This article uses finite volume and finite element methods for optimization of the artificial hair cell sensor. The performance of the sensor was investigated for different materials such as sicon and polysilicon and by varying hair cell dimensions including width and length. The silicon material which has low young modulus was proposed based on the simulation performance. The performance of the hair cell sensor was achieved by increasing the hair cell length while increasing the width did not significantly influence the performance. The
performance of the sensor was studied for its viscous force, deflection, von mises stress and sensitivity. From the simulation, the hair cell with a length of 1600 µm and 80 µm width was suggested for the subsequent analysis. Another way to improve the performance was by modifying the hair cell geometry and it was proved that the modified hair cell was more sensitive, based on the deflection. The angle of flow that hit the hair cell also affected the deflection of the sensor where the zero angle flow which was parallel to the substrate was the most effective angle. The limitations of the performance of hair cell for various fluid velocity were also discussed in this paper.
The paper seeks to assuage the fears and worries over living modified organisms (LMOs). It describes how any research carried out on LMOs as well as any release activity on LMOs for public use in Malaysia is controlled by the Biosafety Act 2007. Stringent risk assessment of the LMO and its product/s is carried out to eradicate or minimize the negative effects of these on animal and human health, and to biological diversity and the environment. In contrast, no such risk assessment is carried out on introduced exotic species, or on the products of other types of technology, with the exception of pharmaceuticals. Examples are given comparing risk assessment on LMOs and exotic species.
Nowadays, construction and demolition waste has become a major issue to environmental problems faced by many countries. This concern comes from the inefficiencies of waste management which includes the waste generated from construction and demolition activities. In Malaysia, there is a lack of database records on construction waste and this has affected proper management planning of the waste. As there is a lack of policy on construction waste management, control on construction waste disposal is very hazy and this has aggravated environmental problems and exhausted landfill usage and increased illegal dumping. This paper reviews the critical issues on construction waste management and also discusses several estimation models on construction waste generation from several countries. Based on the review, most of the countries faced problems regarding construction waste management and the models developed were considered as one of the methods which could be adopted for better management of construction wastes.
Molecular markers have been intensively used in assisting breeding to reduce the time taken by conventional breeding as well as helping introgression of specific traits. Baseline analysis of known markers is crucial in developing a genetic database on disease and pest resistance for local rice germplasm which does not yet
exist. In this study seven local rice varieties, including the popular MR219 and MRQ 74 and MRQ 76 (newly developed aromatic rice varieties), together with a foreign variety, Intani-2, were screened for genetic markers related to pest and disease resistance. One hundred and twenty-two type-related markers (SSR, STS, InDel and Allele-specific) for genes resistant to bacterial leaf blight, blast and brown planthopper were screened using PCR amplification and validated by sequencing. It was found that each variety had its own pattern of resistance. Using allele-specific markers namely pBPH9, pTA248 and Pisbdom were found to be the most efficient way to screen for the targeted genes. Of the seven varieties, MR219 and MR232 were found to have the highest distribution of markers for resistance genes against pest and diseases studied.
Throughout the years, the construction industry has made an important contribution to the Malaysian economy. Moreover, the Ninth Malaysia Plan (2006–2010) has also played a significant role in the demands of executing major residential housing project developments where it has been observed that construction waste was one of the priority waste streams. Due to the increasing number in the population that is actively involved in economic activities, and the modernization of the country, the types of construction waste that are being produced, and identifying the source such as waste are becoming more complex. Therefore, appropriate actions and approaches are needed to be taken with respect to its effective management in handling the solid waste from construction sites. This paper is intended to review the issues and the challenges enclosed within the supply chain management mechanisms in order for improving construction waste management. Throughout this review, useful information and better understanding concerning the current issues, challenges and the supply chain management mechanisms would be made inclusive in the field to be explored. The findings would also assist in improving the quality and awareness on the construction waste management that is being practiced.
MeSH terms: Awareness; Housing; Malaysia; Paper; Social Change; Waste Management; Neuroaxonal Dystrophies; Construction Industry; Solid Waste
This study investigated the thermal properties of three room temperature curing adhesives containing nano particles which were thixotropic and shear thinning which allowed injection into overhead holes when exposed to different environmental conditions. Viscosity and shear stress of the adhesives were measured as a function of shear rate. The thermal behaviour of the adhesives were measured using dynamic mechanical thermal anylisis following exposures to different temperatures and humidities which included temperatures of 20 degrees Celcius, 30 degrees Celcius and 50 degrees Celcius, relative humidities of 65% RH, 75% RH 95% RH soaked in water at 20 degrees Celcius and placed in the oven at 50 degrees Celcius. The dynamic thermal properties reported include storage and loss modulus, the loss tangent and the glass transition temperature ( Tg ). For nano- and micro-particles filled adhesives, the Tg increased with the temperature increase, even though the adhesives was subjected to high humidity and this was due to further cross-linking. The results showed that room temperature cured epoxies were only partially cured at room temperature.
Measurement of low magnetic field has played an important role in many electronics applications such as navigation, military, non-destructive test, traffic detection as well as medical diagnosis and treatment. The presence of magnetic field, particularly its strength and direction, can be measured using magnetometer. There are many types of magnetometers being investigated through the years and one of the prominent types is fluxgate magnetometer. The main components of fluxgate magnetometer consisting of driving coils, sensing coils and magnetic core are developed by MEMS silicon processing technology. In this paper, an investigation on physical characteristics of the three-dimensional coil structure for a micro-scaled fluxgate magnetometer is presented. The physical characteristics such as width of the coil, distance between successive coils, and gap between the top and bottom coils which would influence the magnetic energy in magnetometer is discussed. In this work, finite-element method simulations to investigate the physical characteristics of the sensing coils were carried out, where the parameter of interest is the coils’ inductance as well as the magnetic flux density. Based on the simulation results, the varying of physical characteristics of the coils had its effects particularly in coil inductance, magnetic flux density, and magnetic energy. It could also be seen that the simulated results agreed with the theoretical aspects of magnetism in a coil. From the investigations, suitable coil dimensions were proposed.
MeSH terms: Electronics; Magnetics; Military Personnel; Physical Examination; Silicon; Micro-Electrical-Mechanical Systems; Magnetic Fields
Widespread deforestation has resulted in soil degradation that is often linked to environmental and ecological changes. Rehabilitation of degraded forest is essential to prevent further degradation of the soil. Abundance of soil microbiota could serve as an essential biological indicator of soil health for rehabilitation success. An investigation was conducted to study the relationship between cellulolytic, nitrogen-fixing and phosphate-solubilizing microbial counts and age of rehabilitated forest. A random sampling design was used to obtain four replicates of five composite soil of 0–10 cm depth soil samples of 4, 9, 14 and 19-year-old rehabilitated forest. Three selective media: Congo red cellulose, nitrogen-free malate and calcium phosphate media were used for the enumerations of cellulolytic, nitrogen-fixing and phosphate-solubilizing microbes, respectively. Cellulolytic and phosphate-solubilizing microbes were counted based on the formation of clearing zones, while nitrogen-fixing microbes were based on the formation of blue halo on the respective media. There was positive linear relationship between age of the rehabilitated forest and microbial count. These findings revealed that the potentials of cellulolytic, nitrogen-fixing and phosphate-solubilizing microbial populations could be used as biological indicators of forest soil rehabilitation.
The electron-phonon coupling constant of the copper oxide-based high temperature superconductors in the van Hove scenario was calculated using three known models and by employing various acoustic data. Three expressions for the transition temperature from the models were used to calculate the constants. All three models assumed a logarithmic singularity in the density of states near the Fermi surface. The calculated electron-phonon coupling constant ranged from 0.06 to 0.28. The constants increased with the transition temperature indicating a strong correlation between electron-phonon coupling and superconductivity in these materials. These values were smaller than the values estimated for the conventional three-dimensional BCS theory. The results were compared with previous reports on direct measurements of electron-phonon coupling constants in the copper oxide based superconductors.
MeSH terms: Acoustics; Copper; Electric Conductivity; Electrons; Fever; Hot Temperature; Oxides; Temperature; Transition Temperature; Phonons
Solvent flow reactor system was introduced into the extraction system to increase the system efficiency and enhance the extraction yield by adding fresh solvent during the extraction processes. The liquefaction experiment was carried out at various flow-rates (1, 3 and 5 ml/min), reaction times (30, 45 and 60 min) and reaction temperatures (300ºC, 350ºC, 400ºC, 420ºC and 450ºC) with tetralin as solvent. Despite the ability of adding fresh solvent into the extraction process, the conversion of oil+gas was still considered to be low as there was ~25% of coal extracts left to be converted into low molecular weight compounds. One possible option to increase the oil yield is by applying catalyst that will further break up the coal extracts into small molecular weight compounds. In this study, a second reactor was introduced consisting of catalyst (NiSiO2) assuming that the catalyst would interact more effectively with coal extracts rather than the coal itself. In the
absence of catalyst, the oil yield was 55%. By introducing the Ni catalyst, the oil yield increased by 15%. Further analysis of GCMS showed that the oil from catalytic liquefaction gave out more low molecular weight compounds in comparison to the un-catalytic liquefaction oil.
Transition metals play an important role in the growth of carbon nanotubes (CNTs). Series of unsupported hybrid catalysts consisting of Ni:Cu, Ni:Cr, and Ni:Mn doped with Nd catalyst, respectively were synthesized by impregnation method. The catalytic performance of the catalyst for the production of CNTs was measured in the pyrolysis process of hydrocarbon source by catalytic chemical vapour deposition method. Acetylene gas was used as the source of carbon in the pyrolysis process. The decomposition of acetylene was carried out at 700ºC. The bulk properties of the catalysts were investigated by X-ray diffraction. Field emission scanning electron microscopy and thermal analysis were used to observe the morphology and thermal stability of the as-synthesized CNTs, respectively. Hybrid catalyst of Ni:Mn/Nd and Ni:Cr/Nd in 3:1 atomic ratio gave high percentage of carbon yield which was assigned for the high production of CNTs with the mass of yield 18 times greater than the initial mass of the catalyst used.
Staphylococcus kloosii, an orange pigment-producing bacterium, was isolated from the respiratory tree of Holothuria (Mertensiothuria) leucospilota (Brandt 1835) from Teluk Nipah, Pangkor Island, Perak, Malaysia. This report is the first documentation of this Gram-positive strain, referred to as Strain 68 in Malaysia. A partial 16S ribosomal RNA gene sequence of the mesophilic strain has been registered with GenBank (National Center for Biotechnology Information, US National Library of Medicine) with accession number JX102547. Phylogenetic analysis using the neighbour-joining method further supported the identification of Strain 68 as S. kloosii. The circular strain produced orange pigments on tryptone glucose yeast extract agar (TGYEA) and in nutrient broth (NB) at approximately pH 7. The visible spectra of ethanolic and methanolic pigment extracts of the bacterial strain were considered identical with λmax at 426, 447 and 475 nm and λmax at 426, 445 and 473 nm, respectively. Both visible spectra resemble the visible spectra of lutein, which is a commercial carotenoid; however, further analyses are required to confirm the identity of this pigment. The methanolic extracts of the intracellular pigments comprised at least three pigment compounds: an orange pigment compound (major compound), a yellow pigment compound (the least polar) and a pink pigment compound (the most polar). These findings are the first documentation of the pigment composition of S. kloosii as no such record could be found to date.
MeSH terms: Agar; Ethanol; Methanol; Animals; Biotechnology; Carotenoids; Documentation; Food; Glucose; Malaysia; National Library of Medicine (U.S.); Phylogeny; Staphylococcus; United States; Lutein; Genes, rRNA; Databases, Nucleic Acid; Citrus sinensis; Holothuria; Islands
In this study, Centella asiatica and surface soils were collected from 12 sampling sites in Peninsular Malaysia, and the barium (Ba) concentrations were determined. The Ba concentration [µg/g dry weight (dw)] was 63.72 to 382.01 µg/g in soils while in C. asiatica, Ba concentrations ranged from 5.05 to 21.88 µg/g for roots, 3.31 to 11.22 µg/g for leaves and 2.37 to 6.14 µg/g for stems. In C. asiatica, Ba accumulation was found to be the highest in roots followed by leaves and stems. The correlation coefficients (r) of Ba between plants and soils were found to be significantly positively correlated, with the highest correlation being between roots-soils (r=0.922, p
We here describe a videolaryngoscope assisted fibreoptic tracheal intubation in a 17-year-old patient with Hunter Syndrome (Mucopolysaccharidosis Type II) and known difficult intubation who required posterior cervical fusion surgery for cervical canal stenosis. The patient had a history of failed nasal and oral fibreoptic intubation. The use of a videolaryngoscope enabled continuous visualization of the tracheal inlet and allowed a straightforward nasal fibreoptic intubation attempt without complications. This report suggests a viable alternative for the management of a known difficult airway in children with mucopolysaccharidosis.
This randomised single-blinded study was conducted to evaluate if there was any difference between spinal anaesthesia with hyperbaric bupivacaine 0.5% and intrathecal morphine 0.2mg and combined-spinal epidural using hyperbaric bupivacaine 0.5% with epidural infusion of bupivacaine 0.1% plus fentanyl 2.0μg/ml for 24 hours, postoperative analgesia following hip and knee arthroplasty, in terms of pain score and side effects (nausea, vomiting, pruritus and respiratory depression). Eighty patients ASA I or ASA II, aged between 18 to 75 years who underwent knee and hip arthroplasty of approximately 3-4 hours, duration were recruited. They were randomly allocated to one of two groups by using computer generated randomised numbers. The pain score during the postoperative period was evaluated using Visual Analogue Score (VAS pain score) and the side effects were documented and treated accordingly. Results showed that patients in Group 1 and Group 2 were comparable in terms of age, gender, height, weight and race. There was no statistical difference in VAS pain score between the two groups at all times intervals. However, patients in Group 1 had a higher incidence of nausea and pruritus than patients in Group 2. None of the patients in either group, experienced respiratory depression. Thus, it was concluded that both intrathecal morphine 0.2mg and epidural infusion of bupivacaine 0.1% plus fentanyl 2.0μg/ml were comparable in providing postoperative analgesia up to 24 hours following hip and knee arthroplasty. Nevertheless, the use of spinal morphine led to a higher incidence of side effects namely nausea and pruritus.
The tranversus abdominis plane (TAP) block for postoperative analgesia after caesarean section may confer potential benefits comparable to that of intrathecal opioids. We compared postoperative analgesia, and the incidence of nausea, vomiting, pruritus and sedation between the TAP block and intrathecal morphine (ITM) in patients undergoing Caesarean section. This was a prospective, randomised clinical study. Fifty American Society of Anaesthesiologists physical status I or II patients, planned for elective caesarean section under spinal anaesthesia, were randomly allocated to the TAP group (patients receiving spinal anaesthesia with bilateral TAP block without ITM) or ITM group (patients receiving spinal anaesthesia with ITM without a TAP block). Assessment for pain, postoperative nausea and vomiting, pruritus and sedation was done upon arrival and discharge from recovery, and at 6, 12 and 24 hours, postoperatively in the post natal ward. Results were analysed using analysis of variance (ANOVA). There was no pain at rest in either groups. Both groups experienced pain on movement at the 12th (p = 0.6) and 24th hour (p = 0.4). None of the patients in the TAP group experienced nausea, vomiting, pruritus or sedation. However, these incidences were found to be significantly higher in the ITM group. Ultrasound guided TAP block provided comparable postoperative analgesia to ITM without the side effects of the latter.
MeSH terms: Analgesia; Analgesics, Opioid; Analysis of Variance; Anesthesia, Spinal; Cesarean Section; Female; Humans; Morphine; Pain; Pregnancy; Prospective Studies; Pruritus; United States; Incidence; Postoperative Nausea and Vomiting
Ambulatory surgery has now becoming increasingly popular and it is generally well accepted. Major complications following ambulatory surgery are very rare but certain postoperative symptoms can be very unpleasant and distressing to the patients. Follow-up phone calls regarding their well being at home following the surgery may give us the clue and allow us to identify certain problems that can be sorted out immediately or as a reference for a better service in future. The present study was carried out to determine the prevalence of common postoperative symptoms and their subsequent effects within 24 hours after ambulatory surgery by follow-up phone calls. We prospectively studied 199 ASA I and II patients, but only 187 patients were analyzed. Patients had undergone general surgery, orthopaedic, urology, gynaecology or ear, nose and throat (ENT) surgery. Pain was scored based on Numerical Rating Scale (NRS). Majority of patients (70.8%) had only mild pain prior to discharge home. At 24 hours postoperatively, pain was the commonest symptom reported (92.5%) followed by sleepiness (72.2%), dizziness (49.7%), sore throat (17.1%), nausea and vomiting (7.5%) and headache (7%). Sleep was mildly affected in nearly 50% of the patients. Fifty seven percent of patients did not need assistance in performing daily activities during the 24 hours, post surgery. Majority of patients were satisfied (81.3%) with ambulatory surgery. In conclusion, pain was the commonest postoperative symptom encountered following the surgery. Sleep was mildly affected by the postoperative symptoms. Most of the patients did not need assistance in performing their daily activities following surgery. All patients were able to return to at least more than 50% of their normal daily activities at 24 hours after the surgery. Overall satisfaction towards ambulatory surgery was good.
Post-intubation airway related adverse effects such as coughing on the endotracheal tube (ETT), restlessness, hoarseness and sore throat are common and undesirable outcomes of anaesthesia using endotracheal intubation. This prospective randomized single blind study was carried out to compare the effectiveness of intra-cuff dexamethasone and alkalinized lignocaine in reducing the incidence of post-intubation airway related adverse effects. Eighty four patients aged 18 – 60 years, of ASA status I or II, were randomly allocated into three groups: air, dexamethasone and alkalinized lignocaine. Their ETT cuffs were inflated according to the group they were allocated to. The incidence of coughing on the ETT, restlessness, hoarseness and sore throat was assessed, postoperatively. The results showed a significant difference in the incidence of cough, restlessness, hoarseness and sore throat in the dexamethasone group compared to the air group. All the patients had minimal or no sore throat at all documented times. Both intra-cuff dexamethasone and alkalinized lignocaine significantly reduced the incidence of hoarseness. However, alkalinized lignocaine additionally lowered the incidence of restlessness, significantly.
This prospective, randomised study compared the effectiveness of patient controlled epidural analgesia (PCEA) versus continuous epidural infusion (CEI) in providing pain relief post gynaecological surgery. Sixty six ASA I or II patients planned for gynaecological surgery via Pfannensteil incision under combined spinal epidural anaesthesia were recruited. They were randomised into two groups: Group A patients received PCEA while Group B patients received CEI. In the recovery area, both groups received an epidural combination of levobupivacaine 0.1% and fentanyl 2 μg/ml. Group A patients were allowed demand bolus doses of 5 ml with a 20 minute lockout interval, while Group B patients had their epidural infusion initiated at 6 ml/hour with increments as required to a maximum of 12 ml/hour. Pain score and degree of motor blockade was assessed hourly in the first four hours and subsequently at four hourly intervals. Side effects were recorded at four-hourly interval. The total amount of analgesia, number of anaesthetic interventions and patient satisfaction was assessed 24 hours, postoperatively. There was no significant difference in pain score, total amount of analgesia, number of anaesthetic interventions and patient satisfaction. The degree of motor blockade and side effects were comparable between the groups. In conclusion, PCEA was comparable to CEI for pain relief after gynaecological surgery.
Platinum based adjuvant chemotherapy is generally recommended for ovarian cancer to improve the survival rate. Intravenous route is commonly used, easily administered and less associated complications. However, intraperitoneal route is gaining its popularity as a single procedure or adjunctive to the intravenous route. Numerous questions on its eligibility and safety are still perplexed. A case review on a patient with non optimal debulking surgery of advanced ovarian cancer was studied. Intravenous platinum based chemotherapy combined with paclitaxel failed to bring her to clinical remission. Second line chemotherapy, gemcitabin rendered her to poor response with unresolved debilitating ascites needing recurrent drainage. Surprisingly, a trial of intraperitoneal chemotherapy with cisplatin revealed a great response with a complete clinical remission.