Phlebotomine sand flies were collected using CO2 baited CDC light trap in 2000 and 2001 in limestone areas and caves of western Malaysia. A total of 1,548 specimens were collected comprising 18 species from two genera: Phlebotomus (6 spp) and Sergentomyia (12 spp). Phlebotomus major major (38.9%) was the predominant species followed by Sergentomyia perturbans (20.1%), P. stantoni (15.3%) and others. Biting activity of the sand flies at the Gua Senyum caves, Gua Kota Gelanggi, Batu caves and Gua Kelam were observed using the bare leg landing catch (BLC) technique. Four Phlebotomus spp at Gua Senyum were found to bite humans with a unimodal biting peak (between 01:00 and 04:00 AM). At Gua Kota Gelanggi P. major major was observed to bite humans, but at Batu Caves and Gua Kelam no sand flies were observed to bite humans. Sergentomyia spp did not feed on humans even though high numbers were caught in light traps. The populations of phleobotomine sand flies fluctuated, with several peaks especially among P. major major which peaked in December and was low in February and August. Phlebotomus stantoni was abundant throughout 2001. Most species populations were weakly related to rainfall because they inhabited caves.
The growths of the African catfish (Clarias gariepinus) and water spinach (Ipomoea aquatica) were evaluated in recirculation aquaponic system (RAS). Fish production performance, plant growth and nutrient removal were measured and their dependence on hydraulic loading rate (HLR) was assessed. Fish production did not differ significantly between hydraulic loading rates. In contrast to the fish production, the water spinach yield was significantly higher in the lower hydraulic loading rate. Fish production, plant growth and percentage nutrient removal were highest at hydraulic loading rate of 1.28 m/day. The ratio of fish to plant production has been calculated to balance nutrient generation from fish with nutrient removal by plants and the optimum ratio was 15-42 gram of fish feed/m(2) of plant growing area. Each unit in RAS was evaluated in terms of oxygen demand. Using specified feeding regime, mass balance equations were applied to quantify the waste discharges from rearing tanks and treatment units. The waste discharged was found to be strongly dependent on hydraulic loading rate.
The efficacy of the larvicidal and pupicidal agent (Agnique) MMF was evaluated against larvae of An. arabiensis and Culex (Diptera: Culicidae) under field conditions in Bahary Locality, Khartoum, Sudan. At an applied dosage of 0.25 ml/m2, MMF resulted in 89.4, 79.8 and 88.2% reductions in L3-L4 instars An. arabiensis and 63.5% in Culex larvae (all stages) 24 to 72 hours post-treatment. Pupae were completely eliminated (100%) within 24 hours posttreatment. The earlier instars (L1-L2) of An. arabiensis were more tolerant with a 62.5% reduction at 72 hours post-treatment compared to (L3-L4) instars and pupae. At 7-days post-treatment Agnique gave a 57.5% reduction in L1-L2 and 92.6% in L3-L4 instar larvae of An. arabiensis and 57.3% and 86.4% in Culex larvae and pupae, respectively. We conclude that Agnique can perform effectively against L3-L4 instars and pupae of An. arabiensis for only 1 week, and 3 to 4 days against L1-L2 instars of Culex spp.
Human amniotic membrane that has been processed and sterilised by gamma irradiation is widely used as a biological dressing in surgical applications. The morphological structure of human amniotic membrane was studied under scanning electron microscopy (SEM) to assess effects of gamma radiation on human amniotic membrane following different preservation methods. The amniotic membrane was preserved by either air drying or submerged in glycerol before gamma irradiated at 15, 25 and 35 kGy. Fresh human amniotic membrane, neither preserved nor irradiated was used as the control. The surface morphology of glycerol preserved amnion was found comparable to the fresh amniotic membrane. The cells of the glycerol preserved was beautifully arranged, homogonous in size and tended to round up. The cell structure in the air dried preserved amnion seemed to be flattened and dehydrated. The effects of dehydration on intercellular channels and the microvilli on the cell surface were clearly seen at higher magnifications (10,000×). SEM revealed that the changes of the cell morphology of the glycerol preserved amnion were visible at 35 kGy while the air dried already changed at 25 kGy. Glycerol preservation method is recommended for human amniotic membrane as the cell morphological structure is maintained and radiation doses lower than 25 kGy for sterilization did not affect the appearance of the preserved amnion.
In this study, hybrid montmorillonite/cellulose nanowhiskers (MMT/CNW) reinforced polylactic acid (PLA) nanocomposites were produced through solution casting. The CNW filler was first isolated from microcrystalline cellulose by chemical swelling technique. The partial replacement of MMT with CNW in order to produce PLA/MMT/CNW hybrid nanocomposites was performed at 5 parts per hundred parts of polymer (phr) fillers content, based on highest tensile strength values as reported in our previous study. MMT were partially replaced with various amounts of CNW (1, 2, 3, 4 and 5phr). The tensile, thermal, morphological and biodegradability properties of PLA hybrid nanocomposites were investigated. The highest tensile strength of hybrid nanocomposites was obtained with the combination of 4phr MMT and 1phr CNW. Interestingly, the ductility of hybrid nanocomposites increased significantly by 79% at this formulation. The Young's modulus increased linearly with increasing CNW content. Thermogravimetric analysis illustrated that the partial replacement of MMT with CNW filler enhanced the thermal stability of the PLA. This is due to the relatively good dispersion of fillers in the hybrid nanocomposites samples as revealed by transmission electron microscopy. Interestingly, partial replacements of MMT with CNW improved the biodegradability of hybrid nanocomposites compared to PLA/MMT and neat PLA.
Twelve species of Anopheles were collected by using cow-baited net trap in a malarial endemic village in northern Peninsular Malaysia. Anopheles maculatus which is the main malaria vector with its densities were related to drought. An. aconitus, An. kochi and An. philippinensis were less susceptible to P. falciparum and P. vivax infection, and are not considered important in falciparum or vivax malaria transmission. Biting activities of An. kochi and An. vagus were primarily active after dusk and steadily declined after midnight. An. maculatus and An. aconitus showed biting activities throughout the night but An. maculatus showed two peaks of biting activity in the first half of the night.
Blood from most of the residents of a remote village in northern peninsular Malaysia, bordering Thailand, was examined for malaria parasites monthly for 1 year. Plasmodium vivax was the commonest infection, but P. falciparum and mixed infections also occurred. Monthly collections of the malaria vector, Anopheles maculatus showed a positive correlation between mosquito densities and malaria positivity in the human population and a negative correlation with rainfall.
Mating behavior between Aedes aegypti and Ae. albopictus, established colony strains were examined under laboratory conditions (30-cm(3) screened cages) for 5 consecutive days. The effect of selected male densities (30, 20, 10) and female density (20) on the number of swarming, mating pairs, eggs produced, and inseminated females were evaluated. Male densities significantly increased swarming behavior, mating pairs, and egg production of heterospecific females, but female insemination was reduced. Aedes aegypti males mate more readily with heterospecific females than do Ae. albopictus males. The current study suggests that Ae. aegypti males were not species-specific in mating, and if released into the field as practiced in genetically modified mosquito techniques, they may mate with both Ae. aegypti and Ae. albopictus females, hence reducing populations of both species by producing infertile eggs.
Polymer blends is a well-established and suitable method to produced new polymeric materials as compared to synthesis of a new polymer. The combination of two different types of polymers will produce a new and unique material, which has the attribute of both polymers. The aim of this work is to analyze mechanical and morphological properties of bio-phenolic/epoxy polymer blends to find the best formulation for future study. Bio-phenolic/epoxy polymer blends were fabricated using the hand lay-up method at different loading of bio-phenolic (5 wt%, 10 wt%, 15 wt%, 20 wt%, and 25 wt%) in the epoxy matrix whereas neat bio-phenolic and epoxy samples were also fabricated for comparison. Results indicated that mechanical properties were improved for bio-phenolic/epoxy polymer blends compared to neat epoxy and phenolic. In addition, there is no sign of phase separation in polymer blends. The highest tensile, flexural, and impact strength was shown by P-20(biophenolic-20 wt% and Epoxy-80 wt%) whereas P-25 (biophenolic-25 wt% and Epoxy-75 wt%) has the highest tensile and flexural modulus. Based on the finding, it is concluded that P-20 shows better overall mechanical properties among the polymer blends. Based on this finding, the bio-phenolic/epoxy blend with 20 wt% will be used for further study on flax-reinforced bio-phenolic/epoxy polymer blends.
Anatomical variations in the femoral vein are of great clinical importance especially in cases of deep vein thrombosis (DVT). Knowledge of the variable anatomy of the femoral vein is important to minimise false-negative findings on ultrasound examination in patients with DVT and help to explain the 'silent' DVT. Furthermore, the presence of a duplicated femoral vein itself is associated with higher incidence of DVT. These venous anomalies are usually due to the truncular venous malformation. In the present study, while dissecting the right lower limb, we found a case of variation of the femoral vein. In this case, besides a duplicated femoral vein, we also noticed a 3rd interconnecting channel near the apex of the femoral triangle joining the two veins. This variation has not been reported previously by other authors. Considering its uniqueness and clinical importance, we decided to report this case.
A burned human remain was found outdoor (5º 27' N, 100º 16' E) in Penang Island. The deceased was last seen alive on 23 April 2010 at 2230 h and was found burned on 24 April 2010 at 1920 h. Larval aggregation of second instar Chrysomya megacephala was observed on the chest of the deceased.
The life history of the male and female of the indoor forensic fly, Synthesiomyia nudiseta was studied under fluctuating temperature of indoor environments and analysed based on the age-stage and two sex life table. The life cycle of S. nudiseta was 14.0±1.0 days from the egg stage to adult emergence. The population parameters calculated were; net reproduction rate (R(o)= 108.6), mean generation time (T(o)= 12.2), intrinsic rate of increase (r(m)= 0.38), and finite rate of increase (λ= 1.46). The pre-oviposition period (APOP) was 6.0± 0.1 days. All population parameters suggested that S. nudiseta exhibits the r-strategist characteristics.
Japanese encephalitis (JE) virus activity is an important cause of viral encephalitis in Southeast Asia. In Malaysia, JEV activity has been first detected in Culex gelidus in 1976. Since then, no study has fully addressed the seasonal dynamics of this mosquito. As irrigated rice production expands, the incidence of JEV vectors, particularly Cx. gelidus is expected to increase. We surveyed Penang Island to determine the breeding patterns of Cx. gelidus and their potential insect predators, in relation to habitat/niche and rice growing period. Six rice fields proper (RFP) and related drainage canals (DC) were visited through three cultivation cycles (CCs) over 17 months. Weekly visits were performed to each of the 36 sites and mosquito larvae and aquatic insects were sampled from RFP and DCs using dippers. Culex gelidus was abundant in RFP and almost absent in DCs. Its densities usually were high during the first and 3rd CC and when the RFs were in Fp, Pp and Gp. In DCs, the mosquito was abundant during Mp, e.g., 2nd CC. Predators, especially those belonging to the families Corixidae, Coenagrionidae and Dytiscidae, were more present in RFP. Predator numbers usually were high during the first CC; in some cases predator abundance peaked during other CCs, e.g., corixids and dysticids. In RFP, neither corixids nor coenagrionids showed any positive correlation with densities of Cx. gelidus. However, dytiscids' population peaked when the mosquito densities were on the rise. These observations suggest that Cx. gelidus is active during the period of rice cultivation. Operational vector control through bio-control or with insecticides near the end of the rice cultivation season in RFP may prove beneficial in reducing the density of Cx. gelidus, but also the amount of bio-agent or insecticide applied on riceland.
The pupae of Desmometopa sp. (Diptera: Milichiidae) were collected from a human corpse found indoor in active decay stage together with the larvae of Sarcophagidae, Synthesiomyia nudiseta (Wulp), Chrysomya megacephala (Fabricius) and Chrysomya rufifacies (Macquart). This research note is the first report of the Desmometopa sp. recovered from a human corpse in Malaysia.
A human corpse at an advanced stage of decomposition was found in a house in the residential area of Bukit Mertajam, Penang, Malaysia. Entomological specimens were collected during the post-mortem and the live specimens were subsequently reared at room temperature. The time of death was estimated to have been 14 days previous to the discovery of the body based on the police investigation. Both adult and larvae of the beetle Dermestes ater (De Geer) were found to be infesting the corpse and from the stage of decomposition of the body and the estimated time of death it would appear that infestation may have begun at a relatively early stage of decomposition.
Larvae of the Synthesiomyia nudiseta (Wulp) were collected from a decomposed human corpse at the Department of Forensic Medicine, Penang Hospital. A colony of this species was established and the eggs were collected for rearing. The developmental times, rearing temperatures, and relative humidity were recorded twice daily from the time the eggs collected until adult emergence. An average of 5 larvae were randomly collected from the rearings twice daily, warm-water killed and preserved in Kahle's solution. The larval instar stages were determined by observing the number of posterior spiracular slits and the length of the preserved larvae were measured. When the larval life cycle was completed, the accumulated developmental times were calculated. A total of 8 replicates were carried out. The temperature of the rearing room was 28.5+/-1.5 degrees Celcius while the relative humidity was within 67-85%. The total developmental time for S. nudiseta was 322+/-19 hours (13.4+/-0.8 days).
A semi laboratory experiment using 3 cohorts of Aedes albopictus adults was performed to obtain age-specific mortality and fecundity information and to derive statistical estimates of some population growth parameters. Life expectancy was calculated for both males and females. The following population parameters were estimated: intrinsic rate of increase (rm= 0.21), net reproductive (replacement) rate (Ro= 68.70), age at mean cohort reproduction (To=10.55 days), birth rate (B=0.23), death rate (D=0.02) and generation time (G=20.14 days). The high rm/B (0.91) and B/D (11.50) ratios indicated the high colonizing ability of Ae. albopictus in nature.
A field study on foraging activity and proteinacous food preference was performed on the tropical fire ant (Solenopsis geminata) (Fabricius) at the School of Biological Sciences and Desasiswa Bakti Permai, Universiti Sains Malaysia (USM), Penang. Foraging activity studies of 4 colonies of S. geminata were conducted in the field for 24 hours. Foraging activity significantly increased 4 hours before sunset and maximum foraging occurred at midnight until early morning. Three types of proteinacous food; anchovy, meat and egg yolk were tested among the five colonies of S. geminata in the field. The egg yolk was the most preferred food (100%) followed by meat (31%) and anchovy (15%).
Fennel seed spent (FSS)-an inexpensive nutraceutical industrial spent has been used as an efficient biosorbent for the removal of Congo red (CR) from aqueous media. Results show that the conditions for maximum adsorption would be pH 2-4 and 30°C were ideal for maximum adsorption. Based on regression fitting of the data, it was determined that the Sips isotherm (R2 = 0.994, χ2 = 0.5) adequately described the mechanism of adsorption, suggesting that the adsorption occurs homogeneously with favorable interaction between layers with favorable interaction between layers. Thermodynamic analysis showed that the adsorption is favorable (negative values for ΔG°) and endothermic (ΔH° = 12-20 kJ mol-1) for initial dye concentrations of 25, 50, and 100 ppm. The low ΔH° value indicates that the adsorption is a physical process involving weak chemical interactions like hydrogen bonds and van der Waals interactions. The kinetics revealed that the adsorption process showed pseudo-second-order tendencies with the equal influence of intraparticle as well as film diffusion. The scanning electron microscopy images of FSS show a highly fibrous matrix with a hierarchical porous structure. The Fourier transform infrared spectroscopy analysis of the spent confirmed the presence of cellulosic and lignocellulosic matter, giving it both hydrophilic and hydrophobic properties. The investigations indicate that FSS is a cost-effective and efficient biosorbent for the remediation of toxic CR dye.
Peri-implant disease is usually caused by the accumulation of dental biofilm around the implant, and this biofilm can irradiate the gingiva tissue, which leads to inflammation and, more severely, to a deterioration of the bone structure. There is a concern regarding the removal of biofilm from the implant surface by using different hygiene instruments. Some hygiene instruments may have some effect on the dental implant surface, resulting in roughening or damage to the implant surfaces. This study reviewed the effects of titanium implant surfaces on different hygiene instruments. A literature search was conducted from PubMed, ScienceDirect, and Scopus databases for articles published from 1992 to 2021. A total of 19 full-text papers with keywords of interest that met all the eligibility criteria were selected. Surface roughness was evaluated with a scanning electron microscope and also using a profilometer, laser scanning, scanning probe, and atomic force microscopes. A metal curette produced a roughened surface on the titanium implant, but a plastic curette did not alter the surface. Instrumentation with rubber cups left the surface unchanged and appeared to smoothen the surface, whereas the air-powder abrasive instrumentation altered the surface with the presence of micro pits and pores. A conventional metal ultrasonic scaler showed significant surface topographical changes and scratches on both titanium surfaces, as a diode laser, light-emitting diode (LED), and laser treatment did not show any alteration on the rough and smooth titanium surfaces. Thus, a non-metallic instrument such as a plastic curette, rubber cups, and novel technology including diode laser, LED, and laser treatment is appropriate and can be used for debridement on smooth and machined titanium implant surfaces as well as sandblasted and acid-etched (SLA), titanium plasma-sprayed (TPS), and resorbable blasted media (RBM) surfaces. The use of metallic instruments should be avoided, and it is not recommended.