Displaying publications 1 - 20 of 22 in total

Abstract:
Sort:
  1. Salimon J, Salih N, Yousif E
    J Oleo Sci, 2011;60(12):613-8.
    PMID: 22123242
    Petroleum is a finite source as well as causing several environmental problems. Therefore petroleum needs to be replaced by alternative and sustainable sources. Plant oils and oleochemicals derived from them represent such alternative sources; the use of oleochemicals as biobased lubricants is of significant interest. This article presents a series of chemical modification on oleic acid to yield synthetic biolubricant basestocks. Measuring of density, volatility, cloud point (CP), pour point (PP), flash point (FP), viscosity index (VI), onset temperature (OT) and signal maximum temperature (SMT) was carried out for each compound. Furthermore, the friction and wear properties were measured using high-frequency reciprocating rig (HFRR). The results showed that octadecyl 9-octadecyloxy-10-hydroxyoctadecanoate exhibited the most favorable low-temperature performance (CP %ndash;26°C, PP %ndash;28°C) and the lowest ball wear scan diameter (42 µm) while propyl 9-propyloxy-10-hydroxyoctadecanoate exhibited the higher oxidation stability (OT 156°C).
    Matched MeSH terms: Chemistry, Physical
  2. Kang K, Nanda S, Lam SS, Zhang T, Huo L, Zhao L
    Environ Res, 2020 07;186:109480.
    PMID: 32302869 DOI: 10.1016/j.envres.2020.109480
    Microwave assisted hydrothermal treatment (MHTC) was compared with torrefaction in terms of carbonization efficiency and physicochemical characteristics of char products. The utilization of produced char was optimized for composite solid biofuel production. The results show that MHTC significantly improved the binding capability of the microwave hydrochar (MHC) particles during co-densification with unprocessed biomass and coal. One possible contributor to the improved binding is the pseudo lignin formed during the MHTC, which led to a better interlocking of the feedstock particles and promoted the solid bridge formation. Composite pellet prepared with 80 wt% of torrefaction char (TC-120), 10 wt% of microwave hydrochar (MHC-30), and 10 wt% of Coal-04 showed a higher heating value of 24.54 MJ/kg and energy density of 26.43 GJ/m3, which is significantly higher than that of the raw cotton stalk pellet (16.77 MJ/kg and 18.76 GJ/m3, respectively), showing great promise as a solid biofuel. The moisture resistance and oxidation reactivity are also significantly improved. The results demonstrate that MHCs provides dual functionalities in acting as binder and fuel promoter in the production of composite biofuel. This study can provide new insight into the unique functions of MHC during fuel application, which demonstrates the great potential of applying MHTC in energy recovery from lignocellulosic biomass.
    Matched MeSH terms: Chemistry, Physical
  3. Talib R
    J Nihon Univ Sch Dent, 1993 Sep;35(3):161-70.
    PMID: 8246037
    Dental composite resins are widely used in dental practice and are continually being developed in order to obtain better products. To gain full benefit from these materials, it is important for the clinician to understand their properties. The following is a review of the more common characteristics of composites in current use.
    Matched MeSH terms: Chemistry, Physical
  4. Ahmad N, Ramsch R, Esquena J, Solans C, Tajuddin HA, Hashim R
    Langmuir, 2012 Feb 7;28(5):2395-403.
    PMID: 22168405 DOI: 10.1021/la203736b
    Synthetic branched-chain glycolipids have become of great interest in biomimicking research, since they provide a suitable alternative for natural glycolipids, which are difficult to extract from natural resources. Therefore, branched-chain glycolipids obtained by direct syntheses are of utmost interest. In this work, two new branched-chain glycolipids are presented, namely, 2-hexyldecyl β(α)-D-glucoside (2-HDG) and 2-hexyldecyl β(α)-D-maltoside (2-HDM) based on glucose and maltose, respectively. The self-assembly properties of these glycolipids have been studied, observing the phase behavior under thermotropic and lyotropic conditions. Due to their amphiphilic characteristics, 2-HDG and 2-HDM possess rich phase behavior in dry form and in aqueous dispersions. In the thermotropic study, 2-HDG formed a columnar hexagonal liquid crystalline phase, whereas in a binary aqueous system, 2-HDG formed an inverted hexagonal liquid crystalline phase in equilibrium with excess aqueous solution. Furthermore, aqueous dispersions of the hexagonal liquid crystal could be obtained, dispersions known as hexosomes. On the other hand, 2-HDM formed a lamellar liquid crystalline phase (smectic A) in thermotropic conditions, whereas multilamellar vesicles have been observed in equilibrium with aqueous media. Surprisingly, 2-HDM mixed with sodium dodecyl sulfate or aerosol OT induced the formation of more stable unilamellar vesicles. Thus, the branched-chain glycolipids 2-HDG and 2-HDM not only provided alternative nonionic surfactants with rich phase behavior and versatile nanostructures, but also could be used as new drug carrier systems in the future.
    Matched MeSH terms: Chemistry, Physical
  5. Mohd Din AT, Hameed BH, Ahmad AL
    J Hazard Mater, 2009 Jan 30;161(2-3):1522-9.
    PMID: 18562090 DOI: 10.1016/j.jhazmat.2008.05.009
    The liquid-phase adsorption of phenol onto coconut shell-based activated carbon, CS850A was investigated for its equilibrium studies and kinetic modeling. Coconut shell was converted into high quality activated carbon through physiochemical activation at 850 degrees C under the influence of CO(2) flow. Beforehand, the coconut shell was carbonized at 700 degrees C and the resulted char was impregnated with KOH at 1:1 weight ratio. In order to evaluate the performance of CS850A, a series of batch adsorption experiments were conducted with initial phenol concentrations ranging from 100 to 500 mg l(-1), adsorbent loading of 0.2g and the adsorption process was maintained at 30+/-1 degrees C. The adsorption isotherms were in conformation to both Langmuir and Freundlich isotherm models. Chemical reaction was found to be a rate-controlling parameter to this phenol-CS850A batch adsorption system due to strong agreement with the pseudo-second-order kinetic model. Adsorption capacity for CS850A was found to be 205.8 mg g(-1).
    Matched MeSH terms: Chemistry, Physical/methods
  6. Agatonovic-Kustrin S, Beresford R, Yusof AP
    J Pharm Biomed Anal, 2001 May;25(2):227-37.
    PMID: 11275432
    A quantitative structure-human intestinal absorption relationship was developed using artificial neural network (ANN) modeling. A set of 86 drug compounds and their experimentally-derived intestinal absorption values used in this study was gathered from the literature and a total of 57 global molecular descriptors, including constitutional, topological, chemical, geometrical and quantum chemical descriptors, calculated for each compound. A supervised network with radial basis transfer function was used to correlate calculated molecular descriptors with experimentally-derived measures of human intestinal absorption. A genetic algorithm was then used to select important molecular descriptors. Intestinal absorption values (IA%) were used as the ANN's output and calculated molecular descriptors as the inputs. The best genetic neural network (GNN) model with 15 input descriptors was chosen, and the significance of the selected descriptors for intestinal absorption examined. Results obtained with the model that was developed indicate that lipophilicity, conformational stability and inter-molecular interactions (polarity, and hydrogen bonding) have the largest impact on intestinal absorption.
    Matched MeSH terms: Chemistry, Physical
  7. Babji AS, Chin SY, Seri Chempaka MY, Alina AR
    Int J Food Sci Nutr, 1998 Sep;49(5):319-26.
    PMID: 10367000
    Four formulations were processed into frankfurters with different ratios of mechanically deboned chicken meat (MDCM) and cooked chicken skin (CCS) i.e. 80/0, 70/10, 60/20 and 50/30. The products were evaluated for proximate composition, cholesterol content, colour; 'L' value (lightness) and 'a' value (redness), percentage of cooking loss, physical measurements (shearforce-kgf and folding test), thiobarbituric acid value (TBA) and taste panel evaluation. The increment of CCS in the frankfurters increased the contents of moisture, ash, protein, fat, cholesterol, the lightness ('L' value) and redness ('a' value). After 3 months of frozen storage, the increment continued except for the moisture contents for formulations with 20 and 30% CCS. The lipid oxidation (TBA value) and cooking loss were lowered in formulations with CCS. After 3 months of frozen storage, TBA value decreased, while the cooking loss increased for all the formulations. The addition of CCS increased hardness of the frankfurters but affected folding ability, with formulation with 10% CCS scoring better grade. Sensory evaluation was carried out using 30 untrained panelists to evaluate aroma, colour, appearance, hardness, juiciness, chicken taste, oily taste, rancid taste and overall acceptance of the products. The addition of CCS in the frankfurters at 10 and 20% resulted in products with taste and texture that were acceptable after 3 months of frozen storage.
    Matched MeSH terms: Chemistry, Physical
  8. Ismail BS, Quirinus L
    Bull Environ Contam Toxicol, 2000 Oct;65(4):530-6.
    PMID: 10960146
    Matched MeSH terms: Chemistry, Physical
  9. Salman JM, Hameed BH
    J Hazard Mater, 2010 Mar 15;175(1-3):133-7.
    PMID: 19879687 DOI: 10.1016/j.jhazmat.2009.09.139
    Oil palm fronds (OPF) were used to prepare activated carbon (PFAC) using physiochemical activation method, which consisted of potassium hydroxide (KOH) treatment and carbon dioxide gasification. The effects of the preparation variables, which were activation temperature, activation time and chemical impregnation ratios (KOH: char by weight), on the carbon yield and bentazon removal were investigated. Based on the central composite design (CCD), two factor interaction (2FI) and quadratic models were, respectively, employed to correlate the PFAC preparation variables to the bentazon removal and carbon yield. From the analysis of variance (ANOVA), the most influential factor on each experimental design response was identified. The optimum conditions for preparing activated carbon from OPF were found as follows: activation temperature of 850 degrees C, activation time of 1h and KOH:char ratio of 3.75:1. The predicted and experimental results for removal of bentazon and yield of PFAC were 99.85%, 20.5 and 98.1%, 21.6%, respectively.
    Matched MeSH terms: Chemistry, Physical/methods
  10. Karim AA, Toon LC, Lee VP, Ong WY, Fazilah A, Noda T
    J Food Sci, 2007 Mar;72(2):C132-8.
    PMID: 17995828
    Effects of phosphorus content (510 to 987 ppm) on the gelatinization and retrogradation of 6 potato cultivars (Benimaru, Hokkaikogane, Irish Cobbler, Konafubuki, Sakurafubuki, and Touya) were studied. Pasting properties were analyzed by RVA, thermal properties by DSC, and mechanical properties of the starch gels by TA. Phosphorus was positively correlated with swelling power (r= 0.84) and negatively correlated with solubility (r= 0.83). Phosphorus content showed significant effect on certain pasting properties of potato starch such as peak viscosity, breakdown, and setback. Phosphorus content showed a significant positive correlation with peak viscosity (r= 0.95) and breakdown (r= 0.90). Increasing concentration of phosphorus tends to decrease the setback. Phosphorus content had no influence on thermal properties and mechanical properties of potato starch gel.
    Matched MeSH terms: Chemistry, Physical
  11. Vakhrusheva T, Panasenko O
    Chem Phys Lipids, 2006 Apr;140(1-2):18-27.
    PMID: 16458872
    In this work, we studied whether chondroitin sulfates and dextran sulfates (DXSs) can influence hypochlorite-induced peroxidation of phosphatidylcholine (PC) liposomes. Multilamellar liposomes (2 mg lipid/ml) were prepared in phosphate buffer, pH 7.4, with NaCl or not and exposed to reagent HOCl/ClO- (1mM) at 37 degrees C in the presence of different concentrations of chondroitin 6-sulfate (C6S), chondroitin 4-sulfate (C4S), DXS 8000, DXS 40,000, and DXS 500,000. Lipid peroxidation was assessed by thiobarbituric acid-reactive substance (TBARS) production. DXSs and C6S enhanced TBARS production in a dose-dependent manner. The decline in TBARS production at the relatively high C6S concentrations may be attributed to C4S present in C6S, since in contrast to C6S, C4S is known to react with hypochlorite. Dextrans, nonsulfated analogues of DXS, failed to modulate TBARS production. This fact indicates the important role of negatively charged sulfate groups for DXS to facilitate hypochlorite-induced peroxidation of PC liposomes. The electrostatic nature of the mechanism providing for the pro-oxidative effect of DXS was also supported by the influence of liposome surface charge and solution ionic strength on the extent of liposome peroxidation. The addition of calcium ions to the incubation mixture did not prevent the pro-oxidative action of DXS. The relevance of the results to atherogenesis is discussed.
    Matched MeSH terms: Chemistry, Physical
  12. Miskandar MS, Man YC, Yusoff MS, Rahman RA
    Asia Pac J Clin Nutr, 2005;14(4):387-95.
    PMID: 16326646
    Optimum processing conditions on palm oil-based formulations are required to produce the desired quality margarine. As oils and fats contribute to the overall property of the margarine, this paper will review the importance of beta' tending oils and fats in margarine formulation, effects of the processing parameters -- emulsion temperature, flow-rate, product temperature and pin-worker speed -- on palm oil margarines produced and their subsequent behaviour in storage. Palm oil, which contributes the beta' crystal polymorph and the best alternative to hydrogenated liquid fats, and the processing conditions can affect the margarine consistency by influencing the solid fat content (SFC) and the types of crystal polymorph formed during production as well as in storage. Palm oil, or hydrogenated palm oil and olein, in mixture with oils of beta tending, can veer the product to the beta' crystal form. However, merely having beta' crystal tending oils is not sufficient as the processing conditions are also important. The emulsion temperature had no significant effect on the consistency and polymorphic changes of the product during storage, even though differences were observed during processing. The consistency of margarine during storage was high at low emulsion flow-rates and low at high flow rates. The temperature of the scraped-surface tube-cooler is the most important parameter in margarine processing. High temperature will produce a hardened product with formation of beta-crystals during storage. The speed of the pin-worker is responsible for inducing crystallization but, at the same time, destroys the crystal agglomerates, resulting in melting.
    Matched MeSH terms: Chemistry, Physical
  13. Elkanzi EM, Bee Kheng G
    J Hazard Mater, 2000 Mar 13;73(1):55-62.
    PMID: 10686378
    Hydrogen peroxide and UV radiation have been used in the photochemical degradation of isoprene in aqueous solutions. A kinetic study is carried out taking into account the contribution of the UV radiation reaction and the combined reaction with hydrogen peroxide. An empirical reaction rate expression, which considers the two reactions taking place in parallel, is suggested. Pseudo-first order rate constants are obtained from batch reactor data. As the molar ratio of H(2)O(2):isoprene increases, the rate of reaction increases linearly while the concentration of H(2)O(2) is observed to be nearly constant throughout the reaction; suggesting that the H(2)O(2) acts as a pseudo-catalyst. Nearly complete oxidation of isoprene is achieved. These results indicate that the H(2)O(2)/UV process appears to be a competitive alternative destructive treatment for removing isoprene from water present at low levels.
    Matched MeSH terms: Chemistry, Physical
  14. Cao SG, Sim KY, Goh SH
    Nat Prod Lett, 2001;15(5):291-7.
    PMID: 11841112
    Two new biflavonoids, pyranoamentoflavone 7-methyl ether (1) and pyranoamentoflavone 4'-methyl ether (2), have been isolated from the leaves of Calophyllum venulosum. The structures of these two new compounds were elucidated by spectroscopic data.
    Matched MeSH terms: Chemistry, Physical
  15. Ahmad M, Roy RA
    Endod Dent Traumatol, 1994 Apr;10(2):71-6.
    PMID: 8062810
    The incidence of breakage of Piezon-Master ultrasonic K files were evaluated. Three groups of unused files were subjected to three treatments, namely; free vibration in air without irrigation, free vibration in root canal while minimizing contact with the wall of canal in the presence of irrigation and light filing in root canal with free flow of irrigation. Cavitation produced by files in contact and free of contact with a glass surface was examined in order to observe the relationship between cavitation defects and breakage. In addition, the fractured and unfractured files were examined under a scanning electron microscope for the presence of cavitation pits. The results indicated that more files broke in air. In water, a higher incidence of breakage occurred when files were allowed to freely vibrate while no breakage occurred when the files were used in filing. All files generated cavitation which resulted in pitting of their surfaces. However, it was considered unlikely that the pits contributed to fracture. Fatigue cracks which could be the result of the manufacturing process were observed at some of the corners of the cross sections of the fractured files and could be the main contributory factor to fracture.
    Matched MeSH terms: Chemistry, Physical
  16. Idris NA, Dian NL
    Asia Pac J Clin Nutr, 2005;14(4):396-401.
    PMID: 16326647
    Inter-esterification is one of the processes used to modify the physico-chemical characteristics of oils and fats. Inter-esterification is an acyl-rearrangement reaction on the glycerol molecule. On the other hand, hydrogenation involves addition of hydrogen to the double bonds of unsaturated fatty acids. Due to health implications of trans fatty acids, which are formed during hydrogenation, the industry needs to find alternatives to hydrogenated fats. This paper discusses some applications of inter-esterified fats, with particular reference to inter-esterified palm products, as alternatives to hydrogenation. Some physico-chemical properties of inter-esterified fats used in shortenings are discussed. With inter-esterification, more palm stearin can be incorporated in vanaspati. For confectionary fats and infant formulations, enzymatic inter-esterification has been employed.
    Matched MeSH terms: Chemistry, Physical
  17. Amin MC, Fell JT
    Drug Dev Ind Pharm, 2004;30(9):937-45.
    PMID: 15554218
    Percolation theory has been used with great interest in understanding the design and characterization of dosage forms. In this study, work has been carried out to investigate the behavior of binary mixture tablets containing excipients of similar and different deformation properties. The binary mixture tablets were prepared by direct compression using lactose, polyvinyl chloride (PVC), Eudragit RS 100, and microcrystalline cellulose (MCC). The application of percolation theory on the relationships between compactibility, Pmax, or compression susceptibility (compressibility), gamma, and mixture compositions reveals the presence of percolation thresholds even for mixtures of similar deformation properties. The results showed that all mixture compositions exhibited at least one discreet change in the slope, which was referred to as the percolation threshold. The PVC/Eudragit RS100 mixture compositions showed significant percolation threshold at 80% (w/w) PVC loading. Two percolation thresholds were observed from a series of binary mixtures containing similar plastic deformation materials (PVC/MCC). The percolation thresholds were determined at 20% (w/w) and 80% (w/w) PVC loading. These are areas where one of the components percolates throughout the system and the properties of the tablets are expected to experience a sudden change. Experimental results, however, showed that total disruption of the tablet physical properties at the specified percolation thresholds can be observed for PVC/lactose mixtures at 20-30% (w/w) loading while only minor changes in the tablets' strength for PVC/MCC or PVC/Eudragit RS 100 mixtures were observed.
    Matched MeSH terms: Chemistry, Physical
  18. Lee KH, Lee PM, Siaw YS
    J Chem Technol Biotechnol, 1993;57(1):27-32.
    PMID: 7763683
    Aminoacylase I (EC 3.5.1.14) encapsulated in calcium alginate beads stabilized with poly-L-lysine was used for the production of L-phenylalanine by the hydrolysis of a racemic mixture of N-acetyl-DL-phenylalanine. The immobilized aminoacylase was studied with respect to operational stability, thermal stability, effects of pH and temperature and kinetic constants. The leakage of enzyme from the stabilized beads was eliminated. The immobilized enzyme retained high biological activity. The Km and Vmax values for the stabilized beads were 11.11 mmol dm-3 and 0.076 mumol min-1 respectively. The optimum pH and temperature for the hydrolysis were 6.5 and 55 degrees C respectively. Scanning electron micrographs revealed crosslinked structures on the surface of the beads. The operational performances of the beads in a batch reaction and a packed-bed bioreactor for continuous reaction were investigated. With batch reaction, only about 5% of enzyme activity was lost within ten reaction cycles and there was no significant loss of activity over 600 h of continuous operation after equilibrium was reached, and a conversion yield of about 80% was obtained.
    Matched MeSH terms: Chemistry, Physical
  19. Memon MS, Yunus N, Razak AA
    Int J Prosthodont, 2001 May-Jun;14(3):214-8.
    PMID: 11484567
    PURPOSE: The impact strength and the flexural properties of denture base materials are of importance in predicting their clinical performance upon sudden loading. This study compares the impact and transverse strengths and the flexural modulus of three denture base polymers.
    MATERIALS AND METHODS: The investigation included a relatively new microwave-polymerized polyurethane-based denture material processed by an injection-molding technique, a conventional microwave-polymerized denture material, and a heat-polymerized compression-molded poly(methyl methacrylate) (PMMA) denture material. Impact strength was determined using a Charpy-type impact tester. The transverse strength and the flexural modulus were assessed with a three-point bending test. The results were subjected to statistical analysis using a one-way analysis of variance and the Scheffé test for comparison.
    RESULTS: The impact strength of the microwave-polymerized injection-molded polymer was 6.3 kl/m2, while its flexural strength was 66.2 MPa. These values were lower than those shown by the two compression-molded PMMA-based polymers. The differences were statistically significant. The flexural modulus of the new denture material was 2,832 MPa, which was higher than the conventional heat-polymerized polymer but was comparable to the other microwave-polymerized PMMA-based polymer. The difference in the flexural modulus was statistically significant.
    CONCLUSION: In terms of the impact and flexural strengths, the new microwave-polymerized, injection-molded, polyurethane-based polymer offered no advantage over the existing heat- and microwave-polymerized PMMA-based denture base polymers. However, it has a rigidity comparable to that of the microwave-polymerized PMMA polymer.
    Matched MeSH terms: Chemistry, Physical
  20. Tarafder MT, Kasbollah A, Saravanan N, Crouse KA, Ali AM, Tin Oo K
    J. Biochem. Mol. Biol. Biophys., 2002 Apr;6(2):85-91.
    PMID: 12186762
    Eight selective nitrogen-sulfur donor ligands have been synthesized from the condensation of S-methyldithiocarbazate (SMDTC) with aldehydes and ketones with a view to evaluating their antimicrobial and cytotoxic activities, and also to correlate the biological properties with the structure of the ligands. The compounds were all characterized by elemental analyses and other physicochemical techniques. SMDTC and the Schiff bases were screened for antimicrobial and cytotoxic activities. SMDTC showed very large inhibition zones (24-44 mm) against bacteria and fungi with a minimum inhibitory concentration (MIC) of 390-25,000 and 1562-6250 microg ml(-1), against different bacteria and fungi, respectively. Streptomycin and nystatin were used as the internal standards against bacteria and fungi, respectively. SMDTC along with its Schiff bases with pyridine-2-carboxaldehyde, acetylacetone and 2,3-butanedione were strongly antifungal and the MIC values were comparable to nystatin. Most of the Schiff bases were strongly cytotoxic. In particular, those with pyridine-2-carboxaldehyde and 2,3-butanedione have CD(50) values of 5.5, 1.9-2.0 microg ml(-1), respectively, against leukemic cells, while against colon cancer cells, the values were 3.7 and 2.0 microg ml(-1), respectively. The glyoxal Schiff base was strongly active only against leukemic cell with CD(50) value of 4.0 microg ml(-1). The present findings have been compared with standard drugs.
    Matched MeSH terms: Chemistry, Physical
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links