MyMedR

Displaying publications 101 - 120 of 139 in total

Abstract:

Sort:

Fulltext Industry and cosmetic uses of talc with their implication on health

Sinniah, Davendralingam

International e-Journal of Science, Medicine & Education, 2011;5(1):10-16.
MyJurnal

Talc’s softness, whiteness, lamellarity, inertness and affinity for organic chemicals make it valuable for industrial and domestic applications. The largest consumers are the paper and ceramic industry; only 5% is used as cosmetics. It is also used for preserving animal feed, and a carrier for drugs, insecticides, pesticides and chemicals. Talc was introduced as baby powder in 1894 and advertised aggressively worldwide. Widespread and indiscriminate use soon raised concerns about its implications for health. The IARC found that talc containing asbestiform fibres is carcinogenic to humans, but inadequate evidence to implicate talc not-containing asbestiform fibres. Pulmonary manifestations of talc inhalation include talcosis, talcosilicosis, and talcoasbestosis. Drug-users administering talc-adulterated oral medications intravenously develop pulmonary granulomas, fibrosis and irreversible pulmonary hypertension. Worldwide reports reveal talc inhalation is fatal to infants; it coats and dries mucus membranes, causes hemorrhage, edema, desquamation of bronchial epithelium, and clogs and compromises mucociliary clearance; larger quantities completely obstruct airways. Progressive diffuse pulmonary fibrosis is a recognized sequel to massive aspiration of baby powder. IARC has classified perineal use of talcum powder as a possible ovarian carcinogen, while a recent study has found that perineal talcum powder increases the risk of endometrial cancer among postmenopausal women. There is a need to raise public awareness of the serious risks associated with the use of talcum powder and for legislation to protect the health of the uninformed who represent the poorer segment of the community, and infants and young children. The dangers associated with cosmetic use of talc outweigh any possible benefits.

Matched MeSH terms: Ceramics
Effect of BaAl2O4 addition on power consumption and oxygen sensing response of Er123 ceramic rods utilizing hot-spot phenomenon

Hassan M, Yahya A, Okamoto T

Sains Malaysiana, 2011;40.

In this paper, we report the effect of BaAl2O4 addition (0-30 wt. %) on power consumption and oxygen sensing response of hot-spots developed on short Er123 ceramic rods of around 12 mm length synthesized using standard solid-state reaction. All the sensor rods showed increase in output current with increasing voltage followed by sudden reduction in output current and appearance of hot spot. After appearance of hot spot, for each rod, output current was observed to decrease gradually with increasing voltage with the slope of the I-V curve gradually approaching zero. Output current after the hot spot formation showed sensitivity to oxygen partial pressure, pO2 between 1 to 100 kPa. Addition of 30 wt. % BaAl2O4 reduced the fluctuation of current and increased the sensitivity for pO2 below 10 kPa. In addition, overshoot current was also reduced and resulted in improvement of response time from around 10 s to 5 s. Our result also showed that minimum power consumption was significantly reduced in the Er123 rods with 30 wt. % BaAl2O4.

Matched MeSH terms: Ceramics
An in vitro study to evaluate the genotoxicity of value added hydroxyapatite as a bone replacement material

Akram Hassan, Swaminathan D

Sains Malaysiana, 2011;40.

Hydroxyapatite (HA) used for bone replacement is one of the most active areas of ceramic biomaterials research currently. It has been used clinically for the last 20 years due to its excellent biocompatibility, osseoconduction and osseointegration. Many modifications have been done to develop a stronger, tougher and biocompatible ceramic biomaterial because pure HA is brittle. Researchers in Universiti Sains Malaysia had developed this value added HA that is stronger and less brittle compared to pure HA. The objective of this in vitro study was to evaluate the genotoxic characteristic of the value added HA based material by using Bacterial Reverse Mutation Assay (Ames test). The Bacterial Reverse Mutation Assay of HA was performed on Salmonella typhimurium strains TA98, TA100, TA1535, TA1537 and Escherichia coli strain WP2 uvrA using the preincubation method in the presence and absence of an exogenous metabolic activation system. All the bacterial tester strains treated with and without S9 Mix showed no increase of revertant colonies with increase in concentration of test substance for both the dose finding test and the main test. The number of revertant colonies was less than twice that of the solvent control for all the five bacterial strains and this was reproducible for both the dose finding test and the main test. The numbers of revertant colonies in the negative and positive controls were within the background data of our laboratory. In conclusion the results of the tests showed that the value added HA was considered to have no reverse mutagenic potential under the present test conditions.

Matched MeSH terms: Ceramics
Biaxial flexural strength of Turkom-Cera core compared to two other all-ceramic systems

Al-Makramani BM, Razak AA, Abu-Hassan MI

J Appl Oral Sci, 2010 Dec;18(6):607-12.
PMID: 21308292

Advances in all-ceramic systems have established predictable means of providing metal-free aesthetic and biocompatible materials. These materials must have sufficient strength to be a practical treatment alternative for the fabrication of crowns and fixed partial dentures.
OBJECTIVES: The aim of this study was to compare the biaxial flexural strength of three core ceramic materials.
MATERIAL AND METHODS: Three groups of 10 disc-shaped specimens (16 mm diameter x 1.2 mm thickness - in accordance with ISO-6872, 1995) were made from the following ceramic materials: Turkom-Cera Fused Alumina [(Turkom-Ceramic (M) Sdn Bhd, Puchong, Selangor, Malaysia)], In-Ceram (Vita Zahnfabrik, Bad Säckingen, Baden-Württemberg, Germany) and Vitadur-N (Vita Zahnfabrik, Bad Säckingen, Baden-Württemberg, Germany), which were sintered according to the manufacturer's recommendations. The specimens were subjected to biaxial flexural strength test in an universal testing machine at a crosshead speed of 0.5 mm/min. The definitive fracture load was recorded for each specimen and the biaxial flexural strength was calculated from an equation in accordance with ISO-6872.
RESULTS: The mean biaxial flexural strength values were: Turkom-Cera: 506.8 ± 87.01 MPa, In-Ceram: 347.4 ± 28.83 MPa and Vitadur-N: 128.7 ± 12.72 MPa. The results were analyzed by the Levene's test and Dunnett's T3 post-hoc test (SPSS software V11.5.0 for Windows, SPSS, Chicago, IL, USA ) at a preset significance level of 5% because of unequal group variances (P<0.001). There was statistically significant difference between the three core ceramics (P<0.05). Turkom-Cera showed the highest biaxial flexural strength, followed by In-Ceram and Vitadur-N.
CONCLUSIONS: Turkom-Cera core had significantly higher flexural strength than In-Ceram and Vitadur-N ceramic core materials.

Matched MeSH terms: Ceramics/chemistry*
Current status of ceramic-based membranes for oxygen separation from air

Hashim SM, Mohamed AR, Bhatia S

Adv Colloid Interface Sci, 2010 Oct 15;160(1-2):88-100.
PMID: 20813344 DOI: 10.1016/j.cis.2010.07.007

There has been tremendous progress in membrane technology for gas separation, in particular oxygen separation from air in the last 20 years. It provides an alternative route to the existing conventional separation processes such as cryogenic distillation and pressure swing adsorption as well as cheaper production of oxygen with high purity. This review presents the recent advances of ceramic membranes for the separation of oxygen from air at high temperature. It covers the issues and problems with respect to the selectivity and separation performance. The paper also presents different approaches applied to overcome these challenges. The future directions of ceramic-based membranes for oxygen separation from air are also presented.

Matched MeSH terms: Ceramics/chemistry*
Fulltext Preparation and characterization of glass-ceramic synthesized from soda lime glass and wastewater sludge

Zaidan Abdul Wahab, Syaharudin Zaibon, Khamirul Amin Matori, Norfarezah Hanim Edros, Thai, Ming Yeow, Mohd Zul Hilmi Mayzan, et al.

Pertanika Journal of Science & Technology, 2010;18(2):-.
MyJurnal

This paper reports an alternative method for making glass-ceramic from disposal waste water
sludge and soda lime silica (SLS) glass. The glass ceramic samples were prepared from a mixture
of wastewater sludge and SLS glasses, melted at 1375°C for 3 hours and quenched by pouring into
water to obtain a coarse frit. The frit glass was then crushed and sieved to 106μm before it was
pressed to a pellet. The sintering process was performed at various temperatures between 700-
1000°C for 2 hours and morphologically characterized with XRD, SEM, and EDX. Overall results
showed the crystalline phase of diopside sodian-critobalite glass-ceramic is depending on thermal
treatment process and making them attractive to industrial uses such as in construction, tiling, and
glass-ceramic applications.

Matched MeSH terms: Ceramics
Fulltext Recovery of uranium from Malaysian non-conventional sources

Meor Yusoff, M.S.

Journal of Nuclear and Related Technologies, 2010;2010(2):55-65.
MyJurnal

The recovery of uranium from non-conventional sources has its importance in the security of nuclear fuel supply as well as producing a more value-added product to the contaminated source. In this paper, uranium is recovered both by developing a hydrothermal process as well as using the removal method. Developing hydrothermal process involves using high uranium concentrated starting material such as xenotime and thorium hydroxide waste produced from the monazite cracking process. Oxalate separation enable to produce a better uranium and thorium separation from the yttrium in xenotime as compared to the hydroxide precipitation. Also, a solvent extraction stage was included to separate the uranium from the thorium in the process using thorium hydroxide waste. The removal method involves using selective leaching for minerals with lower uranium content such as zircon. A better removal for uranium and thorium in zircon is achieved when a heat treatment process was done prior to the leaching stage. White zircon mineral was produced after this treatment and its quality meets the requirement for white ceramic opacifier and glaze.

Matched MeSH terms: Ceramics
Fulltext Study on radon emanation from selected building materials in Malaysia

Ahmed, Al-Halemi, Jaafar, M.S.

Journal of Nuclear and Related Technologies, 2010;2010(1):14-20.
MyJurnal

Radon-222 emanation from selected locally produced samples of building materials, used in Malaysia were measured using the Professional Continuous Radon Monitor Model 1027, which is a patented electronic detecting-junction photodiode sensor to measure the concentration of radon gas. Each sample was placed for 72 hours inside a 3.11 x 10 -2 m 3 sealed container. It was found that the average radon concentration Bqm -3 of air for concrete bricks, concrete brick with cemented coatings, concrete brick with cemented coatings and paint samples were, 303.7 Bq/m 3, 436.6 Bqm -3, and 410.7 Bqm -3, respectively. (Bqm -3 ) for brown clay brick, brown clay brick with cemented coatings, brown clay brick with cemented coatings and paint were 166.5 Bqm -3, 166.5 Bqm -3, and 148 Bqm -3, respectively. (Bqm -3 ) for sample of compact ceramic tile was 0 Bqm -3. The findings show that concrete brick samples are important source of radon emanation, while brown clay brick have been accepted as the recommendation of the U.S. Environmental Protection Agency (EPA), and ceramic tiles had no emanation of radon gas due to their compact surface, or the glazed layer created on the tile surface during the manufacturing process, which blocks radon emanation. A positive correlation between radon emanation and radium content has been observed for both brown clay brick and concrete brick samples whereas a negative correlation for ceramic tile has been observed. Consequently from the findings, in order to reduce radon emanation and radon exposure in house dwellings and in addition to EPA recommendation of sealed cracks and established good ventilation, we recommend concrete walls to be painted and concrete floors to be paved with ceramic tiles.

Matched MeSH terms: Ceramics
Fulltext Cement-boron carbide concrete as radiation shielding material

Yusof Abdullah, Mohd Reusmaazran Yusof, Azali Muhamad, Zaifol Samsu, Nurhaslinda Ee Abdullah

Journal of Nuclear and Related Technologies, 2010;2010(2):74-79.
MyJurnal

Boron carbide (B4C) is a ceramic material which is effective to absorb thermal neutron due to wide neutron absorption cross section. In this work, B4C is added into concrete as fine aggregates to test the attenuation properties by getting the attenuation coefficient of the concrete/B4C. The samples of concrete/B4C were exposing to the thermal neutron radiation source (241-Americium-Berylium) at the dos rate of 29.08 mR/h. The result show that the attenuation coefficient of the sample with 20wt% B4C is 0.299cm -1 and the sample without B4C is 0.238cm -1 and hence, concrete/B4C is suitable as a shield for thermal neutron radiation.

Matched MeSH terms: Ceramics
Removal of boron from ceramic industry wastewater by adsorption-flocculation mechanism using palm oil mill boiler (POMB) bottom ash and polymer

Chong MF, Lee KP, Chieng HJ, Syazwani Binti Ramli II

Water Res, 2009 Jul;43(13):3326-34.
PMID: 19487007 DOI: 10.1016/j.watres.2009.04.044

Boron is extensively used in the ceramic industry for enhancing mechanical strength of the tiles. The discharge of boron containing wastewater to the environment causes severe pollution problems. Boron is also dangerous for human consumption and causes organisms' reproductive impediments if the safe intake level is exceeded. Current methods to remove boron include ion-exchange, membrane filtration, precipitation-coagulation, biological and chemical treatment. These methods are costly to remove boron from the wastewater and hence infeasible for industrial wastewater treatment. In the present research, adsorption-flocculation mechanism is proposed for boron removal from ceramic wastewater by using Palm Oil Mill Boiler (POMB) bottom ash and long chain polymer or flocculant. Ceramic wastewater is turbid and milky in color which contains 15 mg/L of boron and 2000 mg/L of suspended solids. The optimum operating conditions for boron adsorption on POMB bottom ash and flocculation using polymer were investigated in the present research. Adsorption isotherm of boron on bottom ash was also investigated to evaluate the adsorption capacity. Adsorption isotherm modeling was conducted based on Langmuir and Freundlich isotherms. The results show that coarse POMB bottom ash with particle size larger than 2 mm is a suitable adsorbent where boron is removed up to 80% under the optimum conditions (pH=8.0, dosage=40 g bottom ash/300 ml wastewater, residence time=1h). The results also show that KP 1200 B cationic polymer is effective in flocculating the suspended solids while AP 120 C anionic polymer is effective in flocculating the bottom ash. The combined cationic and anionic polymers are able to clarify the ceramic wastewater under the optimum conditions (dosage of KP 1200 B cationic polymer=100 mg/L, dosage of AP 120 C anionic polymer=50 mg/L, mixing speed=200 rpm). Under the optimum operating conditions, the boron and suspended solids concentration of the treated wastewater were reduced to 3 mg/L and 5 mg/L respectively, satisfying the discharge requirement by Malaysia Department of Environment (DOE). The modeling study shows that the adsorption isotherm of boron onto POMB bottom ash conformed to the Freundlich Isotherm. The proposed method is suitable for boron removal in ceramic wastewater especially in regions where POMB bottom ash is abundant.

Matched MeSH terms: Ceramics*
Fulltext Characterization and phase evolution of cordierite based glass synthesis from pure oxide and minerals

Banjuraizah Johar, Hasmaliza Mohamad, Zainal Arifin Ahmad

Journal of Nuclear and Related Technologies, 2009;2009(1):237-246.
MyJurnal

α Cordierite is very important phase in MgO-Al2O3-SiO2 system because of their very outstanding thermal, chemical and electrical properties. In this presents study nonstoichiometry cordierite (MgO:Al2O3:SiO2 = 3:1.5:5) using 2 different initial raw materials ( (i)mixture of pure oxide, and ii) mainly mixture of minerals) were fabricated and compared in terms of phase transformation and physical properties. Cordierite was prepared by glass method at low melting temperature (1350°C). Low melting temperature has resulted in partly crystalline glass which has possesses higher hardness, required longer milling time and result in contamination from grinding media. However, α-cordierite has successfully crystallized and fully densified at 850°C/2h. Activation energy for densification was investigated from thermal expansion coefficient (TCE) results. Other properties that were discussed included thermal properties using DTA/TGA.

Matched MeSH terms: Ceramics
Fulltext Synthesis and characterization of β-tricalcium phosphate ceramic via sol-gel method

Mohd Al Amin Muhamad Nor, Maryam Mohd Ridzuan, Zainal Arifin Ahmad

Journal of Nuclear and Related Technologies, 2009;2009(1):199-205.
MyJurnal

Ceramic materials play key role in several biomedical applications. One of them is bone graft which is use in treating bone defect which caused by injury or osteoporosis. Calcium phosphates based ceramic are preferred as bone grafts in hard tissue engineering because of their chemical compositions are similar to the composition of human bone, superior bioresorbable and bioactivity. In this study, β-tricalcium phosphate (β-TCP) ceramic was synthesized by using sol-gel method. Phosphorous pentoxide (P2O5) and calcium nitrate tetrahydrate (Ca(NO3)2.4H2O) were used as calcium and phosphate precursors. The effects of calcination temperature on the synthesis powder were studied using the XRD, SEM-EDS and FTIR techniques. It was found that calcination temperature greatly influence the purity of the synthesized powders. The β-TCP was the dominant phase with the formation of α-TCP at calcination temperature from 600 to 800°C. Pure β-TCP was obtained at calcination of 900°C. As the temperature increased to 1000°C, the β-TCP was decomposed to for calcium phosphate oxide (CPO). The sol-gel method has some advantages over other methods, mainly its simplicity and ability to produce pure β-TCP at lower calcination temperature.

Matched MeSH terms: Ceramics
Fulltext Effects of sintering time on the physical and compositional properties of porous biphasic calcium phosphate foam

Cik Rohaida, C.H., Idris, B., Rusnah, M., Mohd Reusmaazran, Y., Narimah, A.B.

Journal of Nuclear and Related Technologies, 2009;2009(1):206-216.
MyJurnal

Phase composition of calcium phosphate ceramic is a characteristic directly related to the biological response of implants due to the differences in mechanical and biochemical properties of these compounds. The biodegradation rate of biphasic calcium phosphate (BCP) can be controlled by altering the HA to β-TCP ratios. In this study the crystalline phase evolution of BCP synthesized via precipitation from aqueous solution of (NH4)2PO4 titrated into heated solution of Ca (NO3)2 was evaluated. The resulting powder was fabricated into porous scaffold using polyurethane foam method. Bulk powders were sintered from 700 - 1400°C to determine the most significant sintering temperature to obtain a stable and well crystallize BCP phases. The porous scaffolds were then sintered at selected temperature and the effects of various sintering times from 5,7,9,11,13 and 15 h were investigated. Bulk powders were characterized by dilatometer, IR analysis and XRD and porous scaffolds were analyzed by XRD and SEMEdx. RIR method was performed to show that the HA to β-TCP ratios were increased with increasing of sintering time and reached the maximum HA value at 11h. It is found that, the possibilities to manipulate the HA to β-TCP ratios in BCP porous scaffold by just controlling the sintering time of the scaffold without controlling the starting powder characteristics.

Matched MeSH terms: Ceramics
Fulltext Mechanical activation of ultrafine cordierite: effect of grinding time

Affendi, A.F., Hasmaliza, M., Srimala, S.

Journal of Nuclear and Related Technologies, 2009;2009(1):247-254.
MyJurnal

In these studies, cordierite was mechanically synthesized after a sol-gel process. The effect of milling time of cordierite was investigated. Aluminium nitrate nonahydrate, magnesium nitrate hexahydrate and tetraethylorthosilicate (TEOS) were used as starting materials. Gels obtained were mechanically activated in planetary ball mill by at 300rpm grinding speed and grinding time (15min, 30min, 45min and 60min). Powders produced were characterized by X-Ray Diffraction (XRD) and Field Emission Scanning Electron Microscope (FESEM) and Energy Dispersive X-Ray (EDX). XRD analysis proved that α-cordierite was formed at lower temperature (1200°C) as compliment to without grinding, whereby it is formed at1300°C. FESEM analysis shows the size of the cordierite were in submicron scale. EDX analysis proved that magnesium, aluminium, silicon and oxygen are elements existed in cordierite.

Matched MeSH terms: Ceramics
Fulltext Impedance studies on ca0.5 sr0.5 cu3 ti4 O12 ceramic oxide

Mazni Mustafa, W. Mohamad Daud W. Yusoff, Zainal Abidin Talib, Abdul Halim Shaari, Primus, Walter Charles

Pertanika Journal of Science & Technology, 2009;17(1):-.
MyJurnal

Ca0.5Sr0.5Cu3Ti4O12 (CSCTO) ceramic oxide was prepared using solid state reaction technique. Impedance measurement was done using High Dielectric Resolution Analyzer (Novocontrol Novotherm) from 30 oC to 250 oC, in the frequency range of 10-2 to 106 Hz. X-ray diffraction pattern showed a single phase with a cubic structure. In the complex impedance plot, three semi-circles were observed; these represented the grain, grain boundary and electrode effect responses. The semi-circles were fitted using a series network of three parallel RC circuits. The resistance was found to increase with the decreasing temperature. The activation energies, Ea, obtained from the Arrhenius plots of CSCTO, were 0.31 eV and 0.73 eV for grain and grain boundary conductivity, respectively. The value of the grain energy was revealed as smaller than the grain boundary energy, due to the semi-conducting grain and the insulating grain boundary characteristic (Sinclair et al., 2002).

Matched MeSH terms: Ceramics
Fulltext Rietveld quantitative phase analysis of non-stoichiometric cordierite synthesised from mainly talc and kaolin: effect of sintering temperature

Banjuraizah Johar, Hasmaliza Mohamad, Zainal Arifin Ahmad

Journal of Nuclear and Related Technologies, 2009;2009(1):103-110.
MyJurnal

Indialite or α-cordierite was synthesized by glass crystallization method using mainly talc and kaolin and with small amount of MgO, Al2O3, SiO2 to compensate the chemical formulation of non-stoihiometric compositions of cordierite. (3MgO.1.5Al2O3.5SiO2). B2O3, P2O5 and CaO was also added to decrease the melting and sintering temperature of cordierite. The glasses were pelletized and sintered from 850 o C up to 1050 o C. Phase compositions of both heat treated glass was quantified by X-ray powder diffraction data by the Rietveld method using TOPAS Ver 3 software. Result shows that about 60wt% of α cordierite has successfully crystallized at 850 o C. Beside secondary phases (forsterite) which come from initial raw materials, phases from grinding media were also presents in the sample. The contamination was considered high since it has reacted with existence phases to form a new phase at higher temperature. Without any contamination from grinding it was expected to obtain more than 90wt% α cordierite using the same composition.

Matched MeSH terms: Ceramics
Fulltext Electrodeposition of nickel-phosphorus-alumina composite coatings

Nur Azam Badarulzaman, Ng, Jun Wei, Ahmad Azmin Mohamad, Purwadaria, Sunara, Zainal Arifin Ahmad

Journal of Nuclear and Related Technologies, 2009;2009(1):43-50.
MyJurnal

A co-deposition of nickel-phosphorus-alumina (NiPA) composite coatings were obtained from an ordinary sulphate-based plating bath consisting of 5 g/l alumina (Al2O3) particles. The particles were dispersed by using mechanical agitation at 125 rpm. The presence of Ni3P and Al2O3 phases in the coatings was confirmed by XRD analysis. SEM/EDX results indicated that a smooth Ni3P coating was obtained and Al2O3 particles were embedded into the coating. Microscopic observation showed that the bonding between the Ni3P metal matrix and the Al2O3 ceramic particles was compact.

Matched MeSH terms: Ceramics
Sintering behaviour of hydroxyapatite bioceramics

Ramesh S, Tan CY, Aw KL, Yeo WH, Hamdi M, Sopyan I, et al.

Med J Malaysia, 2008 Jul;63 Suppl A:89-90.
PMID: 19024998

The sintering behaviour of a commercial HA and synthesized HA was investigated over the temperature range of 700 degrees C to 1400 degrees C in terms of phase stability, bulk density, Young's modulus and Vickers hardness. In the present research, a wet chemical precipitation reaction was successfully employed to synthesize a submicron, highly crystalline, high purity and single phase stoichiometric HA powder that is highly sinteractive particularly at low temperature regimes below 1100 degrees C. It has been revealed that the sinterability of the synthesized HA was significantly greater than that of the commercial HA. The temperature for the onset of sintering and the temperature required to achieve densities above 98% of theoretical value were approximately 150 degrees C lower for the synthesized HA than the equivalent commercial HA. Nevertheless, decomposition of HA phase upon sintering was not observed in the present work for both powders.

Matched MeSH terms: Ceramics/chemistry*
Synthesis and characterization of magnesium doped biphasic calcium phosphate

Toibah AR, Sopyan I, Mel M

Med J Malaysia, 2008 Jul;63 Suppl A:83-4.
PMID: 19024995

The incorporation of magnesium ions into the calcium phosphate structure is of great interest for the development of artificial bone implants. This paper investigates the preparation of magnesium-doped biphasic calcium phosphate (Mg-BCP) via sol gel method at various concentrations of added Mg. The effect of calcinations temperature (ranging from 500 degrees C to 900 degrees C) and concentrations of Mg incorporated into BCP has been studied by the aid of XRD, TGA and infrared spectroscopy (IR) in transmittance mode analysis. The study indicated that the powder was pure BCP and Mg-BCP with 100% purity and high crystallinity. The results also indicated that beta-tricalcium phosphate (beta-TCP) phase can be observed when the powder was calcined at 800 degrees C and above.

Matched MeSH terms: Ceramics/chemistry
Surface properties of Indonesian-made narrow dynamic compression plates

Dewo P, Sharma PK, van der Tas HF, van der Houwen EB, Timmer M, Magetsari R, et al.

Med J Malaysia, 2008 Jul;63 Suppl A:21-2.
PMID: 19024964

The enormous need of orthopaedic (surgical) implants such as osteosynthesis plates is difficult to be fulfilled in developing countries commonly rely on imported ones. One of the alternatives is utilization of local resources, but only after they have been proven safe to use, to overcome this problem. Surface properties are some of the determining factors of safety for those implants. We have succeeded in developing prototype of osteosynthesis plate and the results indicate that Indonesian-made plates need improvement with regards to the surface quality of physical characterization.

Matched MeSH terms: Ceramics

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links