nominal compression was applied to a non-linear, biphasic tissue model with the corresponding cell level models studied at different radial locations from the centre of the sample in the transient phase and at steady state. We studied the Green-Lagrange strains in the tissue and cells. Experimental and theoretical results indicated that cells near lesions deform less axially than chondrocytes in the intact ECM at steady state. However, cells near lesions experienced large tensile strains in the principal height direction, which are likely associated with non-uniform tissue radial bulging. Previous experiments showed that tensile strains of high magnitude cause an up-regulation of digestive enzyme gene expressions. Therefore, we propose that cartilage degradation near tissue lesions may be due to the large tensile strains in the principal height direction applied to cells, thus leading to an up-regulation of catabolic factors.

Matched MeSH terms: Finite Element Analysis
Fulltext Biomechanical Stress in Obturator Prostheses: A Systematic Review of Finite Element Studies

Mousa MA, Abdullah JY, Jamayet NB, Alam MK, Husein A

Biomed Res Int, 2021;2021:6419774.
PMID: 34447852 DOI: 10.1155/2021/6419774

Aim: This systematic review is aimed at investigating the biomechanical stress that develops in the maxillofacial prostheses (MFP) and supporting structures and methods to optimize it. Design and Methods. A literature survey was conducted for full-text English articles which used FEA to examine the stress developed in conventional and implant-assisted MFPs from January 2010 to December 2020.
Results: 87 articles were screened to get an update on the desired information. 74 were excluded based on a complete screening, and finally, 13 articles were recruited for complete reviewing. Discussion. The MFP is subjected to stress, which is reflected in the form of compressive and tensile strengths. The stress is mainly concentrated the resection line and around the apices of roots of teeth next to the defect. Diversity of designs and techniques were introduced to optimize the stress distribution, such as modification of the clasp design, using materials with different mechanical properties for dentures base and retainer, use of dental (DI) and/or zygomatic implants (ZI), and free flap reconstruction before prosthetic rehabilitation.
Conclusion: Using ZI in the defective side of the dentulous maxillary defect and defective and nondefective side of the edentulous maxillary defect was found more advantageous, in terms of compression and tensile stress and retention, when compared with DI and free flap reconstruction.

Matched MeSH terms: Finite Element Analysis
Fulltext FEM Analysis of Sezawa Mode SAW Sensor for VOC Based on CMOS Compatible AlN/SiO₂/Si Multilayer Structure

Aslam MZ, Jeoti V, Karuppanan S, Malik AF, Iqbal A

Sensors (Basel), 2018 May 24;18(6).
PMID: 29882929 DOI: 10.3390/s18061687

A Finite Element Method (FEM) simulation study is conducted, aiming to scrutinize the sensitivity of Sezawa wave mode in a multilayer AlN/SiO₂/Si Surface Acoustic Wave (SAW) sensor to low concentrations of Volatile Organic Compounds (VOCs), that is, trichloromethane, trichloroethylene, carbon tetrachloride and tetrachloroethene. A Complimentary Metal-Oxide Semiconductor (CMOS) compatible AlN/SiO₂/Si based multilayer SAW resonator structure is taken into account for this purpose. In this study, first, the influence of AlN and SiO₂ layers’ thicknesses over phase velocities and electromechanical coupling coefficients (k²) of two SAW modes (i.e., Rayleigh and Sezawa) is analyzed and the optimal thicknesses of AlN and SiO₂ layers are opted for best propagation characteristics. Next, the study is further extended to analyze the mass loading effect on resonance frequencies of SAW modes by coating a thin Polyisobutylene (PIB) polymer film over the AlN surface. Finally, the sensitivity of the two SAW modes is examined for VOCs. This study concluded that the sensitivity of Sezawa wave mode for 1 ppm of selected volatile organic gases is twice that of the Rayleigh wave mode.

Matched MeSH terms: Finite Element Analysis
Fulltext Finite element simulation of takraw balls and their impact on a flat surface

Norhafizan Ahmad, Zahari Taha, Tuan Mohammad Yusoff Shah Tuan Ya, Iskandar Hasanuddin

Movement Health & Exercise, 2012;1(1):1-9.
MyJurnal

The takraw ball is a very unique interwoven ball used in the action game of sepak takraw. The traditional takraw ball is manufactured by conventionally weaving split rattan strips into a spherical basket. Modern takraw balls are manufactured by forming strips of plastics materials into interwoven hoop. These interwoven hoops form 12 pentagon holes and 30 intersections. The purpose of this study is to construct a finite-element (FE) model of a takraw ball in particular for normal impact simulation on flat surfaces under low speed conditions. Two FE models were developed to observe the dynamic behavior including impact forces, contact time, coefficient of restitution and deformation of the ball. The first model consists of a single solid hollow ball with 12 pentagon holes and the second model consists of six center strips and 12 side edge strips of
extrusion hoops to form 12 pentagon holes and 270 cross-sections. The models were also compared with results of experimental impact tests whereby the ball was impacted normal to a rigid plate at three different heights. The ball is described in the FE model as a linear elastic material.
It was found that the FE analysis solution of the ball model was found to be reasonably close with the experimental results. However further improvement need to be done by taking into consideration the nonlinearity of the takraw ball under large deformation as well as at high impact velocity.

Matched MeSH terms: Finite Element Analysis
Fulltext Seismic response of a light rail transit station equipped with braced viscous damper

Fateh, A., Hejazi, F., Ramanathan, R.A., Jaffar, M.S.

Pertanika Journal of Science & Technology, 2016;24(2):273-283.
MyJurnal

The use of the Light Rail Transit (LRT) system is currently preferred because LRT is sustainable,
improves travel options and facilitates swift mobility in urban areas. Hence, the structural stability
and safety of this public transportation system against seismic occurrences are indispensable. Given
that these structures cannot be considered conventional frames because of their complex architectural
design, focussing meticulously on reliable seismic design codes and structural rehabilitation techniques
is vital for the design of the lateral resistance system. One Malaysian LRT station is considered in this
study, and the seismic response of this train station when equipped with supplementary viscous damper
devices is evaluated. Thus, the LRT station is modelled through finite element simulation. The methods
of seismic analysis are limited to linear seismic analyses, namely, response spectrum and time history
analyses. Results derived in this study show a significant improvement in structural response when the
station is fitted with dampers; approximately 40% reduction in displacement is observed at the top joint
of the roof. Furthermore, the lateral base shears decrease by approximately 70%.

Matched MeSH terms: Finite Element Analysis
The influence of experimental silane primers on dentin bond strength and morphology: a laboratory and finite element analysis study

Mustafa AA, Matinlinna JP, Saidin S, Kadir MR

J Prosthet Dent, 2014 Dec;112(6):1498-506.
PMID: 24993375 DOI: 10.1016/j.prosdent.2014.05.011

STATEMENT OF PROBLEM: The inconsistency of dentin bonding affects retention and microleakage.
PURPOSE: The purpose of this laboratory and finite element analysis study was to investigate the effects on the formation of a hybrid layer of an experimental silane coupling agent containing primer solutions composed of different percentages of hydroxyethyl methacrylate.
MATERIAL AND METHODS: A total of 125 sound human premolars were restored in vitro. Simple class I cavities were formed on each tooth, followed by the application of different compositions of experimental silane primers (0%, 5%, 25%, and 50% of hydroxyethyl methacrylate), bonding agents, and dental composite resins. Bond strength tests and scanning electron microscopy analyses were performed. The laboratory experimental results were validated with finite element analysis to determine the pattern of stress distribution. Simulations were conducted by placing the restorative composite resin in a premolar tooth by imitating simple class I cavities. The laboratory and finite element analysis data were significantly different from each other, as determined by 1-way ANOVA. A post hoc analysis was conducted on the bond strength data to further clarify the effects of silane primers.
RESULTS: The strongest bond of hybrid layer (16.96 MPa) was found in the primer with 25% hydroxyethyl methacrylate, suggesting a barely visible hybrid layer barrier. The control specimens without the application of the primer and the primer specimens with no hydroxyethyl methacrylate exhibited the lowest strength values (8.30 MPa and 11.78 MPa) with intermittent and low visibility of the hybrid layer. These results were supported by finite element analysis that suggested an evenly distributed stress on the model with 25% hydroxyethyl methacrylate.
CONCLUSIONS: Different compositions of experimental silane primers affected the formation of the hybrid layer and its resulting bond strength.

Matched MeSH terms: Finite Element Analysis
Biomechanical features of six design of the delta external fixator for treating Pilon fracture: a finite element study

Ramlee MH, Sulong MA, Garcia-Nieto E, Penaranda DA, Felip AR, Kadir MRA

Med Biol Eng Comput, 2018 Oct;56(10):1925-1938.
PMID: 29679256 DOI: 10.1007/s11517-018-1830-3

Pilon fractures can be caused by high-energy vertical forces which may result in long-term patient immobilization. Many experts in orthopedic surgery recommend the use of a Delta external fixator for type III Pilon fracture treatment. This device can promote immediate healing of fractured bone, minimizing the rate of complications as well as allowing early mobilization. The characteristics of different types of the Delta frame have not been demonstrated yet. By using the finite element method, this study was conducted to determine the biomechanical characteristics of six different configurations (Model 1 until Model 6). CT images from the lower limb of a healthy human were used to reconstruct three-dimensional models of foot and ankle bones. All bones were assigned with isotropic material properties and the cartilages were assigned to exhibit hyperelasticity. A linear link was used to simulate 37 ligaments at the ankle joint. Axial loads of 70 and 350 N were applied at the proximal tibia to simulate the stance and swing phase. The metatarsals and calcaneus were fixed distally in order to prevent rigid body motion. A synthetic ankle bone was used to validate the finite element model. The simulated results showed that Delta3 produced the highest relative micromovement (0.09 mm, 7 μm) during the stance and swing phase, respectively. The highest equivalent von Mises stress was found at the calcaneus pin of the Delta4 (423.2 MPa) as compared to others. In conclusion, Delta1 external fixator was the most favorable option for type III Pilon fracture treatment. Graphical abstract ᅟ.

Matched MeSH terms: Finite Element Analysis*
In silico study of glenoid perforation during total shoulder arthroplasty: the effects on stress & micromotion

Wahab AHA, Saad APM, Syahrom A, Kadir MRA

Comput Methods Biomech Biomed Engin, 2020 Apr;23(5):182-190.
PMID: 31910663 DOI: 10.1080/10255842.2019.1709828

Glenoid perforation is not the intended consequence of the surgery and must be avoided. The analysis on biomechanical aspect of glenoid vault perforation remains unknown. The purpose of this study is to determine the impact of glenoid perforation towards stress distribution and micromotion at the interfaces. Eight glenoid implant models had been constructed with various size, number and type of fixation. A load of 750 N was applied to centre, superior-anterior and superior-posterior area. Implant perforation had minimal impact on stress distribution and micromotion at the interfaces. However, cement survival rate for implant without perforation was the highest with a difference of up to 37% compared to other perforated models. Besides that, implant fixation and high stresses at the implant had more of an impact on implant instability than implant perforation. As a conclusion, glenoid perforation did not influence the stress distribution and micromotion, but, it reduced cement survival rate and increase the stress critical volume.

Matched MeSH terms: Finite Element Analysis
Fulltext A novel design, analysis and 3D printing of Ti-6Al-4V alloy bio-inspired porous femoral stem

Mehboob H, Tarlochan F, Mehboob A, Chang SH, Ramesh S, Harun WSW, et al.

J Mater Sci Mater Med, 2020 Aug 20;31(9):78.
PMID: 32816091 DOI: 10.1007/s10856-020-06420-7

The current study is proposing a design envelope for porous Ti-6Al-4V alloy femoral stems to survive under fatigue loads. Numerical computational analysis of these stems with a body-centered-cube (BCC) structure is conducted in ABAQUS. Femoral stems without shell and with various outer dense shell thicknesses (0.5, 1.0, 1.5, and 2 mm) and inner cores (porosities of 90, 77, 63, 47, 30, and 18%) are analyzed. A design space (envelope) is derived by using stem stiffnesses close to that of the femur bone, maximum fatigue stresses of 0.3σys in the porous part, and endurance limits of the dense part of the stems. The Soderberg approach is successfully employed to compute the factor of safety Nf > 1.1. Fully porous stems without dense shells are concluded to fail under fatigue load. It is thus safe to use the porous stems with a shell thickness of 1.5 and 2 mm for all porosities (18-90%), 1 mm shell with 18 and 30% porosities, and 0.5 mm shell with 18% porosity. The reduction in stress shielding was achieved by 28%. Porous stems incorporated BCC structures with dense shells and beads were successfully printed.

Matched MeSH terms: Finite Element Analysis
Computational local stiffness analysis of biological cell: High aspect ratio single wall carbon nanotube tip

TermehYousefi A, Bagheri S, Shahnazar S, Rahman MH, Kadri NA

Mater Sci Eng C Mater Biol Appl, 2016 Feb;59:636-642.
PMID: 26652417 DOI: 10.1016/j.msec.2015.10.041

Carbon nanotubes (CNTs) are potentially ideal tips for atomic force microscopy (AFM) due to the robust mechanical properties, nanoscale diameter and also their ability to be functionalized by chemical and biological components at the tip ends. This contribution develops the idea of using CNTs as an AFM tip in computational analysis of the biological cells. The proposed software was ABAQUS 6.13 CAE/CEL provided by Dassault Systems, which is a powerful finite element (FE) tool to perform the numerical analysis and visualize the interactions between proposed tip and membrane of the cell. Finite element analysis employed for each section and displacement of the nodes located in the contact area was monitored by using an output database (ODB). Mooney-Rivlin hyperelastic model of the cell allows the simulation to obtain a new method for estimating the stiffness and spring constant of the cell. Stress and strain curve indicates the yield stress point which defines as a vertical stress and plan stress. Spring constant of the cell and the local stiffness was measured as well as the applied force of CNT-AFM tip on the contact area of the cell. This reliable integration of CNT-AFM tip process provides a new class of high performance nanoprobes for single biological cell analysis.

Matched MeSH terms: Finite Element Analysis
Biomechanical analysis of the wrist arthroplasty in rheumatoid arthritis: a finite element analysis

Bajuri MN, Abdul Kadir MR, Murali MR, Kamarul T

Med Biol Eng Comput, 2013 Feb;51(1-2):175-86.
PMID: 23124814 DOI: 10.1007/s11517-012-0982-9

The total replacement of wrists affected by rheumatoid arthritis (RA) has had mixed outcomes in terms of failure rates. This study was therefore conducted to analyse the biomechanics of wrist arthroplasty using recently reported implants that have shown encouraging results with the aim of providing some insights for the future development of wrist implants. A model of a healthy wrist was developed using computed tomography images from a healthy volunteer. An RA model was simulated based on all ten general characteristics of the disease. The ReMotion ™ total wrist system was then modelled to simulate total wrist arthroplasty (TWA). Finite element analysis was performed with loads simulating the static hand grip action. The results show that the RA model produced distorted patterns of stress distribution with tenfold higher contact pressure than the healthy model. For the TWA model, contact pressure was found to be approximately fivefold lower than the RA model. Compared to the healthy model, significant improvements were observed for the TWA model with minor variations in the stress distribution. In conclusion, the modelled TWA reduced contact pressure between bones but did not restore the stress distribution to the normal healthy condition.

Matched MeSH terms: Finite Element Analysis*
Finite element analysis of Puddu and Tomofix plate fixation for open wedge high tibial osteotomy

Raja Izaham RM, Abdul Kadir MR, Abdul Rashid AH, Hossain MG, Kamarul T

Injury, 2012 Jun;43(6):898-902.
PMID: 22204773 DOI: 10.1016/j.injury.2011.12.006

The use of open wedge high tibial osteotomy (HTO) to correct varus deformity of the knee is well established. However, the stability of the various implants used in this procedure has not been previously demonstrated. In this study, the two most common types of plates were analysed (1) the Puddu plates that use the dynamic compression plate (DCP) concept, and (2) the Tomofix plate that uses the locking compression plate (LCP) concept. Three dimensional model of the tibia was reconstructed from computed tomography images obtained from the Medical Implant Technology Group datasets. Osteotomy and fixation models were simulated through computational processing. Simulated loading was applied at 60:40 ratios on the medial:lateral aspect during single limb stance. The model was fixed distally in all degrees of freedom. Simulated data generated from the micromotions, displacement and, implant stress were captured. At the prescribed loads, a higher displacement of 3.25 mm was observed for the Puddu plate model (p<0.001). Coincidentally the amount of stresses subjected to this plate, 24.7 MPa, was also significantly lower (p<0.001). There was significant negative correlation (p<0.001) between implant stresses to that of the amount of fracture displacement which signifies a less stable fixation using Puddu plates. In conclusion, this study demonstrates that the Tomofix plate produces superior stability for bony fixation in HTO procedures.

Matched MeSH terms: Finite Element Analysis*
Fulltext The use of X-shaped cross-link in posterior spinal constructs improves stability in thoracolumbar burst fracture: a finite element analysis

Alizadeh M, Kadir MR, Fadhli MM, Fallahiarezoodar A, Azmi B, Murali MR, et al.

J Orthop Res, 2013 Sep;31(9):1447-54.
PMID: 23640802 DOI: 10.1002/jor.22376

Posterior instrumentation is a common fixation method used to treat thoracolumbar burst fractures. However, the role of different cross-link configurations in improving fixation stability in these fractures has not been established. A 3D finite element model of T11-L3 was used to investigate the biomechanical behavior of short (2 level) and long (4 level) segmental spine pedicle screw fixation with various cross-links to treat a hypothetical L1 vertebra burst fracture. Three types of cross-link configurations with an applied moment of 7.5 Nm and 200 N axial force were evaluated. The long construct was stiffer than the short construct irrespective of whether the cross-links were used (p < 0.05). The short constructs showed no significant differences between the cross-link configurations. The XL cross-link provided the highest stiffness and was 14.9% stiffer than the one without a cross-link. The long construct resulted in reduced stress to the adjacent vertebral bodies and screw necks, with 66.7% reduction in bending stress on L2 when the XL cross-link was used. Thus, the stability for L1 burst fracture fixation was best achieved by using long segmental posterior instrumentation constructs and an XL cross-link configuration. Cross-links did not improved stability when a short structure was used.

Matched MeSH terms: Finite Element Analysis
Finite element analysis of three commonly used external fixation devices for treating Type III pilon fractures

Ramlee MH, Kadir MR, Murali MR, Kamarul T

Med Eng Phys, 2014 Oct;36(10):1322-30.
PMID: 25127377 DOI: 10.1016/j.medengphy.2014.05.015

Pilon fractures are commonly caused by high energy trauma and can result in long-term immobilization of patients. The use of an external fixator i.e. the (1) Delta, (2) Mitkovic or (3) Unilateral frame for treating type III pilon fractures is generally recommended by many experts owing to the stability provided by these constructs. This allows this type of fracture to heal quickly whilst permitting early mobilization. However, the stability of one fixator over the other has not been previously demonstrated. This study was conducted to determine the biomechanical stability of these external fixators in type III pilon fractures using finite element modelling. Three-dimensional models of the tibia, fibula, talus, calcaneus, navicular, cuboid, three cuneiforms and five metatarsal bones were reconstructed from previously obtained CT datasets. Bones were assigned with isotropic material properties, while the cartilage was assigned as hyperelastic springs with Mooney-Rivlin properties. Axial loads of 350 N and 70 N were applied at the tibia to simulate the stance and the swing phase of a gait cycle. To prevent rigid body motion, the calcaneus and metatarsals were fixed distally in all degrees of freedom. The results indicate that the model with the Delta frame produced the lowest relative micromovement (0.03 mm) compared to the Mitkovic (0.05 mm) and Unilateral (0.42 mm) fixators during the stance phase. The highest stress concentrations were found at the pin of the Unilateral external fixator (509.2 MPa) compared to the Mitkovic (286.0 MPa) and the Delta (266.7 MPa) frames. In conclusion, the Delta external fixator was found to be the most stable external fixator for treating type III pilon fractures.

Matched MeSH terms: Finite Element Analysis*
Biomechanical evaluation of two commonly used external fixators in the treatment of open subtalar dislocation--a finite element analysis

Ramlee MH, Kadir MR, Murali MR, Kamarul T

Med Eng Phys, 2014 Oct;36(10):1358-66.
PMID: 25092623 DOI: 10.1016/j.medengphy.2014.07.001

Subtalar dislocation is a rare injury caused by high-energy trauma. Current treatment strategies include leg casts, internal fixation and external fixation. Among these, external fixators are the most commonly used as this method is believed to provide better stabilization. However, the biomechanical stability provided by these fixators has not been demonstrated. This biomechanical study compares two commonly used external fixators, i.e. Mitkovic and Delta. CT imaging data were used to reconstruct three-dimensional models of the tibia, fibula, talus, calcaneus, navicular, cuboid, three cuneiforms and five metatarsal bones. The 3D models of the bones and cartilages were then converted into four-noded linear tetrahedral elements, whilst the ligaments were modelled with linear spring elements. Bones and cartilage were idealized as homogeneous, isotropic and linear. To simulate loading during walking, axial loading (70 N during the swing and 350 N during the stance phase) was applied at the end of diaphyseal tibia. The results demonstrate that the Mitkovic fixator produced greater displacement (peak 3.0mm and 15.6mm) compared to the Delta fixator (peak 0.8mm and 3.9 mm), in both the swing and stance phase, respectively. This study demonstrates that the Delta external fixator provides superior stability over the Mitkovic fixator. The Delta fixator may be more effective in treating subtalar dislocation.

Matched MeSH terms: Finite Element Analysis*
Mechanical and functional assessment of the wrist affected by rheumatoid arthritis: A finite element analysis

Bajuri MN, Kadir MR, Raman MM, Kamarul T

Med Eng Phys, 2012 Nov;34(9):1294-302.
PMID: 22277308 DOI: 10.1016/j.medengphy.2011.12.020

Understanding the pathomechanics involved in rheumatoid arthritis (RA) of the wrist provides valuable information, which will invariably allow various therapeutic possibilities to be explored. The computational modelling of this disease permits the appropriate simulation to be conducted seamlessly. A study that underpins the fundamental concept that produces the biomechanical changes in a rheumatoid wrist was thus conducted through the use of finite element method. The RA model was constructed from computed tomography datasets, taking into account three major characteristics: synovial proliferation, cartilage destruction and ligamentous laxity. As control, a healthy wrist joint model was developed in parallel and compared. Cartilage was modelled based on the shape of the articulation while the ligaments were modelled with linear spring elements. A load-controlled analysis was performed simulating physiological hand grip loading conditions. The results demonstrated that the diseased model produced abnormal wrist extension and stress distribution as compared to the healthy wrist model. Due to the weakening of the ligaments, destruction of the cartilage and lower bone density, the altered biomechanical stresses were particularly evident at the radioscaphoid and capitolunate articulations which correlate to clinical findings. These results demonstrate the robust finding of the developed RA wrist model, which accurately predicted the pathological process.

Matched MeSH terms: Finite Element Analysis*
Fulltext The Effects of Physiological Biomechanical Loading on Intradiscal Pressure and Annulus Stress in Lumbar Spine: A Finite Element Analysis

Zahari SN, Latif MJA, Rahim NRA, Kadir MRA, Kamarul T

J Healthc Eng, 2017;2017:9618940.
PMID: 29065672 DOI: 10.1155/2017/9618940

The present study was conducted to examine the effects of body weight on intradiscal pressure (IDP) and annulus stress of intervertebral discs at lumbar spine. Three-dimensional finite element model of osseoligamentous lumbar spine was developed subjected to follower load of 500 N, 800 N, and 1200 N which represent the loads for individuals who are normal and overweight with the pure moments at 7.5 Nm in flexion and extension motions. It was observed that the maximum IDP was 1.26 MPa at L1-L2 vertebral segment. However, the highest increment of IDP was found at L4-L5 segment where the IDP was increased to 30% in flexion and it was more severe at extension motion reaching to 80%. Furthermore, the maximum annulus stress also occurred at the L1-L2 segment with 3.9 MPa in extension motion. However, the highest increment was also found at L4-L5 where the annulus stress increased to 17% in extension motion. Based on these results, the increase of physiological loading could be an important factor to the increment of intradiscal pressure and annulus fibrosis stress at all intervertebral discs at the lumbar spine which may lead to early intervertebral disc damage.

Matched MeSH terms: Finite Element Analysis*
Finite element analysis of zygomatic implants in intrasinus and extramaxillary approaches for prosthetic rehabilitation in severely atrophic maxillae

Ishak MI, Kadir MR, Sulaiman E, Kasim NH

Int J Oral Maxillofac Implants, 2013 May-Jun;28(3):e151-60.
PMID: 23748334 DOI: 10.11607/jomi.2304

To compare the extramaxillary approach with the widely used intrasinus approach via finite element method.

Matched MeSH terms: Finite Element Analysis*
Analytical and computational sliding wear prediction in a novel knee implant: a case study

Hussin MS, Fernandez J, Ramezani M, Kumar P, Kelly PA

Comput Methods Biomech Biomed Engin, 2020 Mar;23(4):143-154.
PMID: 31928215 DOI: 10.1080/10255842.2019.1709118

Osteoarthritis (OA) is a commonly occurring cartilage degenerative disease. The end stage treatment is Total Knee Arthroplasty (TKA), which can be costly in terms of initial surgery, but also in terms of revision knee arthroplasty, which is quite often required. A novel conceptual knee implant has been proposed to function as a reducer of stress across the joint surface, to extend the period of time before TKA becomes necessary. The objective of this paper is to develop a computational model which can be used to assess the wear arising at the implant articulating surfaces. Experimental wear coefficients were determined from physical testing, the results of which were verified using a semi-analytical model. Experimental results were incorporated into an anatomically correct computational model of the knee and implant. The wear-rate predicted for the implant was 27.74 mm3 per million cycles (MC) and the wear depth predicted was 1.085 mm/MC. Whereas the wear-rate is comparable to that seen in conventional knee implants, the wear depth is significantly higher than for conventional knee prostheses, and indicates that, in order to be viable, wear-rates should be reduced in some way, perhaps by using low-wear polymers.

Matched MeSH terms: Finite Element Analysis

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links