Browse publications by year: 2015

  1. Supri, A.G., Siti Hajar, M.D., Jalilah, A.J.
    MyJurnal
    Blends of poly (vinyl chloride) and poly (ethylene oxide) with the addition of carbon black
    as filler was prepared via solution casting technique to fabricate a conductive polymer film. Besides,
    poly (ethylene glycol diglycidyl ether) (PEGDE) was added into the formulation in order to improve its
    properties. The surface morphology of the conductive polymer film was characterized via scanning
    electron microscope (SEM). The results showed that the conductivity of the film was greatly enhanced
    by incorporating the PEGDE as the surface modifier in the PVC/PEO conductive polymer film.
  2. Suriania, M.J., Alib, A., Khalina, A., Sapuan, S. M.
    MyJurnal
    In this study, fatigue failures of bio-composite materials were predicted due to
    manufacturing defects. Kenaf bast fibres were used to fabricate a bio-composite material with epoxy as
    a binding material. The bio-composites were manufactured by using a hand lay-up process. The defects
    in the Kenaf/epoxy bio-composite were determined by a non-destructive technique using Infrared
    thermal imager. Besides, the thermography analyses were verified via optical microscope and scanning
    electron microscope (SEM) investigations. Determinations of fatigue, as well as damage had been
    predicted, and it was found that the damage could be fixed with the predicted results.
  3. Razali, A.A., Sadikin, A.
    MyJurnal
    This paper presents a numerical simulation of flow in a microchannel heat sink. The channel
    was defined as a dimension with less than 1.0milimeter and greater than 100.0micrometer. The ANSYS
    CFX 2015 was used to predict the flow in the microchannel. Besides, simulations were undertaken to
    determine the flow of the fluid within the microchannel in three different models. Therefore, three
    different models were employed for this study. The first model was a square-shaped channel with 0.5mm
    width and 0.5mm height constructed along 28.0mm channel length. The second and the third models
    were in rectangular shape. The differences between these models were their width and height of
    channel. The dimension for the second model was 0.75mm height and 0.5mm width (rectangular A),
    while the dimension for the third model was 0.5mm height and 0.75mm width (rectangular B). All the
    microchannel heat sink models had been simulated and showed results for pressure, temperature, and
    velocity inside the microchannel. The results were compared for each model and the data had been
    validated from published data. In addition, the initial velocity was set in a range between 0.1m/s and
    0.5m/s. The highest pressure drop was recorded for the square microchannel. It was 58.12% higher
    than the pressure drop found in the rectangular microchannel with 0.75mm width, while 0.02% closer
    with the 0.75mm-height rectangular microchannel. Furthermore, there was a 33.34% of temperature
    difference, which had been higher for the square microchannel. Nevertheless, the highest velocity of
    0.57m/s was recorded at the outlet of the microchannel. These had been consistent with other published
    data.
  4. Mat Salleh, N.S., Din, R., Abdul Manaf, S.Z., Hamdan, A., Karim, A.A.
    MyJurnal
    A questionnaire Usability Self Learning Module is developed to measure the overall
    development of the learning module Adobe Photoshop constructs involving three modules, module’s
    usability, applying theory of the cognitive load and minimalist. The study was conducted to produce
    empirical data on the reliability and validity of the Usability of Adobe Photoshop’s Module
    questionnaire using the Rasch Measurement Model. A survey was conducted on 120 participants who
    attended the course Adobe Photoshop using the modules studied. The questionnaire is distributed
    using one of the Web 2.0 technology platform, Google Docs. The reliability and validity of the
    Usability Adobe Photoshop’s module questionnaire were tested with the Rasch Measurement Model
    using the Winstep version 3.69.1.11 program.The Rasch analysis showed that person reliability index
    is 0.87 and item reliability of 0.94. In term of item polarity, each item was able to contribute to
    measuring the effectiveness of the learning module development measurement since the PTMEA
    CORR exceeded 0.30, in specific between 0.50 to 0.78. There are 27 items in the questionnaire, which
    is divided into 3 different constructs. Each construct contains 7 to 11 items. The unidimensionality test
    conducted showed standardized residuals variance of 49.8%, with the biggest secondary dimension
    in the first constrast amounting variance of 6.5%. Item fit analysis showed that none of the items
    needed to be dropped since infit mean square values are between 0.73 and 1.39, and the outfit mean
    square values are between 0.70 and 1.40. Items in the questionnaires are ordered in a continuum of
    increasing intensity for the measurement of the Usability of Module construct. This shows the validity
    of the constructs in Usability of the module.The Rasch Measurement Model shows that the Usability
    of the Module has a high reliability and validity to be used for measuring the usability of the module
    and the application of cognitive load theory and the theory of minimalism
  5. T.R. Ibrahim, Jamil, M.M., Adamu, M.I., Hashim, G. A.
    MyJurnal
    In this paper, Reynolds average Navier stokes models simulation was computed
    with standard k-є, realizable k-є and SST k-w.The three models were proposed to forecast the
    turbulence flow behaviour inside a rectangular channel with two baffle plates. The geometry
    and the grid were generated using commercial CFD software fluent. The flow behaviours of
    three models were characterized based on positions of the entrance to the first baffle,
    positions between first and second baffle and lastly the second baffle. At the three different
    positions the three models studied have demonstrate differences in the velocity profiles and
    separation range. Comparison with previous literatures shows applicability of these three
    models to produce velocity profile characteristics and separation behaviours. Even though
    some of the models have shown slight deviation from the experimental results but in general
    the three models were considered to be in close agreement with most published literatures.
  6. Abdul Manaf, S.Z., Din, R., Hamdan, A., Mat Salleh, N.S., Kamsin, I.F., Abdul Aziz, J.
    MyJurnal
    At present, the learning activities carried out is in line with the rapid growth of development of technology and lifestyle. ICT literacy is categorised as those who can operate a computer and Internet. This study is conducted to determine the level of computer and Internet literacy in generation Y. A total of ten respondents among university students were interviewed. The level of the skill is measured in terms of the use of information processing systems and the Internet. The new knowledge addresses the themes in information communication technology literacy namely; defining, accessing, assessing, managing, integrating, creating and passing data. As such, the model of computer technology in education can also be produced. A more robust method of learning can be heightened by seeing the level of skills possessed by university students. The findings of this study is expected to determine the level of competence of the students and university can provide the necessary equipment to ensure effective teaching and learning.
    MeSH terms: Literacy; Computers; Life Style; Surveys and Questionnaires; Software; Students; Universities; Problem-Based Learning; Internet
  7. Fatimah, A.R.H., Supri, A.G., Firuz, Z.
    MyJurnal
    In this study, compatibilizing effects of caprolactam-maleic anhydride (CL-MAH) and
    polyethylene-grafted-maleic anhydride (PE-g-MAH) with different blend compositions on polymer
    blends of recycled high density polyethylene (RHDPE) and ethylene vinyl acetate (EVA) blends were
    investigated by tensile properties and swelling behavior. The use of CL-MAH improved the
    compatibility of RHDPE80/EVA20 blend composition, and tensile properties of the resultant blend
    compared well with those of RHDPE/EVA blends. Addition of PE-g-MAH improved the tensile
    properties of RHDPE/EVA/PE-g-MAH blends than RHDPE/EVA blends without compatibilizer. The
    scanning electron microscopy (SEM) morphologies of fracture surface for RHDPE/EVA blends with
    presence of compatibilizers showing better incorporation of two different phases of polymer matrix.
    MeSH terms: Caprolactam; Ethylenes; Maleic Anhydrides; Microscopy, Electron, Scanning; Polymers; Vinyl Compounds; Polyethylene
  8. Jualang Azlan, G. I., Marziah, M.
    MyJurnal
    This study was conducted to establish callus cultures from leaf, stem and root explants of
    Physalis minima using different combinations of 2,4-D and kinetin. Callus growth and anti-cancer
    compound, physalin B production were further enhanced by optimising the cell explants and media
    compositions such as basal media, salts concentration, carbon sources and plant growth regulators.
    The results indicated that callus cultures derived from leaf, stem and root explants were best initiated
    using a combination of 9.0 µM 2,4-D and 4.5 µM kinetin. Callus growth and synthesis of physalin B
    were peaked at the late exponential growth phase over 25 d of culture. Callus growth did not vary
    between explants, but physalin B was observed higher in leaf (0.78 mg g-1 dry wt.), followed by root
    (0.71 mg g-1 dry wt.) and stem (0.64 mg g-1 dry wt.). MS basal medium was found superior to B5, SH
    and WH basal media in supporting growth and physalin B production. Further tests on the media
    compositions obtained a half strength of MS salts (½MS), 2.5% (w/v) sucrose and 9.0:4.5 µM of 2,4-
    D:kinetin combination, which were the preferred salts strength, carbon sources and plant growth
    regulators for optimum growth (0.23 g dry wt.) and physalin B production (1.75 mg g-1 dry wt.) of
    callus cultures derived from leaf.
  9. Radwan, H., Khalil, M., Annuar, F., Azmi, H., Zakaria, M. Z.
    MyJurnal
    Palm oil-based wax is a waste material from palm oil refining process. Recent prototyping
    activities have used industrial blue wax or synthetic wax to produce prototype parts by machining
    processes. The new palm oil-based wax blended with LLDPE reduces the use of synthetic wax for
    engineering applications. This paper studies the machining characteristic of two different composite
    blends: LLDPE/PALMAC 95 -16 Palm Oil-Based Wax and LLDPE/PALMAC 98-18 Palm Oil-Based
    Wax. Three machining characteristic results were recorded, namely; surface roughness, temperature
    and dimensional consistency.
  10. Rajaee, N., Hussaini, A. A. S. A, Zulkharnain, A., Masra, S. M. W
    MyJurnal
    In this paper, we propose an approach to model and simulate a network problem using
    bio-inspired computing. Information in a network is embedded in DNA sequence strands and in-vitro
    implementation is proposed via bio-molecular tools such as hybridization, ligation and polymerase
    chain reaction. The output of the computation is derived from gel electrophoresis process.
  11. Mohd Yunus, N. Z., Wei, N. T., Yung, Y. C., Marto, A., Pakir, F., Hezmi, M. A., et al.
    MyJurnal
    Besides traditional chemical stabilizers, polymer emulsion that is considered as a nontraditional
    chemical stabilizer had been introduced recently. Among polymer emulsions, Canlite and
    Probase have been widely used for soil stabilization. The aim of this paper is to investigate the
    effectiveness of Laterite soil stabilization treated by Canlite-liquid and Probase-liquid soil stabilizers.
    A testing program, scheduled to achieve the overall objectives of this study was conducted to
    determine the basic properties of Laterite soil, establish the relationship between the compaction
    characteristics (maximum dry density and optimum moisture content) with the amount of polymer
    emulsion and last but not least to compare the strength of the Canlite-treated and Probase-treated
    Laterite soil. The effects of both polymer soil stabilizers – Canlite and Probase – were examined. The
    optimum moisture content of the mixtures was used as a reference to determine the water content for
    the preparation of all the specimens and later used in the unconfined compressive strength (UCS) test.
    The laboratory test results showed that the additional amount of Canlite and Probase have improved
    the physical properties, liquid limit and unconfined compressive strength (UCS) of the Laterite soil.
    The compressive strength of the treated Laterite was found varied and depends on the type of
    stabilizers, quantity of additives and curing time. From the UCS tests, it was found that Probase
    improves the strength of the Laterite more than Canlite.
  12. Abdullah, K. F., Bahak, M. Z.
    MyJurnal
    here are many contaminants that could lead to the alteration of oil viscosity. Diesel fuel
    is one of the deteriorating contaminants for diesel engine oils. It is among the main factors that give
    high impact towards the deterioration of engine oils as one study has found that, in average, 0.36% of
    total fuel consumption ends up in the crankcase. Many studies have demonstrated the effect of fuel
    dilution on the wear characteristic. However, there are limited studies that focused on the percentage
    amount affecting the wear characteristics together with other influencing factors such as load, speed
    and temperature. In this research, used motor oil - Gibson 20W50 had been mixed well with fuel
    percentages of 0, 1, 3, 5 and 7, hence creating 5 samples that were run under different speeds. The
    experiment is conducted by following the ASTM 4172 standard. Based on the results, the fuel
    contamination in used motor oil was considered limiting at 5% contamination and became totally
    deteriorated at 7%. Through a Stribeck Curve, it could be understood that wear is inversely
    proportional to sliding velocity, where it is one of the lubrication parameters together with speed and
    load. Rough surface on the balls indicated that abrasive wear has occurred due to the use of used
    motor oil
  13. Ali, E. N., Jamaludin , M. Z.
    MyJurnal
    Moringa oleifera is a plant with various benefits to mankind from its root until leaves.
    From food to biofuel applications, all parts are useful for daily uses. In this research, the pod husk
    was examined to determine the possibility of producing ethanol. The pod husks were dried and used in
    two forms; one is grinded into powder, and the other is cut within 5 x 5 x 2 mm. About 10 grams of
    Moringa oleifera pod husk was put into a conical flask and added with distilled water up to 250 mL.
    The pre-treatment was made by adding an alkaline solution, NaOH, where the pH of the sample was
    adjusted to (4.5, 5.0, and 5.5) using H2SO4. The samples were autoclaved at a temperature of 120°C
    for 2 hours before the samples were cooled to room temperature (25+/-2oC). Baker’s yeast
    (Saccharomyces cerevisiae) was prepared with different concentrations (1g, 5g, and 10g) and added
    to the samples for fermentation process that took place in the incubator shaker at a temperature of
    36°C, for a period of 72 hours. The bioethanol concentration was measured using High Performance
    Liquid Chromatography (HPLC) with a refractive index detector and REZEX ROA-Organic Acid
    HPLC Column using 0.05 N H2SO4 as the mobile phase. The bioethanol produced from Moringa
    oleifera pod husk was 8.400 g/L using 1g/L yeast, and the fermentation took place at pH 4.5 for the
    sample size of 5 x 5 x 2 mm. The results showed that Moringa oleifera pod husk can be introduced as
    a new material for bioethanol production in Malaysia and other tropical countries where this tree is
    available
  14. Jehad, D. G., Hashim, G. A., Zarzoor, A. K., Nor Azwadi, C. S.
    MyJurnal
    Numerical studies are conducted on turbulent incompressible flow over 2D backwardfacing
    step in order to investigate the performance of three different turbulence models (standard k-e,
    realizable k-e and SST k-ω) in predicting the region of separation and reattachment behind the edge
    of the step. Current solutions of Reynolds number (Re= 13200) and expansion ratio (H: H2=1:3) are
    compared with experimental measurements. Among the turbulence models, SST k-ω and standard k-e exhibited good agreement with the experimental results.
  15. Azmi, H., Sanuddin, A. B., Zakimi, M. Z., Jamali, M. S., Radhwan, H., Khalilf , A. N. M., et al.
    MyJurnal
    A coconut de-husking machine comprising of two rollers with spikes, chain drives,
    presser, clearers, shafts and belting system was developed for small-scale production in rural areas.
    Performance test analysis showed that the machine de-husks coconut fruits without any nut breakage
    or distortion of the extracted fibre length. The objective of this project is to improve the efficiency and
    productivity in producing coconut fruits without husks by using the best selection of mechanical
    mechanisms with minimum costs. One electric motor (2hp, 1500rpm) is used to drive two shafts using
    a combination of pulley and belt. In between the motor and the shafts, one box of worm gears is used
    to reduce the rotation speed from 1500rpm to 21rpm (ratio 70:1). Two metal cylinders with a series of
    spikes are used to remove the husks from the coconut fruit and are attached to the rotary shaft. The
    machine’s average de-husking efficiency and capacity are 90.42% and 222 coconuts per hour,
    respectively. In addition, the development of the machine is also a solution to the constraint of space,
    whereby a compact-size machine is more suitable for small and medium enterprises (SME’s). Plus, it
    operates with lesser noise, which also contributes to a more viable operating condition for the
    environment.
  16. Muhamad, I. I., Md Katan, N. S., Shaharuddin, S., Abang Zaideld, D. N.
    MyJurnal
    The present study reports on the preparation processes and characterization of fibers from pineapple cores. The effects of different washing techniques (tap-water and hot-water washing) and particle sizes (0.2, 0.5 and 1 mm) on two important characteristics of dietary fiber, i.e. water holding capacity (WHC) and oil holding capacity (OHC), were investigated. It was found that the washing pre-treatment significantly improved WHC. Meanwhile larger particle sizes of fiber gave better WHC and OHC for all types of fibers. Tap-water washing was the most appropriate pretreatment method compared to hot-water washing and unwashed method. However, there was no difference in morphologies of the fibers before and after being prewashed at different particle sizes. The fiber morphology was preserved best after the drying process using microwave freeze dryer (MFD) and microwave vacuum dryer (MVD). This study demonstrates the potential of pre-treatment and drying methods in functional fiber preparation for food enrichment.
  17. Kuan Mei Yang, Rusli Ahmad, Siti Mariam Abdullah
    MyJurnal
    This is a study on employees’ perception of justice towards performance-based pay and
    the effect of these perceptions on their turnover intention. This study aims to examine
    the mediating role played by distributive and procedural justice in linking pay distribution
    and pay procedure of performance-based pay to employees’ turnover intention. A
    review of past literature in this particular area has prompted the researchers to narrow
    the gaps in previous studies. Towards that, this study utilized questionnaires which
    were administered among 50 non-managerial employees currently working in a private
    company located in Kuching, Sarawak, East Malaysia. Data analysis was done using
    Statistical Package for Social Sciences (SPSS), Version 20.0. Pearson Correlation and
    Stepwise Regression were used to examine the relationship between the variables. The
    outcomes of Stepwise Regression revealed that distributive justice fully mediated the
    relationship between pay distribution and employees’ turnover intention in contrast to
    procedural justice which did not have a significant impact in the relationship. The findings
    of this study are useful references for organisation management of the pay system
    to improve employees’ performance.
    MeSH terms: Malaysia; Perception; Personnel Turnover; Surveys and Questionnaires; Research Personnel; Social Justice; Social Sciences; Intention
  18. Dhillon KS
    Malays Orthop J, 2015 Mar;9(1):47-52.
    PMID: 28435599 DOI: 10.5704/MOJ.1503.008
    We are all aware that there has been a dramatic increase in the number of anterior cruciate ligament (ACL) reconstructions that are carried out here in Malaysia as well as around the world. The numbers of ACL injuries have undoubtedly increased over the years with greater participation of young adults in sporting activities. However it is not certain whether the increase in the numbers of reconstructions can be accounted for by the increasing numbers of ACL injuries. Without doubt commercial interests as well the influence of the biomedical companies have a role to play. In the past the rational for surgical treatment of an ACL tear was that the ACL is vital for knee function and that in the long term ACL deficiency will lead to more injuries of the meniscus and more degeneration of the joint. This belief was prevalent because the natural history of an ACL deficient knee was not known although the ultimate outcome of reconstruction of the ACL was not known either. However in past few years a substantial amount research has been published, which has elucidated the natural history of ACL deficient knees as well as the long term outcome of reconstruction of the ACL.
    MeSH terms: Humans; Joint Instability; Knee Joint; Malaysia; Anterior Cruciate Ligament; Young Adult; Anterior Cruciate Ligament Reconstruction; Anterior Cruciate Ligament Injuries; Meniscus
  19. Chiew YS, Pretty CG, Shaw GM, Chiew YW, Lambermont B, Desaive T, et al.
    PMID: 28435689 DOI: 10.1186/s40814-015-0006-2
    BACKGROUND: Selecting positive end-expiratory pressure (PEEP) during mechanical ventilation is important, as it can influence disease progression and outcome of acute respiratory distress syndrome (ARDS) patients. However, there are no well-established methods for optimizing PEEP selection due to the heterogeneity of ARDS. This research investigates the viability of titrating PEEP to minimum elastance for mechanically ventilated ARDS patients.

    METHODS: Ten mechanically ventilated ARDS patients from the Christchurch Hospital Intensive Care Unit were included in this study. Each patient underwent a stepwise PEEP recruitment manoeuvre. Airway pressure and flow data were recorded using a pneumotachometer. Patient-specific respiratory elastance (Ers ) and dynamic functional residual capacity (dFRC) at each PEEP level were calculated and compared. Optimal PEEP for each patient was identified by finding the minima of the PEEP-Ers profile.

    RESULTS: Median Ers and dFRC over all patients and PEEP values were 32.2 cmH2O/l [interquartile range (IQR) 25.0-45.9] and 0.42 l [IQR 0.11-0.87]. These wide ranges reflect patient heterogeneity and variable response to PEEP. The level of PEEP associated with minimum Ers corresponds to a high change of functional residual capacity, representing the balance between recruitment and minimizing the risk of overdistension.

    CONCLUSIONS: Monitoring patient-specific Ers can provide clinical insight to patient-specific condition and response to PEEP settings. The level of PEEP associated with minimum-Ers can be identified for each patient using a stepwise PEEP recruitment manoeuvre. This 'minimum elastance PEEP' may represent a patient-specific optimal setting during mechanical ventilation.

    TRIAL REGISTRATION: Australian New Zealand Clinical Trials Registry: ACTRN12611001179921.

  20. Ng LC, Helen, Razak IA, Ghani WMN, Marhazlinda J, Rahman ZAA, Norlida A, et al.
    Ann Dent, 2015;22(1):2-5.
    MyJurnal
    This study aims to identify the relationship between dietary intakes of β-carotene with risk of oral cancer.
    Methods: A hospital-based, case-control study was conducted on 306 Malaysians who seek treatment at participating centres/hospitals. Subjects selected from the Malaysian Oral Cancer Data and Tissue Banking System (MOCDTBS) consisted of 153 cases and 153 controls that were matched for gender, age (±5 years) and ethnicity. Food consumption was measured using Food Frequency Questionnaire (FFQ). NutrieMart Version 2.0.0 software was used to estimate daily nutrient of each subject from the FFQ. Logistic Regression analysis was conducted to compute the odds ratio (OR) for intakes of β-carotene and oral cancer risk.
    Results: Intake of β-carotene was found to be not associated with risk of oral cancer (OR 0.83, 95%CI: 0.42-1.66, p>0.05).
    Conclusion: No significant association was found between dietary intakes of β-carotene with oral cancer risk in this study population.
    MeSH terms: Adult; Hospitals; Humans; Malaysia; Mouth Neoplasms*; Logistic Models; Case-Control Studies; beta Carotene*
External Links