New technologies rely on the development of new materials, and these may simply be the innovative combination of known components. The structural combination of a polymer hydrogel network with a nanoparticle (metals, non-metals, metal oxides, and polymeric moieties) holds the promise of providing superior functionality to the composite material with applications in diverse fields, including catalysis, electronics, bio-sensing, drug delivery, nano-medicine, and environmental remediation. This mixing may result in a synergistic property enhancement of each component: for example, the mechanical strength of the hydrogel and concomitantly decrease aggregation of the nanoparticles. These mutual benefits and the associated potential applications have seen a surge of interest in the past decade from multi-disciplinary research groups. Recent advances in nanoparticle-hydrogel composites are herein reviewed with a focus on their synthesis, design, potential applications, and the inherent challenges accompanying these exciting materials.
Glycerol electro-oxidation offers a green route to produce the high value added chemicals. Here in, we report the glycerol electro-oxidation over a series of multi walled carbon nano tubes supported monometallic (Pt/CNT and Pd/CNT) and bimetallic (Pt-Pd/CNT) catalysts in alkaline medium. The cyclic voltammetry, linear sweep voltammetry and chronoamperometry measurements were used to evaluate the activity and stability of the catalysts. The Pt-Pd/CNT electrocatalyst exhibited the highest activity in terms of higher current density (129.25 A/m²) and electrochemical surface area (382 m²/g). The glycerol electro-oxidation products formed at a potential of 0.013 V were analyzed systematically by high performance liquid chromatography. Overall, six compounds were found including mesoxalic acid, 1,3-dihydroxyacetone, glyceraldehyde, glyceric acid, tartronic acid and oxalic acid. A highest mesoxalic acid selectivity of 86.42% was obtained for Pt-Pd/CNT catalyst while a maximum tartronic acid selectivity of 50.17% and 46.02% was achieved for Pd/CNT and Pt/CNT respectively. It was found that the introduction of Pd into Pt/CNT lattice facilitated the formation of C3 products in terms of maximum selectivity achieved (86.42%) while the monometallic catalysts (Pd/CNT and Pt/CNT) showed a poor performance in comparison to their counterpart.
Photocatalysts provide excellent potential for the full removal of organic chemical pollutants as an environmentally friendly technology. It has been noted that under UV-visible light irradiation, nanostructured semiconductor metal oxides photocatalysts can degrade different organic pollutants. The Sn6SiO8/rGO nanocomposite was synthesized by a hydrothermal method. The Sn6SiO8 nanoparticles hexagonal phase was confirmed by XRD and functional groups were analyzed by FT-IR spectroscopy. The bandgap of Sn6SiO8 nanoparticles (NPs) and Sn6SiO8/GO composites were found to be 2.7 eV and 2.5 eV, respectively. SEM images of samples showed that the flakes like morphology. This Sn6SiO8/rGO nanocomposite was testing for photocatalytic dye degradation of MG under visible light illumination and excellent response for the catalysts. The enhancement of photocatalytic performance was mainly attributed to the increased light absorption, charge separation efficiency and specific surface area, proved by UV-vis DRS. Further, the radical trapping experiments revealed that holes (h+) and superoxide radicals (·O-₂) were the main active species for the degradation of MG, and a possible photocatalytic mechanism was discussed.
Herein, we report the synthesis of SnO, Cu₂O and SnO-Cu₂O mixed oxide thin films on fluorinedoped tin oxide (FTO) substrate by Aerosol-Assisted Chemical Vapour Deposition (AACVD) process using [Cu (dmae)₂(H₂O)] and [Sn (dmae) (OAc)]₂ as molecular precursors for SnO and Cu₂O, respectively at 400 °C. The X-ray diffraction (XRD) pattern can be ascribed to the tetragonal phase of SnO crystals with space group P4 and cubic phase of Cu₂O crystals with space group Pn- 3m/nmm, respectively. The surface morphology characteristics of SnO, Cu₂O and SnO-Cu₂Omixed oxide have been investigated using Field Emission Scanning Electron Microscope (FESEM) which revealed that the SnO was grown homogeneously in cubical shape while Cu₂O possess nano balls shaped morphologies. The UV band gap values of SnO-Cu₂O mixed oxide thin film was found to be 2.6 eV appropriate for photoelectrochemical (PEC) applications. The synthesized material was proposed for PEC applications and has shown enhanced catalytic performance in the presence of light.
We found that the gold nanoparticles with high-density and crystalline-shape, such as nanocubes, nanobricks, pentahedral nanorods, etc., can be realized on the surface by using a seed-mediated growth method with a unique seeding process, namely alcohothermal. By using a conventional growth solution that contains HAuCl4, cetyltrimethylammonium bromide, NaOH and ascorbic acid, gold nanoparticles with crystalline-morphology (gold nanocrystals) of yield up to ca. 95%, can be prepared. An alcohothermal seeding was carried out by a thermal reduction of gold ions from an alcoholic solution of gold salt on the surface through an annealing process at a moderate temperature, namely 250 degrees C. It is believed that the unique initial characteristic (presumably the structures) of the gold nanoseeds particles as the result of peculiar nanoseeds formation process, prepared using this approach, instead of a simple thermal restructuring of the as prepared nanoseeds as confirmed by the results of annealing treatment on the nanoseed prepared using the normal and in-situ reduction seeding, was as the driving factor for the projected growth of crystalline-shape gold nanoparticles on the surface. The crystalline-shape gold nanoparticles modified-surface should find a potential application in catalysis, sensors and SERS.
Herein we reported the effect of doping and addition of surfactant on SnO2 nanostructures for enhanced photocatalytic activity. Pristine SnO2, Zn-SnO2 and SDS-(Zn-SnO2) was prepared via simple co-precipitation method and the product was annealed at 600 °C to obtain a clear phase. The structural, optical, vibrational, morphological characteristics of the synthesized SnO2, Zn-SnO2 and SDS-(Zn-SnO2) product were investigated. SnO2, Zn-SnO2 and SDS-(Zn-SnO2) possess crystallite size of 20 nm, 19 nm and 18 nm correspondingly with tetragonal structure and high purity. The metal oxygen vibrations were present in FT-IR spectra. The obtained bandgap energies of SnO2, Zn-SnO2 and SDS-(Zn-SnO2) were 3.58 eV, 3.51 eV and 2.81 eV due to the effect of dopant and surfactant. This narrowing of bandgap helped in the photocatalytic activity. The morphology of the pristine sample showed poor growth of nanostructures with high level of agglomeration which was effectively reduced for other two samples. Product photocatalytic action was tested beneath visible light of 300 W. SDS-(Zn-SnO2) nanostructure efficiency showed 90% degradation of RhB dye which is 2.5 times higher than pristine sample. Narrow bandgap, crystallite size, better growth of nanostructures paved the way for SDS-(Zn-SnO2) to degrade the toxic pollutant. The superior performance and individuality of SDS-(Zn-SnO2) will makes it a potential competitor on reducing toxic pollutants from wastewater in future research.
This study aimed to analyze the environmental impacts of the oxidative desulfurization (ODS) process catalyzed by metal-free reduced graphene oxide (rGO) through life cycle assessment (LCA). The environmental impacts study containing the rGO production process, the ODS process, the comparison of different oxidants and solvents was developed. This study was performed by using ReCiPe 2016 V1.03 Hierarchist midpoint as well as endpoint approach and SimaPro software. For the production of 1 kg rGO, the results showed that hydrochloric acid (washing), sulfuric acid (mixing), hydrazine (reduction) and electricity were four main contributors in this process, and this process showed a significant impact on human health 14.21 Pt followed by ecosystem 0.845 Pt and resources 0.164 Pt. For the production of 1 kg desulfurized oil (400 ppm), main environmental impacts were terrestrial ecotoxicity (43.256 kg 1,4-DCB), global warming (41.058 kg CO2), human non-carcinogenic toxicity (19.570 kg 1,4-DCB) and fossil resource scarcity (13.178 kg oil), and the main contributors were electricity, diesel oil and acetonitrile. The whole ODS process also showed a greatest effect on human health. For two common oxidants hydrogen peroxide and oxygen used in ODS, hydrogen peroxide showed a greater impact than oxygen. On the other hand, for three common solvents employed in ODS, N-methyl-2-pyrrolidone had a more serious impact on human health followed by acetonitrile and N,N-dimethylformamide. As such, LCA results demonstrated the detailed environmental impacts originated from the catalytic ODS, hence elucidating systematic guidance for its future development toward practicality.
Transition metals play an important role in the growth of carbon nanotubes (CNTs). Series of unsupported hybrid catalysts consisting of Ni:Cu, Ni:Cr, and Ni:Mn doped with Nd catalyst, respectively were synthesized by impregnation method. The catalytic performance of the catalyst for the production of CNTs was measured in the pyrolysis process of hydrocarbon source by catalytic chemical vapour deposition method. Acetylene gas was used as the source of carbon in the pyrolysis process. The decomposition of acetylene was carried out at 700ºC. The bulk properties of the catalysts were investigated by X-ray diffraction. Field emission scanning electron microscopy and thermal analysis were used to observe the morphology and thermal stability of the as-synthesized CNTs, respectively. Hybrid catalyst of Ni:Mn/Nd and Ni:Cr/Nd in 3:1 atomic ratio gave high percentage of carbon yield which was assigned for the high production of CNTs with the mass of yield 18 times greater than the initial mass of the catalyst used.
Solvent flow reactor system was introduced into the extraction system to increase the system efficiency and enhance the extraction yield by adding fresh solvent during the extraction processes. The liquefaction experiment was carried out at various flow-rates (1, 3 and 5 ml/min), reaction times (30, 45 and 60 min) and reaction temperatures (300ºC, 350ºC, 400ºC, 420ºC and 450ºC) with tetralin as solvent. Despite the ability of adding fresh solvent into the extraction process, the conversion of oil+gas was still considered to be low as there was ~25% of coal extracts left to be converted into low molecular weight compounds. One possible option to increase the oil yield is by applying catalyst that will further break up the coal extracts into small molecular weight compounds. In this study, a second reactor was introduced consisting of catalyst (NiSiO2) assuming that the catalyst would interact more effectively with coal extracts rather than the coal itself. In the
absence of catalyst, the oil yield was 55%. By introducing the Ni catalyst, the oil yield increased by 15%. Further analysis of GCMS showed that the oil from catalytic liquefaction gave out more low molecular weight compounds in comparison to the un-catalytic liquefaction oil.
The present investigation deals with the development of ethanol-vapour-sensing materials coated with the semiconducting oxide TiO2. Thick films of anatase TiO2 were deposited using the sol-gel dip-coating technique on alumina substrates by conventional alkoxide sol and modified sol added with Degussa P-25 as the sensing medium. It was shown that crystallised TiO2 anatase was obtained at the annealing temperature of 500oC. The fabricated TiO2 sensors exhibited highest sensitivity at the sensing temperature of 350 ºC. Sensitivity towards the ethanol vapour was further increased with UV light effect. The enhancement of the sensitivity of the modified catalytic pellet can be explained by the crystallite of anatase TiO2 and the effect of the photocatalytic of TiO2. The high sensitivity of the TiO2 film deposited with modified sol revealed that the modified sol could be a new alternative in the development of a TiO2 ethanol sensor.
Xylitol is a high value sugar alcohol with anticariogenic properties that is used as an ideal sweetener for diabetic patients. Industrially, xylitol is manufactured by catalytic reduction of pure xylose, which has
some disadvantages. The fermentation process has been studied as an alternative, but its viability is dependent on the optimization of several variables. This fermentation process on an industrial-scale is not feasible due to decreased productivity. Compared to the fermentation process, enzymatic method is expected to make a substantial increase in productivity. Enzymatic xylitol production from xylose exist in lignocellulosics is an attractive and promising alternative method to the chemical process. The enzymatic method might be able to overcome the disadvantages of the chemical process. This article reviews the literature on the processes for xylitol production and identifies further ways for improved xylitol production to compete with the current chemical process.
In this work, an activated electric arc furnace slag (A-EAFS) was investigated as an effective Fenton catalyst for the photodegradation of methylene blue (MB) and acid blue 29 (AB29). Fourier transform infrared spectroscopy and UV-visible absorption analyses indicated that A-EAFS offers additional Fe3O4 because of the changes in the iron oxide phase and the favorable response to visible light. It has been found that the highest degradation efficiency can reach up to 94% for MB under optimal conditions of 1 g L-1 of A-EAFS, 20 mM H2O2, and pH 3. The optimal conditions for AB29 were 0.1 g L-1 A-EAFS, 4 mM H2O2, and pH 3 to reach 98% degradation efficiency. Visible light enhanced the degradation of both dyes. In addition, A-EAFS, could be easily separated magnetically, exhibited good chemical stability after seven successive photodegradation cycles.
Malaysia is currently poised to introduce its Science, Technology and Innovation (STI) Policy and Act to bolster the nation's efforts at economic and social transformation. In championing this initiative, the Academy of Sciences Malaysia, while continuing to advise the Government on STI issues of the day, has made major strides in taking stock of the country's STI strengths in the various sectors of the economy as well as weaknesses that need to be addressed in terms of human capital development. In this article, the author examines the level of research expertise presently in the country in the field of chemistry, and elaborates on the four key areas of energy, catalysis and chemical synthesis, materials science and biological chemistry which will be researched globally in the next few decades that we would also need to be engaged upon to remain competitive. Intended for a wider audience than chemists alone, the descriptive sections in the article by and large belie an interdisciplinary flavour. The article also advocates the need for a more thorough road mapping exercise of the STI efforts in chemistry across the spectrum of academia and industry and makes some recommendations towards forging strong collaborations in research between the universities, public research institutes and the industry which are seen as vital in providing cross-cutting chemical solutions throughout the value chains and to the success of technologies identified as critical to the nation.
Ordered microporous NaY zeolite and mesoporous copper oxide are high performance material as catalysts and adsorbents. The copper oxide-NaY zeolite modification in combination of their physicochemical properties could provide excellent opportunities for the creation of new gas adsorbents. In this study, modified NaY zeolite properties and methane adsorptive characteristics were investigated by dispersing copper oxide onto the NaY zeolite structure using the thermal dispersion method. The structures of the copper oxide modified zeolites were characterized by powder X-ray diffraction and Micromeritics ASAP 2000, while the methane adsorption characteristics were analyzed using a thermogravimetric analyzer. The results revealed that types of copper oxide, copper oxide loading concentration, calcination temperature and calcination time greatly affected the modified zeolite structure and gas methane adsorption characteristics.
Silica-alumina catalyst was prepared and used in the catalytic fast pyrolysis of durian rind in a drop-type two-stage reactor. The effects of catalytic temperature (400 °C-600 °C) and catalyst-to-durian rind ratio (1:30-3:30) were evaluated. Bio-oil yield was increased with increased catalytic temperature due to considerable dehydration process, but it was reduced with high catalyst loading due to the overcracking of organics into light gases. Silica-alumina catalyst possessed good selectivity and the products changed according to the temperature. The major components in bio-oil were hydrocarbons, furan derivatives, and aromatic compounds at 400 °C, 500 °C, and 600 °C, respectively. The hydrogen and carbon contents of bio-oil were reduced with high catalyst loading due to the overcracking of organics, and the deoxygenation process became unfavorable. The silica-alumina catalyst worked well in catalytic fast pyrolysis of durian rind, and the condition may be adjusted based on the desired products.
Advanced oxidation process involves production of hydroxyl radical for industrial wastewater treatment. This method is based on the irradiation of UV light to photocatalysts such as TiO2 and ZnO for photodegradation of pollutant. UV light is used for irradiation in photocatalytic process because TiO2 has a high band gap energy which is around 3.2 eV. There can be shift adsorption to visible light by reducing the band gap energy to below 3.2 eV. Doped catalyst is one of the means to reduce band gap energy. Different methods are used for doped catalyst which uses transition metals and titanium dioxide. The band gap energy of three types of transition metals Fe, Cd and Co after being doped with TiO2, are around 2.88 ev, 2.97ev and 2.96 ev, respectively which are all below TiO2 energy. Some of the transition metals change the energy level to below 3.2 eV and the adsorption shifts to visible light for degradation of industrial pollutant after being doped with titanium dioxide. This paper aims at providing a deep insight into advanced oxidation processes, photocatalysts and their applications in wastewater treatment, doping processes and the effects of operational factors on photocatalytic degradation.
The copper-catalyzed azide-alkyne cycloaddition (CuAAC) reaction has proven to be a pivotal advance in chemical ligation strategies with applications ranging from polymer fabrication to bioconjugation. However, application in vivo has been limited by the inherent toxicity of the copper catalyst. Herein, we report the application of heterogeneous copper catalysts in azide-alkyne cycloaddition processes in biological systems ranging from cells to zebrafish, with reactions spanning from fluorophore activation to the first reported in situ generation of a triazole-containing anticancer agent from two benign components, opening up many new avenues of exploration for CuAAC chemistry.
Automobile exhaust emission control is one of the trending issues in automobile research field. It caused by high
pollution such as carbon monoxide (CO), nitrogen oxides (NOx), and hydrocarbons (HC) distributed by automobile
especially form diesel engine. These pollutants give a harmful effect to the environment and human health. Therefore,
this paper proposed in reviewing methods on fabrication of modified catalytic converter. FeCrAl is used as substrate
which treated using ultrasonic bath technique which could improve the exhaust emission control. This metallic catalytic converter used as the replacement of precious metal that have high production cost.
Enzymatic catalysis is considered to be among the most environmental friendly processes for the synthesis of fine chemicals. In this study, lipase from Thermomyces lanuginosus (Lecitase Ultra™) was used to catalyze the synthesis of flavor esters, i.e., methyl butanoate and methyl benzoate by esterification of the acids with methanol in a microfluidic system. Maximum reaction rates of 195 and 115 mM min(-1) corresponding to catalytic efficiencies (k cat/K M) of 0.30 and 0.24 min(-1) mM(-1) as well as yield conversion of 54 and 41 % were observed in methyl butanoate and methyl benzoate synthesis, respectively. Catalytic turnover (k cat) was higher for methyl butanoate synthesis. Rate of synthesis and yield decreased with increasing flow rates. For both esters, increase in microfluidic flow rate resulted in increased advective transport over molecular diffusion and reaction rate, thus lower conversion. In microfluidic synthesis using T. lanuginosus lipase, the following reaction conditions were 40 °C, flow rate 0.1 mL min(-1), and 123 U g(-1) enzyme loading found to be the optimum operating limits. The work demonstrated the application of enzyme(s) in a microreactor system for the synthesis of industrially important esters.
Co-pyrolysis of biomass with abundantly available materials could be an economical method for production of bio-fuels. However, elimination of oxygenated compounds poses a considerable challenge. Catalytic co-pyrolysis is another potential technique for upgrading bio-oils for application as liquid fuels in standard engines. This technique promotes the production of high-quality bio-oil through acid catalyzed reduction of oxygenated compounds and mutagenic polyaromatic hydrocarbons. This work aims to review and summarize research progress on co-pyrolysis and catalytic co-pyrolysis, as well as their benefits on enhancement of bio-oils derived from biomass. This review focuses on the potential of plastic wastes and coal materials as co-feed in co-pyrolysis to produce valuable liquid fuel. This paper also proposes future directions for using this technique to obtain high yields of bio-oils.