A high concentration of phosphorus in wastewater may lead to excessive algae growth and deoxygenation of the water. In this work, nanofiltration (NF) of phosphorus-rich solutions is studied in order to investigate its potential in removing and recycling phosphorus. Wastewater samples from a pulp and paper plant were first analyzed. Commercial membranes (DK5, MPF34, NF90, NF270, NF200) were characterized and tested in permeability and phosphorus removal experiments. NF90 membranes offer the highest rejection of phosphorus; a rejection of more than 70% phosphorus was achieved for a feed containing 2.5 g/L of phosphorus at a pH <2. Additionally, NF90, NF200 and NF270 membranes show higher permeability than DK5 and MPF34 membranes. The separation performance of NF90 is slightly affected by phosphorus concentration and pressure, which may be due to concentration polarization and fouling. By adjusting the pH to 2 or adding sulfuric acid, the separation performance of NF90 was improved in removing phosphorus. However, the presence of acetic acid significantly impairs the rejection of phosphorus.
Hermetia illucens larvae by nature are a decomposer which fed on organic wastes. This study explores the potential of producing biodiesel using lipids from H. illucens larvae. Three types of organic wastes (sewage sludge, fruit waste and palm decanter cake from oil palm mill) were selected based on considerable generation and disposal concern in the area of study as well as lack of investigations as feed for Hermetia illucens larvae in current literatures. Growth rate of the larvae was determined with studying the changes in the biomass per day. H. illucens larvae fed with fruit waste and palm decanter cake have shown growth rates of 0.52±0.02 and 0.23±0.09 g d(-1), respectively. No positive sign of growth were observed in the larvae fed with treated sewage sludge (-0.04±0.01 g d(-1)). Biodiesel as fatty acid methyl ester (FAME) was synthesized by transesterification of the larvae lipid using sulphuric acid as catalyst in methanol. FAME produced was ascertained using ATR-FTIR spectroscopy and GC-MS. The main compositions of fatty acid were found to be C12:0, C16:0 and C18:1n9c. Fatty acid composition of C12:0 fed with fruit waste, sewage sludge and palm decanter was found to be most abundant in the larvae lipid. The amount of C12:0 obtained was 76.13%, 58.31% and 48.06%, respectively. In addition, fatty acid of C16:0 was attained at 16.48% and 25.48% fed with sewage sludge and palm decanter, respectively. Based on the findings, FAME derived from larvae lipids is feasible to be used for biodiesel production.
As methyltheobromine (MTB) has been increasingly detected in wastewater, it would be necessary to develop more intensive and effective approaches to remove MTB. As Co species immobilized on carbonaceous materials appears as a promising catalyst, doping carbon with nitrogen has been also validated to significantly enhance catalytic activities for Oxone activation. Therefore, it is desired to develop a composite of immobilizing Co species on N-doped carbonaceous supports for activating Oxone to degrade MTB. Unfortunately, very few studies have demonstrated such composites for activating Oxone to degrade MTB as this type of composites are conventionally prepared via complex procedures. Alternatively, this study aims to develop such a composite conveniently by using a cobaltic coordination polymer (CP) as a precursor. Specifically Co2+ and 4,4-bipyridine (BIPY) are selected for formulating a special one-dimensional CP, which is then carbonized to convert Co to Co nanoparticles (NPs) and transform BIPY to carbon nitride (CN) matrices. Because of 1-D coordinated structure of CoBIPY, the resulting magnetic Co NPs are well-distributed and protected within CN to form a magnetic Co-embedded carbon nitride composite (MCoCN). In comparison to pristine CN and Co3O4, MCoCN exhibits much higher catalytic activities to activate Oxone for degrading MTB completely within 7 min. MCoCN also shows a much lower activation energy of 24.6 kJ/mol than other reported catalysts for activating Oxone to degrade MTB. The findings of this study validate that the 1-D coordination polymer of CoBIPY is a useful precursor to prepare MCoCN for effectively activating Oxone to degrade MTB.
Since 5-sulfosalicylic acid (SFA) has been increasingly released to the environment, SO4--based oxidation processes using Oxone have been considered as useful methods to eliminate SFA. As Co3O4 has been a promising material for OX activation, the four 3D Co3O4 catalysts with distinct morphologies, including Co3O4-C (with cubes), Co3O4-P (with plates), Co3O4-N (with needles) and Co3O4-F (with floral structures), are fabricated for activating OX to degrade SFA. In particular, Co3O4-F not only exhibits the highest surface area but also possesses the abundant Co2+ and more reactive surface, making Co3O4-F the most advantageous 3D Co3O4 catalyst for OX activation to degrade SFA. The mechanism of SFA by this 3D Co3O4/OX is also investigated and the corresponding SFA degradation pathway has been elucidated. The catalytic activities of Co3O4 catalysts can be correlated to physical and chemical properties which were associated with particular morphologies to provide insights into design of 3D Co3O4-based catalysts for OX-based technology to degrade emerging contaminants, such as SFA.
The efficacy of Virkon S, a commercial disinfectant as a virucidal spray against human enterovirus 71 (HEV71), the causative agent of the fatal form of hand, foot and mouth disease was examined. At least one log10 reduction of HEV71 titer was achieved when one spray of Virkon (1% or 2%) with ten minutes of contact time was applied. The infectivity was completely lost when four sprays of 1% or 2% Virkon were applied, suggesting that at least four sprays of 1% Virkon to the surface bound HEV71 was necessary to completely inactivate the virus. These findings suggest that Virkon S at the proper concentration is suitable to be used as an effective and easy to use disinfectant against HEV71.
Carbon dots have great potential to be utilised as an optical sensing probe due to its unique photoluminescence and less toxic properties. This work reports a simple and novel synthesis method of carbon dots via direct acid hydrolysis of bovine serum albumin protein in a one-pot approach. Optimisation of the important synthetic parameters has been performed which consists of temperature effect, acid to protein ratio and kinetics of reaction. Higher temperature has promoted better yield with shorter reaction time. The carbon dots obtained shows a strong emission at the wavelength of 400 nm with an optimum excitation of 305 nm. The potential of the carbon dots as optical sensing probe has been investigated on with different cations that are of environmental and health concern. The fluorescence of the carbon dots was significantly quenched particularly by lead (II) ions in a selective manner. Further analytical study has been performed to leverage the performance of the carbon dots for lead (II) ions sensing using the standard Stern-Volmer relationship. The sensing probe has a dynamic linear range up to 6.0 mM with a Stern-Volmer constant of 605.99 M(-1) and a limit of detection (LOD) of 5.05 μM. The probe performance was highly repeatable with a standard deviation below 3.0%. The probe suggested in this study demonstrates the potential of a more economical and greener approach that uses protein based carbon dots for sensing of heavy metal ions.
An optical sensor for Hg(II) monitoring using a complex of zinc dithizonate immobilised on XAD 7 which is based on reflectance spectrophotometry has been developed in this study. Measurements were made using a kinetic approach whereby the reflectance signal is measured at a fixed time of 5 min. The sensor could be regenerated using a saturated solution of KCl in 1 M sulphuric acid. The sensor was found to have an optimum response at pH 3.0 with respective measurement repeatability and probe-to-probe reproducibility of 1.53% and 5.26%. A linear response was observed in the Hg(II) concentration range of 0.0-180.0 ppm with a calculated limit of detection (LOD) of 0.05 ppm. The results obtained for aqueous Hg(II) determination using this probe were found to be comparable with the well-established method of atomic absorption spectrometry.
A simple atomic-absorption spectrophotometry method is described for the determination of silver, bismuth, cadmium, copper, iron, nickel and zinc in lead- and tin-base solders and white-metal bearing alloys, with use of a single sample solution. The sample is dissolved in a mixture of hydrobromic acid and bromine, then fumed with sulphuric acid. The lead sulphate is dissolved in concentrated hydrochloric acid. The method is particularly suitable for the determination of silver and bismuth, which are co-precipitated with lead sulphate. The other elements can also be determined after removal of the lead sulphate by filtration.
The purpose of this study is to determine the concentration of the selected elemental composition in a multi-storey hostel. Dust samples were taken from three random rooms at each level of the student hostel by sweeping the floor. The concentrations of elements (Cd, Cu, Fe, Pb and Zn) were determined by using Inductively Coupled Plasma-Optical Emission Spectrometer (ICPOES) after digestion with nitric acid and sulfuric acid solutions. Dust samples analysis has shown the different levels of sampling point does not affect the concentration of the elements. The concentration of elements in investigated microenvironment was in the order of Fe > Zn > Cu > Pb > Cd. The correlation analysis was applied to elements variable in order to identify the sources of an airborne contaminant. It was discovered the strong positive correlation between Cu-Zn which indicates the sources come from traffic emission and street dust. This result was supported by the Principal Component Analysis (PCA) that revealed the presence of elements in the student hostel originated from the outdoor sources.
A novel powdering material that utilizes acid-modified Imperata cylindrica (IC) powder for the development of fingermarks was studied. Experiments were carried out to determine the suitability, adherence quality and sensitivity of the acid-modified IC powder. Fingermarks of different constituents (eccrine, sebaceous and natural fingermarks) on different types of surfaces were used. Acid-modified IC powder was also used to develop fingermarks of different ages as well as aged fingermarks recovered from the water. From the visual inspection, acid-modified IC powder was able to interact with different fingermark constituents and produced distinct ridge details on the examined surfaces. It was also able to develop aged fingermarks and fingermarks that were submerged in water. A statistical comparison was made against the Sirchie® Hi-Fi black powder in terms of the powders' sensitivity and quality of the developed natural fingermarks. The image quality was analyzed using MITRE's Image Quality of Fingerprint (IQF) software. From the experiments, acid-modified IC powder has the potential as a fingermark development powder, although natural fingermarks developed by Sirchie® black powder showed better quality and sensitivity based on the results of the statistical comparison.
Biodegradable polymeric films, obtained from chitosan/natural rubber latex (CS/NRL) blends with different compositions, have been prepared by wetting process. The blends were characterized by dynamic mechanical thermal analysis (DMTA) and found that the CS/NRL blends are thermodynamically incompatible. This is evident from the presence of two glass transitions, corresponding to CS and NRL phases in the blend. The mechanical properties of the CS/NRL blends were improved with increasing the amount of chitosan and after surface treatment with sulphuric acid due to the sulfonate ionic interaction. The dielectric properties was determined using Precision LCR meter in the frequency range 75 kHz up to 30 MHz. After CS/NRL surface treatment with sulphuric acid at high content of chitosan showed the highest dielectric constant. The surface properties of the CS/NRL blend films before and after surface treatment were confirmed by atomic force microscopy (AFM), respectively.
Poly(hydroxamic acid) ion exchange resin was evaluated for speciation of iron(II) and iron(III) ions. Distribution coefficients indicate that the resin is more selective towards iron(III) ion. Column extractions show that iron(III) ion is quantatively extracted from sulfuric acid solutions at concentrations of between 0.01 to 0.00lM but only 2% or less of iron(II) ion is retained under these conditions. Further studies show that these two ions can be separated and their separations are not affected by the presence of nickel, zinc, copper, calcium, chloride, bromide, nitrate and sulphate.
Resin penukar ion poli(asid hidroksamik) telah dikaji untuk penspesiesan ion-ionferum. Pekali taburan menunjukkan resin ini mempunyai kepilihan yang tinggi terhadap ion ferik berbanding dengan ionferus. Pengekstrakan dengan kaedah turus mendapati ion ferik dari larutan asid sulfurik 0.01 dan 0.00lM boleh diesktrak secara kuantitatif manakala pengekstrakan ion ferus hanya 2% atau lebih kecil. Kajian lanjut menunjukkan resin ini boleh memisahkan ion ferik dari ion ferus dan pemisahan ini tidak diganggu oleh kehadiran ion-ion nikel, zink, kuprum, kalsium, klorida, bromida, nitrat dan sulfat.
The liquefaction of oil palm empty fruit bunch (EFB) in phenol was carried out in the presence of sulfuric acid as a catalyst in the reflux condenser system. The effect of initial phenol input and EFB on liquefaction reaction was investigated by measuring the reaction yield, EFB residue and combined phenol. The initial ratio of phenol to EFB has the greatest influence on the residue and reaction yield. The liquefaction products consist of some liquid by products with high amount of OH groups. The amount of this byproduct is 0.5 time of the solid product (phenolic resin).
In this study, cellulose nanocrystals (CNC) were produced using acid hydrolysis method. Kenaf core was pretreated with 4
wt. % sodium hydroxide (NaOH), followed by bleaching using 1.7 wt. % sodium chlorite (NaClO2
) in acetate buffer. The
bleached fiber was acid hydrolyzed for 45 and 55 min using 64 wt. % sulfuric acid (H2
SO4
). The size distribution of the
CNC segregated via differential centrifugation with different speed was also investigated. The CNC suspension obtained
was centrifuged at 3000, 6000, 9000 and 12000 rpm. The resultant CNC suspension collected was characterized using
Fourier transform infrared (FTIR) analysis, X-ray diffraction (XRD) and transmission electron microscopy (TEM). FTIR
results showed the progressive removal of non-cellulosic constituents for each subsequent treatment. It also showed that
the CNC produced after hydrolysing for 55 min has the highest degree of crystallinity (81.15%). CNC produced from acid
hydrolysis process of 45 min have lengths between 50 and 270 nm while CNC produced from acid hydrolysis process of
55 min have length around 40 to 370 nm.
Different type of fibers which is EFB and KC were liquefied in phenol with the presence of sulphuric acid as a catalyst. The liquefied residue was characterized by using Fourier transform infrared (FTIR) to determine the functional groups presents in both residues, X-ray diffraction (XRD) to determine the degree of crystallinity in the residue, thermogravimetric analysis (TGA) to analyze the thermal properties of the residue and scanning electron microscope (SEM) to investigate the structure and morphology of the residue. Phenol-to-EFB/KC ratio shows great effect on the amount of residue in the liquefaction process. Peak appearance can be observed in the FTIR analysis at 810 and 750 cm-1 which is attributed to the para and meta benzene, respectively or to be specific its associated to the p-alkyl phenol and m-alkyl phenol. In the XRD analysis, CrI of lignocellulosic materials increased after liquefaction process. Liquefaction process caused chemical penetration across the grain of the fiber, thus the fiber bundles started to separate into individual fibers shown in the SEM micrograph and the weights lost curve for both liquefied EFB and KC experienced three region decompositions.
Biofiber is used in the polymer based composite as a renewable resource due to its positive environmental benefits, biodegradable properties, low cost and high toughness. Biocomposite was fabricated using oil palm empty fruit bunch (EFB) as filler in phenolated EFB (PEFB) matrix. Phenolated EFB (PEFB) obtained from liquefaction of EFB in phenol was used as a biopolymer to replace novolak phenolic resin which is commonly used in composite materials. Sulfuric acid was used as a catalyst in the liquefaction reaction. The effect of thermal aging and blending ratio of PEFB matrix and EFB fibers on the mechanical properties of composites has been studied. The flexural data before and after thermal aging revealed the optimum amount of EFB filler is 50% . The result showed better compatibility between EFB and PEFB when compared with EFB and commercial novolak resin.
Pacifier nipples are in permanent contact with saliva and with the oral microflora therefore, act as a favoured site for the growth of biofilms. This research was conducted to identify the bacterial biofilms that has been found on the pacifiers that collected from local child nursery and to analyse the formation of biofilms by Cronobacter sp. during growth in infant formula milk. Pacifiers collected were analysed to obtain colony forming unit (CFU) and isolated bacteria were identified using several biochemical tests according to Bergey's Manual. Biofilm assay of three Cronobacter sp. were conducted using 24 wells microtiter plate and stained with 1% of crystal violet solution at different time interval: 6, 12, 18 and 24 h. The hydrophobicity of the bacterial cell suspension was evaluated using bacterial adhesion to hydrocarbons (BATH) method. Extracellular polymeric substances (EPS) analysis was done to identify percentage of carbohydrate and protein content by using phenol sulphuric acid method and Bradford method, respectively. The results obtained showed that the normal microflora bacteria were the most abundant microorganisms that were found on the pacifier with the main genus isolated was Staphylococcus sp., Enterobacteriaceae sp. and Clostridium sp. Based on biofilm and EPS analysis, Cronobacter sakazakii formed a strong biofilms after 18 h, with carbohydrate was identified as main component of EPS.
Levulinic acid (LA) is one of biomass derived building block chemicals with various applications. Catalytic esterification
of LA with alkyl alcohol produces levulinate ester which can be applied as fragrance, flavouring agents, as well as fuel
additives. In this study, a series of sulfated silica (SiO2
) catalyst was prepared by modification of SiO2
with sulfuric acid
(H2
SO4
) at different concentrations; 0.5 M to 5 M H2
SO4
. The catalysts were characterized, and tested for esterification
of LA with ethanol to ethyl levulinate (EL). The effect of various reaction parameters including reaction time, catalyst
loading and molar ratio of LA to ethanol on esterification of LA to EL were inspected. The catalyst with high concentration
of acid sites seemed suitable for LA esterification to EL. Among the sulfated SiO2
catalysts tested (0.5 M-SiO2
, 1 M-SiO2
,
3 M-SiO2
and 5 M-SiO2
), 3 M-SiO2
exhibited the highest performance with the optimum EL yield of 54% for reaction
conducted at reflux temperature for 4 h, 30% 3 M-SiO2
loading and LA to ethanol molar ratio of 1:20. Besides, the
reusability of 3 M-SiO2
catalyst for LA esterification with ethanol was examined for five cycles. Esterification of LA with
methanol and 1-butanol were also carried out for methyl levulinate (ML) and butyl levulinate (BL) productions with 69%
and 40% of ML and BL yields, respectively. This study demonstrates the potential of sulfated SiO2
catalyst for levulinate
ester production from LA at mild process condition.
Oil palm empty fruit bunch (EFB) fibres were pretreated by gamma irradiation followed by sodium carbonate (Na2
CO3
)
before the acid hydrolysis process to produce reducing sugars using diluted sulphuric acid (H2
SO4
). In this study, EFB
fibres were irradiated at different doses, i.e. 0, 100 and 200 kGy. Meanwhile, the gamma irradiated sample were then
subjected to Na2
CO3 pretreatment with 0 and 5% total titratable alkali (TTA). The effect of the pretreatment using gamma
irradiation and Na2
CO3
on the physical and chemical properties of the EFB fibres and the yield of the reducing sugar
obtained from the acid hydrolysis process was investigated. The obtained results showed that the content of holocellulose
was increased significantly with the increase of irradiation doses combined with Na2
CO3 pretreatment, whereas lignin
content of the EFB was decreased. The gamma irradiation and Na2
CO3 pretreatment resulted in structure breakage
and removal of silica of EFB fibres which can be due to the swelling of the fibres. A synergistic effect between gamma
irradiation and Na2
CO3 was observed, in which the yield of reducing sugars was increased by combining the gamma
irradiation and Na2
CO3 pretreatment.
The aim was to explore the utilization of tea leaf waste fibers (TLWF) as a source for the production of cellulose nanocrystals (CNC). TLWF was first treated with alkaline, followed by bleaching before being hydrolyzed with concentrated sulfuric acid. The materials attained after each step of chemical treatments were characterized and their chemical compositions were studied. The structure analysis was examined by Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD). From FTIR analysis, two peaks at 1716 and 1207 cm-1-which represent C=O stretching and C⁻O stretching, respectively-disappeared in the spectra after the alkaline and bleaching treatments indicated that hemicellulose and lignin were almost entirely discarded from the fiber. The surface morphology of TLWF before and after chemical treatments was investigated by scanning electron microscopy (SEM) while the dimension of CNC was determined by transmission electron microscopy (TEM). The extraction of CNC increased the surface roughness and the crystallinity index of fiber from 41.5% to 83.1%. Morphological characterization from TEM revealed the appearance of needle-like shaped CNCs with average diameter of 7.97 nm. The promising results from all the analyses justify TLWF as a principal source of natural materials which can produce CNC.