Template-assisted growth is an important nanoelectrochemical deposition technique for synthesizing one-dimensional (1-D) nanostructures with uniformly well-controlled shapes and sizes. A good template with well-defined dimensions is imperative for realizing this task. Porous anodic alumina (PAA) has been a favorable candidate for this purpose as it can be tailor-made with precise pore geometries, such as pore length and diameter as well as inter-pore distances, via the anodisation of pure aluminium. This paper reports the fabrication of PAA templates and electrochemical synthesis of functional nanostructures in the form of nanowires using PAA templates as scaffolds. Axial heterostructured and homogeneous nanowires formed by engineering materials configuration via composition and/or layer thickness variations were fabricated for different functionalities. X-ray diffraction and imaging techniques were used to elucidate the microstructures, morphologies and chemical compositions of the nanowires produced. Due to their large surface area-to-volume ratios, and therefore high sensitivities, these functional nanostructures have useful applications as critical components in nanosensor devices and various areas of nanotechnology. Potential applications include as hydrogen gas sensors in nuclear power plant for monitoring structural integrity of reactor components and containment building, as well as environmental monitoring of air pollution and leakages of toxic gases and chemicals.
In this study, the numerical simulation in a mixing vessel agitated by a six bladed Rushton turbine has
been carried out to investigate the effects of effective parameters to the mixing process. The study is intended to screen the potential parameters which affect the optimization process and to provide the detail insights into the process. Three-dimensional and steady-state flow has been performed using the fully predictive Multiple Reference Frame (MRF) technique for the impeller and tank geometry. Process optimization is always used to ensure the optimum conditions are fulfilled to attain industries’ satisfaction or needs (ie; increase profit, low cost, yields, etc). In this study, the range of recommended speed to accelerate optimization is 100, 150 and 200rpm respectively and the range of recommended clearance is 50, 75 and 100mm respectively for dual Rushton impeller. Thus, the computer fluid dynamics (CFD) was introduced in order to screen the suitable parameters efficiently and to accelerate optimization. In this study,
Feasibility studies on the vitrification of spent ion exchange resins combined with glass cullet powder have been conducted using a High Temperature Test Furnace. Bottle glass cullet powder was used as matrix material to convert the ash of the spent resins into a glass. Vitrificat ion of spent ion exchange resins presents a reasonable disposal alternative, because of its inherent organic destruction capabilities, the volume reduction levels obtainable, and the durable product that it yields. In this study, the spent ion exchange resin from the PUSPATI TRIGA reactor of Nuclear Malaysia was combusted in a lab scale combustor and the resulting ash was vitrified together with glass cullet powder in a high temperature furnace to produce a stable spent resin ash embedded in glass. The factors affecting this immobilized waste, such as thermal stability, radiological stability and leachability have all been investigated. However, the outcome of these tests, which include the radionuclide activity concentration in the slag, the optimum conditioning temperature - in relation with volume reduction during vitrification - and the volume mixing ratio of matrix material were reported. It was found that the radionuclides present in spent resins were 54 Mn, 60 Co and 152Eu. The elementary chemical composition (carbon, hydrogen, nitrogen and sulphur) of spent resins was 27.6% C, 5.68% H, 2.04% N and 4.20% S, respectively. The maximum calorific value of spent resins was 1735 kJ/kg. The average activity concentrations of 54 Mn and 60Co in ash at 200oC were 9,411 ± 243 Bq/Kg and 12,637± 201 Bq/Kg. flue gases containing CO2, CO, SO2 and NO started to be emitted above 200oC. The optimum conditioning temperature was also the highest tested, i.e. 900oC in 45 minutes, and the best mixing ratio ash to matrix material was also the highest, ie 1:9. Finally, the leaching analysis of slag at 900oC in 45 minutes showed that the leaching activity of 60Co was below 0.5 Bq/mL.
Ground water contain natural radioactivity associated with uranium and thorium that present naturally in rocks and soils. Humans may be exposed to the emission of energetic alpha particle from supported radon decaying process in this water when it is inhaled or ingested. Assessment of supported radon in ground water was carried out using fourteen ground water samples from Cameron Highlands. The measurement was accomplished by degassing the water samples using pump and then allowing the gas to flow into specially constructed 0.0191 m8 metal chamber. The activity concentration of supported radon in water sample was measured using continuous radon monitor inside the radon chamber. Measurement was carried out at one hour interval for twenty four hours. The hourly supported radon concentration was found to stabilize after about 8 hours. The stabilized concentration was used to determine supported radon activity concentration in the water samples. Results of the study show that depending on the sampling location, the activity concentrations of supported radon are in the range from 0.09 - 0.48 Bq/L which is lower than the activity concentration of radon in drinking water as proposed by USEPA (11 Bq/L).
Thermoelectric nanostructures hold great promise for capturing and directly converting into electricity some vast amount of low-grade waste heats now being lost to the environment (e.g. from nuclear power plant, fossil fuel burning, automotives and household appliances). In this study, large-area vertically-aligned silicon nanowire (SiNW) arrays were synthesized in an aqueous solution containing AgN•i and HF on p-type Si (100) substrate by self-selective electroless etching process. The etching conditions were systematically varied in order to achieve different stages of nanowire formation. Diameters of the SiNWs obtained varied from approximately 50 to 200 nm and their lengths ranged from several to a few tens of um. Te/Bi2Tex.Si thermoelectric core-shell nanostructures were subsequently obtained via galvanic displacement of SiNWs in acidic HF electrolytes containing HTe02+ and 139' /HTe02+ ions. The reactions were basically a nano-electrochemical process due to the difference in redox potentials between the materials. The surface-modified SiNWs of core-shell structures had roughened surface morphologies and, therefore, higher surface-to-bulk ratios compared to unmodified SiNWs. They have potential applications in sensors, photovoltaic and thermoelectric nanodevices. Growth study on the SiNWs and core-shell nanostructures produced is presented using various microscopy, diffraction and probe-based techniques for microstructural, morphological and chemical characterizations.
UV curable coating formulation comprises urethane acrylate resin and nanosilica as filler were synthesized to develop UV curable inorganic organic hybrid composite (PUA). The surface of the nanosilica was chemically modified to improve its chemical interaction within the urethane acrylate matrix. The modification had been undertaken by applying vinyltrymetoxysilane (VTMOS) that acted as a coupling agent to produce organophilic silica shell (SIMA). The shell is linked to the silica via reaction with the surface silanol group of the silica. The disappearance of metoxy groups in VTMOS was demonstrated by FTIR spectrum. The percentage of silica particles in UV curable hybrid formulation were varied on 5%, 10%, 15%, 20% and 250% respectively. In this work, the formulation was applied on medium density fiber board (11/IDF) substrate and subsequent has been irradiated under UV light. Then, the coated MDF were characterized by several testing equipments (TGA, DSC, scratch tester, instron, SEM). From the result, we found that the addition of silica nanoparticles exhibit significant improvement in coating film properties as compared to film without silica nanoparticle includes significant improvement in its modulus and scratch resistance. This make them as promising coating candidate for MDF product. On the other hand, we also found that an increase of silica particle up to 25 wt%, the viscosity has increased rapidly indicates that it is not suitable for acrylate coating formulation due to disappearance of desired effect known as tixotrophy.
This article presents an upgraded LUDLUM Scaler Ratemeter Model 2200 into a nucleonic thickness and level gauge. A vertical pipe scanning, consisting mediums such as SS-316, sand, wax, polyethylene, oil, water and air (empty) was done at Malaysian Nuclear Agency, Bangi, Selangor in order to obtain a shielding data as well as the corresponding voltage signals at the ratemeter. A simple comparator circuit with reference potentiometers and LED indicators was then designed and fabricated to work as a thickness or level gauge. The reference can be adjusted in accordance to type and thickness of the pipe/ container, the source intensity of X or Gamma ray, diameter of the pipe and also the distance between source and the NaI(Tl) detector.
Triyttrium Pentairon (iii) Oxide (Y3Fe501,2) or familiar called as Yttrium Iron Garnet (YIG) is successfully prepared using a conventional mixed-oxide method of 5:3 Fe to Y ratios. YIG prepared from conventional mixed-oxide usually produced some associated phase which surely will affect electrical properties. In this study, various temperature used in the sintering process to induce associated phases (YIP) to be fully reacting to form single phase of YIG and the effect on resonance frequency is studied for resonator applications. The mixtures of oxide powders are calcined at 1100 "C and sintered at various temperatures of (1350, 1380, 1400, 1420 1450 QC, respectively). Cubic phase is detected from the formation of YIG. Some other phases such as YIP and hematite also present as secondary phase. However, it is seen that, based on the Rietvield refinement method, the total amount of secondary phase simulated are inversely proportional with sintering temperature. The powder was pressed into cylindrical pellet and tested as a microwave resonator in antenna application. It was found that, on the actual antenna circuit the operating frequencies measured are in the range of 10-12 GHz for all samples which suitable for X-band. At the end, overall radiation pattern for all samples exhibit an omnidirectional behavior.
Nuclear power is considered as one of the best option for future energy development in Malaysia. Since Malaysia has no experience in nuclear energy generation, commissioning the first nuclear power plant needs tremendous effort in various aspects. Site selection is one of important step in nuclear power plant commissioning process. This paper proposes candidate sites for nuclear power plant in Mersing, Kota Tinggi, Muar and Batu Pahat district in Johor, Malaysia. The candidate selection process uses the IAEA document and AELB guideline as main reference, supported by site selection procedure by various countries. Mapinfo Professional software was used to simulate the selection process for candidate areas for the nuclear power plant. This paper concluded that Tenygaroh and Jemaluang area are the most suitable area for nuclear power plant facilities in Johor, Malaysia.
CaCu3Ti4O12 (CCTO) has attracted a great attention for electronic devices miniaturization due to its
very high dielectric constant properties at a wide range of frequency and nearly constant over broad temperature range. The origins of the giant dielectric constant have been speculated from electrical heterogeneous of interior elements of the CCTO ceramics. Four origins were suggested contributed to the electrical heterogeneous. In this study heat treatment were done with the electrode contact in Argon gas environment and the electrical properties over very wide frequency of CCTO ceramics were investigated. Cylindrical CCTO pellets samples were prepared by solid state reaction method and single phase of XRD pattern was obtained after sintering processes. Electrical impedance responds were measured at frequency from 100 Hz to 1 GHz for the samples for untreated and heat treated at 200ºC, 250ºC, 300ºC, 350ºC and 400ºC of CCTO. Improvement to the dielectric constant can be seen for 350ºC and 400ºC samples and dielectric loss were improved for 200ºC and 300ºC samples for overall frequency. The variations were discussed based on oxygen deficiency content and resistivity of the elements inside of CCTO structure.
Even though EDXRF analysis has major advantages in the analysis of stainless steel samples such as simultaneous determination of the minor elements, analysis can be done without sample preparation and non-destructive analysis, the matrix issue arised from the inter element interaction can make the the final quantitative result to be in accurate. The paper relates a comparative quantitative analysis using standard and standardless methods in the determination of these elements. Standard method was done by plotting regression calibration graphs of the interested elements using BCS certified stainless steel standards. Different calibration plots were developed based on the available certified standards and these stainless steel grades include low alloy steel, austentic, ferritic and high speed. The standardless method on the other hand uses a mathematical modelling with matrix effect correction derived from Lucas-Tooth and Price model. Further
improvement on the accuracy of the standardless method was done by inclusion of pure elements into the development of the model. Discrepancy tests were then carried out for these quantitative methods on different certified samples and the results show that the high speed method is most reliable for determining of Ni and the standardless method for Mn.
An electronic database has been developed and implemented for ko-INAA method in Malaysia. Databases are often developed according to national requirements. This database contains constant nuclear data for ko-INAA method; Hogdahl-convention and Westcott-formalism as 3 separate command user interfaces. It has been created using Microsoft Access 2007 under a Windows operating system. This database saves time and the quality of results can be assured when the calculation of neutron flux parameters and concentration of elements by ko-INAA method are utilised. An evaluation of the database was conducted by IAEA Soil7 where the results published which showed a high level of consistency.
The thermal conductivity of boron carbide filled thermoplastic natural rubber blend composite is studied experimentally as a function of filler loading and filler size. A polymer blend of 60/40 NR/HDPE was used as matrix for incorporation of particulate nano- and micro-sized B4C as filler to form the composite. As the filler loading is increased from 2-10%wt, a reduction and increment of thermal conductivity was observed. The results show at lower filler loading, HDPE crystallinity affects the thermal conductivity up to 4 and 6%wt of filler for nano- and micro-composite respectively. Further increase the loading do not much alter the crystallinity as the filler is distributed in continues phase of NR. The increment of filler amount in the amorphous NR causes the thermal conductivity to gradually increase which indicates the formation of interconnecting filler network structures
The microstructure and mechanical properties of ceramic composites produced from alumina, yttria stabilized zirconia and chromia oxide system was investigated. The Cr2O3 weight percent was varied from 0 wt% to 1.0 wt%. Each batch of composition was mixed, uniaxially pressed to 13mm diameter and sintered at 1600 ◦C for 4 h in pressureless conditions. Studies on the effects of the sample microstructures on their mechanical and physical properties such as fracture toughness and bulk density were carried out. Results show that an addition of 0.6 wt% of Cr2O3 produces the best mechanical properties. Furthermore, microstructural observations show that the Al2O3 grain size is significantly dependent on the amount of Cr2O3 additives used. Maximum value obtained with 0.6 wt % Cr2O3 for the fracture toughness is 5.36 MPa.m1/2.
The corrosion behaviour of ternary aluminium alloy sacrificial anodes with small amount addition of tin as depassivating element in natural seawater was studied by means of conventional DC electrochemical measurements. Metallurgical microscope was employed in order to observe the changing of microstructure caused by tin present in ternary alloys. The relationship between microstructure and electrochemical results was examined and particular attention paid to the cause of the electrochemical efficiency of anode performance. The results indicate that the proper precipitates uniformly distributed of tin are influence on improving electrochemical performance of alumnium alloy anode.
The recognition of microcalcifications and masses from digital mammographic images are important to aid the detection of breast cancer. In this paper, we applied morphological techniques to extract the embedded structures from the images for subsequent analysis. A mammographic phantom was created with embedded structures such as micronodules, nodules and fibrils. For the preprocessing techniques, intensity transformation of gray scale was applied to the image. The structures of the image were enhanced and segmented using dilation for a morphological operation with morphological closing. Next, low pass Gaussian filter was applied to the image to smooth and reduce noises. It was found that our method improved the detection of microcalcifications and masses with high Peak Signal To Noise Ratio (PSNR).
This paper reviews the literature on uranium contamination and the removal of uranium from wastewater stemming from mining activities and nuclear power generation. After reviewing the applications of uranium in power generation, military, industry and scientific, this review discusses uranium and rare earth elements in wastewaters and the toxicity of uranium on aquatic life and humans. Further, various methods of removal of heavy metal contaminants including uranium are reviewed with special focus on the adsorption process and carbon nanotubes as a superior adsorbent.
The existence of Naturally Occurring Radioactive Materials (NORM) such as K-40 was studied all over the world for their characteristics and effects on human and environment. K-40 exist in the earth crust with the concentration about 1.8 mg/kg or 481 Bq/g.. In this study, the level of K-40 in soil samples were measured using gamma spectrometer equipped with hyper pure germanium detector. The samples were collected from an oil palm cultivated area of Jengka 15, in Maran District, Pahang. The results show the level of K-40 activities at various locations. The activities of K-40 are in the range 52.9-150.5 Bq/kg and total potassium concentrations are 1.60-4.50%. There are no correlation between activities of K-40 with elevation i.e. R2= 0.0885.
Neutron aperture is one of the collimator components in a neutron radiography facility. The optimum design of neutron aperture is very importance in order to obtain largest L/D ratio with highest thermal neutron flux and low gamma-rays at the image plane. In this study, the optimization of neutron aperture parameters were done using Monte Carlo N-Particle Transport Code, version five (MCNP5). This code has a capability to simulate the neutron, photon, and electron or coupled of neutron/photon/electron transport, including the capability to calculate eigen values for critical system. The aperture parameters concerned in this study are the selection of best aperture material, aperture thickness, aperture position and aperture center hole diameter. In these simulations, vacuum beam port medium was applied.
Even though a lot of new advanced materials have been developed nowadays, steel remains a major material in construction, automobiles, appliances, industrial machinery as well as in the nuclear industry. Due to steel easily corroded, a proper surface protection is required to avoid any failures and extended the life cycle of the components. Surface coating is an efficient and economical method to obtain desirable material surfaces properties. Hot dip aluminizing technique was utilized in this study. Experiments have been conducted on the mild steel substrates with 12mm diameter. Prior to hot dipping process, observation on grain growth at three different temperatures had also been conducted to understand the behaviour of steel under application of heat. The substrates were heated at 700ºC, 800ºC and 900ºC for 1 hour and the microstructure was analyzed. The temperature of 800C was chosen for hot dipping. The substrates were dipped into the molten aluminum maintained at temperature 800ºC for 2,4,6,8,10,15 and 20 minutes. Optical microscopy and energy dispersive X-ray spectroscopy were used in this investigation. From the microstructure observation, it showed the appearance of intermetallic layer covered by the top layer of Al on the mild steel substrate increased with the increase in dipping time ranging from 36 to 282μm. The result of EDX analysis revealed the existence of Fe and Al in form of Fe2Al5 phase for all the dipping time.