A binary salt system utilizing lithium iodide (LiI) as the auxiliary component has been introduced to the N-phthaloylchitosan (PhCh) based gel polymer electrolyte consisting of ethylene carbonate (EC), dimethylformamide (DMF), tetrapropylammonium iodide (TPAI), and iodine (I2) in order to improve the performance of dye-sensitized solar cell (DSSC) with efficiency of 6.36%, photocurrent density, JSC of 17.29mAcm-2, open circuit voltage, VOC of 0.59V and fill factor, FF of 0.62. This efficiency value is an improvement from the 5.00% performance obtained by the DSSC consisting of only TPAI single salt system. The presence of the LiI in addition to the TPAI improves the charge injection rates and increases the iodide contribution to the total conductivity and both factors contribute to the increase in efficiency of the DSSC. The interaction behavior between polymer-plasticizer-salt was thoroughly investigated using EIS, FTIR spectroscopy and XRD.
Starch blend films made from sago and mung bean were prepared by casting with glycerol as the plasticizer and subsequently exposed to ultraviolet (UV) irradiation for 2 h. The films were characterized by thickness, moisture sorption isotherms, X-ray diffraction and Fourier transform infrared (FTIR) spectroscopy. All films produced were colorless while incorporation of glycerol resulted in more flexible and manageable films. Moisture sorption isotherms for all films showed sigmoidal shape and the control films showed slightly higher curve than treated films. While for X-ray analysis, the control and treated films for all formulations showed similar pattern, however for treated films showed more crystalline character. UV radiation showed affect on X-ray diffraction and sorption isotherms; however the UV radiation did not affect the spectra pattern of FTIR.
This study investigated consequent functional effects (mechanical and physical) on Gelatin/ CMC/Chitosan composite films from the addition of sorbitol. With glycerol as a plasticizer, solutions for Gelatin/CMC/Chitosan composite films containing graduated sorbitol concentrations (0%, 5%, 10%, 15%, 20%, 25% and 30%), were cast on a petri dish and oven dried at 45˚C. The fabricated films were then characterized for tensile strength, elongation at break (EAB) and puncture resistance (mechanical properties); as well as film thickness, water vapor permeability (WVP), thermal properties, light transmittance and transparency (UV and visible light transmission), biodegradability, and X-ray diffraction (physical properties). Results indicated that by increasing sorbitol concentration, melting point and tensile strength decreased overall (p
A study on the quality of water abstracted for potable use was conducted in the Selangor River basin from November 2008 to July 2009. Seven sampling sites representing the intake points of water treatment plants in the basin were selected to determine the occurrence and level of 15 organochlorine pesticides (OCPs), six phthalate esters (PAEs) and bisphenol A (BPA). Results indicated OCPs were still detected regularly in 66.1 % of the samples with the Σ(15)OCPs ranging from 0.6-25.2 ng/L. The first data on PAEs contamination in the basin revealed Σ(6)PAEs concentrations were between 39.0 and 1,096.6 ng/L with a median concentration of 186.0 ng/L while BPA concentration ranged from <1.2 to 120.0 ng/L. Although di-n-butyl phthalate was detected in all the samples, concentrations of di-ethyl(hexyl)phthalate were higher. Sampling sites located downstream recorded the highest concentrations, together with samples collected during the dry season. Comparison of the detected contaminants with the Department of Environment Water Quality Index (DOE-WQI) showed some agreement between the concentration and the current classification of stream water. While the results suggest that the sites were only slightly polluted and suitable to be used as drinking water source, its presence is cause for concern especially to the fragile firefly "Pteroptyx tener" ecosystem located further downstream.
The occurrence of 14 phthalate metabolites was found in human urine samples collected from seven Asian countries: China, India, Japan, Korea, Kuwait, Malaysia, and Vietnam. Phthalate metabolites were found in all samples, indicating widespread exposure of humans to phthalates in these Asian countries. The highest total (the sum of 14 phthalates) phthalate metabolite concentrations were found in samples collected from Kuwait (median: 1050 ng/mL), followed in decreasing order by samples from India (389 ng/mL), China (234 ng/mL), Vietnam (133 ng/mL), Japan (120 ng/mL), Korea (117 ng/mL), and Malaysia (94.9 ng/mL). The creatinine-adjusted median concentrations of total phthalates for urine samples from Kuwait, India, China, Vietnam, Japan, Korea, and Malaysia were 692, 506, 289, 119, 103, 104, and 169 μg/g creatinine, respectively. Monomethyl phthalate (mMP), monoethyl phthalate (mEP), mono (2-isobutyl phthalate) (miBP), mono-n-butyl phthalate (mBP), and metabolites of di-(2-ethylhexyl) phthalate (DEHP) were the dominant compounds, collectively accounting for >95% of the total concentrations in the samples from the seven countries. The profiles of urinary phthalate metabolite concentrations varied among the samples collected from the seven countries. Urine samples from Kuwait contained the highest concentrations of mEP (median: 391 ng/mL), mBP (94.1 ng/mL), and the metabolites of DEHP (202 ng/mL), whereas samples from China and Japan contained the highest concentrations of miBP (50.8 ng/mL) and mMP (17.5 ng/mL), respectively. mEP was the predominant metabolite in urine samples from India and Kuwait (accounting for 49% of the total), mBP and miBP were the predominant compounds in samples from China (52%), and DEHP metabolites were the predominant compounds in samples from Korea (46%) and Vietnam (52%). Based on the urinary concentrations of mEP, mBP, miBP, and DEHP metabolites of the samples from the seven Asian countries, we estimated daily intake rates of diethyl phthalate (DEP), dibutyl phthalate (DBP), and DEHP. The results indicated that people in the seven Asian countries are exposed to DEP, DBP, and DEHP at levels well below the reference doses (RfD) suggested as unsafe by the U.S. Environmental Protection Agency (EPA). The estimated exposure doses to DEHP in Kuwait, however, were above the RfD recommended by the EPA.
Fourier transform infrared (FT-IR) spectroscopic studies have been undertaken to investigate the interactions among components in a system of hexanoyl chitosan-lithium trifluoromethanesulfonate (LiCF(3)SO(3))-diethyl carbonate (DEC)/ethylene carbonate (EC). LiCF(3)SO(3) interacts with the hexanoyl chitosan to form a hexanoyl chitosan-salt complex that results in the shifting of the N(COR)(2), CONHR and OCOR bands to lower wavenumbers. Interactions between EC and DEC with LiCF(3)SO(3) has been noted and discussed. Evidence of interaction between EC and DEC has been obtained experimentally. Studies on polymer-plasticizer spectra suggested that there is no interaction between the polymer host and plasticizers. Competition between plasticizer and polymer on associating with Li(+) ions was observed from the spectral data for gel polymer electrolytes. The obtained spectroscopic data has been correlated with the conductivity performance of hexanoyl chitosan-based polymer electrolytes.
In Malaysia, inexpensive toys are sold in various urban and rural shops. Although safety regulations for toys are available in Malaysia there are limited reports about the chemicals in toys. Thus, this study aimed to assess the levels of phthalates (bis-[2-ethylhexyl] phthalate [DEHP], diethyl phthalate [DEP], diisobutyl phthalate [DiBP] and dibutyl phthalate [DBP]) in inexpensive toys sold at local markets in Kuala Lumpur (Malaysia) and its health risks to children. All 30 toys analysed exceeded the European Union limit (0.1 % by mass) indicating that the phthalate used as plasticizers is still prominent in toys. Bis-[2-ethylhexyl] phthalate (DEHP) was the highest detected phthalate in toy sample which was manufactured in Malaysia and sold without Malaysian Conformity Mark. Significant association was found between phthalate levels and country, indicating a need to monitor and raise public awareness about potential toxic chemicals in inexpensive toys and children's products. There are few inexpensive toys that have a hazard index value of more than one, which is associated with developmental toxicity and causes developmental effects in children. Given the severity and complexity of these toys to children health, there is a need for regular monitoring and effective enforcements to develop an acceptable baseline level of children toys products manufactured in or imported to Malaysia. Furthermore, risk management efforts should also include all the stakeholders involved in toy production, policy makers as well as consumers to ensure only toy products with proper labels being sole and purchased.
It is well known that the endocrine-disrupting chemical (EDC) dibutylphthalate (DBP) inhibits testosterone synthesis and can lead to feminisation in male laboratory animals. Moreover, it has long been speculated that human exposure would result in the similar effects, but this is difficult to study because specific human exposure cohorts are rare. We report increases in the incidences of hypospadias (p<0.05), cryptorchidism (p<0.05) and breast cancer (p<0.05) in the children of New Zealand soldiers who served in Malaya (1948-1960) and were exposed to DBP applied daily to their clothing as an acaricide to prevent tick-transmitted bush typhus. In addition, we modelled absorption of DBP from the soldiers' clothing and using published data for skin absorption, and calculated a large theoretical absorbed dose of 64 mg/kg body weight/day which is similar to DBP's lowest observed adverse effect level (LOAEL) of 50 mg/kg body weight/day and thus indicates a biological effect is possible. This is the first report of a multigenerational developmental effect following DBP exposure in human males.
Difficulty in swallowing tablets or capsules has been identified as one of the contributing factors to non-compliance of geriatric patients. Although orally disintegrating tablet was designed for fast disintegration in mouth, the fear of taking solid tablets and the risk of choking for certain patient populations still exist.
The purpose of this work was to study the effect of various permeation enhancers on the permeation of salbutamol sulphate (SS) buccal patches through buccal mucosa in order to improve the bioavailability by avoiding the first pass metabolism in the liver and possibly in the gut wall and also achieve a better therapeutic effect. The influence of various permeation enhancers, such as dimethyl sulfoxide (DMSO), linoleic acid (LA), isopropyl myristate (IPM) and oleic acid (OA) on the buccal absorption of SS from buccal patches containing different polymeric combinations such as hydroxypropyl methyl cellulose (HPMC), carbopol, polyvinyl alcohol (PVA), polyvinyl pyrollidone (PVP), sodium carboxymethyl cellulose (NaCMC), acid and water soluble chitosan (CHAS and CHWS) and Eudragit-L100 (EU-L100) was investigated. OA was the most efficient permeation enhancer increasing the flux greater than 8-fold compared with patches without permeation enhancer in HPMC based buccal patches when PEG-400 was used as the plasticizer. LA also exhibited a better permeation enhancing effect of over 4-fold in PVA and HPMC based buccal patches. In PVA based patches, both OA and LA were almost equally effective in improving the SS permeation irrespective of the plasticizer used. DMSO was more effective as a permeation enhancer in HPMC based patches when PG was the plasticizer. IPM showed maximum permeation enhancement of greater than 2-fold when PG was the plasticizer in HPMC based buccal patches.
The main goal of the present work was to develop a value-added product of biodegradable material for sustainable packaging. The use of agriculture waste-derived carboxymethyl cellulose (CMC) mainly is to reduce the cost involved in the development of the film, at present commercially available CMS is costly. The main focus of the research is to translate the agricultural waste-derived CMC to useful biodegradable polymer suitable for packaging material. During this process CMC was extracted from the agricultural waste mainly sugar cane bagasse and the blends were prepared using CMC (waste derived), gelatin, agar and varied concentrations of glycerol; 1.5% (sample A), 2% (sample B), and 2.5% (sample C) was added. Thus, the film derived from the sample C (gelatin + CMC + agar) with 2.0% glycerol as a plasticizer exhibited excellent properties than other samples A and B. The physiochemical properties of each developed biodegradable plastics (sample A, B, C) were characterized using Fourier Transform Infra-Red (FTIR) spectroscopy and Differential Scanning Calorimetry (DSC), Thermogravimetric analysis (TGA). The swelling test, solubility in different solvents, oil permeability coefficient, water permeability (WP), mechanical strength of the produced material was claimed to be a good material for packaging and meanwhile its biodegradability (soil burial method) indicated their environmental compatibility nature and commercial properties. The reflected work is a novel approach, and which is vital in the conversion of organic waste to value-added product development. There is also another way to utilize commercial CMC in preparation of polymeric blends for the packaging material, which can save considerable time involved in the recovery of CMC from sugarcane bagasse.
Polyethylene is a widely used packaging material, but its non-biodegradable nature can lead to waste
disposal problems. This increases the concern in research and development of biodegradable plastics from natural resource as alternatives to petroleum-derived plastics. In this study, biodegradable plastic composites were prepared by blending thermoplastic starch with natural rubber in the present of glycerol as plasticizer. Local sago starch was cast with 0.5 to 10% of natural rubber to prepare the bioplastic. The products were characterized by differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), water absorption test, biodegradable test, hydrolysis test, and mechanical analysis. Meanwhile, composite with natural rubber latex was increased from 0.5 to 10% showing that the melting temperature is in the range of 120 to 150˚C, but with no significant difference. The water absorption characteristics, biodegradability, and tensile strength decreased by 11.21%, 30.18%, and 20.733 MPa, respectively. However, the elongation at break was increased from 26.67 to 503.3%. The findings of this study showed that sago starch has a great potential in bioplastic production with good miscibility and compatibility.
Antibacterial effect of modified sago starch-alginate edible film incorporating lemongrass oil at various concentrations was studied. Edible films were prepared from a mixture of modified sago starch and alginate. Lemongrass oil (0.1 - 0.4%, v/w) and glycerol (0 and 20%, w/w) were incorporated in the films to act as natural antimicrobial agent and plasticizer, respectively. The films were characterized for antibacterial activity against food pathogenic bacteria such as Escherichia coli O157:H7, Salmonella Enteritidis and Staphylococcus aureus. The edible film exhibited antibacterial activity against Escherichia coli O157:H7 and Salmonella Enteritidis by using agar diffusion assay method. For films tested against Escherichia coli O157:H7, the zone of inhibition increased significantly (p < 0.05) with addition of lemongrass oil at all levels both in the presence and absence of glycerol. The films also significantly (p < 0.05) inhibited the growth of Salmonella enteritidis only with 0.4% lemongrass oil (in the presence and absence of glycerol). However, the films containing lemongrass oil did not show any inhibition effect on Staphylococcus aureus.
The objective of this research was to formulate an aerosol concentrate containing haruan (Channa
striatus) water extract that would produce a thin film when sprayed onto a wound and could be used for wound dressing. The aerosol concentrates were formulated with various polymer and plasticiser mixtures and tested in dispersion systems. The polymers evaluated were hydroxypropyl methylcellulose (HPMC), carboxymethylcellulose sodium (CMC Sodium), acacia, tragacanth, chitosan, gelatine and gelatine (bloom 151–160), all at concentrations of 2%. The plasticisers evaluated were polyethylene glycol (PEG) 400 and 4000, glycerine, propylene glycol, and triacetin. Films were prepared from film-forming dispersions by casting techniques. Film-forming dispersions were characterised in terms of pH, density, surface tension, rheological properties, particle size distribution, and tackiness. Based on these evaluations, HPMC was chosen as the best polymer. It produced a film with the expected qualities and was easy to reproduce in the form of dispersions or as thin transparent films. Glycerine was judged as the most appropriate plasticiser because it produced the concentrate having the desired qualities and properties expected from an aerosol concentrate.
The current research trend for excellent miscibility in polymer mixing is the use of plasticizers. The use of most plasticizers usually has some negative effects on the mechanical properties of the resulting composite and can sometimes make it toxic, which makes such polymers unsuitable for biomedical applications. This research focuses on the improvement of the miscibility of polymer composites using two-step mixing with a rheomixer and a mix extruder. Polylactic acid (PLA), chitin, and starch were produced after two-step mixing, using a compression molding method with decreasing composition variation (between 8% to 2%) of chitin and increasing starch content. A dynamic mechanical analysis (DMA) was used to study the mechanical behavior of the composite at various temperatures. The tensile strength, yield, elastic modulus, impact, morphology, and compatibility properties were also studied. The DMA results showed a glass transition temperature range of 50 °C to 100 °C for all samples, with a distinct peak value for the loss modulus and factor. The single distinct peak value meant the polymer blend was compatible. The storage and loss modulus increased with an increase in blending, while the loss factor decreased, indicating excellent compatibility and miscibility of the composite components. The mechanical properties of the samples improved compared to neat PLA. Small voids and immiscibility were noticed in the scanning electron microscopy images, and this was corroborated by X-ray diffraction graphs that showed an improvement in the crystalline nature of PLA with starch. Bioabsorption and toxicity tests showed compatibility with the rat system, which is similar to the human system.
The aim of this study was to investigate the functional properties of chicken skin gelatin films with varied concentrations of a hydrophilic plasticizer. Gelatin film solutions with different glycerol concentrations A(control), B(5%), C(10%), D(15%) and E(20%), were stirred at 45°C for 20min and oven dried at 45°C. Film characterization determination were included, tensile strength (TS), elongation at break (EAB), water vapor permeability (WVP), solubility, transparency, moisture content, Fourier Transform Infrared Spectroscopy (FTIR), and X-ray Diffraction (X-RD). Glycerol added resulted in improvement of TS and WVP properties. Film B (5% glycerol) demonstrated low EAB (106%), WVP (0.0175 g.mm/h.m2.k.Pa) and solubility (58.64%), but with high TS (3.64 MPa), moisture content (16.0%), UV light transmission (0.04%) and transparency (0.81) compared to films C, D and E. FTIR spectrum analyses demonstrated an aliphatic alcohol group only for Film E (20% glycerol). Hence, chicken skin gelatin film at 5% glycerol concentration showed the most promising potential for industrial food processing applications.