Hybrid composites of polypropylene (PP)/nanoclay (NC)/glass fiber (GF) were prepared byextrusion and injection molding. Molded specimens were analyzed by transmission electron microscopy (TEM), thermogravimetric analysis (TGA), tensile and flexural tests. TEM results revealed NC particle intercalation. TGA results showed that the incorporation of clay into the GF composite improves the thermal stability of the material. The initial thermal decomposition temperatures also shifted to higher values. Incorporation of GF into PP lowers the tensile strength of the binary composite, indicating poor fiber-matrix interfacial adhesion. However, introducing NC increased the strength of the ternary composites. Tensile modulus was enhanced with the incorporation of GF and further increased with an introduction of NC. Flexural strength and flexural modulus are both enhanced with an increase in GF and NC loading.
The combustion characteristics of refuse derived fuel (RDF) in a fluidized bed have been studied. The gross heating value (GHv) of the RDF was 14.43 MJIkg with moisture content of 25% by weight. Parameters of interest for sustainable bed combustion were the fluidization number and primary air factor. The study was performed in a rectangular fluidized bed combustor with dimensions of 0.3 m in width, 0.7 m in length and 2 m in height. Sand with mean particle size of 0.34 mm was used as a fluidization medium. The sand bed height was at 0.3 m above the standpipes air distributor. The range of fluidization number under investigation was 5-7 II fin which 5 II newas found to be the optimum. The study was continued for the determination of the optimum primary air factor with the selected range of primary air factors being 0.6, 0.8, 1.0 and 12 in experiments conducted at 5 Unit The final results showed that the optimum primary air factor was at 0.8. An energy balance was also performed to determine the thermal efficiency of the combustion. It was concluded that the thermal efficiency depended on the bed temperature and the primary air factor being used.
The lack of efficient hydrogen storage material is one of the bottlenecks for the large-scale implementation of hydrogen energy. Here, a series of new hydrogen storage materials, i.e., anilinide-cyclohexylamide pairs, are proposed via the metallation of an aniline-cyclohexylamine pair. DFT calculations show that the enthalpy change of hydrogen desorption (ΔHd) can be significantly tuned from 60.0 kJ per mol-H2 for the pristine aniline-cyclohexylamine pair to 42.2 kJ per mol-H2 for sodium anilinide-cyclohexylamide and 38.7 kJ per mol-H2 for potassium anilinide-cyclohexylamide, where an interesting correlation between the electronegativity of the metal and the ΔHd was observed. Experimentally, the sodium anilinide-cyclohexylamide pair was successfully synthesised with a theoretical hydrogen capacity of 4.9 wt%, and the hydrogenation and dehydrogenation cycle can be achieved at a relatively low temperature of 150 °C in the presence of commercial catalysts, in clear contrast to the pristine aniline-cyclohexylamine pair which undergoes dehydrogenation at elevated temperatures.
Catalytic co-pyrolysis (CCP) of spent coffee ground (SCG) and cellulose over HZSM-5 and HY was characterized thermogravimetrically, and a catalytic pyrolysis of two samples was conducted using a tandem micro reactor that directly connected with gas chromatography-mass spectrometry. To access the more fundamental investigations on CCP, the effects of the zeolite pore structure, reaction temperature, in-situ/ex-situ reaction mode, catalyst to feedstock ratio, and the SCG and cellulose mixing ratio were experimentally evaluated. The temperature showing the highest thermal degradation rate of cellulose with SCG slightly delayed due to the interactions during the thermolysis of two samples. HZSM-5 in reference to HY produced more aromatic hydrocarbons from CCP. With respect to the reaction temperature, the formation of aromatic hydrocarbons increased with the pyrolytic temperature. Moreover, the in-situ/ex-situ reaction mode, catalyst/feedstock, and cellulose/SCG ratio were optimized to improve the aromatic hydrocarbon yield.
The rapid urban expansion in East-Asian cities has increased the need for comfortable public spaces. This study presents field measurements and parametric simulations to evaluate the microclimatic characteristics in a university campus in the tropical climate of Kuala Lumpur, Malaysia. The study attempts to identify the thermally uncomfortable areas and their physical and design characteristics while debating on the circumstances of enhancing the outdoor comfort conditions for the campus users. Simulations in Envi-met and IES-VE are used to investigate the current outdoor thermal conditions, using classic thermal metric indices. Findings show high levels of thermal discomfort in most of the studied spaces. As a result, suggestions to improve the design quality of outdoor areas optimizing their thermal comfort conditions are proposed. The study concludes that effective re-design of outdoor spaces in the tropics, through adequate attention to the significant impacts of shading and vegetation, can result in achieving outdoor spaces with high frequency of use and improved comfort level.
Thermal imbalances are very common during surgery. Hypothermia exposes the patient to post-operative shivering, cardiac dysfunction, coagulopathy, bleeding, wound infection, delayed anesthesia recovery, prolonged hospital stay and increased hospitalization cost. There are many factors contributing to intraoperative hypothermia. This is a prospective cohort study conducted through observation and measurement of pediatric surgical patients' temperature. Convenience sampling methods were used in this study. Initial skin temperature and core temperature at 10 min, 30 min,1 h, 2 h, 3 h, 4 h, 5 h, 6 h and at the end of surgery were recorded. Body temperature was monitored from time of transfer to the operating table until recovery and discharge to the respective pediatric ward. The overall incidence of intraoperative hypothermia was still very high at about 46.6% even though active and passive temperature management were carried out during surgery. Patient's age, body weight, duration of surgery, type of surgery, intraoperative blood loss, type of anesthesia and operating room temperature were factors that contributed to intraoperative hypothermia. Hypothermia is common in surgery, especially in major and long duration surgery. Intraoperative hypothermia can be life threatening if it is not handled carefully. Various methods are used before, during and after surgery to maintain a patient's body temperature within the normothermia range. The use of an active warming device like the Bair Hugger® air-forced warming system seems to be a good method for reducing the risk of intraoperative hypothermia and effectively maintaining body temperature for all major and minor surgeries.
Matched MeSH terms: Body Temperature; Body Temperature Regulation; Skin Temperature*
Palm oil mill effluent (POME) is a highly polluted wastewater that consists of a high organic content of 4-5% total solids; a potential renewable energy source. A waste to energy study was conducted to improve biogas production using POME as substrate by ultrasonication pretreatment at mesophilic temperatures. The effect of temperature on the specific growth rate of anaerobes and methanogenic activity was investigated. Five sets of assays were carried out at operating temperatures between 25 °C and 45 °C. Each set consisted of two experiments using identical anaerobic sequencing batch reactors (AnSBR); fed with raw POME (control) and sonicated POME, respectively. The ultrasonication was set at 16.2 min ultrasonication time and 0.88 W mL-1 ultrasonication density with substrate total solids concentration of 6% (w/v). At 25 °C, biogas production rate and organic matter removal exhibited lowest values for both reactors. The maximum organic degradation was 96% from AnSBR operated at 30 °C fed with sonicated POME and 91% from AnSBR operated at 35 °C fed with unsonicated POME. In addition, the methane yield from AnSBR operated at 30 °C was enhanced by 21.5% after ultrasonication pretreatment. A few normality tests and a t-test were carried out. Both tests indicated that the residuals of the experimental data were normality distributed with mean equals to zero. The results demonstrated that ultrasonication treatment was a promising pretreatment to positively affect the organic degradation and biogas production rates at 30-35 °C.
Foam flooding technique, commonly known as foam assisted water alternating gas method (FAWAG) has been identified as an effective chemical enhanced oil recovery (CEOR) technique. The ability of EOR-foam to sweep oil in low permeable zones makes it important displacement fluid in the oil industry. However, extreme reservoir conditions such as temperature, pressure and salinity have detrimental effects on the stability and the overall performance of the EOR-foam. Consequently, understanding foam stability and performance under different conditions is crucial for long term oil field application. This paper discusses the current status of the EOR-foam stability, performance and challenges from laboratory studies to field application perspective. The paper also highlights the knowledge gaps which require further research for successful field application.
This study analyzes the heat transfer of a thin film flow on an unsteady stretching sheet in nanofluids. Three different types of nanoparticles are considered; copper Cu, alumina Al2O3 and titania TiO2 with water as the base fluid. The governing equations are simplified using similarity transformations. The resulting coupled nonlinear differential equations are solved by the Homotopy Analysis Method (HAM). The analytical series solutions are presented and the numerical results obtained are tabulated. In particular, it shows that the heat transfer rate decreases when nanoparticles volume fraction increases.
The increasing demands of natural gas pushes energy industries to explore the reservoirs contain high CO2 concentration
and impurities including heavy hydrocarbons. High efficiency of using membrane technology in CO2
-natural gas separation
has extended its potential application to offshore environment. Due to the limited studies related with the separation of
CO2
under offshore conditions, the present work has investigated the separation performance of a commercial membrane
in removing bulk CO2
from methane at elevated pressure condition. A wide range of offshore operating conditions
including pressure from 10 to 50 bar, CO2
concentration from 25 to 70% and temperature of 30o
C, 40o
C and 50o
C were
studied. High relative CO2 permeance and relative CO2
/CH4
selectivity were observed when the pressure and the CO2
concentration increased. This work, therefore substantial is to bridge the gap and facilitates the application of membrane
technology for offshore operating conditions.
FERMSOSTAT is a developed laboratory scale solid state fermenter. It is a horizontal stirrer drum bioreactor with about 70 L capacities. The fermenter is made of stainless steel which is anti-corrosive and non-toxic to the process organism. The fermenter is equipped with sets of control systems for temperature, agitation, aeration and also outlets for substrate sampling as well as inlets for inoculation and substrate additions. The uniqueness of this FERMSOSTAT system is its ability to carry out in situ substrate sterilization and extraction of enzymes at the end of SSF process. Moreover, the mixing system provided by FERMSOSTAT can be performed either full or half mixing as well as forward or reverse mixing. Furthermore, the mixing can be programmed to run at certain agitation rate and time interval during the fermentation process to prevent or reduce damage to the fungus mycelia. FERMSOSTAT is a developed SSF bioreactor and not an improvement of any existing one. The performances of FERMSOSTAT have been evaluated. Under optimum solid state fermentation conditions, about 63.4, 397 and 3.21 U/g of CMCase, xylanase and FPase activities were detected, which were higher compared to the tray system.
Response surface methodology (RSM) with central composite design (CCD) was applied to optimize key factors affecting
hydrogen production (HP) from diluted acid hydrolysate of water-hyacinth stem (WHS) by heat-treated anaerobic sludge
in a batch fermentation process. Key factors affecting namely substrate concentration and initial pH was investigated.
The results indicated that substrate concentration and initial pH had significantly effects on HP (p<0.05). A maximum HP
hydrogen production rate and hydrogen yield of 182.7 mmol H2
/L, 2.81 mmol H2
/L h and 0.84 mol H2
/mol hexose were
obtained under the optimum conditions i.e. substrate concentration of 4.06 g/L and initial pH of 5.81. The total energy
production from the fermentative of WHS hydrolysate was 1.97 kJ.
A mild and effective synthesis of resorcinol-furfural (RF) thermosetting resin was proposed with ethanol as a distinctive solvent, which, as a usually neglected factor, was shown to not only help form a homogeneous reaction system but also observably reduce the energy barriers between the early intermediates and transition states in addition reactions by explicit solvent effects, drawn from theoretical calculation conclusions. Besides, the para-additions on aromatic rings were more dominant than ortho-additions with the same reactants, which affected the final link types of monomers verified by Fourier transform infrared spectroscopy and two-dimensional nuclear magnetic resonance tests. The prepared resin can be assigned to a relatively fast gel speed and a high residual mass (65.25%) after pyrolysis in a N2 atmosphere by adjusting the molar ratios of F to R, and the curing of that was a complex reaction, with a curing temperature around 149 °C and an activation energy of about 49.11 kJ mol-1 obtained by the Kissinger method.
The global economy is threatened by the depletion of fossil resources and fluctuations in fossil fuel prices, and thus it is necessary to exploit sustainable energy sources. Carbon-neutral fuels including bio-oil obtained from biomass pyrolysis can act as alternatives to fossil fuels. Co-pyrolysis of lignocellulosic biomass and plastic is efficient to upgrade the quality of bio-oil because plastic facilitates deoxygenation. However, catalysts are required to produce bio-oil that is suitable for potential use as transportation fuel. This review presents an overview of recent advances in catalytic co-pyrolysis of biomass and plastic from the perspective of chemistry, catalyst, and feedstock pretreatment. Additionally, this review introduces not only recent research results of acid catalysts for catalytic co-pyrolysis, but also recent approaches that utilize base catalysts. Future research directions are suggested for commercially feasible co-pyrolysis process.
Storage temperature and duration plays an important role in meat processing. Observations in poultry processing plants have shown a serious deviation in storage condition compared to the recommended procedures. Furthermore, there is still a paucity of evidence on the effects of storage temperature and duration on meat quality and microbial population. The aim of this study was to determine the effects of different temperature and duration during storage on physico-chemical properties and microbiological quality of broiler chicken Pectoralis major muscle. Eighty birds were slaughtered and processed, following which the packed boneless breast (PBB) (each bird was to provide two breast muscle samples; left breast and right breast) was divided into four groups, each consisted of 40 PBB. Each group was subsequently assigned to storage either at 4 °C, -10 °C, -18 °C or -40 °C, for 24 h before 20 PBB samples from each group were transported to the respective laboratory for meat quality and microbiological analysis. The remaining 20 PBB from each storage temperature were stored for 72 h before being transported for analysis. Results have shown significant increases in drip loss and cooking loss as the storage temperature decreases. Similarly, storage duration significantly affected cooking loss, of which, samples stored for 72 h exhibited higher cooking loss compared to those stored for 24 h. For color, significant differences were only observed in lightness (L*) and redness (a*) values. Longer duration of storage had significantly improved tenderness whereby, samples that have been stored for a shorter duration presented higher pH values. Populations of coliform and Salmonella decreased significantly with decreasing temperature and increasing storage duration.
In this study, solid coconut waste and CaO/PVA was used as raw material and catalyst respectively to produce biodiesel through in situ transesterification. Both, raw material and catalyst were packed in a packed bed reactor. The reaction was fixed for 3 h and the mixing was kept constant at 350 rpm. The highest biodiesel yield of 95% was obtained at reaction temperature of 61 °C with catalyst loading (CaO/PVA) of 2.29 wt% and methanol to solid ratio of 12:1. CaO-waste derived catalyst has been successfully proven to be utilized as heterogeneous base catalyst for the production of biodiesel from solid coconut waste.
Low temperature thermal pre-treatment is a low-cost method to break down the structure of extracellular polymeric substances in waste activated sludge (WAS) while improving the sludge biodegradability. However, previous models on low temperature thermal pre-treatment did not adequately elucidate the behaviour of sludge hydrolysis process for the duration ranging from 5 to 9 h. Therefore, this work had developed an inclusive functional model to describe the kinetics of sludge hydrolysis for a wide range of treatment conditions (30 °C-90 °C within 0 and 16 h). As compared with treatment duration, the treatment temperature played a greater impact in solubilizing WAS. Accordingly, the 90 °C treatment had consistently produced WAS with the highest degree of solubility. Nonetheless, the mediocre discrepancies between 90 °C and 75 °C may challenge the practicality of increasing the treatment temperatures beyond 75 °C. The effects of treatment duration on soluble chemical oxygen demand, soluble carbohydrate and soluble protein were only significant during the first 4 h, except for humic substances release that continued to increase with treatment duration. Finally, a good fit with R2 > 0.95 was achieved using an inclusive multivariate non-linear model, substantiating the functionality to predict the kinetics of sludge hydrolysis at arbitrary treatment conditions.
Membrane distillation (MD) is a thermally driven technology applied in desalination and water reuse with utilisation of sustainable energy. However, algal organic matter (AOM) could foul membrane critically and plague MD's long-term operational stability. In this study, the soluble extracellular polymeric substance (sEPS) and intracellular organic matter with bound extracellular polymeric substance (IOM + bEPS) of two algal species (Amphora coffeaeformis and Navicula incerta) were exposed to 60 °C, 70 °C and 80 °C for 8 h with polypropylene hydrophobic membrane, simulating heated AOMs contacted with membrane inside MD unit, to study the temperature effect on membrane fouling. The dissolved carbohydrate and protein in the sEPS and IOM + bEPS samples generally increased after being heated. Heating caused cell lysis and the release and dissolution of carbohydrate and protein from sEPS, IOM and bEPS into water. As heating temperature increased, the carbohydrate release from the AOM usually increased. The contact angle of membrane contacted with sEPS and IOM + bEPS reduced significantly after heat treatment. The reduction in IOM + bEPS was larger than sEPS, in line with SEM analysis, indicating membrane surfaces and pores with IOM + bEPS fouled more severely than sEPS. It is due to higher hydrophobicity in IOM + bEPS causing adherence to membrane and presence of amphiphiles. High protein, lipid, and saturated fats proportions also cause severe fouling. SEM-EDX analysis indicated presence of O, Na, Cl and Mg elements, pointing to carbohydrate and lipids, and salt trapped in foulants. AOM heating and composition had direct effect to the membrane integrity, dictating severity of fouling in MD operations.
Chilling restrains the distribution of mangroves. We tested whether foliar phosphorus (P) fractions and gene expression are associated with cold tolerance in mangrove species. We exposed seedlings of six mangrove populations from different latitudes to favorable, chilling and recovery treatments, and measured their foliar P concentrations and fractions, photochemistry, nighttime respiration, and gene expression. A Kandelia obovata (KO; 26.45°N) population completely and a Bruguiera gymnorhiza (Guangxi) (BGG; 21.50°N) population partially (30%) survived chilling. Avicennia marina (24.29°N), and other B. gymnorhiza (26.66°N, 24.40°N, and 19.62°N) populations died after chilling. Photosystems of KO and photosystem I of BGG were least injured. During chilling, leaf P fractions, except nucleic acid P in three populations, declined and photoinhibition and nighttime respiration increased in all populations, with the greatest impact in B. gymnorhiza. Leaf nucleic acid P was positively correlated with photochemical efficiency during recovery and nighttime respiration across populations for each treatment. Relatively high concentrations of nucleic acid P and metabolite P were associated with stronger chilling tolerance in KO. Bruguiera gymnorhiza exhibited relatively low concentrations of organic P in favorable and chilling conditions, but its partially survived population showed stronger compensation in nucleic acid P and Pi concentrations and gene expression during recovery.
It was found that the operational temperature and the incorporation of microbial fuel cell (MFC) into anaerobic membrane bioreactor (AnMBR) have significant effect on AnMBRs' filtration performance. This paper addresses two issues (i) effect of temperature on AnMBR; and (ii) effect of MFC on AnMBRs' performance. The highest COD removal efficiency was observed in mesophilic condition (45°C). It was observed that the bioreactors operated at 45°C had the highest filtration resistance compared to others, albeit the excellent performance in removing the organic pollutant. Next, MFC was combined with AnMBR where the MFC acted as a pre-treatment unit prior to AnMBR and it was fed directly with palm oil mill effluent (POME). The supernatant from MFC was further treated by AnMBR. Noticeable improvement in filtration performance was observed in the combined system. Decrease in polysaccharide amount was observed in combined system which in turn suggested that the better filtration performance.