Work ability is related to many factors that might influence one's capacity to work. This study aimed to examine the work ability and its related factors among small and medium enterprises (SME) workers in 4 Association of Southeast Asian Nations (ASEAN) countries. The participants in this study included 2098 workers from food and textile industries in Indonesia, Malaysia, Thailand, and Vietnam. A cross-sectional survey of anonymous self-administrated questionnaire was designed to collect information on sociodemographic factors, work environment and ergonomic condition, musculoskeletal disorders, and work ability. Bivariate correlation coefficient and multiple linear regression analyses were used to predict the work ability. Results of this study confirm that work ability in 4 ASEAN countries was similar to that in European countries, and that the sociodemographic factors, work environment and ergonomic condition, and musculoskeletal disorder (MSD) were associated with work ability. These factors are important for considering occupational health and safety policy to promote work ability in food, textile, and other SME workers.
Microplastic fibers from textiles have been known to significantly contribute to marine microplastic pollution. However, little is known about the microfiber formation and discharge during textile production. In this study, we have quantified microfiber emissions from one large and representative textile factory during different stages, spanning seven different materials, including cotton, polyester, and blended fabrics, to further guide control strategies. Wet-processing steps released up to 25 times more microfibers than home laundering, with dyeing contributing to 95.0% of the total emissions. Microfiber release could be reduced by using white coloring, a lower dyeing temperature, and a shorter dyeing duration. Thinner, denser yarns increased microfiber pollution, whereas using tightly twisted fibers mitigated release. Globally, wet textile processing potentially produced 6.4 kt of microfibers in 2020, with China, India, and the US as significant contributors. The study underlined the environmental impact of textile production and the need for mitigation strategies, particularly in dyeing processes and fiber choice. In addition, no significant difference was observed between the virgin polyesters and the used ones. Replacing virgin fibers with recycled fibers in polyester fabrics, due to their increasing consumption, might offer another potential solution. The findings highlighted the substantial impact of textile production on microfiber released into the environment, and optimization of material selection, knitting technologies, production processing, and recycled materials could be effective mitigation strategies.
Layered double hydroxide of Mg-Al-carbonate system (MACH) was prepared and its heat-treated product (MACHT) was obtained by calcination at 500 degrees C. The resulting materials were used as an adsorbent for removal of color from synthetic textile wastewater (STW) and textile wastewater (TWW). Batch kinetic study showed that these materials are an efficient adsorbent for textile dye. The maximum adsorption capacities between 16 to 32 mg of dyes per g of adsorbent was obtained by fitting the adsorption data to the Langmuir adsorption Isotherm. It was found that the adsorption capacity of MACHT is higher than MACH.
White-rot fungi, namely Coriolus versicolor and Schizophyllum commune, were studied for the biodecolorization of textile dyeing effluent in shaker-flask experiments. The results showed that C. versicolor was able to achieve 68% color removal after 5 days of treatment while that of S. commune was 88% in 9 days. Both fungi achieved the above results in non-sterile condition with diammonium hydrogen phosphate as the nutrient supplement. On the other hand, the best COD removal of 80% was obtained with C. versicolor in 9 days in sterile effluent with yeast extract as nutrient supplement, while S. commune was able to remove 85% COD within 8 days in non-sterile textile effluent supplemented with diammonium hydrogen phosphate.
The physical characteristics, microbial activities and kinetic properties of the granular sludge biomass were investigated under the influence of different hydraulic retention times (HRT) along with the performance of the system in removal of color and COD of synthetic textile wastewater. The study was conducted in a column reactor operated according to a sequential batch reactor with a sequence of anaerobic and aerobic reaction phases. Six stages of different HRTs and different anaerobic and aerobic reaction time were evaluated. It was observed that the increase in HRT resulted in the reduction of organic loading rate (OLR). This has caused a decrease in biomass concentration (MLSS), reduction in mean size of the granules, lowered the settling ability of the granules and reduction of oxygen uptake rate (OUR), overall specific biomass growth rate (ìoverall), endogeneous decay rate (kd) and biomass yield (Yobs, Y). When the OLR was increased by adding carbon sources (glucose, sodium acetate and ethanol), there was a slight increase in the MLSS, the granules mean size, ìoverall, and biomass yield. Under high HRT, increasing the anaerobic to aerobic reaction time ratio caused an increase in the concentration of MLSS, mean size of granules and lowered the SVI value and biomass yield. The ìoverall and biomass yield increased with the reduction in anaerobic/aerobic time ratio. The HRT of 24 h with anaerobic and aerobic reaction time of 17.8 and 5.8 h respectively appear to be the best cycle operation of SBR. Under these conditions, not only the physical properties of the biogranules have improved, the highest removal of color (i.e. 94.1±0.6%) and organics (i.e. 86.5±0.5%) of the synthetic textile dyeing wastewater have been achieved.
Wastewater from industrial plants such as textile, electroplating and petroleum refineries contains various substances that tend to increase the chemical oxygen demand (COD) of the wastewater. Therefore, it is desired to develop a process suitable for treating the wastewater to meet the regulatory limits. This work was conducted to investigate the potential of adapted single culture of A. baumannii, A.calcoaceticus and C.cellulans in reducing COD in real textile wastewater. The study was carried out by adapting each single culture (10% inoculums) to increasing concentration (1%, 2.5 %, 5%, 7.5 % and 10%) of textile wastewater. Then it was introduced to the textile effluent without pH adjustment for five days and the COD values were measured. The textile wastewater was supplemented with pineapple waste for bacterial growth and metabolism. Results obtained showed that pineapple waste was a good nutrient supply for the growth of the bacteria and the best concentration of textile wastewater for adaptation was at 2.5%. The results also showed that A.calcoaceticus shows highest COD reduction with 67% removal whereas A. baumannii and C.cellulans with 60% and 58% removal respectively. The outcome supported that the single culture used in this study showed considerably high reduction of COD from real textile wastewater.
Effluent containing colour/dyes, especially reactive dyes, becomes a great concern of wastewater treatment because it is toxic to human life and aquatic life. In this study, reactive dye of Black B was separated using the supported liquid membrane process. Commercial polypropylene membrane was used as a support of the kerosene-tridodecylamine liquid membrane. Several parameters were tested and the result showed that almost 100% of 70 ppm Black B was removed and 99% of 70 ppm Black B was recovered at pH 2 of the feed phase containing 0.00001 M Na2SiO3, flow rate of 150 ml/min and 0.2 M NaOH. The membrane support also remained stable for up to 36 hours under an optimum condition.
Dyes are known to be a causative agent of occupational asthma exposed to them. We evaluate respiratory symptoms among textile. The study population comprised 106 exposed workers and control (unexposed) group. Data were collected by a questionnaire. Pulmonary Function Tests (PFTs) were performed. Among the exposed workers 36.8% defined phlegm. Respiratory symptoms were not significantly different between two groups. The employment duration of the exposed workers with phlegm was longer than those without phlegm (p = 0.027). The mean % predicted of forced expiratory flow (FEF) 25-75 of the exposed workers was found to be significantly lower than the control (unexposed) group (p = 0.01). Our study suggests that textile dyeing might cause respiratory symptoms at workers.
The textile industry consumes a large volume of organic dyes and water. These organic dyes, which remained in the effluents, are usually persistent and difficult to degrade by conventional wastewater treatment techniques. If the wastewater is not treated properly and is discharged into water system, it will cause environmental pollution and risk to living organisms. To mitigate these impacts, the photo-driven catalysis process using semiconductor materials emerges as a promising approach. The semiconductor photocatalysts are able to remove the organic effluent through their mineralization and decolorization abilities. Besides the commonly used titanium dioxide (TiO2), manganese dioxide (MnO2) is a potential photocatalyst for wastewater treatment. MnO2 has a narrow bandgap energy of 1~2 eV. Thus, it possesses high possibility to be driven by visible light and infrared light for dye degradation. This paper reviews the MnO2-based photocatalysts in various aspects, including its fundamental and photocatalytic mechanisms, recent progress in the synthesis of MnO2 nanostructures in particle forms and on supporting systems, and regeneration of photocatalysts for repeated use. In addition, the effect of various factors that could affect the photocatalytic performance of MnO2 nanostructures are discussed, followed by the future prospects of the development of this semiconductor photocatalysts towards commercialization.
This study was to develop biogranules using a sequencing batch reactor (SBR) and to evaluate the effect of pineapple wastewater (PW) as a co-substrate for treating real textile wastewater (RTW). The biogranular system cycle was 24 h (2 stages of phase), with an anaerobic phase (17.8 h) followed by an aerobic phase (5.8 h) for every stage of the phase. The concentration of pineapple wastewater was the main factor studied in influencing COD and color removal efficiency. Pineapple wastewater with different concentrations (7, 5, 4, 3, and 0% v/v) makes a total volume of 3 L and causes the OLRs to vary from 2.90 to 0.23 kg COD/m3day. The system achieved 55% of average color removal and 88% of average COD removal at 7%v/v PW concentration during treatment. With the addition of PW, the removal increased significantly. The experiment on the treatment of RTW without any added nutrients proved the importance of co-substrate in dye degradation.
This research aims to evaluate the performance of PolyCera® Titan membrane for different wastewater treatment. Membrane filtration of several cycles was conducted in understanding the fouling mechanism, fouling propensity, and defouling potential of the PolyCera® Titan which had not been studied by any other researcher before. The PolyCera® Titan membrane is effective for the treatment of textile industry wastewater, palm oil mill effluent (POME), leachate, and semiconductor-industry wastewater. Rejection of methylene blue (MB) and Congo red (CR) was in the range of 78.76-86.04% and 88.89-93.71%, respectively; 94.72-96.50% NaCl, 96.07-97.62% kaolin, and 97.26-97.73% glucose were rejected from synthetic leachate indicating the removal of TDS, TSS, and COD from the leachate, respectively. Standard blocking and complete model were the best models used to explain the PolyCera® Titan membrane fouling mechanism in all types of wastewater treatment processes with a high R2 value. Physical cleaning with the use of distilled water was able to recover the permeate flux with the flux recovery ratio (FRR) value in the range of 79.2-95.22% in the first cycle, 81.20-98.16% in the second cycle, and 86.09-95.96% in the third cycle.
OBJECTIVES: Lung exposures including cigarette smoking and silica exposure are associated with the risk of rheumatoid arthritis (RA). We investigated the association between textile dust exposure and the risk of RA in the Malaysian population, with a focus on women who rarely smoke.
METHODS: Data from the Malaysian Epidemiological Investigation of Rheumatoid Arthritis population-based case-control study involving 910 female early RA cases and 910 female age-matched controls were analysed. Self-reported information on ever/never occupationally exposed to textile dust was used to estimate the risk of developing anti-citrullinated protein antibody (ACPA)-positive and ACPA-negative RA. Interaction between textile dust and the human leucocyte antigen DR β-1 (HLA-DRB1) shared epitope (SE) was evaluated by calculating the attributable proportion due to interaction (AP), with 95% CI.
RESULTS: Occupational exposure to textile dust was significantly associated with an increased risk of developing RA in the Malaysian female population (OR 2.8, 95% CI 1.6 to 5.2). The association between occupational exposure to textile dust and risk of RA was uniformly observed for the ACPA-positive RA (OR 2.5, 95% CI 1.3 to 4.8) and ACPA-negative RA (OR 3.5, 95% CI 1.7 to 7.0) subsets, respectively. We observed a significant interaction between exposure to occupational textile dust and HLA-DRB1 SE alleles regarding the risk of ACPA-positive RA (OR for double exposed: 39.1, 95% CI 5.1 to 297.5; AP: 0.8, 95% CI 0.5 to 1.2).
CONCLUSIONS: This is the first study demonstrating that textile dust exposure is associated with an increased risk for RA. In addition, a gene-environment interaction between HLA-DRB1 SE and textile dust exposure provides a high risk for ACPA-positive RA.
A micro-mesoporous activated carbon (AC) was produced via an innovative approach combining microwave pyrolysis and chemical activation using NaOH/KOH mixture. The pyrolysis was examined over different chemical impregnation ratio, microwave power, microwave irradiation time and types of activating agents for the yield, chemical composition, and porous characteristic of the AC obtained. The AC was then tested for its feasibility as textile dye adsorbent. About 29 wt% yield of AC was obtained from the banana peel with low ash and moisture (<5 wt%), and showed a micro-mesoporous structure with high BET surface area (≤1038 m2/g) and pore volume (≤0.80 cm3/g), indicating that it can be utilized as adsorbent to remove dye. Up to 90% adsorption of malachite green dye was achieved by the AC. Our results indicate that the microwave-activation approach represents a promising attempt to produce good quality AC for dye adsorption.
Methyl orange is one of the anionic dyes and is a major pollutant from textile industry that enters both aquatic and atmospheric systems. In this research, methyl orange was degraded using TiO2 powder and immobilized TiO2 on glass. Titanium tetra-isopropoxide (TTIP) was used for preparation of TiO2 powder using soft chemistry method, and it was immobilized on glass via paste-gel coating method. The prepared photocatalysts were characterized by XRD and SEM. Highly crystalline anatase TiO2 powder photocatalyst was obtained. Meanwhile, immobilized TiO2 was less crystalline and agglomerated onto the glass surface. TiO2 powder had higher degradation rate (71%) compared to immobilized TiO2 (52%) due to its chemical stability and larger amount of photocatalyst contacted with methyl orange during the degradation process.
In Malaysia, most colored wastewater from dyeing factories is discharged to the environment causing serious problems. In this paper the influence of several reacting conditions, i.e. H2O2, pH, Ultraviolet (UV) intensity and dye concentration, on the performance of the immobilized system is discussed. The pH of the solution was varied from 3 to 11 while H2O2 concentration tested was from 10(-4) M to 5 x 10(-2) M. UV was tested at 365 nm and 254 nm, while dye concentration ranged from 2.5 x 10(-4) M to 10(-3) M. The influence of the reacting conditions was assessed based on absorbance. Using an OG concentration of 10(-3) M, the degradation increases from 17.8% to 49.7%. Optimum concentration of H2O2 was found to be 5 x 10(-3) M for degradation. Increasing the intensity of the UV light via shorter light wavelength also improves the performance of the system. Increasing the concentration of the dye reduces the overall performance of the system. Using the dye concentration of 2.5 x 10(-4) M (H2O2 = 10(-2) M, lambda = 254 nm, pH = 11), gives a degradation of 93.2%. At dye concentration of 10(-3) M, the performance was reduced to 53.1%.
Industrial wastewater minimization can be conducted using four main strategies: (i) reuse; (ii) regeneration-reuse; (iii) regeneration-recycling; and (iv) process changes. This study is concerned with (i) and (ii) to investigate the most suitable approach to wastewater minimization for an old textile industry plant. A systematic water networks design using water pinch analysis (WPA) was developed to minimize the water usage and wastewater generation for the textile plant. COD was chosen as the main parameter. An integrated design method has been applied, which brings the engineering insight using WPA that can determine the minimum flowrate of the water usage and then minimize the water consumption and wastewater generation as well. The overall result of this study shows that WPA has been effectively applied using both reuse and regeneration-reuse strategies for the old textile industry plant, and reduced the operating cost by 16% and 50% respectively.
Textile wastewater contains methylene blue (MB), a major coloring agent in textile industry. Activated carbon (AC) is the most widely used adsorbent in removing dyes from industrial wastewater. However, high production cost of AC is the major obstacle for its wide application in dye wastewater treatment. In this study, a sustainable approach in synthesizing graphenic adsorbent from palm oil mill effluent (POME), a potential carbonaceous source, has been explored. This new development in adsorption technique is considered as green synthesis as it does not require any binder during the synthesis process, and at the same time, it helps to solve the bottleneck of palm oil industry as POME is the main cause contributed to Malaysia's water pollution problem. The synthesized GSC was characterized through XRD, FESEM, and EDX. The adsorption performance of the synthesized GSC was evaluated by adsorption of MB. The effect of initial concentration of synthetic MB solution (1-20 mg/L) and weight of GSC (5-20 g) were investigated. A remarkable change in color of synthetic MB solution from blue to crystal clear was observed at the end of adsorption study. High efficiency of the synthesized GSC for dye-contaminated wastewater treatment is concluded.
Liquid-liquid extraction (LLE) of methylene blue (MB) from industrial wastewater using benzoic acid (extractant) in xylene has been studied at 27 degrees C. The extraction of the dye increased with increasing extractant concentration. The extraction abilities have been studied on benzoic acid concentration in the range of 0.36-5.8x10(-2) M. The distribution ratio of the dye is reasonably high (D=49.5) even in the presence of inorganic salts. Irrespective of the concentration of dye, extraction under optimal conditions was 90-99% after 15 min of phase separation. The extracted dye in the organic phase can be back extracted into sulphuric acid solution. The resultant recovered organic phase can be reused in succeeding extraction of dye with the yield ranging from 99 to 87% after 15 times reused, depending on the concentration of the initial feed solution. Experimental parameters examined were benzoic acid concentration, effect of diluent, effect of pH, effect of initial dye concentration, effect of equilibration time, various stripping agents, aqueous to organic phase ratio in extraction, organic to aqueous phase ratio in stripping and reusability of solvent.
Wastewater treatment is a key challenge in the textile industry. The current treatment methods for textile wastewater are insufficient or ineffective for complex dyes generated from the textile industry. This study evaluated the performances of two novel inorganic coagulants with high cationic charges, namely, titanium tetrachloride (TiCl4) and zirconium tetrachloride (ZrCl4). They were utilised to treat textile industry wastewater. Both coagulation processes were performed under the same experimental operational conditions. Turbidity, suspended solids (SS), colour, chemical oxygen demand (COD) and ammonia were measured to assess the efficiencies of the coagulants. Results indicated that ZrCl4 and TiCl4 exhibited high potentials for textile wastewater treatment. ZrCl4 presented high removal efficiency in COD and SS, whereas TiCl4 showed excellent removal in ammonia.
This study deals with the use of activated carbon prepared from bamboo waste (BMAC), as an adsorbent for the removal of chemical oxygen demand (COD) and color of cotton textile mill wastewater. Bamboo waste was used to prepare activated carbon by chemical activation using phosphoric acid (H(3)PO(4)) as chemical agent. The effects of three preparation variables activation temperature, activation time and H(3)PO(4):precursor (wt%) impregnation ratio on the color and COD removal were investigated. Based on the central composite design (CCD) and quadratic models were developed to correlate the preparation variables to the color and COD. From the analysis of variance (ANOVA), the most influential factor on each experimental design response was identified. The optimum condition was obtained by using temperature of 556 degrees C, activation time of 2.33 h and chemical impregnation ratio of 5.24, which resulted in 93.08% of color and 73.98% of COD.