This article reports a degradation study that was done on stent prototypes made of biodegradable Fe35Mn alloy in a simulated human coronary arterial condition. The stent degradation was observed for a short-term period from 0.5 to 168 h, which simulates the early period of stenting procedure. Potentiodynamic polarization and electrochemical impedance spectroscopy were used to quantify degradation rate and surface property of the stents. Results showed that signs of degradation were visible on both crimped and expanded stents after 1 h of test, mostly located on the stent's curvatures. The degradation rate of stent was higher compared to that of the original alloy, indicating the surface altering effect of stent fabrication processing to degradation. A single oxide layer was formed and detected as a porous structure with capacitive behavior. Expanded stents exhibited lower polarization resistance compared to the nonexpanded ones, indicating the cold work effect of expansion procedure to degradation.
In order to achieve better treatment for local wounds and bacterial infections, topical formulations containing Cocos nucifera Linn. were developed. These formulations were evaluated for their physicochemical properties and antimicrobial efficacy against various strains of microorganisms. Semisolid formulations containing 5% w/w of Cocos nucifera Linn. were prepared by employing different dermatological bases and were evaluated for their physical appearance, pH, rheological properties, FTIR-spectroscopic analysis, thermodynamic stability and stability studies. The antimicrobial activity of each prepared formulation was determined using disk-diffusion method against various strains of microorganisms. All the prepared formulations were found to be stable and exhibited suitable physicochemical characteristics including pH, viscosity and spreadability which are necessary for an ideal topical preparation, in addition to strong antimicrobial activity. Carbopol gel base was found to be the most suitable dermatological base for Cocos nucifera Linn. in comparsion to other bases. Cocos nucifera Linn. formulations showed great potential for wounds and local bacterial infections. Moreover, carbopol gel base with its aesthetic appeal was found to be a suitable dermatological base for Cocos nucifera Linn. semisolid formulation as it had demonstrated significant physicochemical properties and greater diffusion when assessed using disk- diffusion method.
Topical emulsions stabilized with non-ionic emulsifiers have been an attractive alternative as vehicles for drug delivery, particularly for the patients suffering from dermatological problems. Haruan (a natural wound healer) creams were formulated with different types of emulsifiers (Tween 80 and Span 80) using different grades of Malaysian Palm-oleins (DFPL 56, 60, 62 and 65). The stability (at room temperature and accelerated stability testing) of the various creams was evaluated at different temperatures (5, 25 and 45 degrees C) for a period of 6 months by measuring changes in droplet size, viscosity and percentage oil separation. The emulsifier type and concentration showed pronounced effect on the physicochemical properties of the cream, whereas storage time did not. This study suggested that the choice of emulsifiers and concentration of haruan extract are the most important factors in the stability of the haruan creams.
A study was conducted to evaluate the cross flow tubular ultrafiltration behavior of aqueous solutions of pectin. The effectiveness of pulsatile flow as a cleaning-in-place (CIP) technique to improve permeate flux was undertaken on the above mentioned solution. This investigation is part of a study to apply membrane filtration in the clarification of tropical fruit juice. The main variables, which were investigated, include the concentration of pectin, pulse frequency and amplitude. It was found that the amount of pectin in the solution significantly affects its ultrafiltration behavior. From the observed profiles, it is evident that the formation of gel layer on the membrane surface is responsible for the leveling of flux at high pressures. The presence of pectin was found to affect the properties of the solution such as viscosity, pH and the size of pectin colloid. Improvements in the permeate flux for pectin solution were obtained by employing pulsatile flow cleaning-in-place technique. Both pulse frequency and amplitude are important parameters that can improve the improvement of in-situ cleaning method. Similar to several findings reported in the literature, pulsatile flow showed significant effectiveness of about 60% higher flux when the ultrafiltration process is operated under laminar condition.
Injectable hydrogel with multifunctional tunable properties comprising biocompatibility, anti-oxidative, anti-bacterial, and/or anti-infection are highly preferred to efficiently promote diabetic wound repair and its development remains a challenge. In this study, we report hyaluronic acid and Pullulan-based injectable hydrogel loaded with curcumin that could potentiate reepithelization, increase angiogenesis, and collagen deposition at wound microenvironment to endorse healing cascade compared to other treatment groups. The physical interaction and self-assembly of hyaluronic acid-Pullulan-grafted-pluronic F127 injectable hydrogel were confirmed using nuclear magnetic resonance (1H NMR) and Fourier transformed infrared spectroscopy (FT-IR), and cytocompatibility was confirmed by fibroblast viability assay. The CUR-laden hyaluronic acid-Pullulan-g-F127 injectable hydrogel promptly undergoes a sol-gel transition and has proved to potentiate wound healing in a streptozotocin-induced diabetic rat model by promoting 93% of wound closure compared to other groups having 35%, 38%, and 62%. The comparative in vivo study and histological examination was conducted which demonstrated an expeditious recovery rate by significantly reducing the wound healing days i.e. 35 days in a control group, 33 days in the CUR suspension group, 21 days in unloaded injectable, and 13 days was observed in CUR loaded hydrogel group. Furthermore, we suggest that the injectable hydrogel laden with CUR showed a prompt wound healing potential by increasing the cell proliferation and serves as a drug delivery platform for sustained and targeted delivery of hydrophobic moieties.
Starch and hydrocolloids were often used together in food industry to modify the rheological properties with the aim to enhance the starch tolerance to processing conditions. As such, the rheological properties of xanthan gum (XG), carrageenan, high (HMP) and low methoxyl pectin (LMP), with native corn starch (NCS) and modified corn starch (MCS) at different temperature were evaluated in this study. The flow behavior index (n) of corn starch-hydrocolloid mixtures were observed in the range from 0.160 to 0.604 where indicated the shear thinning behavior. The addition of hydrocolloids increased the apparent viscosity of the starch system. NCS mixtures showed consistency index (K) and apparent viscosities (na,100) decreased with increase in the temperature. The addition of XG and carrageenan increased the storage (G’) and loss (G”) moduli. Among the hydrocolloids, the XG addition to the NCS exhibited superior viscoelastic properties as evidenced by the highest G’ and lowest tan δ values. XG was observed capable to increase while pectin reduced the solid-like starch system. This result provides pragmatic data for food engineer in process design and food product development by minimizing the cost of trial and error.
Present study compared the rheological properties of glutinous rice flour (GRF) gel (33.3%, w/v) added with raw bee honey (RBH) or stingless bee honey (SBH) with/without heating treatment. RBH (diatase activity: 12.14 Schade) and SBH (1.53 Schade) significantly reduced the network of GRF gel by lowering the gel viscosity, with RBH having the highest rate of viscosity decrease (- 2.74 × 10-5 Pa). As the addition of heated-SBH or heated-RBH did not reduce gel viscosity, it was hypothesised that active diastase played a major role to weaken gel network. This was further supported by the significant and the lowest storage modulus (G') value of RBH-GRF gel (5.99 ± 0.02 Pa), as compared to SBH-GRF (6.27 ± 0.04 Pa) and control (6.33 ± 0.04 Pa). A detail of rheological behaviour of the gels was further explained using power law. Overall, this GRF gel model has successfully demonstrated the potential of honey diastase in weakening network of starch-based food.
A green regenerated superabsorbent hydrogel was fabricated with mixtures of dissolved oil palm empty fruit bunch (EFB) cellulose and sodium carboxymethylcellulose (NaCMC) in NaOH/urea system. The formation of hydrogel was aided with epichlorohydrin (ECH) as a crosslinker. The resultant regenerated hydrogel was able to swell >80,000% depending on the NaCMC concentrations. The hydrogel absorbed water rapidly upon exposure to water up to 48 h and gradually declined after 72 h. The crosslinked of covalent bond of COC between dissolved EFB cellulose (EFBC) with NaCMC was confirmed with Attenuated total reflectance Fourier transform infrared (ATR-FT-IR) spectroscopy. Crystallinity and thermal stability of the hydrogel samples were depended on the concentrations of NaCMC, crosslinking, and swelling process. The strength and stability of crosslinked network was studied by examining the gel fraction of hydrogel. This study explored the swelling ability and probable influenced factors towards physical and chemical properties of hydrogel.
The influence of oyster mushroom (pleurotus sajor-caju, PSC) powder on the physical
properties of herbal seasoning (HS) was investigated. The pH, total solid, viscosity, rheology
and texture of semi solid HS containing different PSC powder level (0%, 20%, 40%, 60%,
8%, 100% w/w) of coconut milk powder were measured. The pH of the products were in the
range of 4.05 - 4.15. Rheological behavior was characterized by oscillatory rheometry. Stress
sweep, frequency sweep and steady stress experiments were conducted to study the behavior
of the products. The products showed non Newtonian characteristic or shear thinning. All
samples were G’> G’’ showed the gel like network. In addition, the back extrusion rig texture
analysis showed the correlation among the samples were also studied. Total substitution of PSC
powder (100% w/w) in the formulation resulted more viscous product and the combination
of the coconut milk powder and PSC powder showed the best spreadability and flow to the
product characteristics. No added PSC powder (0% w/w) showed the least viscous products
and the less moduli among the samples studied. The present study suggested the incorporation
of more than 40% PSC powder to replace coconut milk powder give better flowability and not
affect the viscosity of the products.
This paper addresses erosion prediction in 3-D, 90° elbow for two-phase (solid and liquid) turbulent flow with low volume fraction of copper. For a range of particle sizes from 10 nm to 100 microns and particle volume fractions from 0.00 to 0.04, the simulations were performed for the velocity range of 5-20 m/s. The 3-D governing differential equations were discretized using finite volume method. The influences of size and concentration of micro- and nanoparticles, shear forces, and turbulence on erosion behavior of fluid flow were studied. The model predictions are compared with the earlier studies and a good agreement is found. The results indicate that the erosion rate is directly dependent on particles' size and volume fraction as well as flow velocity. It has been observed that the maximum pressure has direct relationship with the particle volume fraction and velocity but has a reverse relationship with the particle diameter. It also has been noted that there is a threshold velocity as well as a threshold particle size, beyond which significant erosion effects kick in. The average friction factor is independent of the particle size and volume fraction at a given fluid velocity but increases with the increase of inlet velocities.
This study was focused on investigating the optimum fluidising velocity during the combustion of rice husk in a bench-scale fluidised bed combustor (ID 210mm) to obtain low carbon ash in the amorphous form. When all other parameters are held constant, the optimum fluidizing velocity aids in almost complete combustion, thereby releasing the entrapped carbon for further conversion. This results in ash with consistently low carbon content (less than 2wt%). The range of fluidising velocities investigated was from as low as 1.5U(mf) to as high as 8U(mf). It was found that the optimum fluidising velocity was approximately 3.3U(mf) as the mixing of rice husk with the bed was good with a high degree of penetration into the sand bed. The resulting ash retained its amorphous form with low residual carbon content (at 2.88wt%) and minimal sand contamination as shown by the X-ray diffraction analysis.
Extensive studies have been carried out on the effect of temperature and salt concentration on the theological behavior of whey proteins and different starches individually, but not on mixed dispersions of whey protein isolates and starches. In the present studies, the rheological behavior of cross-linked waxy maize starch and whey protein isolate mixed dispersions during heating at 60-85 degrees C was investigated. Further, the effect of CaCl2 (25-100 mM ionic strengths) on the gelatinization of these dispersions was determined. It was found that at a 2:3 ratio and a 3:2 ratio of cross-linked waxy maize starch to whey protein isolate mixed gels form a compatible networkmM concentration the solution viscosity was higher.
This study investigates effects from different drying methods (vacuum oven dried vs. freeze dried) on the rheological, functional and structural properties of chicken skin gelatin compared to bovine gelatin. Vacuum oven dried chicken skin samples showed a higher gelatin yield (12.86%) than freeze-dried samples (9.25%). The latter showed a higher melting temperature (32.64oC) and superior foaming capacity (176%) as well as foaming stability (166.67%). Vacuum oven dried samples demonstrated greater fat binding capacity (5.5 ml/g) and emulsion stability (55.79%). There were no significant differences (p >0.05) in emulsion and water holding capacity for three gelatins. Bovine gelatin did hold the lowest of all functional properties studied. A Fourier Transform Infrared (FTIR) spectrum analysis of chicken skin gelatin under both drying methods presented structures similar to those of bovine gelatin. Collectively, this findings indicated no significant differences (p >0.05) in rheological, functional and structural properties for chicken skin gelatins prepared by either drying method. Hence, to save costs and maintain gelatin quality, vacuum oven drying offers potential as an alternative means of production.
Ice cream contains high sugar content and therefore it is in contradiction with the concept of healthy diet. The objective of this study is to determine the suitability of using stevia as an alternative natural sweetener in making ice cream. In- house ice cream formulation (as the control) and three different concentrations of stevia ice cream formulations of (A, B and C) were used. Physical properties of the ice cream such as the overrun, total soluble solid, meltdown rate, rheology, and textural properties were evaluated. All ice cream samples exhibited a nonNewtonian flow with pseudoplastic behavior. Stevia ice cream has a lower melting rate and has a higher sustainability. The power law also showed that apparent viscosities of stevia ice cream were higher. Therefore, stevia can be used as a natural sugar substitute in ice cream production.
The application of membrane separation in palm oil refining process has potential for energy and cost savings. The conventional refining of crude palm oil results in loss of oil and a contaminated effluent. Degumming of crude palm oil by membrane technology is conducted in this study. The objective of this research is to study the feasibility of membrane filtration for the removal of phospholipids in the degumming of crude palm oil, including analyses of phosphorus content, carotene content free fatty acids (as palmitic acid), colour and volatile matter. A PCI membrane module was used which was equipped with polyethersulfone membranes having a molecular weight cut off of 9,000 (type ES209). In this study, phosphorus content was the most important parameter monitored. The membrane effectively removed phospholipids resulting in a permeate with a phosphorus content of less than 0.3 ppm The percentage removal of phosphorus was 96.4% and was considered as a good removal. Lovibond colour was reduced from 27R 50Y to 20R 30Y. The percentage removal of carotene was 15.8%. The removal of colour was considered good but the removal of carotene was considered insignificant by the membrane. Free fatty acids and volatile matter were not removed. Typical of membrane operations, the permeate flux decreased with time and must be improved in order to be adopted on an industrial scale. Membrane technology was found to have good potential in crude palm oil degumming. However, an appropriate method has to be developed to clean the membranes for reuse.
This study examines and compares the influence of pH on the functional, rheological and structural properties of eel skin (Monopterus sp.) and bovine gelatins. Functional properties studied and compared were emulsifying capacity and stability; water holding capacity; fat binding capacity; foaming capacity; and foaming stability. The rheological properties studied include gel strength and dynamic oscillatory measurements. The structural properties of eel skin and bovine gelatin were determined by Fourier transform infrared spectroscopy (FTIR). Results obtained showed that eel skin gelatin treated at pH 8 (compared to pH 5) exhibited the higher emulsifying, fat binding, foaming and viscoelasticity properties. The FTIR spectrum assay showed that eel skin gelatin presented a similar structure to that of bovine gelatin. This study demonstrated that pH levels influence functional, rheological and structural properties of eel skin gelatin and that these properties were enhanced to either equal or surpass those of bovine gelatin. Hence, this study indicates that eel skin gelatin has immense potential for use as an alternative to bovine gelatin.
The development of food products using composite flour has increased and is attracting much attention from researchers, especially in the production of bakery products and pastries. This article focuses on the use of composite flour to produce food products, namely bread, biscuits, and pasta, with looks at on its impact, following some improvements made, on the sensory quality, rheology characteristics, and nutritional values as well as its overall acceptance. The blending of wheat flour with various sources of tubers, legumes, cereals and fruit flour in different percentages to produce variety of food products are also reported in this review. It was found that composite flour used to produce food products is still able to maintain similar characteristics to products made from full-wheat flour. The positive effects of the use of composite flour can be seen in the final product related to the functional and physicochemical properties and health benefits of raw blended flour along with percentage blending. Overall, composite flour is a good new approach to utilizing uncommon food products as the application of composite flour produced products with different characteristics and quality, depending on the types and percentage of wheat flour used in the formulation.
A study was carried out to compare the cookie dough properties and cookie quality made out
of pink guava oil-palm stearin blends and lard (LD). Since LD is prohibited under religious
restrictions, plant shortenings were prepared by mixing pink guava seed oil with palm stearin
(PGO/PS) in different ratios: PGO-1, 40:60; PGO-2, 45:55; PGO-3, 50:50; PGO-4; 55:45 as
replacement. The effect of these formulated plant-based shortenings and LD shortening were
compared on dough rheological properties and cookie quality. Rheology and hardness of the
cookie dough were evaluated using Texture Analyser (TA). Cookie hardness was evaluated
with TA while cookie surface colors were measured using the CIE L*a*b* colorimetric system.
Among the samples, cookies made out of PGO-2 with the ratio 45:55 (PGO:PS) performed the
best substitute for LD to be used as shortening in cookies. PGO-2 also displayed the closest
similarity to LD in cookies for hardness, size and thickness, cracking size as well as colour.
As PGO-2 was a shortening formulated with plant-based ingredients, it could comply with the
halal and toyyiban requirements.
Polymer composites are fabricated by incorporating fillers into a polymer matrix. The intent for addition of fillers is to improve the physical, mechanical, chemical and rheological properties of the composite. This study reports on a unique polymer composite using hydrochar, synthesised by microwave-assisted hydrothermal carbonization of rice husk, as filler in polylactide matrix. The polylactide/hydrochar composites were fabricated by incorporating hydrochar in polylactide at 5%, 10%, 15% and 20 wt% by melt processing in a Haake rheomix at 170 °C. Both the neat polylactide and polylactide/hydrochar composite were characterized for mechanical, structural, thermal and rheological properties. The tensile modulus of polylactide/hydrochar composites was improved from 2.63 GPa (neat polylactide) to 3.16 GPa, 3.33 GPa, 3.54 GPa, and 4.24 GPa after blending with hydrochar at 5%, 10%, 15%, and 20%, respectively. Further, the incorporation of hydrochar had little effect on storage modulus (G') and loss modulus (G″). The findings of this study reported that addition of hydrochar improves some characteristics of polylactide composites suggesting the potential of hydrochar as filler for polymer/hydrochar composites.
Fullerene nanoemulsions were formulated in palm kernel oil esters stabilized by low amount of mixed nonionic surfactants. Pseudoternary phase diagrams were established in the colloidal system of PKOEs/Tween 80 : Span 80/water incorporated with fullerene as antioxidant. Preformulation was subjected to combination of high and low energy emulsification methods and the physicochemical characteristics of fullerene nanoemulsions were analyzed using electroacoustic spectrometer. Oil-in-water (O/W) nanoemulsions with particle sizes in the range of 70-160 nm were formed. The rheological characteristics of colloidal systems exhibited shear thinning behavior which fitted well into the power law model. The effect of xanthan gum (0.2-1.0%, w/w) and beeswax (1-3%, w/w) in the estimation of thermodynamics was further studied. From the energetic parameters calculated for the viscous flow, a moderate energy barrier for transport process was observed. Thermodynamic study showed that the enthalpy was positive in all xanthan gum and beeswax concentrations indicating that the formation of nanoemulsions could be endothermic in nature. Fullerene nanoemulsions with 0.6% or higher xanthan gum content were found to be stable against creaming and flocculation when exposed to extreme environmental conditions.