MyMedR

Displaying all 11 publications

Abstract:

Sort:

Gold nanoparticles deposited on linker-free silicon substrate and embedded in aluminum Schottky contact

Gorji MS, Razak KA, Cheong KY

J Colloid Interface Sci, 2013 Oct 15;408:220-8.
PMID: 23932085 DOI: 10.1016/j.jcis.2013.07.026

Given the enormous importance of Au nanoparticles (NPs) deposition on Si substrates as the precursor for various applications, we present an alternative approach to deposit Au NPs on linker-free n- and p-type Si substrates. It is demonstrated that, all conditions being similar, there is a significant difference between densities of the deposited NPs on both substrates. The Zeta-potential and polarity of charges surrounding the hydroxylamine reduced seeded growth Au NPs, are determined by a Zetasizer. To investigate the surface properties of Si substrates, contact angle measurement is performed. Field-emission scanning electron microscope is then utilized to distinguish the NPs density on the substrates. Finally, Al/Si Schottky barrier diodes with embedded Au NPs are fabricated, and their structural and electrical characteristics are further evaluated using an energy-filtered transmission electron microscope and current-voltage measurements, respectively. The results reveal that the density of NPs is significantly higher on n-type Si substrate and consequently has more pronounced effects on the electrical characteristics of the diode. It is concluded that protonation of Si-OH group on Si surface in low pH is responsible for the immobilization of Au NPs, which eventually contributes to the lowering of barrier height and enhances the electrical characteristics.
Fulltext Structural and morphology of ZnO nanorods synthesized using ZnO seeded growth hydrothermal method and its properties as UV sensing

Ridhuan NS, Razak KA, Lockman Z, Abdul Aziz A

PLoS One, 2012;7(11):e50405.
PMID: 23189199 DOI: 10.1371/journal.pone.0050405

In this study, zinc oxide (ZnO) nanorod arrays were synthesized using a simple hydrothermal reaction on ZnO seeds/n-silicon substrate. Several parameters were studied, including the heat-treatment temperature to produce ZnO seeds, zinc nitrate concentration, pH of hydrothermal reaction solution, and hydrothermal reaction time. The optimum heat-treatment temperature to produce uniform nanosized ZnO seeds was 400°C. The nanorod dimensions depended on the hydrothermal reaction parameters. The optimum hydrothermal reaction parameters to produce blunt tip-like nanorods (770 nm long and 80 nm in top diameter) were 0.1 M zinc nitrate, pH 7, and 4 h of growth duration. Phase analysis studies showed that all ZnO nanorods exhibited a strong (002) peak. Thus, the ZnO nanorods grew in a c-axis preferred orientation. A strong ultraviolet (UV) emission peak was observed for ZnO nanorods grown under optimized parameters with a low, deep-level emission peak, which indicated high optical property and crystallinity of the nanorods. The produced ZnO nanorods were also tested for their UV-sensing properties. All samples responded to UV light but with different sensing characteristics. Such different responses could be attributed to the high surface-to-volume ratio of the nanorods that correlated with the final ZnO nanorods morphology formed at different synthesis parameters. The sample grown using optimum synthesis parameters showed the highest responsivity of 0.024 A/W for UV light at 375 nm under a 3 V bias.
Fulltext Recent progress of conductive 3D-printed electrodes based upon polymers/carbon nanomaterials using a fused deposition modelling (FDM) method as emerging electrochemical sensing devices

Omar MH, Razak KA, Ab Wahab MN, Hamzah HH

RSC Adv, 2021 Apr 30;11(27):16557-16571.
PMID: 35479129 DOI: 10.1039/d1ra01987b

3D-printing or additive manufacturing is presently an emerging technology in the fourth industrial revolution that promises to reshape traditional manufacturing processes. The electrochemistry field can undoubtedly take advantage of this technology to fabricate electrodes to create a new generation of electrode sensor devices that could replace conventionally manufactured electrodes; glassy carbon, screen-printed carbon and carbon composite electrodes. In the electrochemistry research area, studies to date show that there is a demand for electrically 3D printable conductive polymer/carbon nanomaterial filaments where these materials can be printed out through an extrusion process based upon the fused deposition modelling (FDM) method. FDM could be used to manufacture novel electrochemical 3D printed electrode sensing devices for electrochemical sensor and biosensor applications. This is due to the FDM method being the most affordable 3D printing technique since conductive and non-conductive thermoplastic filaments are commercially available. Therefore, in this minireview, we focus on only the most outstanding studies that have been published since 2018. We believe this to be a highly-valuable research area to the scientific community, both in academia and industry, to enable novel ideas, materials, designs and methods relating to electroanalytical sensing devices to be generated. This approach has the potential to create a new generation of electrochemical sensing devices based upon additive manufacturing. This minireview also provides insight into how the research community could improve the electrochemical performance of 3D-printed electrodes to significantly increase the sensitivity of the 3D-printed electrodes as electrode sensing devices.
Fulltext Production of recombinant Entamoeba histolytica pyruvate phosphate dikinase and its application in a lateral flow dipstick test for amoebic liver abscess

Saidin S, Yunus MH, Zakaria ND, Razak KA, Huat LB, Othman N, et al.

BMC Infect Dis, 2014 Apr 04;14:182.
PMID: 24708664 DOI: 10.1186/1471-2334-14-182

BACKGROUND: Amoebic liver abscess (ALA) is the most common clinical manifestation of extraintestinal amoebiasis especially in developing countries, causing up to 100 000 fatal cases annually. Accurate and early diagnosis is important to prevent the disease complications, however its diagnosis still poses many challenges due to the limitations of the available detection tools. Pyruvate phosphate dikinase (PPDK), an excretory-secretory protein of E. histolytica, has been reported as a potential diagnostic marker for ALA, hence it may be exploited in the development of a new test for ALA.
METHODS: Recombinant PPDK (rPPDK) was expressed, purified and evaluated by Western blot. In parallel, recombinant galactose-and-N-acetyl-D-galactosamine inhibitable lectin (Gal/GalNAc lectin) was produced and tested similarly. The protein identity was confirmed by analysis using MALDI-TOF/TOF. A lateral flow dipstick (LFD) test using rPPDK was subsequently developed (rPPDK-LFD) and evaluated for serodiagnosis of ALA.
RESULTS: rPPDK was expressed as soluble protein after 4 hours of induction with 1 mM isopropyl β-D-1-thiogalactopyranoside (IPTG) at 30°C. Purification using nickel-nitrilotriacetic acid (Ni-NTA) resin yielded 1.5 mg of rPPDK from 1 L of culture with estimated molecular mass of 98 kDa on SDS-PAGE. Western blots using sera from patients with ALA, healthy individuals and other diseases probed with anti-human IgG4-HRP showed the highest sensitivity (93.3%) and specificity (100%); as compared to blots using IgG and IgG1 as secondary antibodies. Moreover, rPPDK showed better specificity when compared to rGal/GalNAc lectin. In the development of the LFD test, the optimum amount of rPPDK was 0.625 μg per dipstick and the optimum working concentration of colloidal gold conjugated anti-human IgG4 was optical density (OD) 5 (1.7 μg of anti-human IgG4). Evaluation of rPPDK-LFD using ALA patients and controls serum samples showed 87% diagnostic sensitivity and 100% specificity.
CONCLUSION: The developed rPPDK-LFD showed good potential for rapid diagnosis of ALA, and merit further multicentre validation using larger number of serum samples.
Fulltext Direct formation of gold nanoparticles on substrates using a novel ZnO sacrificial templated-growth hydrothermal approach and their properties in organic memory device

Goh LP, Razak KA, Ridhuan NS, Cheong KY, Ooi PC, Aw KC

Nanoscale Res Lett, 2012;7(1):563.
PMID: 23046949 DOI: 10.1186/1556-276X-7-563

This study describes a novel fabrication technique to grow gold nanoparticles (AuNPs) directly on seeded ZnO sacrificial template/polymethylsilsesquioxanes (PMSSQ)/Si using low-temperature hydrothermal reaction at 80°C for 4 h. The effect of non-annealing and various annealing temperatures, 200°C, 300°C, and 400°C, of the ZnO-seeded template on AuNP size and distribution was systematically studied. Another PMMSQ layer was spin-coated on AuNPs to study the memory properties of organic insulator-embedded AuNPs. Well-distributed and controllable AuNP sizes were successfully grown directly on the substrate, as observed using a field emission scanning electron microscope followed by an elemental analysis study. A phase analysis study confirmed that the ZnO sacrificial template was eliminated during the hydrothermal reaction. The AuNP formation mechanism using this hydrothermal reaction approach was proposed. In this study, the AuNPs were charge-trapped sites and showed excellent memory effects when embedded in PMSSQ. Optimum memory properties of PMMSQ-embedded AuNPs were obtained for AuNPs synthesized on a seeded ZnO template annealed at 300°C, with 54 electrons trapped per AuNP and excellent current-voltage response between an erased and programmed device.
The effects of size and synthesis methods of gold nanoparticle-conjugated MαHIgG4 for use in an immunochromatographic strip test to detect brugian filariasis

Makhsin SR, Razak KA, Noordin R, Zakaria ND, Chun TS

Nanotechnology, 2012 Dec 14;23(49):495719.
PMID: 23164811 DOI: 10.1088/0957-4484/23/49/495719

This study describes the properties of colloidal gold nanoparticles (AuNPs) with sizes of 20, 30 and 40 nm, which were synthesized using citrate reduction or seeding-growth methods. Likewise, the conjugation of these AuNPs to mouse anti-human IgG(4) (MαHIgG(4)) was evaluated for an immunochromatographic (ICG) strip test to detect brugian filariasis. The morphology of the AuNPs was studied based on the degree of ellipticity (G) of the transmission electron microscopy images. The AuNPs produced using the seeding-growth method showed lower ellipticity (G ≤ 1.11) as compared with the AuNPs synthesized using the citrate reduction method (G ≤ 1.18). Zetasizer analysis showed that the AuNPs that were synthesized using the seeding-growth method were almost monodispersed with a lower polydispersity index (PDI; PDI≤0.079), as compared with the AuNPs synthesized using the citrate reduction method (PDI≤0.177). UV-visible spectroscopic analysis showed a red-shift of the absorbance spectra after the reaction with MαHIgG(4), which indicated that the AuNPs were successfully conjugated. The optimum concentration of the BmR1 recombinant antigen that was immobilized on the surface of the ICG strip on the test line was 1.0 mg ml(-1). When used with the ICG test strip assay and brugian filariasis serum samples, the conjugated AuNPs-MαHIgG(4) synthesized using the seeding-growth method had faster detection times, as compared with the AuNPs synthesized using the citrate reduction method. The 30 nm AuNPs-MαHIgG(4), with an optical density of 4 from the seeding-growth method, demonstrated the best performance for labelling ICG strips because it displayed the best sensitivity and the highest specificity when tested with serum samples from brugian filariasis patients and controls.
Sunlight activated anodic freestanding ZrO2 nanotube arrays for Cr(VI) photoreduction

Bashirom N, Kian TW, Kawamura G, Matsuda A, Razak KA, Lockman Z

Nanotechnology, 2018 Sep 14;29(37):375701.
PMID: 29901455 DOI: 10.1088/1361-6528/aaccbd

Visible-light-active freestanding zirconia (ZrO2) nanotube (FSZNT) arrays were fabricated by a facile electrochemical anodization method in fluoride containing ethylene glycol electrolyte added to it was 1 vol% of potassium carbonate (K2CO3) at 60 V for 1 h. Poor adhesion at the metal∣oxide interface was induced by K2CO3 leading to the formation of FSZNT flakes. The effect of the crystal structures of the FSZNTs e.g., amorphous, amorphous/tetragonal, and tetragonal/monoclinic was investigated towards the photocatalytic reduction of 10 ppm hexavalent chromium, Cr(VI) at pH 2 under sunlight. The results demonstrate the amorphous FSZNTs exhibited the highest Cr(VI) removal efficiency than the crystalline FSZNTs (95% versus 33% after 5 h). The high photocatalytic activity of the amorphous FSZNTs can be attributed to enhanced Cr(VI) adsorption, high visible light absorption, and better charge carrier separation. The low photocatalytic activity of the crystalline FSZNTs annealed at 500 °C was mainly attributed to poor Cr(VI) adsorption, low visible light absorption, and less photoactive monoclinic-ZrO2.
Formation of grassy TiO2 nanotube thin film by anodisation in peroxide electrolyte for Cr(VI) removal under ultraviolet radiation

Taib MAA, Alias N, Jaafar M, Razak KA, Tan WK, Shahbudin IP, et al.

Nanotechnology, 2020 Oct 23;31(43):435605.
PMID: 32640434 DOI: 10.1088/1361-6528/aba3d8

Arrays of TiO2 nanotubes (TiO2 NTs) with grassy surfaces were observed on titanium foil anodised at 60 V in fluorinated ethylene glycol (EG) with added hydrogen peroxide (H2O2). The grassy surface was generated by the chemical etching and dissolution of the surface of the TiO2 NTs walls, which was accelerated by the temperature increase on the addition of H2O2 . Upon annealing at 600 °C, the grassy part of the TiO2 NTs was found to consist of mostly anatase TiO2 whereas the bottom part of the anodic oxide comprised a mixture of anatase and rutile TiO2. The TiO2 NTs were then used to reduce hexavalent chromium (Cr(VI)) under ultraviolet radiation. They exhibited a rather efficient photocatalytic effect, with 100% removal of Cr(VI) after 30 min of irradiation. The fast removal of Cr(VI) was due to the anatase dominance at the grassy part of the TiO2 NTs as well as the higher surface area the structure may have. This work provides a novel insight into the photocatalytic reduction of Cr(VI) on grassy anatase TiO2 NTs.
Massive Traumatic Skin Defect Successfully Treated with Autologous, Bilayered, Tissue-Engineered MyDerm Skin Substitute: A Case Report

Mohamed Haflah NH, Ng MH, Mohd Yunus MH, Naicker AS, Htwe O, Abdul Razak KA, et al.

JBJS Case Connect, 2018 6 15;8(2):e38.
PMID: 29901479 DOI: 10.2106/JBJS.CC.17.00250

CASE: A 22-year-old man sustained a laceration that measured 180 cm, after debridement, over the anterolateral aspect of the right leg following a road traffic accident. The wound was treated with MyDerm (Universiti Kebangsaan Malaysia), a cell-based, bilayered, bioengineered dermal substitute that contains no animal-derived components and is fully autologous. For its construction, only a small area of skin was harvested from the left groin, which was closed primarily with absorbable sutures.
CONCLUSION: MyDerm is an alternative option for the treatment of a massive skin defect in patients who desire removal of only a negligible amount of skin from the donor site and when use of an autograft is insufficient.
Fulltext The Effect of Polyethylene Glycol Addition on Wettability and Optical Properties of GO/TiO2 Thin Film

Azani A, Halin DSC, Razak KA, Abdullah MMAB, Nabiałek M, Ramli MM, et al.

Materials (Basel), 2021 Aug 13;14(16).
PMID: 34443086 DOI: 10.3390/ma14164564

Modification has been made to TiO2 thin film to improve the wettability and the absorption of light. The sol-gel spin coating method was successfully used to synthesize GO/TiO2 thin films using a titanium (IV) isopropoxide (TTIP) as a precursor. Different amounts of polyethylene glycol (PEG) (20 to 100 mg) were added into the parent sol solution to improve the optical properties and wettability of the GO/TiO2 thin film. The effect of different amounts of PEG was characterized using X-ray diffraction (XRD) for the phase composition, scanning electron microscopy (SEM) for microstructure observation, atomic force microscopy (AFM) for the surface topography, ultraviolet-visible spectrophotometry (UV-VIS) for the optical properties and wettability of the thin films by measuring the water contact angle. The XRD analysis showed the amorphous phase. The SEM and AFM images revealed that the particles were less agglomerated and surface roughness increases from 1.21 × 102 to 2.63 × 102 nm when the amount of PEG increased. The wettability analysis results show that the water contact angle of the thin film decreased to 27.52° with the increase of PEG to 80 mg which indicated that the thin film has hydrophilic properties. The optical properties also improved significantly, where the light absorbance wavelength became wider and the band gap was reduced from 3.31 to 2.82 eV with the presence of PEG.
Micro-interdigitated electrodes genosensor based on Au-deposited nanoparticles for early detection of cervical cancer

Jaapar FN, Parmin NA, Halim NHA, Hashim U, Gopinath SCB, Halim FS, et al.

Int J Biol Macromol, 2023 Dec 31;253(Pt 2):126745.
PMID: 37689297 DOI: 10.1016/j.ijbiomac.2023.126745

Genosensor-based electrodes mediated with nanoparticles (NPs) have tremendously developed in medical diagnosis. Herein, we report a facile, rapid, low cost and highly sensitive biosensing strategy for early detection of HPV 18 using gold-nanoparticles (AuNPs) deposited on micro-IDEs. This study represents surface charge transduction of micro-interdigitated electrodes (micro-IDE) alumina insulated with silica, independent and mini genosensor modified with colloidal gold NPs (AuNPs), and determination of gene hybridization for early detection of cervical cancer. The surface of AuNPs deposited micro-IDE functionalized with optimized 3-aminopropyl-triethoxysilane (APTES) followed by hybridization with deoxyribonucleic acid (DNA) virus to develop DNA genosensor. The results of ssDNA hybridization with the ssDNA target of human papillomavirus (HPV) 18 have affirmed that micro-IDE functionalized with colloidal AuNPs resulted in the lowest detection at 0.529 aM. Based on coefficient regression, micro-IDE functionalized with AuNPs produces better results in the sensitivity test (R2 = 0.99793) than unfunctionalized micro-IDE.

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links