Polypyrrole multi-walled carbon nanotube composite layers were used to modify the gold layer to measure heavy metal ions using the surface plasmon resonance technique. The new sensor was fabricated to detect trace amounts of mercury (Hg), lead (Pb), and iron (Fe) ions. In the present research, the sensitivity of a polypyrrole multi-walled carbon nanotube composite layer and a polypyrrole layer were compared. The application of polypyrrole multi-walled carbon nanotubes enhanced the sensitivity and accuracy of the sensor for detecting ions in an aqueous solution due to the binding of mercury, lead, and iron ions to the sensing layer. The Hg ion bonded to the sensing layer more strongly than did the Pb and Fe ions. The limitation of the sensor was calculated to be about 0.1 ppm, which produced an angle shift in the region of 0.3° to 0.6°.
Polypyrrole (PPy) and polypyrrole-carboxylic functionalized multi wall carbon nanotube composites (PPy/f-MWCNT) were synthesized by in situ chemical oxidative polymerization of pyrrole on the carbon nanotubes (CNTs). The structure of the resulting complex nanotubes was characterized by transmission electron microscopy (TEM) and X-ray diffraction (XRD). The effects of f-MWCNT concentration on the electrical properties of the resulting composites were studied at temperatures between 100 K and 300 K. The Hall mobility and Hall coefficient of PPy and PPy/f-MWCNT composite samples with different concentrations of f-MWCNT were measured using the van der Pauw technique. The mobility decreased slightly with increasing temperature, while the conductivity was dominated by the gradually increasing carrier density.
Zinc sulfide semiconductor nanoparticles were synthesized in an aqueous solution of polyvinyl pyrrolidone via a simple microwave irradiation method. The effect of the polymer concentration and the type of sulfur source on the particle size and dispersion of the final ZnS nanoparticle product was carefully examined. Microwave heating generally occurs by two main mechanisms: dipolar polarization of water and ionic conduction of precursors. The introduction of the polymer affects the heating rate by restriction of the rotational motion of dipole molecules and immobilization of ions. Consequently, our results show that the presence of the polymer strongly affects the nucleation and growth rates of the ZnS nanoparticles and therefore determines the average particle size and the dispersion. Moreover, we found that PVP adsorbed on the surface of the ZnS nanoparticles by interaction of the C-N and C=O with the nanoparticle's surface, thereby affording protection from agglomeration by steric hindrance. Generally, with increasing PVP concentration, mono-dispersed colloidal solutions were obtained and at the optimal PVP concentration (5%), sufficiently small size and narrow size distributions were obtained from both sodium sulfide and thioacetamide sulfur sources. Finally, the sulfur source directly influences the reaction mechanism and the final particle morphology, as well as the average size.
Porous silicon (PSi) layers were formed on a p-type Si wafer. Six samples were anodised electrically with a 30 mA/cm² fixed current density for different etching times. The samples were coated with a 50-60 nm gold layer and annealed at different temperatures under Ar flow. The morphology of the layers, before and after annealing, formed by this method was investigated by scanning electron microscopy (SEM). Photoacoustic spectroscopy (PAS) measurements were carried out to measure the thermal diffusivity (TD) of the PSi and Au/PSi samples. For the Au/PSi samples, the thermal diffusivity was measured before and after annealing to study the effect of annealing. Also to study the aging effect, a comparison was made between freshly annealed samples and samples 30 days after annealing.
The effects of multi-walled carbon nanotube (MWNT) concentration on the structural, optical and electrical properties of conjugated polymer-carbon nanotube composite are discussed. Multi-walled carbon nanotube-polypyrrole nanocomposites were synthesized by electrochemical polymerization of monomers in the presence of different amounts of MWNTs using sodium dodecylbenzensulfonate (SDBS) as surfactant at room temperature and normal pressure. Field emission scanning electron microscopy (FESEM) indicates that the polymer is wrapped around the nanotubes. Measurement of the nonlinear refractive indices (n(2)) and the nonlinear absorption (β) of the samples with different MWNT concentrations measurements were performed by a single Z-scan method using continuous wave (CW) laser beam excitation wavelength of λ = 532 nm. The results show that both nonlinear optical parameters increased with increasing the concentration of MWNTs. The third order nonlinear susceptibilities were also calculated and found to follow the same trend as n(2) and β. In addition, the conductivity of the composite film was found to increase rapidly with the increase in the MWNT concentration.
Nowadays, the application of nanotechnology has gained increased attention in the concrete technology field. Several applications of concrete require light weight; one such concrete used is foamed concrete (FC), which has more voids in the microstructure. In this study, nano-silica (NS) was utilized, which exhibits a pozzolanic nature, and it reacts with other pozzolanic compositions (like lime, alumina, etc.) to form hydrated compounds in concrete. Apart from these hydrated compounds, NS acts as a filler material and enhances properties of concrete such as the fresh and hardened properties. This research examines the fresh, hardened, and microstructural properties of FC blended with NS. The ratio of binder and filler used in this research is 1:1.5, with a water-to-binder ratio of 0.45 and a density of 880 kg/m3. A total of six different weight fractions of NS were added to FC mixes, namely 0%, 1%, 2%, 3%, 4%, and 5%. Properties assessed for FC blended with NS were the slump, bulk density, strength parameters (flexural, splitting tensile, and compressive strengths), morphological analysis, water absorption, and porosity. It was concluded from this study that the optimum NS utilized to improve the properties was 3%. Apart from this, the relationship between the mechanical properties and NS dosages was developed. The correlations between the compressive strength and other properties were analyzed, and relationships were developed based on the best statistical approach. This study helps academicians, researchers, and industrialists enhance the properties of FC blended with NS and their relationships to predict concrete properties from other properties.
Improper waste management is causing global environmental problems. Waste glass may have adverse impacts on the ecosystem. While a substantial amount of soda-lime glass bottle (SGB) undergoes recycling to create new glass items, a significant volume still ends up in landfills. Therefore, the aim of this study was to explore the potential use of SGB in foamed concrete (FC) production as an aggregate replacement. SGB was substituted for sand in different weight fractions, ranging from 5 to 50%. The fresh state, mechanical, thermal, pore structure, and transport properties were examined. The findings showed a significant enhancement in the FC's mechanical properties when SGB replaced 20% of sand. The compressive, flexural, and splitting tensile strengths exhibited a rise of up to 17.7, 39.4, and 43.8%, respectively. The findings also demonstrated that the addition of SGB improved the thermal conductivity, sorptivity, water absorption, and porosity. The scanning electron microscopy analysis indicated that the inclusion of 20% SGB caused a substantial decrease in void diameter and enhanced its uniformity. A comparison was made between the experimental data and predictions of the mechanical properties using various models of international standards, such as IS 456, ACI 318, NZS-3101, EC-02, AS 3600, and CEB-FIB, along with several references in the literature. The findings implied a strong correlation between the strength properties. The outcomes of this research offer valuable insights into both the possible advantages and constraints of using SGB in FC. Furthermore, this extensive laboratory investigation may serve as a guideline for future study and aid in the advancement of greener and more environmentally friendly FC alternatives.
Carbon nanotube (CNT) reinforcement can lead to a new way to enhance the properties of composites by transforming the reinforcement phases into nanoscale fillers. In this study, the buckling response of functionally graded CNT-reinforced composite (FG-CNTRC) sandwich beams was investigated experimentally and analytically. The top and bottom plates of the sandwich beams were composed of carbon fiber laminated composite layers and hard core. The hard core was made of a pultruded glass fiber-reinforced polymer (GFRP) profile. The layers of FG-CNTRC surfaces were reinforced with different proportions of CNT. The reference sample was made of only a pultruded GFRP profile. In the study, the reference sample and four samples with CNT were tested under compression. The largest buckling load difference between the reference sample and the sample with CNT was 37.7%. The difference between the analytical calculation results and experimental results was obtained with an approximation of 0.49%-4.92%. Finally, the buckling, debonding, interlaminar cracks, and fiber breakage were observed in the samples.