Displaying all 20 publications

Abstract:
Sort:
  1. Ibrahim MF, Hod R, Toha HR, Mohammed Nawi A, Idris IB, Mohd Yusoff H, et al.
    PMID: 33668186 DOI: 10.3390/ijerph18052221
    Poor management of hazardous waste can lead to environmental pollution, injuries, and adverse health risks. Children's exposure to hazardous waste may cause serious acute and chronic health problems due to their higher vulnerability to the toxic effects of chemicals. This study examines an incident of illegal chemical dumping in Pasir Gudang, Malaysia and its potential health impacts on children. The study introduced a risk assessment of possible health-related effects due to chemical contamination based on a real case scenario where quantification of the contamination was not feasible. A literature review and spatial analysis were used as research methods. On 6th March 2019, tons of hazardous waste were illegally disposed into Kim Kim River, Pasir Gudang, Malaysia. They were identified as benzene, acrolein, acrylonitrile, hydrogen chloride, methane, toluene, xylene, ethylbenzene, and d-limonene. As a result, 975 students in the vicinity developed signs and symptoms of respiratory disease due to the chemical poisoning. The findings of this study indicate that more effective policies and preventive actions are urgently needed to protect human health, especially children from improper hazardous waste management.
    Matched MeSH terms: Hazardous Waste; Hazardous Waste Sites*
  2. Hosseinzadeh-Bandbafha H, Li C, Chen X, Peng W, Aghbashlo M, Lam SS, et al.
    J Hazard Mater, 2022 02 15;424(Pt C):127636.
    PMID: 34740507 DOI: 10.1016/j.jhazmat.2021.127636
    Waste cooking oil (WCO) is a hazardous waste generated at staggering values globally. WCO disposal into various ecosystems, including soil and water, could result in severe environmental consequences. On the other hand, mismanagement of this hazardous waste could also be translated into the loss of resources given its energy content. Hence, finding cost-effective and eco-friendly alternative pathways for simultaneous management and valorization of WCO, such as conversion into biodiesel, has been widely sought. Due to its low toxicity, high biodegradability, renewability, and the possibility of direct use in diesel engines, biodiesel is a promising alternative to mineral diesel. However, the conventional homogeneous or heterogeneous catalysts used in the biodiesel production process, i.e., transesterification, are generally toxic and derived from non-renewable resources. Therefore, to boost the sustainability features of the process, the development of catalysts derived from renewable waste-oriented resources is of significant importance. In light of the above, the present work aims to review and critically discuss the hazardous WCO application for bioenergy production. Moreover, various waste-oriented catalysts used to valorize this waste are presented and discussed.
    Matched MeSH terms: Hazardous Waste*
  3. Ilankoon IMSK, Ghorbani Y, Chong MN, Herath G, Moyo T, Petersen J
    Waste Manag, 2018 Dec;82:258-275.
    PMID: 30509588 DOI: 10.1016/j.wasman.2018.10.018
    E-waste, or waste generated from electrical and electronic equipment, is considered as one of the fastest-growing waste categories, growing at a rate of 3-5% per year in the world. In 2016, 44.7 million tonnes of e-waste were generated in the world, which is equivalent to 6.1 kg for each person. E-waste is classified as a hazardous waste, but unlike other categories, e-waste also has significant potential for value recovery. As a result it is traded significantly between the developed and developing world, both as waste for disposal and as a resource for metal recovery. Only 20% of global e-waste in 2016 was properly recycled or disposed of, with the fate of the remaining 80% undocumented - likely to be dumped, traded or recycled under inferior conditions. This review paper provides an overview of the global e-waste resource and identifies the major challenges in the sector in terms of generation, global trade and waste management strategies. It lists the specific hazards associated with this type of waste that need to be taken into account in its management and includes a detailed overview of technologies employed or proposed for the recovery of value from e-waste. On the basis of this overview the paper identifies future directions for effective e-waste processing towards sustainable waste/resource management. It becomes clear that there is a strong divide between developed and developing countries with regard to this sector. While value recovery is practiced in centralised facilities employing advanced technologies in a highly regulated industrial environment in the developed world, in the developing world such recovery is practiced in a largely unregulated artisanal industry employing simplistic, labour intensive and environmentally hazardous approaches. Thus value is generated safely in the hi-tech environment of the developed world, whereas environmental burdens associated with exported waste and residual waste from simplistic processing remain largely in developing countries. It is argued that given the breadth of available technologies, a more systematic evaluation of the entire e-waste value chain needs to be conducted with a view to establishing integrated management of this resource (in terms of well-regulated value recovery and final residue disposal) at the appropriately local rather than global scale.
    Matched MeSH terms: Hazardous Waste
  4. Ranjbari M, Shams Esfandabadi Z, Shevchenko T, Chassagnon-Haned N, Peng W, Tabatabaei M, et al.
    J Hazard Mater, 2022 01 15;422:126724.
    PMID: 34399217 DOI: 10.1016/j.jhazmat.2021.126724
    Improper healthcare waste (HCW) management poses significant risks to the environment, human health, and socio-economic sustainability due to the infectious and hazardous nature of HCW. This research aims at rendering a comprehensive landscape of the body of research on HCW management by (i) mapping the scientific development of HCW research, (ii) identifying the prominent HCW research themes and trends, and (iii) providing a research agenda for HCW management towards a circular economy (CE) transition and sustainable environment. The analysis revealed four dominant HCW research themes: (1) HCW minimization, sustainable management, and policy-making; (2) HCW incineration and its associated environmental impacts; (3) hazardous HCW management practices; and (4) HCW handling and occupational safety and training. The results showed that the healthcare industry, despite its potential to contribute to the CE transition, has been overlooked in the CE discourse due to the single-use mindset of the healthcare industry in the wake of the infectious, toxic, and hazardous nature of HCW streams. The findings shed light on the HCW management domain by uncovering the current status of HCW research, highlighting the existing gaps and challenges, and providing potential avenues for further research towards a CE transition in the healthcare industry and HCW management.
    Matched MeSH terms: Hazardous Waste
  5. Low KS, Lee CK, Lee TS
    Bull Environ Contam Toxicol, 1996 Mar;56(3):405-12.
    PMID: 8825962
    Matched MeSH terms: Hazardous Waste
  6. Faiz I, Ahmad M, Ramadan MF, Zia U, Rozina, Bokhari A, et al.
    J Environ Manage, 2024 Jan 15;350:119567.
    PMID: 38007927 DOI: 10.1016/j.jenvman.2023.119567
    Dealing with the current defaults of environmental toxicity, heating, waste management, and economic crises, exploration of novel non-edible, toxic, and waste feedstock for renewable biodiesel synthesis is the need of the hour. The present study is concerned with Buxus papillosa with seeds oil concentration (45% w/w), a promising biodiesel feedstock encountering environmental defaults and waste management; in addition, this research performed simulation based-response surface methodology (RSM) for Buxus papillosa bio-diesel. Synthesis and application of novel Phyto-nanocatalyst bimetallic oxide with Buxus papillosa fruit capsule aqueous extract was advantageous during transesterification. Characterization of sodium/potassium oxide Phyto-nanocatalyst confirmed 23.5 nm nano-size and enhanced catalytic activity. Other characterizing tools are FTIR, DRS, XRD, Zeta potential, SEM, and EDX. Methyl ester formation was authenticated by FTIR, GC-MS, and NMR. A maximum 97% yield was obtained at optimized conditions i.e., methanol ratio to oil (8:1), catalyst amount (0.37 wt%), reaction duration (180 min), and temperature of 80 °C. The reusability of novel sodium/potassium oxide was checked for six reactions. Buxus papillosa fuel properties were within the international restrictions of fuel. The sulphur content of 0.00090% signified the environmental remedial nature of Buxus papillosa methyl esters and it is a highly recommendable species for biodiesel production at large scale due to a t huge number of seeds production and vast distribution.
    Matched MeSH terms: Hazardous Waste
  7. Mokhtar MB, Murad W
    J Environ Health, 2010 Apr;72(8):24-9.
    PMID: 20420051
    Environmental health problems in Malaysia are mostly attributed to atmospheric pollution, water pollution, climate change, ozone depletion, and solid waste management, as well as toxic, chemical, and hazardous waste management. The Ministry of Health, Malaysia, has been vigorously pursuing the environmental health agenda by collaborating with other agencies at district, state, national, and international levels. This article discusses the issues and management framework of environmental health in Malaysia. Some issues requiring further investigation in order to clearly understand the trade-off between atmospheric change and environmental health are suggested. These suggestions are developed with particular reference to appraisals concerned with the development and implementation of environmental policy, programs, and practice. Research on the relevant issues is discussed and a framework is built involving a comprehensive review of the literature and existing framework of Malaysian environmental health.
    Matched MeSH terms: Hazardous Waste/prevention & control
  8. Pariatamby A, Subramaniam C, Mizutani S, Takatsuki H
    Environ Sci, 2006;13(5):289-96.
    PMID: 17096003
    Fly ash samples from a mixed hazardous waste (MHW) incinerator were subjected to solidification and stabilization (S/S) studies using ordinary Portland cement (OPC) as the binder. Additives (i.e., activated carbon and rice husk) were also homogenized with the binder and waste to determine the effectiveness of the immobilization of heavy metals. The toxicity characteristics leaching procedure (TCLP), Japanese Leaching Test (JLT-13) and the American Nuclear Test 16.1 (modified) ANS 16.1 were used to gauge the leaching of heavy metals from the solidified matrixes. Compressibility strength of the solidified matrixes was also tested using the American Standard Testing Material (ASTM) test procedure for the compressive strength of hydraulic cement mortars.
    Matched MeSH terms: Hazardous Waste*
  9. Low KS, Lee CK, Lee CY
    Appl Biochem Biotechnol, 2001 Jan;90(1):75-87.
    PMID: 11257809
    The potential of quaternized wood (QW) chips in removing hexavalent chromium from synthetic solution and chrome waste under both batch and continuous-flow conditions was investigated. Sorption was found to be dependent on pH, metal concentration, and temperature. QW chips provide higher sorption capacity and wider pH range compared with untreated wood chips. The equilibrium data could be fitted into the Langmuir isotherm model, and maximum sorption capacities were calculated to be 27.03 and 25.77 mg/g in synthetic chromate solution and chrome waste, respectively. The presence of sulfate in high concentration appeared to suppress the uptake of chromium by QW chips. Column studies showed that bed depth influenced the breakthrough time greatly whereas flow rate of influent had little effect on its sorption on the column.
    Matched MeSH terms: Hazardous Waste*
  10. Ibrahim RK, Hayyan M, AlSaadi MA, Hayyan A, Ibrahim S
    Environ Sci Pollut Res Int, 2016 Jul;23(14):13754-88.
    PMID: 27074929 DOI: 10.1007/s11356-016-6457-z
    Global deterioration of water, soil, and atmosphere by the release of toxic chemicals from the ongoing anthropogenic activities is becoming a serious problem throughout the world. This poses numerous issues relevant to ecosystem and human health that intensify the application challenges of conventional treatment technologies. Therefore, this review sheds the light on the recent progresses in nanotechnology and its vital role to encompass the imperative demand to monitor and treat the emerging hazardous wastes with lower cost, less energy, as well as higher efficiency. Essentially, the key aspects of this account are to briefly outline the advantages of nanotechnology over conventional treatment technologies and to relevantly highlight the treatment applications of some nanomaterials (e.g., carbon-based nanoparticles, antibacterial nanoparticles, and metal oxide nanoparticles) in the following environments: (1) air (treatment of greenhouse gases, volatile organic compounds, and bioaerosols via adsorption, photocatalytic degradation, thermal decomposition, and air filtration processes), (2) soil (application of nanomaterials as amendment agents for phytoremediation processes and utilization of stabilizers to enhance their performance), and (3) water (removal of organic pollutants, heavy metals, pathogens through adsorption, membrane processes, photocatalysis, and disinfection processes).
    Matched MeSH terms: Hazardous Waste/analysis*
  11. Yadav VK, Yadav KK, Alam J, Cabral-Pinto MM, Gnanamoorthy G, Alhoshan M, et al.
    Environ Sci Pollut Res Int, 2023 Jun;30(28):71766-71778.
    PMID: 34523099 DOI: 10.1007/s11356-021-15009-8
    Incense sticks ash is one of the most unexplored by-products generated at religious places and houses obtained after the combustion of incense sticks. Every year, tonnes of incense sticks ash is produced at religious places in India which are disposed of into the rivers and water bodies. The presence of heavy metals and high content of alkali metals challenges a potential threat to the living organism after the disposal in the river. The leaching of heavy metals and alkali metals may lead to water pollution. Besides this, incense sticks also have a high amount of calcium, silica, alumina, and ferrous along with traces of rutile and other oxides either in crystalline or amorphous phases. The incense sticks ash, heavy metals, and alkali metals can be extracted by water, mineral acids, and alkali. Ferrous can be extracted by magnetic separation, while calcium by HCl, alumina by sulfuric acid treatment, and silica by strong hydroxides like NaOH. The recovery of such elements by using acids and bases will eliminate their toxic heavy metals at the same time recovering major value-added minerals from it. Here, in the present research work, the effect on the elemental composition, morphology, crystallinity, and size of incense sticks ash particles was observed by extracting ferrous, followed by extraction of calcium by HCl and alumina by H2SO4 at 90-95 °C for 90 min. The final residue was treated with 4 M NaOH, in order to extract leachable silica at 90 °C for 90 min along with continuous stirring. The transformation of various minerals phases and microstructures of incense sticks ash (ISA) and other residues during ferrous, extraction, calcium, and alumina and silica extraction was studied using Fourier transform infrared (FTIR), dynamic light scattering (DLS), X-ray fluorescence (XRF), X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and inductively coupled plasma-optical emission spectroscopy (ICP-OES). DLS was used for analyzing the size during the experiments while FTIR helped in the confirmation of the formation of new products during the treatments. From the various instrumental analyses, it was found that the toxic metals present in the initial incense sticks ash got eliminated. Besides this, the major alkali metals, i.e., Ca and Mg, got reduced during these successive treatments. Initially, there were mainly irregular shaped, micron-sized particles that were dominant in the incense sticks ash particles. Besides this, there were plenty of carbon particles left unburned during combustion. In the final residue, nanosized flowers shaped along with cuboidal micron-sized particles were dominant. present in If, such sequential techniques will be applied by the industries based on recycling of incense sticks ash, then not only the solid waste pollution will be reduced but also numerous value-added minerals like ferrous, silica, alumina calcium oxides and carbonates can be recovered from such waste. The value-added minerals could act as an economical and sustainable source of adsorbent for wastewater treatment in future.
    Matched MeSH terms: Hazardous Waste/analysis
  12. Beddu S, Abd Manan TSB, Zainoodin MM, Khan T, Wan Mohtar WHM, Nurika O, et al.
    Data Brief, 2020 Aug;31:105843.
    PMID: 32596432 DOI: 10.1016/j.dib.2020.105843
    Coal combustion by-products (CCPs) (i.e. fly (FA) and bottom (BA) ashes) generated by power plants contain heavy metals. This research presents leaching properties of coal ashes (FA and BA) collected from Jimah coal-fired power station, Port Dickson, Negeri Sembilan using USEPA standard methods namely toxicity characteristic leaching procedure (TCLP), and synthetic precipitation leaching procedure (SPLP). Heavy metals like lead (Pb), zinc (Zn), copper (Cu) and arsenic (As) were quantified using atomic absorption spectrometer (AAS). The leached of heavy metals fluxes were Cu < Zn < Pb < As. As leached the most whilst indicating of possible contamination from As. Overall, the ranges of leached concentration were adhered to permissible limits of hazardous waste criteria for metal (Pb and As) and industrial effluent (Zn and Cu). The presented data has potential reuse as reference for the coal ash concrete mixed design application in construction industries.
    Matched MeSH terms: Hazardous Waste
  13. Nosheen F, Malik N, Mehmood Z, Jabeen F, Mahmood A, Ibrahim M, et al.
    Environ Res, 2022 Dec;215(Pt 2):114240.
    PMID: 36103930 DOI: 10.1016/j.envres.2022.114240
    Biomedical waste from healthcare activities poses a higher hazard of infection and damage than other types of trash. The main objective of the study was to assess the awareness knowledge and practices of biomedical waste management (BMWM) among health care professionals in the health care units. The cross-sectional study was carried out to access the awareness, knowledge and practices of health care professionals for BMWM. Using a qualitative approach, the study was escorted in two Apex hospitals i.e. the Allied Hospital and the District Head Quarter Hospital, Faisalabad, Pakistan from August 5, 2019 to October 15, 2019. More than 90% of respondents knew the phrase BMWM, but just 35.4% had awareness about biomedical waste regulations. About 71.6% of the respondents were familiar with biomedical waste's color-coding segregation. The study concludes gap in the awareness, knowledge and practices for BMWM. The sanitary workers of the hospitals had no knowledge about BMWM and the BMWM/healthcare waste management rule 2005 established in Pakistan due to the lack of training regarding waste management and the segregation process. Some of the staff members were aware of the BMWM practices under the rules and regulations of Pakistan but were unable to implement at their work place. It is necessary to dispose of the biomedical waste according to the established terms and conditions of BMWM rules (2005) of Pakistan. Weak structure of BMWM was observed at the study sites due to the lack of training, liabilities and absence of penalties against improper biomedical waste disposal as violation of the rules and regulations. It's a dire need of the time to consider the biomedical waste as hazardous waste and make policies for its safe disposal and ensure the implementation of the policies in all the medical centers of Pakistan.
    Matched MeSH terms: Hazardous Waste
  14. Tanabe S, Kunisue T
    Environ Pollut, 2007 Mar;146(2):400-13.
    PMID: 16949712
    In this paper, we concisely reviewed the contamination of persistent organic pollutants (POPs) such as polychlorinated dibenzo-p-dioxins (PCDDs), dibenzofurans (PCDFs), biphenyls (PCBs), dichlorodiphenyltrichloroethane and its metabolites (DDTs), hexachlorocyclohexane isomers (HCHs), chlordane compounds (CHLs), hexachlorobenzene (HCB) in human breast milk collected from Asian countries such as Japan, China, Philippines, Vietnam, Cambodia, India, Malaysia, and Indonesia during 1999-2003. Dioxins, PCBs, CHLs in Japanese, and DDTs in Vietnamese, Chinese, Cambodian, Malaysian, and HCHs in Chinese, Indian, and HCB in Chinese breast milk were predominant. In India, levels of dioxins and related compounds (DRCs) in the mothers living around the open dumping site were notably higher than those from the reference site and other Asian developing countries, indicating that significant pollution sources of DRCs are present in the dumping site of India and the residents there have been exposed to relatively higher levels of these contaminants possibly via bovine milk.
    Matched MeSH terms: Hazardous Waste/analysis
  15. Hasan UA, Mohd Hairon S, Yaacob NM, Daud A, Abdul Hamid A, Hassan N, et al.
    PMID: 31514391 DOI: 10.3390/ijerph16183356
    Background: Structured education is needed to cultivate safe sharp disposal behavior among diabetic patients. Thus, this study aimed to assess the effectiveness of the Diabetes Community Sharp Disposal Education Module in improving knowledge and sharp disposal practice among Malaysian Type 2 diabetic patients. Methods: This quasi-experimental study was conducted at primary health clinics in two districts in Kelantan, a state in the North-East Region of Peninsular Malaysia. A total of 132 Type 2 diabetic patients on insulin therapy were involved, with 68 participants in each control and intervention group. The health education intervention was based on the validated Diabetes Community Sharp Disposal Education Module. The knowledge and practices were measured using a validated questionnaire at baseline, one month, and three months after the intervention. Results: There was a significant increment in the mean knowledge score for intervention group; from baseline to one month follow up and from baseline to three months follow up [Greenhouse-Geisser; F(1.5, 199.7) = 62.38, p < 0.001; effect size (η2) = 0.318]. Intervention group had significantly higher mean knowledge score as compared to control group; at one month and three months follow up [F(1, 134) = 17.38, p < 0.001; effect size (η2) = 0.115]. There was a statistically significant increment in the proportion of participants in the intervention group who practiced the proper community sharp disposal method over time, X2(2) = 52.061, p < 0.001. Conclusions: The Diabetes Community Sharp Disposal Education Module was an effective health education tool to improve knowledge and encourage Malaysian diabetic patients to engage with proper sharp disposal practices.
    Matched MeSH terms: Hazardous Waste*
  16. Low KS, Lee CK, Ow-Wee ST
    Bull Environ Contam Toxicol, 1995 Aug;55(2):270-5.
    PMID: 7579934
    Matched MeSH terms: Hazardous Waste
  17. Chew KW, Chia SR, Chia WY, Cheah WY, Munawaroh HSH, Ong WJ
    Environ Pollut, 2021 Mar 01;278:116836.
    PMID: 33689952 DOI: 10.1016/j.envpol.2021.116836
    The remarkable journey of progression of mankind has created various impacts in the form of polluted environment, amassed heavy metals and depleting resources. This alarming situation demands sustainable energy resources and approaches to deal with these environmental hazards and power deficit. Pyrolysis and co-pyrolysis address both energy and environmental issues caused by civilization and industrialization. The processes use hazardous waste materials including waste tires, plastic and medical waste, and biomass waste such as livestock waste and agricultural waste as feedstock to produce gas, char and pyrolysis oil for energy production. Usage of hazardous materials as pyrolysis and co-pyrolysis feedstock reduces disposal of harmful substances into environment, reducing occurrence of soil and water pollution, and substituting the non-renewable feedstock, fossil fuels. As compared to combustion, pyrolysis and co-pyrolysis have less emission of air pollutants and act as alternative options to landfill disposal and incineration for hazardous materials and biomass waste. Hence, stabilizing heavy metals and solving the energy and waste management problems. This review discusses the pyrolysis and co-pyrolysis of biomass and harmful wastes to strive towards circular economy and eco-friendly, cleaner energy with minimum waste disposal, reducing negative impact on the planet and creating future possibilities.
    Matched MeSH terms: Hazardous Waste
  18. Ghaffari Khaligh N, Mihankhah T, Titinchi S, Shahnavaz Z, Rafie Johan M
    Turk J Chem, 2020;44(4):1100-1109.
    PMID: 33488215 DOI: 10.3906/kim-2005-6
    This work introduces a new additive named 4,4'-trimethylenedipiperidine for the practical and ecofriendly preparation of ethyl 5-amino-7-(4-phenyl)-4,7-dihydro-[1,2,4]triazolo[1,5-a]pyrimidine-6-carboxylate derivatives. This chemical is commercially available and easy to handle. It also possesses a low melting point and a broad liquid range temperature, high thermal stability, and good solubility in water. Based on green chemistry principles, the reaction was performed in a) a mixture of green solvents i.e. water and ethanol (1:1 v/v) at reflux temperature, and b) the additive was liquefied at 65 °C and the reaction was conducted in the liquid state of the additive. High yields of the desired triazolo-pyrimidines were obtained under both aforementioned conditions. Our results demonstrated that this additive, containing 2 Lewis base sites and able to act as an acceptor-donor hydrogen bonding group, is a novel and efficient alternative to piperidine, owing to its unique properties such as its reduced toxicity, nonflammable nature, nonvolatile state, broad liquid range temperature, high thermal stability, and ability to be safely handled. Furthermore, this additive could be completely recovered and exhibited high recyclability without any change in its chemical structure and no significant reduction in its activity. The current methodology has several advantages: (a) it avoids the use of hazardous materials, as well as toxic, volatile, and flammable solvents, (b) it does not entail tedious processes, harsh conditions, and the multistep preparation of catalysts, (c) it uses a metal-free and noncorrosive catalyst, and (d) reduces the generation of hazardous waste and simple work-up processes. The most important result of this study is that 4,4'-trimethylenedipiperidine can be a promising alternative for toxic, volatile, and flammable base reagents in organic synthesis owing to its unique properties.
    Matched MeSH terms: Hazardous Waste
  19. Mulimani P
    Br Dent J, 2017 Jun 23;222(12):954-961.
    PMID: 28642517 DOI: 10.1038/sj.bdj.2017.546
    Dentistry is highly energy and resource intensive with significant environmental impact. Factors inherent in the profession such as enormous electricity demands of electronic dental equipment, voluminous water requirements, environmental effects of biomaterials (before, during and after clinical use), the use of radiation and the generation of hazardous waste involving mercury, lead etc have contributed towards this. With rising temperatures across the world due to global warming, efforts are being made worldwide to mitigate the effects of environmental damage by resorting to sustainability concepts and green solutions in a myriad of ways. In such a scenario, a professional obligation and social responsibility of dentists makes it imperative to transform the practice of dentistry from a hazardous to a sustainable one, by adopting environmental-friendly measures or 'green dentistry'. The NHS in the UK has been proactive in implementing sustainability in healthcare by setting targets, developing guidance papers, initiating steering groups to develop measures and implementing actions through its Sustainable Development Unit (SDU). Such sustainable frameworks, specific to dentistry, are not yet available and even the scientific literature is devoid of studies in this field although anecdotal narratives abound. Hence this paper attempts to present a comprehensive evaluation of the existing healthcare sustainability principles, for their parallel application in the field of dentistry and lays out a blueprint for integrating the two main underlying principles of sustainability - resource use efficiency and eliminating or minimising pollution - in the day-to-day practice. The article also highlights the importance of social values, community care, engaging stakeholders, economic benefits, developing policy and providing leadership in converting the concept of green dentistry into a practised reality.
    Matched MeSH terms: Hazardous Waste
  20. Murugan K, Suresh U, Panneerselvam C, Rajaganesh R, Roni M, Aziz AT, et al.
    Environ Sci Pollut Res Int, 2018 Apr;25(11):10456-10470.
    PMID: 28913784 DOI: 10.1007/s11356-017-0074-3
    The development of novel mosquito control tools is a key prerequisite to build effective and reliable Integrated Vector Management strategies. Here, we proposed a novel method using cigarette butts for the synthesis of Ag nanostructures toxic to young instars of the malaria vector Anopheles stephensi, chloroquine (CQ)-resistant malaria parasites Plasmodium falciparum and microbial pathogens. The non-target impact of these nanomaterials in the aquatic environment was evaluated testing them at sub-lethal doses on the predatory copepod Mesocyclops aspericornis. Cigarette butt-synthesized Ag nanostructures were characterized by UV-vis and FTIR spectroscopy, as well as by EDX, SEM and XRD analyses. Low doses of cigarette butt extracts (with and without tobacco) showed larvicidal and pupicidal toxicity on An. stephensi. The LC50 of cigarette butt-synthesized Ag nanostructures ranged from 4.505 ppm (I instar larvae) to 8.070 ppm (pupae) using smoked cigarette butts with tobacco, and from 3.571 (I instar larvae) to 6.143 ppm (pupae) using unsmoked cigarette butts without tobacco. Smoke toxicity experiments conducted against adults showed that unsmoked cigarette butts-based coils led to mortality comparable to permethrin-based positive control (84.2 and 91.2%, respectively). A single treatment with cigarette butts extracts and Ag nanostructures significantly reduced egg hatchability of An. stephensi. Furthermore, the antiplasmodial activity of cigarette butt extracts (with and without tobacco) and synthesized Ag nanostructures was evaluated against CQ-resistant (CQ-r) and CQ-sensitive (CQ-s) strains of P. falciparum. The lowest IC50 values were achieved by cigarette butt extracts without tobacco, they were 54.63 μg/ml (CQ-s) and 63.26 μg/ml (CQ-r); while Ag nanostructure IC50 values were 72.13 μg/ml (CQ-s) and 77.33 μg/ml (CQ-r). In MIC assays, low doses of the Ag nanostructures inhibited the growth of Bacillus subtilis, Klebsiella pneumoniae and Salmonella typhi. Finally, the predation efficiency of copepod M. aspericornis towards larvae of An. stephensi did not decrease in a nanoparticle-contaminated environment, if compared to control predation assays. Overall, the present research would suggest that an abundant hazardous waste, such as cigarette butts, can be turned to an important resource for nanosynthesis of highly effective antiplasmodials and insecticides.
    Matched MeSH terms: Hazardous Waste
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links