METHODS: Six porcine lumbar spines (L2-L5) were separated into 12 functional spine units. Bilateral total facetectomies and interlaminar decompression were performed for all specimens. Non-destructive loading to assess stiffness in lateral bending, flexion and extension as well as axial rotation was performed using a universal material testing machine.
RESULTS: PS and CS constructs were significantly stiffer than the intact spine except in axial rotation. Using the normalized ratio to the intact spine, there is no significant difference between the stiffness of PS and CS: flexion (1.41 ± 0.27, 1.55 ± 0.32), extension (1.98 ± 0.49, 2.25 ± 0.44), right lateral flexion (1.93 ± 0.57, 1.55 ± 0.30), left lateral flexion (2.00 ± 0.73, 2.16 ± 0.20), right axial rotation (0.99 ± 0.21, 0.83 ± 0.26) and left axial rotation (0.96 ± 0.22, 0.92 ± 0.25).
CONCLUSION: The CS-rod TLIF construct provided comparable construct stiffness to a traditional PS-rod TLIF construct in a 'standardized' porcine lumbar spine model.
METHOD: Twenty pieces of fourth-generation, biomechanical testing grade, left third metacarpal composite bones were used. Resin was used to create the holding block at both ends of the bone. An oscillating saw with 0.8 mm thick saw blade was used to osteotomize the metacarpal sawbones to create a midshaft transverse metacarpal fracture model. Ten pieces were fixed with a 2.0 mm titanium locking plate via unicortical screw purchase and 10 were fixed with a 2.0 mm, four holes, titanium dynamic compression plate, bicortical purchase of screws. They were subjected to cyclic load to failure testing three-point bending and torsion.
RESULTS: There were no significant difference in stiffness and cyclic three-point bending to failure between the unicortical locking plate group and the bicortical compression plate group. The bicortical compression plate group is stiffer and has a higher cyclic bending load to failure as compared to the unicortical locking plate group.
CONCLUSION: Unicortical locking plate fixation of metacarpal fracture can be reliably applied clinically to produce a strong and stable construct that allows early mobilization of the joints. This will not only reduce the complication rate of metacarpal plating, but also improve the functional outcome of the hand.
CASE PRESENTATION: A 57-year-old man presented to our orthopedic outpatient department with 3-months history of an unusual painful swelling at the operated area following DFO. The leakage of joint fluid from the penetrated suprapatellar pouch was assumed to be the reason for this complication.
CONCLUSIONS: The overall aim of this case report is to provide a lesson to budding surgeons who might experience a similar situation that cannot be easily explained, like the unexpected complication in the present case.
METHODS: Thirty patients who underwent distal volar locking plate for distal radius fracture were included in a retrospective study. In all 30 patients no dorsal and intra-articular screw penetration were detected on standard AP and lateral views of a plain radiograph. CT scan of the operated wrist was performed to determine the number of intra-articular and dorsal screw penetrations. Clinical examination was performed to determine the wrist functions in comparison to the normal wrist.
RESULTS: Nineteen wrists were noted to have screw penetration either dorsally or intraarticularly. The highest incidence is in the 2nd extensor compartment where 13 screws had penetrated with a mean of 2.46 mm. Six screws penetrated into the distal radial ulnar joint and five screws into the wrist joint with a mean of 2.83 mm and 2.6 mm, respectively. However, there was no incidence of tendon irritation or rupture.
CONCLUSIONS: This study demonstrated a high incidence of dorsal and intra-articular screw penetration detected by CT scan which was not apparent in plain radiograph. We recommend that surgeons adhere to the principle of only near cortex fixation and downsizing the locking screw length by 2 mm.
Material and Methods: We conducted a retrospective review of patients who underwent surgery for isolated scaphoid fractures over a 15 years period from December 2000 to December 2015. Only patients who underwent open surgery with bone grafting were included. They were divided into a group treated with a single screw fixation, and another group treated with screw and K-wire fixations.
Results: Forty-four (58.7%) patients had single screw fixation and 31 (41.3%) had screw augmented with K-wire fixation. The overall union rate was 88.0%, with an overall mean time to union of 5.3 months. There was no difference in union rate (p=0.84) and time to union (p=0.66) between the single screw group and combined screw and K-wire group. Univariate analysis found that older age (t=-2.11, p=0.04) had a significant effect on union rate. Regression model showed that age had a significant effect on months to union.
Conclusion: In open fixation of scaphoid fractures with compression screw and bone grafting, union rate and time to union is comparable whether or not screw fixation was augmented with an intracarpal K-wire. There was no increased risk of complications associated with augmented screw. Age of patient affected time to union and union rate.
Materials and Methods: Fifteen patients with malunited intertrochanteric fractures who presented between January 2011 to January 2013 were managed by Valgus osteotomy with DHS fixation and were followed-up for a minimum period of three years.
Results: There was a male preponderance seen in our study with the right hip being more commonly affected. The most common mode of injury was slip and fall followed by road traffic accidents. The duration of native treatment ranged from seven to 12 weeks and the time of presentation to the hospital ranged from four to nine months following injury. Pre-operative mean neck shaft angle was 94.73° while it was 134.6° post-operatively. The mean pre-operative Harris hip score was 72.33 and it was 91 at follow-up. All patients were happy with the procedure and the functional outcome.
Conclusion: Valgus osteotomy with DHS fixation is an effective procedure in the management of malunited intertrochanteric fractures. It corrects the limb length discrepancy, restores the decreased neck shaft angle, improves range of movement, restores the integrity of the abductor mechanism of the hip and gives good functional results.
PURPOSE: The C1 and C2 laminas in the Malaysian Malay population were analyzed for the feasibility of fitting 3.5-mm laminar screws in a cross configuration.
OVERVIEW OF LITERATURE: Morphometric analysis of the C1 and C2 laminas has been performed for various populations but not for the Malaysian Malay population.
METHODS: A total of 330 CT cervical images were measured to establish the bicortical diameter of the C1 and C2 laminas as well as their height and length. The C1 posterior tubercle bicortical diameter and height were also determined from these images. All parameters were measured up to 0.1 mm, and statistical analysis was performed using IBM SPSS Statistics ver. 24.0 (IBM Corp., Armonk, NY, USA). An independent t -test and the Pearson chi-square test were used to determine the mean difference and screw acceptance.
RESULTS: The means of the C1 lamina measurements were 5.79±1.19 mm in diameter, 9.76±1.51 mm in height, and 20.70±1.86 mm in length. The means of the measurements of the posterior tubercle were 7.20±1.88 mm in diameter and 10.51±1.68 mm in height. The means of the C2 lamina measurements were 5.74±1.31 mm in diameter, 11.76±1.69 mm in height, and 24.96±2.56 mm in length. Overall 65.5% of C1 and 80.3% of C2 laminas are able to accept 3.5-mm screws in a cross configuration. Screw acceptability is similar between the right and left sides (p >0.05). However, males have a higher screw acceptability compared with females (p <0.05), except for the C2 left lamina.
CONCLUSIONS: It is feasible to insert a 3.5-mm screw in a cross configuration in the C1 and C2 laminas of the Malaysian Malay population, especially in males. However, a CT scan should be performed prior to the operation to determine screw acceptability and to estimate screw sizes.
Materials and Methods: A retrospective study analysed 120 adult patients operated between 2014-2017 using modified short PFN for intertrochanteric fractures, having a minimum follow-up of 12 months. Clinical and radiological parameters including tip-apex distance (TAD), position of tip of lag screw in femoral head, lateral slide of lag screw as well as length of anti-rotation screw were measured. Final functional outcome was assessed using Barthel's index and Kyle's criteria.
Results: Good reduction was achieved in 90.83% cases and 79.16% had ideal placement of lag screw in femoral head. Intra-operative difficulties were encountered in 13.33% (n=16). Mean TAD AP (anteroposterior) was 11.8mm, TAD LAT (lateral) was 11.0mm and mean TAD TOT was 22.8mm. Overall mean lateral slide was 3.20mm and it was more in unstable fracture. We had five mechanical failures, one patient with screw breakage without loss of reduction and two peri-implant fractures after union. 81.66% returned to pre-injury levels of activity with 88.33% good to excellent outcome as per Kyle's criteria.
Conclusion: Although, not devoid of complications, modified short PFN results in good functional recovery of patients with intertrochanteric fractures of femur.