The protection of concrete structures against corrosion in marine environments has always been a challenge due to the presence of a saline solution-A natural corrosive agent to the concrete paste and steel reinforcements. The concentration of salt is a key parameter influencing the rate of corrosion. In this paper, we propose an optical fiber-based salinity sensor based on bundled multimode plastic optical fiber (POF) as a sensor probe and a concave mirror as a reflector in conjunction with an intensity modulation technique. A refractive index (RI) sensing approach is analytically investigated and the findings are in agreement with the experimental results. A maximum sensitivity of 14,847.486/RIU can be achieved at RI = 1.3525. The proposed technique is suitable for in situ measurement and monitoring of salinity in liquid.
Polybutylene succinate (PBS) has become a potential candidate, similar to polypropylene (PP) and acrylonitrile butadiene styrene (ABS), for use as an organic plastic material due to its outstanding mechanical properties as well as high thermal deformation characteristics. A new composition of silica aerogel nanoparticles extracted from rice waste with PBS is proposed for use as a dielectric (εr = 4.5) substrate for microwave applications. A microstrip patch antenna was fabricated on the proposed dielectric substrate for multi-resonant ultra-wideband (UWB) applications. The performance characteristics of the proposed biomaterial-based antenna were investigated in a far-field measurement environment. The results indicate that the proposed biocompatible material-based antenna covered a bandwidth of 9.4 (2.3-11.7) GHz with stop bands from 5.5 GHz to 5.8 GHz and 7.0 GHz to 8.3 GHz. Peak gains of 9.82 dBi, 7.59 dBi, 8.0 dBi and 7.68 dBi were measured at resonant frequencies of 2.7 GHz, 4.6 GHz, 6.3 GHz and 9.5 GHz, respectively.
This study investigates the capacity of the nano-indentation method in the mechanical characterization of a heterogeneous dental restorative nanocomposite using experimental and computational approaches. In this respect, Filtek Z350 XT was selected as a nano-particle reinforced polymer nanocomposite with a specific range of the particle size (50 nm to 4 µm), within the range of indenter contact area of the nano-indentation experiment. A Sufficient number of nano-indentation tests were performed in various locations of the nanocomposite to extract the hardness and elastic modulus properties. A hybrid computational-experimental approach was developed to examine the extracted properties by linking the internal behaviour and the global response of the nanocomposite. In the computational part, several representative models of the nanocomposite were created in a finite element environment to simulate the mechanism of elastic-plastic deformation of the nanocomposite under Berkovich indenter. Dispersed values of hardness and elastic modulus were obtained through the experiment with 26.8 and 48.5 percent average errors, respectively, in comparison to the nanocomposite properties, respectively. A disordered shape was predicted for plastic deformation of the equilateral indentation mark, representing the interaction of the particles and matrix, which caused the experiment results reflect the local behaviour of the nanocomposite instead of the real material properties.
The main goal of the present work was to develop a value-added product of biodegradable material for sustainable packaging. The use of agriculture waste-derived carboxymethyl cellulose (CMC) mainly is to reduce the cost involved in the development of the film, at present commercially available CMS is costly. The main focus of the research is to translate the agricultural waste-derived CMC to useful biodegradable polymer suitable for packaging material. During this process CMC was extracted from the agricultural waste mainly sugar cane bagasse and the blends were prepared using CMC (waste derived), gelatin, agar and varied concentrations of glycerol; 1.5% (sample A), 2% (sample B), and 2.5% (sample C) was added. Thus, the film derived from the sample C (gelatin + CMC + agar) with 2.0% glycerol as a plasticizer exhibited excellent properties than other samples A and B. The physiochemical properties of each developed biodegradable plastics (sample A, B, C) were characterized using Fourier Transform Infra-Red (FTIR) spectroscopy and Differential Scanning Calorimetry (DSC), Thermogravimetric analysis (TGA). The swelling test, solubility in different solvents, oil permeability coefficient, water permeability (WP), mechanical strength of the produced material was claimed to be a good material for packaging and meanwhile its biodegradability (soil burial method) indicated their environmental compatibility nature and commercial properties. The reflected work is a novel approach, and which is vital in the conversion of organic waste to value-added product development. There is also another way to utilize commercial CMC in preparation of polymeric blends for the packaging material, which can save considerable time involved in the recovery of CMC from sugarcane bagasse.
The occurrence of microplastics (MPs) in saltwater bodies is relatively well studied, but nothing is known about their presence in most of the commercial salts that are widely consumed by humans across the globe. Here, we extracted MP-like particles larger than 149 μm from 17 salt brands originating from 8 different countries followed by the identification of their polymer composition using micro-Raman spectroscopy. Microplastics were absent in one brand while others contained between 1 to 10 MPs/Kg of salt. Out of the 72 extracted particles, 41.6% were plastic polymers, 23.6% were pigments, 5.50% were amorphous carbon, and 29.1% remained unidentified. The particle size (mean ± SD) was 515 ± 171 μm. The most common plastic polymers were polypropylene (40.0%) and polyethylene (33.3%). Fragments were the primary form of MPs (63.8%) followed by filaments (25.6%) and films (10.6%). According to our results, the low level of anthropogenic particles intake from the salts (maximum 37 particles per individual per annum) warrants negligible health impacts. However, to better understand the health risks associated with salt consumption, further development in extraction protocols are needed to isolate anthropogenic particles smaller than 149 μm.
Polyhydroxyalkanoate (PHA) is a promising candidate for use as an alternative bioplastic to replace petroleum-based plastics. Our understanding of PHA synthase PhaC is poor due to the paucity of available three-dimensional structural information. Here we present a high-resolution crystal structure of the catalytic domain of PhaC from Chromobacterium sp. USM2, PhaC Cs -CAT. The structure shows that PhaC Cs -CAT forms an α/β hydrolase fold comprising α/β core and CAP subdomains. The active site containing Cys291, Asp447 and His477 is located at the bottom of the cavity, which is filled with water molecules and is covered by the partly disordered CAP subdomain. We designated our structure as the closed form, which is distinct from the recently reported catalytic domain from Cupriavidus necator (PhaC Cn -CAT). Structural comparison showed PhaC Cn -CAT adopting a partially open form maintaining a narrow substrate access channel to the active site, but no product egress. PhaC Cs -CAT forms a face-to-face dimer mediated by the CAP subdomains. This arrangement of the dimer is also distinct from that of the PhaC Cn -CAT dimer. These findings suggest that the CAP subdomain should undergo a conformational change during catalytic activity that involves rearrangement of the dimer to facilitate substrate entry and product formation and egress from the active site.
There is a paucity of information about the occurrence of microplastics (MPs) in edible fish tissues. Here, we investigated the potential presence of MPs in the excised organs (viscera and gills) and eviscerated flesh (whole fish excluding the viscera and gills) of four commonly consumed dried fish species (n = 30 per species). The MP chemical composition was then determined using micro-Raman spectroscopy and elemental analysis with energy-dispersive X-ray spectroscopy (EDX). Out of 61 isolated particles, 59.0% were plastic polymers, 21.3% were pigment particles, 6.55% were non-plastic items (i.e. cellulose or actinolite), while 13.1% remained unidentified. The level of heavy metals on MPs or pigment particles were below the detection limit. Surprisingly, in two species, the eviscerated flesh contained higher MP loads than the excised organs, which highlights that evisceration does not necessarily eliminate the risk of MP intake by consumers. Future studies are encouraged to quantify anthropogenic particle loads in edible fish tissues.
Strict environmental concerns, depleting natural recourses, and rising demand for building construction materials have promoted scientific research toward alternative building materials. This research supports the idea of sustainability and a circular economy via the utilization of waste to produce value-added products. The research explored the potential of waste plastics and silica sand for developing thermoplastic composite as floor tiles. The samples were characterized by water absorption, compressive strength, flexural strength, and sliding wear. The morphological analysis of the sand-plastic interfaces was covered under the umbrella of this study. The maximum compressive and flexural strength were found to be 46.20 N/mm2 and 6.24 N/mm2, respectively, with the minimum water absorption and sliding wear rate of 0.039% and 0.143 × 10-8 kg/m, respectively. The study suggests the workability of the developed floor tiles in non-traffic areas of public places. Thus, the study provides a green building material through recycling waste plastics for sustainable development.
Plastic sand paver blocks provide a sustainable alternative by using plastic waste and reducing the need for cement. This innovative approach leads to a more sustainable construction sector by promoting environmental preservation. No model or Equation has been devised that can predict the compressive strength of these blocks. This study utilized gene expression programming (GEP) and multi-expression programming (MEP) to develop empirical models to forecast the compressive strength of plastic sand paver blocks (PSPB) comprised of plastic, sand, and fibre in an effort to advance the field. The database contains 135 results for compressive strength with seven input parameters. The R2 values of 0.87 for GEP and 0.91 for MEP for compressive strength reveal a relatively significant relationship between predicted and actual values. MEP outperformed GEP by displaying a higher R2 and lower values for statistical evaluations. In addition, a sensitivity analysis was conducted, which revealed that the sand grain size and percentage of fibres play an essential part in compressive strength. It was estimated that they contributed almost 50% of the total. The outcomes of this research have the potential to promote the reuse of PSPB in the building of green environments, hence boosting environmental protection and economic advantage.
In this study, the rice husk flour-plastic waste composites (RPC) was produced from polypropylene (PP) and high density polyethylene (HDPE) wastes with 30 and 50% rice husk flour (RHF) contents. RPC was made by melt compounding and compression moulding processes. The electrical resistivity, thermal stability and tensile strength of RPC were determined. The RPC was tested in electrical resistivity and tensile strength according to the ASTM D-257 and ASTM D-638 respectively, while thermal stability was tested using thermogravimetric analysis (TGA) method. From the results, high content of RHF reduces all properties, except for tensile modulus of elasticity (TMOE) in tensile strength test. The ability of moisture absorption and the presence of hemicelluloses, cellulose and silica in RHF reduce the electrical resistivity and thermal stability behaviour of RPC from 50% RHF. The good binding elements and filler agglomeration in RPC from 50% RHF improve only TMOE. Insufficient stress transfer and rigid interphase occurred between RHF and plastics during tensile maximum load and elongation at break (Eb) in tensile strength test. In general, RPC from HDPE indicates better thermal stability, tensile modulus of rupture and Eb (in tensile strength test) compared to PP, based on the good behaviour of thermal conductivity, low water absorption, high molecular weight and good elongation properties of HDPE. However, RPC from PP shows good electrical resistance due to the low thermal expansion coefficient of PP.
Poly(lactic acid) (PLA)-based nanocomposites filled with graphene nanoplatelets (xGnP) that contains epoxidized palm oil (EPO) as plasticizer were prepared by melt blending method. PLA was first plasticized by EPO to improve its flexibility and thereby overcome its problem of brittleness. Then, xGnP was incoporated into plasticized PLA to enhance its mechanical properties. Plasticized and nanofilled PLA nanocomposites (PLA/EPO/xGnP) showed improvement in the elongation at break by 3322% and 61% compared to pristine PLA and PLA/EPO, respectively. The use of EPO and xGnP increases the mobility of the polymeric chains, thereby improving the flexibility and plastic deformation of PLA. The nanocomposites also resulted in an increase of up to 26.5% in the tensile strength compared with PLA/EPO blend. XRD pattern showed the presence of peak around 26.5° in PLA/EPO/xGnP nanocomposites which corresponds to characteristic peak of graphene nanoplatelets. Plasticized PLA reinforced with xGnP showed that increasing the xGnP content triggers a substantial increase in thermal stability. Crystallinity of the nanocomposites as well as cold crystallization and melting temperature did not show any significant changes upon addition of xGnP. However, there was a significant decrease of glass transition temperature up to 0.3wt% of xGnP incorporation. The TEM micrograph of PLA/EPO/xGnP shows that the xGnP was uniformly dispersed in the PLA matrix and no obvious aggregation was observed.
The electrical resistivity and flexural strength of plastic composites reinforced with pineapple leaf particles (PCPLP) is presented. PCPLP were produced using different plastic materials; Polyethylene (PE) and Polypropylene (PP), and different plastic pineapple leaf particle ratios; 50:50 and 70:30. The PCPLP were tested and evaluated with respect to electrical resistivity and flexural strength according to ASTM D257 and D790, respectively. The results indicate that PCPLP made from PP exhibits better electrical resistance than PE, which may be attributed to the better frequency insulation behaviour ofPP. PCPLP using the higher ratio of 70:30 also exhibited better electrical resistance than the lower 50:50 ratio. Cellulose materials inherently influence the electrical resistance of plastic composites, due to their natural propensity to absorb moisture. The PCPLP produced using a ratio of 50:50 for both PP and PE composites exhibited better MOE results than the 70:30 composites, however the converse is true with respect to the MOR. MOE of PCPLP was increased with increasing pineapple leaf particles content due to the greater matrix stiffness of this natural particle with respect to plastic matrix. However, high percentage offiller particles in the matrix (70:30 ratio) has reduced the toughness in the composite structure due to the lost ofphysical contact between high accumulated particles.
With the world facing depletion of its oil reserves, attention is being focused on how the plastics industry will address shortages and price increases in its crucial raw materials. One renewable resource is that of vegetable oils and fats and about a dozen crop plants make up the main vegetable oil-seed market. The main constituents of these oils are saturated and unsaturated fatty acids that are unique to the plant in which they have been developed. Moreover, technological processes can produce more well-defined and pure oils, and the fatty acid contents in the vegetable oils can be altered with modern crop development techniques. This article describes recent advances in utilising such vegetable oils in sourcing new polymeric materials. It also gives the context for the development of polymers based on renewable materials in general.
Mango as a climacteric fruit is known to have increased auxins with concomitant increased ethylene and carbon dioxide production during ripening. Such hormonal properties alongside many other nutritional benefits prepared in the form of compost extract were tested for enhancing production of medicinal bitter gourd of Momordica charantia. This cucurbit was planted on field beds at 0.8 x 0.5 m followed by application of compost extract prepared with anaerobic decomposition of rotting mango fruits, fish wastes of gills and internal organs and brown sugar at different ratios in plastic containers. The results obtained showed that mango:fish wastes:sugar compost extract of 2:1:1 applied to soil around the root collar at 10 ml at fortnight intervals allowed the plants to gain the highest mean number of fruits per plant of 18.3, mean individual fruit weight of 25.95 g or mean yield of 11.80 tonnes per hectare. Mango compost extract is, hence, beneficial in organic production of this medicinal bitter gourd.
A novel powdering material that utilizes acid-modified Imperata cylindrica (IC) powder for the development of fingermarks was studied. Experiments were carried out to determine the suitability, adherence quality and sensitivity of the acid-modified IC powder. Fingermarks of different constituents (eccrine, sebaceous and natural fingermarks) on different types of surfaces were used. Acid-modified IC powder was also used to develop fingermarks of different ages as well as aged fingermarks recovered from the water. From the visual inspection, acid-modified IC powder was able to interact with different fingermark constituents and produced distinct ridge details on the examined surfaces. It was also able to develop aged fingermarks and fingermarks that were submerged in water. A statistical comparison was made against the Sirchie® Hi-Fi black powder in terms of the powders' sensitivity and quality of the developed natural fingermarks. The image quality was analyzed using MITRE's Image Quality of Fingerprint (IQF) software. From the experiments, acid-modified IC powder has the potential as a fingermark development powder, although natural fingermarks developed by Sirchie® black powder showed better quality and sensitivity based on the results of the statistical comparison.
Various production methods have been developed for graphene production, but each of them falls short in either the economic or quality aspect. In this paper, we present the flame deposition method, a modified chemical vapor deposition (CVD) that uses an open-flame. In this method, resulting carbon deposits were found to be graphitic in nature, thereby suggesting multilayer graphene growth in a very short reaction time of 5 min. Furthermore, the deposits were transferred onto a cyanoacrylate plastic substrate and its sheet resistance was measured to be 81 ohm/square. The results showed that open-flame deposition exhibits high potential for low-cost, low-energy and high-quality production of graphene.
Composite materials have increasingly become crucial in manufacturing engineering products and producing commodity
materials in the major industries including; automotive, aerospace, marine, construction, agriculture and health science.
However, several improvements regarding the strength, dimensional stability and the cost of production are required.
In this study, composite of Kenaf, multi-wall carbon nanotube (MWCNT) and polypropylene (PP) with maleic anhydridegrafted
polypropylene (MAPP) are examined. The results highlight that increasing MAPP loading, in turn, increases the
value of the mechanical properties. The composites are produced by blending kenaf/MWCNT/PP using a Sigma blade
mixer and injection moulding. Injection moulding is a significant operation used to produce plastic products. In the
study, Kenaf core fibre was mixed with MWCNT and polypropylene, in addition to MAPP. The MAPP is added by applying
different percentage (1, 2, 3 and 4 wt. %) during the blending process. The main objective of the study was to analyse the
effects of MAPP concentrations on the mechanical properties of the Kenaf/MWCNT/PP composite. The results of the study
established that MAPP 3 wt. % concentration with MWCNT 3 wt. % loading and Kenaf 30 wt. % filler provide optimum
results for the composites. There was approximately, a 21% enhance in tensile strength of Kenaf 30 wt. %/MWCNT, 3 wt.
%/MAPP, 3 wt. %/PP observed compared to the (without) MAPP composite. The composites with coupling agent stimulate
better filler dispersion between Kenaf, MWCNT and PP observed using a scanning electron microscope (SEM) and fieldemission
scanning electron microscope (FESEM).
The problem of stagnation point flow over a stretching/shrinking sheet immersed in a micropolar fluid is analyzed
numerically. The governing partial differential equations are transformed into a system of ordinary (similarity) differential
equation and are then solved numerically using the boundary value problem solver (bvp4c) in Matlab software. The
effects of various parameters on the velocity and the angular velocity as well as the skin friction coefficient and the couple
stress are shown in tables and graphs. The noticeable results are found that the micropolar and the slip parameters
decrease the skin friction coefficient and the couple stress in the existence of magnetic field. Dual solutions appear for
certain range of the shrinking strength. A stability analysis is performed to determine which one of the solutions is stable.
Practical applications include polymer extrusion, where one deals with stretching of plastic sheets and in metallurgy
that involves the cooling of continuous strips.
The increase use of synthetic packaging films in food products has led to serious environmental problems due to their total non-biodegradability property. Nutrient composition and sensory acceptability of chicken patties formulated with various levels of Pleurotus sajor-caju popularly known as grey oyster mushroom (oM) and wrapped with degradable plastic were studied. The chicken patties were formulated with either 0, 25 or 50% of fresh oM. The results showed that chicken patty formulated with 25% PSC has protein content of 17.46% lower than the control patty which had 18.13% but it was not significant (p>0.05). After storage, cooked chicken patty formulated with 25% oM had protein content of 21.53% lower than the control patty (23 .90%) but it was not significant (p>0 .05). However, incorporation of oM in chicken patties resulted in decreasing of fat content significantly (p0 .05) from 15.58 (control) to 13.33% after storage. On the other nutrient, the concentration of f3-glucan were detected at values ranged between 0.70 and 0.76 (g1100 g) after 6 month. Other results showed that patty formulated with 25% oM received the highest scores for all attributes except for aroma. Meanwhile, patty prepared with 50% oM received the highest score of aroma attribute after 6 month of storage. However, the score values for all attributes of all oM-based patties were not statistically different with control patty (p> 0.05). In conclusion, the addition of oM at 25% can be recommended for the purpose of lowering fat content while keeping protein and f3-glucan unchanged without jeopardizing sensorial properties. This investigation therefore, suggested that biodegradable plastic can be used in packing any type of processed meat-based products.
As of today, ultra-high molecular weight polyethylene (UHMWPE) is a thermoplastic material normally used as bearing
components for human joint replacements. However, formation of wear debris from UHMWPE after certain service
periods may cause adverse effects which remain as unresolved issues. In this study, mechanical and dry sliding wear
properties of UHMWPE reinforced with different loading of talc particles were investigated. The wear test was carried
out using Ducom TR-20 pin-on-disc tester at different pressure velocity (pv) factors under dry sliding conditions. The
worn surfaces and transfer films of pure UHMWPE and talc/UHMWPE composites were observed under scanning electron
microscope (SEM). The experimental results showed that the microhardness increased with the increase of talc loadings
in UHMWPE. The 20 wt. % talc/UHMWPE composites showed a 17% increment in microhardness as compared with pure
UHMWPE. The dry sliding wear behaviour of UHMWPE was also improved upon the reinforcement of talc. The wear rate
of UHMWPE decreased after incorporation of talc particles. The coefficient of friction (COF) increased slightly under low
pv conditions. At high pv conditions, the COF decreased in values with increasing talc loadings. The improvement in
wear behaviour may be attributed to the increase in load-carrying capacity and surface hardness of the talc/UHMWPE
composites. SEM micrographs on worn surfaces showed that plastic deformation and grooving wear were dominant for
UHMWPE. The plastic deformation and grooving wear were reduced upon the reinforcement of talc particles. The talc/
UHMWPE composites produced smoother and uniform transfer films as compared to pure UHMWPE.