As the world's second largest palm oil producer and exporter, Malaysia could capitalize on its oil palm biomass waste for power generation. The emission factors from this renewable energy source are far lower than that of fossil fuels. This study applies an integrated carbon accounting and mitigation (INCAM) model to calculate the amount of CO2 emissions from two biomass thermal power plants. The CO2 emissions released from biomass plants utilizing empty fruit bunch (EFB) and palm oil mill effluent (POME), as alternative fuels for powering steam and gas turbines, were determined using the INCAM model. Each section emitting CO2 in the power plant, known as the carbon accounting center (CAC), was measured for its carbon profile (CP) and carbon index (CI). The carbon performance indicator (CPI) included electricity, fuel and water consumption, solid waste and waste-water generation. The carbon emission index (CEI) and carbon emission profile (CEP), based on the total monthly carbon production, were determined across the CPI. Various innovative strategies resulted in a 20%-90% reduction of CO2 emissions. The implementation of reduction strategies significantly reduced the CO2 emission levels. Based on the model, utilization of EFB and POME in the facilities could significantly reduce the CO2 emissions and increase the potential for waste to energy initiatives.
An appropriate technology for waste utilisation, especially for a large amount of abundant pressed-shredded oil palm empty fruit bunch (OFEFB), is important for the oil palm industry. Self-sustained pyrolysis, whereby oil palm biomass was combusted by itself to provide the heat for pyrolysis without an electrical heater, is more preferable owing to its simplicity, ease of operation and low energy requirement. In this study, biochar production under self-sustained pyrolysis of oil palm biomass in the form of oil palm empty fruit bunch was tested in a 3-t large-scale pool-type reactor. During the pyrolysis process, the biomass was loaded layer by layer when the smoke appeared on the top, to minimise the entrance of oxygen. This method had significantly increased the yield of biochar. In our previous report, we have tested on a 30-kg pilot-scale capacity under self-sustained pyrolysis and found that the higher heating value (HHV) obtained was 22.6-24.7 MJ kg(-1) with a 23.5%-25.0% yield. In this scaled-up study, a 3-t large-scale procedure produced HHV of 22.0-24.3 MJ kg(-1) with a 30%-34% yield based on a wet-weight basis. The maximum self-sustained pyrolysis temperature for the large-scale procedure can reach between 600 °C and 700 °C. We concluded that large-scale biochar production under self-sustained pyrolysis was successfully conducted owing to the comparable biochar produced, compared with medium-scale and other studies with an electrical heating element, making it an appropriate technology for waste utilisation, particularly for the oil palm industry.
The availability of paddy husk from rice processing plants remains high owing to increase in the worldwide rice consumption. Increasing demand for chicken products leads to poultry wastes production. Co-composting of the aforementioned wastes could solve the indiscriminate disposal of these wastes. Thus, co-composting of paddy husk and chicken slurry with clinoptilolite zeolite and urea as additive was carried out. Clinoptilolite zeolite was used to enhance ammonium and nitrate retention in the compost. Temperature of the compost was monitored three times daily for 55 days. Cation exchange capacity, organic matter, ash, humic acids, pH, total C, N, C/N ratio; total P, exchangeable Ca, Mg, K, NH4+, NO3-, and heavy metals contents were determined using standard procedures. pH, total N, humic acids, ash, NH4+, NO3-, P, Ca, Mg, and K contents increased but the salinity, heavy metals contents, and microbial population were low after the co-composting process. Zea mays L. (test crop) seed germination rate in distilled water and the compost were not significantly different. Growth of Spinach oleracea (test crop) on a peat-based growing medium and the compost was also not significantly different. These findings were possible because the clinoptilolite zeolite used in co-composting reduced accumulation of heavy metals that may have damage effects on the test crops. Mature compost with good agronomic properties can be produced by co-composting chicken slurry and paddy husk using clinoptilolite zeolite and urea as additives.
Lignocellulosic biomass has been widely recognised as a potential low-cost source for the production of high added value materials and proved to be a good precursor for the production of activated carbons. One of such valuable biomasses used for the production of activated carbons is palm shell. Palm shell (endocarp) is an abundant by-product produced from the palm oil industries throughout tropical countries. Palm shell activated carbon and palm shell carbon molecular sieve has been widely applied in various environmental pollution control technologies, mainly owing to its high adsorption performance, well-developed porosity and low cost, leading to potential applications in gas-phase separation using adsorption processes. This mini-review represents a comprehensive overview of the palm shell activated carbon and palm shell carbon molecular sieve preparation method, physicochemical properties and feasibility of palm shell activated carbon and palm shell carbon molecular sieve in gas separation processes. Some of the limitations are outlined and suggestions for future improvements are pointed out.
A one-step self-sustained carbonization of coconut shell biomass, carried out in a brick reactor at a relatively low temperature of 300-500°C, successfully produced a biochar-derived adsorbent with 308 m2/g surface area, 2 nm pore diameter, and 0.15 cm3/g total pore volume. The coconut shell biochar qualifies as a nano-adsorbent, supported by scanning electron microscope images, which showed well-developed nano-pores on the surface of the biochar structure, even though there was no separate activation process. This is the first report whereby coconut shell can be converted to biochar-derived nano-adsorbent at a low carbonization temperature, without the need of the activation process. This is superior to previous reports on biochar produced from oil palm empty fruit bunch.
Biomass is considered as the largest renewable energy source in the world. However, some of its inherent properties such as hygroscopicity, lower energy content, low mass density and bio-degradation on storage hinder its extensive application in energy generation processes. Torrefaction, a thermochemical process carried out at 200-300°C in a non-oxidative environment, can address these inherent problems of the biomass. In this work, torrefaction of bagasse was performed in a bench-scale tubular reactor at 250°C and 275°C with residence times of 30, 60 and 90 mins. The effects of torrefaction conditions on the elemental composition, mass yield, energy yield, oxygen/carbon (O/C) and hydrogen/carbon (H/C) ratios, higher heating values and structural composition were investigated and compared with the commercially available 'Thar 6' and 'Tunnel C' coal. Based on the targeted mass and energy yields of 80% and 90% respectively, the optimal process conditions turned out to be 250°C and 30 mins. Torrefaction of the bagasse conducted at 275°C and 90 min raised the carbon content in bagasse to 58.14% and resulted in a high heating value of 23.84 MJ/kg. The structural and thermal analysis of the torrefied bagasse indicates that the moisture, non-structural carbohydrates and hemicellulose were reduced, which induced the hydrophobicity in the bagasse and enhanced its energy value. These findings showed that torrefaction can be a sustainable pre-treatment process to improve the fuel and structural properties of biomass as a feedstock for energy generation processes.
This study demonstrated the effect of two-pot sequential pretreatment, comprising of ultrasound assisted deep eutectic solvent (DES) with the aim to investigate the effects of ultrasound amplitude and duration in enhancing delignification. Oil palm fronds (OPF) were ultrasonicated in a water medium, followed by a pretreatment using DES (choline chloride:urea). Fourier transform infra-red spectroscopy, X-ray diffraction, field emission scanning electron microscope, Brunauer-Emmet-Teller and solubilised lignin concentration were conducted to confirm the effectiveness of ultrasound assisted DES on the pretreatment of OPF. The recommended ultrasound conditions were determined to be 70% amplitude and duration of 30 min, where the sequential DES pretreatment was able to reduce lignin content of OPF to 14.01%, while improving xylose recovery by 58%.
5-Hydroxymethylfurfural (HMF) has been identified as a promising biomass-derived platform chemical. In this study, one pot production of HMF was studied in ionic liquid (IL) under probe sonication technique. Compared with the conventional heating technique, the use of probe ultrasonic irradiation reduced the reaction time from hours to minutes. Glucose, cellulose and local bamboo, treated with ultrasonic, produced HMF in the yields of 43%, 31% and 13% respectively, within less than 10min. The influence of various parameters such as acoustic power, reaction time, catalysts and glucose loading were studied. About 40% HMF yield at glucose conversion above 90% could be obtained with 2% of catalyst in 3min. Negligible amount of soluble by-product was detected, and humin formation could be controlled by adjusting the different process parameters. Upon extraction of HMF, the mixture of ionic liquid and catalyst could be reused and exhibited no significant reduction of HMF yield over five successive runs. The purity of regenerated [C4C1im]Cl and HMF was confirmed by NMR spectroscopy, indicating neither changes in the chemical structure nor presence of any major contaminants during the conversion under ultrasonic treatment. 13C NMR suggests that [C4C1im]Cl/CrCl3 catalyses mutarotation of α-glucopyranose to β-glucopyranose leading to isomerization and finally conversion to HMF. The experimental results demonstrate that the use of probe sonication technique for conversion to HMF provides a positive process benefit.
Feather keratin is a biomass generated in excess from various livestock industries. With appropriate processing, it holds potential as a green source for degradable biopolymer that could potentially replace current fossil fuel based materials. Several processing methods have been developed, but the use of ultrasonication has not been explored. In this study, we focus on (i) comparing and optimizing the dissolution process of turkey feather keratin through sonication and conventional processes, and (ii) generating a biodegradable polymer material, as a value added product, from the dissolved keratin that could be used in packaging and other applications. Sonication of feather keratin in pure ionic liquids (ILs) and a mixture containing ILs and different co-solvents was conducted under different applied acoustic power levels. It was found that ultrasonic irradiation significantly improved the rate of dissolution of feather keratin as compared to the conventional method, from about 2 h to less than 20 min. The amount of ILs needed was also reduced by introducing a suitable co-solvent. The keratin was then regenerated, analyzed and characterized using various methods. This material holds the potential to be reused in various appliances.
Highly stable and dispersible nanocrystalline cellulose (NCC) was successfully isolated from oil palm empty fruit bunch microcrystalline cellulose (OPEFB-MCC), with yields of 93% via a sono-assisted TEMPO-oxidation and a subsequent sonication process. The sono-assisted treatment has a remarkable effect, resulting in an increase of more than 100% in the carboxylate content and a significant increase of approximately 39% in yield compared with the non-assisted process. TEM images reveal the OPEFB-NCC to have rod-like crystalline morphology with an average length and width of 122 and 6nm, respectively. FTIR and solid-state 13C-NMR analyses suggest that oxidation of cellulose chain hydroxyl groups occurs at C6. XRD analysis shows that OPEFB-NCC consists primarily of a crystalline cellulose I structure. Both XRD and 13C-NMR indicate that the OPEFB-NCC has a lower crystallinity than the OPEFB-MCC starting material. Thermogravimetric analysis illustrates that OPEFB-NCC is less thermally stable than OPEFB-MCC but has a char content of 46% compared with 7% for the latter, which signifies that the carboxylate functionality acts as a flame retardant.
In this study, a simple sugaring-out supported by liquid biphasic flotation technique combined with ultrasonication was introduced for the extraction of proteins from microalgae. Sugaring-out as a phase separation method is novel and has been used in the extraction of metal ions, biomolecules and drugs. But, its functioning in protein separation from microalgae is still unknown. In this work, the feasibility of sugaring-out coupled with ultrasound for the extraction of protein was investigated. Primary studies were carried out to examine the effect of sonication on the microalgae cell as well as the separation efficiency of the integrated method. Effect of various operating parameters such as the concentration of microalgae biomass, the location of sonication probe, sonication time, ultrasonic pulse mode (includes varying ON and OFF duration of sonication), concentration of glucose, types of sugar, concentration of acetonitrile and the flow rate in the flotation system for achieving a higher separation efficiency and yield of protein were assessed. Besides, a large-scale study of the integration method was conducted to verify the consistency of the followed technique. A maximum efficiency (86.38%) and yield (93.33%) were attained at the following optimized conditions: 0.6% biomass concentration, 200 g/L of glucose concentration, 100% acetonitrile concentration with 5 min of 5 s ON/10 s OFF pulse mode and at a flow rate of 100 cc/min. The results obtained for large scale were 85.25% and 92.24% for efficiency and yield respectively. The proposed liquid biphasic flotation assisted with ultrasound for protein separation employing sugaring-out demonstrates a high production and separation efficiency and is a cost-effective solution. More importantly, this method provides the possibility of extending its application for the extraction of other important biomolecules.
Durian peel, an abundant waste in Malaysia could be a potential substrate for fermentable sugar recovery for value-added biochemical production. Common pretreatment such as acid or alkaline pretreatment resulted in the need for extensive solid washing which generated wastewater. Herein, this study aims to introduce sonication on top of chemical pretreatment to destruct lignin and reduce the chemical usage during the durian peel pretreatment process. In this study, the morphology and the chemical composition of the pretreated durian peels were studied. The sugar yield produced from the chemical pretreatment and the combined ultrasound and chemical pretreatment were compared. The morphology and chemical structure of durian peels were investigated by Scanning Electron Microscope (SEM), Fourier Transform Infrared (FTIR) analysis and X-ray diffraction (XRD). The SEM images showed that the structural change became more significant when sonication was introduced. Second, XRD profile indicated a relatively higher crystallinity index and FTIR spectra displayed a lower intensity of lignin and hemicellulose for ultrasound plus alkaline (UB) pretreatment as compared to acid, alkaline and ultrasound plus acid (UA) pretreatment. UB and UA pretreatment portrayed higher yield (376.60 ± 12.14 and 237.38 ± 3.96 mg reducing sugar/g dry biomass, respectively) than their controls without the application of ultrasound. Therefore, it could be concluded that ultrasound was able to intensify the fermentable sugar recovery from durian peel by inducing physical and chemical effect of cavitation to alter the morphology of durian peel. Fermentation of UB treated durian peel resulted in 2.68 mol hydrogen/mol consumed sugar and 131.56 mL/Lmedium/h of hydrogen productivity. This study is important because it will shed light on a way to handle durian waste disposal problems and generate fermentable sugars for the production of high value-added products.
Hand weeding continues to be one of the most laborious aspects of nursery
maintenance. Oxygenated monoterpene, an important group of secondary metabolite found in
essential oils, has a potential herbicidal activity that could be exploited as natural herbicide
whereas organic mulch could delay weed emergence. Thus, this study aimed to examine the
phytotoxicity of geraniol, an oxygenated monoterpene compound, in combination with
lemongrass leaf mulch against three common weeds, Eleusine indica (grass), Cyperus distans
(sedge), and Tridax procumbens (broadleaf). Greenhouse experiments were carried out by
treating 4.0 t/ha lemongrass leaf mulch with 7.5% (v/v) geraniol compound. The pretreated
mulch acted synergistically and inhibited the emergence and shoot growth of T. procumbens
completely. However, the pretreated mulch exhibited a moderate inhibitory effect on C. distans
emergence and growth. Geraniol-treated lemongrass leaf mulch acted synergistically and
inhibited the emergence of E. indica by 72%, but it acted antagonistically and caused a 45%
reduction of shoot biomass. The present findings suggest that geraniol-treated lemongrass leaf
mulch has potent herbicidal activity but its phytotoxic effect is species-dependent.
This study focused on feasibility analysis of hybrid electrification system for an aqua-tourism resort located remotely from the grid connection in Terengganu. There were four standalone systems used in this study: diesel/PV/biomass/battery, diesel/PV/battery, biomass/diesel/battery, and diesel only. The design and analysis of these systems were done using Hybrid Optimization of MultipleEnergy Resources (HOMER) software. The results showed that the diesel/PV/battery system was the optimum solution in terms of net present cost (NPC) and cost of energy (COE). This system comprises 20 % of PV penetration with NPC and COE of USD 57,823 (RM 241, 729.90) and 0.428 USD/kWh (1.79 RM/kWh), respectively. Meanwhile, the diesel/PV/biomass/battery system with NPC of USD 65,388 (RM 273, 355.49) and COE of 0.484 USD/kWh (2.02 RM/kWh) was found to be the best among all systems in terms of greenhouse emissions. This system was able to reduce almost 70 % of carbon dioxide if compared with diesel only system and about 15 % lower than the diesel/PV/battery system with a renewable energy fraction of 44 %.
Tropical peat swamp forest (PSF) is a unique wetland ecosystem with distinct vegetation types. Due to the waterlogged environment, the stand characteristics in this ecosystem are different from those of other inland forests. This paper highlights stand characteristics of a PSF based on our investigation of a 1 ha ecological plot established in a Virgin Jungle Reserve (VJR) at Compartment 100, Pekan Forest Reserve, Pahang, Malaysia. This site is considered a Gonystylus bancanus-rich area. From the inventory, we recorded a total of 49 tree species from 38 genera and 25 families among all trees of ≥ 10 cm in diameter at breast height. Calophyllum ferrugineum var. ferrugineum was the most abundant species, followed by G. bancanus. The forest appeared healthy, as all tree characteristics (crown shape, log grade and climber infestation) generally fell within Classes 1 and 2 (good and moderate categories), with the exception of crown illumination which majority of the trees were rated as class 3 (received less sunlight). The latter finding indicates that most of the trees living under the canopy received minimal illumination. In terms of total tree biomass, we estimated that about 414.6 tonnes exist in this 1 ha area; this tree biomass is higher than in some PSF areas of Sumatra, Indonesia.
To investigate the distribution of Anacardiaceae in Teluk Bahang Permanent Forest Reserve (TBPFR) in Pulau Pinang, all trees with a diameter at breast high (DBH) ≥ 5 cm were enumerated in a study site constituting 0.4 ha of the reserve. Seventy five individuals of Anacardiaceae (14% of all trees) are recorded. These individuals represent 4 genera and 5 species, namely, Mangifera pentandra, Mangifera macrocarpa, Gluta elegans, Campnosperma auriculatum and Swintonia floribunda. The mean density of Anacardiaceae within the study plots is 7.50±8.14 (mean±S.D.) per ha whereas the basal area (BA) calculated is 0.97 m(2)/0.40 ha. The importance value (IVi) for Anacardiaceae is 81%. The estimated total aboveground biomass (TAGB) for Anacardiaceae is 24.24 ton/0.40 ha. A total of 333 Anacardiaceae saplings with a DBH < 5 cm are recorded. These saplings have been identified as juveniles of the genera Gluta (9.99%), Swintonia (84.90%) and Mangifera (5.11%).
Rattans (subfamily Calamoideae) are an important component of the forests of the Old World. However, few studies have been conducted on the distribution of these abundant palms within different habitats, specifically in Peninsular Malaysia. This study was aimed at assessing rattan diversity, abundance and biomass change across two different habitat types, namely, dipterocarp forests and fresh-water swamps within the Segari Melintang Forest Reserve, Perak, within two years. All rattan stems within five 100 m × 100 m sized study plots (A-E) of the two habitat types were counted in 2011 and 2013, and Shannon-Wiener diversity indices (H') and Bray-Curtis dissimilarity indices were calculated. A total of 11 species from 5 genera (161 stems ha(-1)) were sampled. Rattan abundance was higher in all swamp plots; however, rattan diversity (H') was highest in the dipterocarp plot (D: H' (2011)1.79; H' (2013)1.84). Bray-Curtis indices of rattan abundance (highest similarity in swamp: plot BC(2011) 0.484, BC(2013) 0.262) and biomass were highest for study plots with the same vegetation types in both years. For rattan biomass, the most similar plot pairs changed during the years: dipterocarp plots A and D were most similar in 2011 (0.509), and swamp plots B and C were most similar in 2013 (0.282). This study helped contribute information regarding the distribution and dynamics of rattans in a primary rainforest of Peninsular Malaysia.
Mangroves support diverse macroalgal assemblages as epibionts on their roots and tree trunks. These algae provide nutrients to the primary consumers in the aquatic food web and have been reported to be substantial contributors to marine ecosystems. The species diversity, biomass, and habitat characteristics of mangrove macroalgae were investigated at three stations in the Sibuti mangrove estuary, Sarawak, Malaysia, from November 2012 to October 2013. Three groups of macroalgae were recorded and were found to be growing on mangrove prop roots, namely Rhodophyta (Caloglossa ogasawaraensis, Caloglossa adhaerens, Caloglossa stipitata, Bostrychia anomala, and Hypnea sp.), Chlorophyta (Chaetomorpha minima and Chaetomorpha sp.), and Phaeophyta (Dictyota sp.). The biomass of macroalgae was not influenced (p>0.05) by the season in this mangrove forest habitat. The macroalgal species Hypnea sp. contributed the highest biomass at both Station 1 (210.56 mg/cm(2)) and Station 2 (141.72 mg/cm(2)), while the highest biomass was contributed by B. anomala (185.89 mg/cm(2)) at Station 3. This study shows that the species distribution and assemblages of mangrove macroalgae were influenced by environmental parameters such as water nutrients, dissolved solids, and salinity in the estuarine mangrove habitats of Sibuti, Sarawak.
Mycorrhiza, a mutualistic association between fungi and higher plants, has been documented extensively, but much less is known about the development of arbuscular mycorrhizal (AM) fungi and their effects on the growth of peanuts (Arachis hypogea L.). Therefore, the mycorrhizal status of Glomus spp. was investigated in the following diverse substrate soil conditions: non-autoclaved soil, autoclaved soil and autoclaved soil plus soil microbiota. The results indicated that both the arbuscular mycorrhizae, Glomus mosseae (Nicol. & Gerd.) Gerd. & Trappe, and Glomus fasciculatum (Thaxter) Gerd. & Trappe emend. Walker & Koske were infective to peanut, but displayed a differential impact on peanut growth depending on the microbial biomass content of the substrate soils. G. mosseae proved to be the most effective at improving peanut growth.
Basal stem rot (BSR) is a devastating disease to Malaysian oil palm. Current techniques employed for BSR disease detection on oil palm are laborious, time consuming, costly, and subjected to accuracy limitations. An ergosterol detection method was developed, whereby it correlated well with the degree of infection in oil palm. This current study was designed to study the relationship between Ganoderma biomass, ergosterol concentration, BSR disease progress and to validate the efficiency of microwave assisted extraction (MAE) method for extraction of ergosterol compound. In addition, testing on the sensitivity of thin layer chromatography (TLC) analysis for detection of ergosterol was also the aim of this study. The optimised procedure involved extracting a small amount of Ganoderma-infected oil palm root tissues suspended in low volumes of solvent followed by irradiation in a conventional microwave oven at 70°C and medium high power for 30 s, resulting in simultaneous extraction and saponification. Based on the results obtained, MAE method may be effective in extracting low to high yields of ergosterol from infected oil palm roots demonstrating disease scale 2, 3 and 4. Positive relationship was observed between ergosterol content and inoculation period starting day 3 in the inoculated oil palm seedlings and hour 6 in germinated seeds. TLC analysis demonstrated a good correlation with high performance liquid chromatography (HPLC) quantification. Therefore, a semi-quantitative TLC analysis may be applied for handling a large amount of samples during onset field survey.