Effects of organoclay concentration on the properties of radiation crosslinked natural rubber (NR)/ ethylene vinyl acetate (EVA)/clay nanocomposites were investigated. The NR/EVA blend with a ratio of 40/60 was melt blended with different concentration of either dodecyl ammonium montmorillonite (DDA-MMT) or dimethyl dihydrogenated tallow quarternary ammonium montmorillonite (C20A). Composite of NR/EVA blend with unmodified clay (Na-MMT) was also prepared for comparison purposes. The composites were irradiated with electron beam (EB) at an optimum irradiation dose. The formation of radiation-induced crosslinking depends on the type and concentration of the organoclay used in the preparation of nanocomposites as measured by gel content. Changes in the interlayer distance of the silicate layers with the increase of organoclay concentration were shown by the XRD results. Variation in the tensile properties of the nanocomposites with the increase of organoclay concentration depends on the formation of crosslinking as well as reinforcement effect of the organoclay. Improvement in thermal stability of the NR/EVA blend was also observed with the presence of organoclay.
Electron beam vulcanization of natural rubber latex has been developed as an alternative to the conventional sulphur vulcanization method. This study aimed at determining the effect of electron beam dose, beam current and centrifugation to the tensile properties of field natural rubber latex. Irradiation dose and beam current ranged from 50 to 300 kGy and 1 to 15 mA respectively. The determination of tensile properties were done on cast film prepared from irradiated field latex before and after centrifugation. It was found that tensile properties increased with radiation dose but decreased with beam current. Rubber films made from centrifuged irradiated field latex were softer and showed higher tensile strength.
Bottom-contact pentacene OTFTs are fabricated using cross-linked poly(vinyl alcohol) (PVA) insulator and its reliability characteristics are analyzed. The hysteresis of the OTFTs is mainly caused by the electrons that are injected from the gate electrode to the cross-linked PVA insulator. To block the injection of electrons, plasma-enhanced chemical vapor deposition (PECVD) SiO2 layer is inserted between the gate electrode and the cross-linked PVA layer, so that the minimum hysteresis can be obtained. In addition, the effects of the gate bias stress as a function of time is investigated to examine the long-term reliability of the device during the operation.
Modern linear accelerators, the predominant teletherapy machine in major radiotherapy centres worldwide, provide multiple electron and photon beam energies. To obtain reasonable treatment times, intense electron beam currents are achievable. In association with this capability, there is considerable demand to validate patient dose using systems of dosimetry offering characteristics that include good spatial resolution, high precision and accuracy. Present interest is in the thermoluminescence response and dosimetric utility of commercially available doped optical fibres. The important parameter for obtaining the highest TL yield during this study is to know the dopant concentration of the SiO2 fibre because during the production of the optical fibres, the dopants tend to diffuse. To achieve this aim, proton-induced X-ray emission (PIXE), which has no depth resolution but can unambiguously identify elements and analyse for trace elements with detection limits approaching microg/g, was used. For Al-doped fibres, the dopant concentration in the range 0.98-2.93 mol% have been estimated, with equivalent range for Ge-doped fibres being 0.53-0.71 mol%. In making central-axis irradiation measurements a solid water phantom was used. For 6-MV photons and electron energies in the range 6, 9 and 12 MeV, a source to surface distance of 100 cm was used, with a dose rate of 400 cGy/min for photons and electrons. The TL measurements show a linear dose-response over the delivered range of absorbed dose from 1 to 4 Gy. Fading was found to be minimal, less than 10% over five days subsequent to irradiation. The minimum detectable dose for 6-MV photons was found to be 4, 30 and 900 microGy for TLD-100 chips, Ge- and Al-doped fibres, respectively. For 6-, 9- and 12-MeV electron energies, the minimum detectable dose were in the range 3-5, 30-50 and 800-1400 microGy for TLD-100 chip, Ge-doped and Al-doped fibres, respectively.
The paper examines the propagation direction and speed of large scale travelling ionospheric disturbances (LSTIDs) obtained from GPS observations of extreme geomagnetic storms during the 23rd solar cycle; these are the October 2003 and November 2003 geomagnetic storms. In the analysis, the time delay between total electron content (TEC) structures at Scott Base station (SBA) (Lat. –77.85º, Long. 166.76º), McMurdo (McM4), (Lat. –77.84º, Long. 166.95º), Davis (DAV1), (Lat. –68.58º, Long. 77.97º) and Casey station (CAS1) (Lat. –66.28º, Long. 110.52º) GPS stations as well as the distance between these stations were employed in the analysis. The measurements during the October 2003 storm showed obvious time delay between the TEC enhancement occurrences at SBA/MCM4, DAV1 and CAS1 stations. The time delay indicated a movement of the ionospheric structures from higher to lower latitudes in a velocity ranging between 0.8 km/s – 1.2 km/s. The first sudden TEC enhancement was observed at SBA/McM4 (Lat. –75.84º) followed by CAS1 station (Lat. –66.28º) and the final TEC enhancement was seen at DAV1 station (Lat. –68.58º) with TEC magnitude decreasing while moving from higher to lower latitudes. One important observation was that although the latitude of the CAS1 station was lower than the DAV1 station, the TEC enhancement was firstly seen at the CAS1 station due to the shorter distance between SBA and CAS1 compared with the distance between SBA and CAS1 of about 500 km. The TEC measurements during the November 2003 storm showed an opposite propagation direction (i.e. poleward direction from lower to higher latitudes) which was seen with a velocity ranging between 0.3 km/s – 0.4 km/s. As similar response was observed using vertical TEC measurements obtained from individual PRN satellites but with higher velocity ranges (1.2 km/s – 2.4 km/s during October
and 0.5 km/s – 0.7 km/s during November). The equatorward or poleward expansion of LSTIDs during the October and November 2003 storms was probably caused by the disturbances in the neutral temperature which occurred close to the dayside convection throat or due to the neutral wind oscillation induced by atmospheric gravity waves launched from the aurora region.
Changes to the physicochemical properties of wheat, sago and tapioca starches subjected to gamma ray, electron beam and microwave irradiations and the conditions that lead to wheat starch having leaching behaviour similar to sago or tapioca starch were studied. The properties were characterised through swelling and leaching behaviours of the starch granules and retrogradation following pasting. The leaching of wheat starch increased tremendously and resulted in amylose to amylopectin ratios in the leachate similar to that of native sago and tapioca starches. This observation is significant as wheat starch is known to have a leachate composition of mostly amylose. This opens up the possibility of utilising wheat starch in snacks where tapioca and sago starch are commonly used. It was observed that the required conditions for such changes were exposure to microwave for 8 and 10 minutes, electron beam at 5 and 10 kGy and gamma ray at 5 kGy.
Monoclinic bismuth oxide (α-Bi2O3) nanoparticles were prepared via precipitation method and
irradiated with a pulsed laser forming thin films. Their phase and surface morphological properties
were investigated using x-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron
microscopy (SEM) and high resolution transmission electron microscopy (HR-TEM). The XRD
analysis shows the phase transformation to a partially crystalline tetragonal phase β-Bi2O3 thin film.
The SEM micrograph of the nanoparticles, with an average crystal size of 72 nm, was seen to form
a thin film with a peculiar structure, coined as “cotton-like”, is attributed to the high surface energy
absorbed by the nanoparticles during ablation. The HR-TEM micrograph shows the particulate with
a clearly defined interlayer spacing.
Neutron aperture is one of the collimator components in a neutron radiography facility. The optimum design of neutron aperture is very importance in order to obtain largest L/D ratio with highest thermal neutron flux and low gamma-rays at the image plane. In this study, the optimization of neutron aperture parameters were done using Monte Carlo N-Particle Transport Code, version five (MCNP5). This code has a capability to simulate the neutron, photon, and electron or coupled of neutron/photon/electron transport, including the capability to calculate eigen values for critical system. The aperture parameters concerned in this study are the selection of best aperture material, aperture thickness, aperture position and aperture center hole diameter. In these simulations, vacuum beam port medium was applied.
Elevated temperature affects marine benthic algae by reducing growth and limits the transport of electron or carbon fixation which may reduce the ability of the cell to use light. This resulting excess light energy may cause photoinhibition. In this study, the photosystem II of the benthic microalgal communities from Casey, eastern Antarctic were relatively unaffected by significant changes in temperatures up to 8ºC, along with high PAR level (450 μmol photons m–2 s–1). Similarly, the community was able to photosynthesize as the temperature was reduced to –5ºC. Recovery from saturating and photoinhibiting irradiances was not significantly influenced by temperatures at both –5ºC and 8ºC. These responses were consistent with those recorded by past experiments on Antarctic benthic diatoms and temperate diatoms which showed that climate change did not have a significant impact on the ability of benthic microalgae to recover from photoinhibitory temperature stress.
Precipitated calcium carbonate fillers were loaded into the lumen of bleached mixed tropical hardwood pulp using polyethylenimine (PEI) and alum. Our results indicated that the addition of (PEI) increased the degree of loading of precipitated calcium carbonate (PCC) into the lumen of fibers. The degree of loading also increased with the addition of alum together with PEI. The mechanical strengths of the produced lumen loaded paper increased with the addition of PEI and alum. Meanwhile the mechanical strength without alum had slightly increased the mechanical strengths of the paper. Electron micrographs revealed that the PCC fillers were successfully loaded into the lumen of the fibers.
An electron beam (EB) flue gas test rig and a dielectric barrier discharge (DBD) reactor were tested for the removal of nitric oxide (NO) from gas stream in separate experiments. In both systems, energised electrons were used to produce radicals that reacted with the pollutants. The EB system was a laboratory scale test rig used to treat emission from a diesel run generator. At 1.0 MeV and 10 mA more than 90% NO removal from flue gases flowing at 120 Nm3/h can be achieved. For higher removal percentage, higher beam current was required. In a related effort, a table top, two tubes DBD reactor was used to process bottled gases containing 106 ppm NO. Total removal (>99%) was achieved when the inlet gas contained only NO and N2. Additional SO2 in the in let gas stream lowered the removal rate but was overcame by scaling up the system to 10 DBD tubes. The system was operated with input AC voltage of 35 kV peak to peak. In the EB treatment system, the amount of NO2 increased at high beam current, showing that the NO was also oxidised in the process. Whereas in the DBD reactor, the amount of NO2 remained insignificant throughout the process. This leads to the conclusion that the DBD reactor is capable of producing total removal of NO. This is highly desirable as post treatment will not be necessary.
Titanium dioxide particles were successfully prepared using microemulsion-mediated hydrothermal processing route, with sucrose ester as a stabilising agent. X-ray diffraction patterns revealed that the particles possessed anatase crystal phase. Scanning electron micrographs showed micron-sized spherical particles with rough and smooth surfaces, which eventually interconnected with one another. The formation mechanism of the titanium dioxide microstructures was postulated. The as-prepared particles were subjected to photocatalytic degradation of methylene blue, which exhibited higher photocatalytic activity compared to their commercial counterpart.
Hydrogen produced from the photocatalytic splitting of water is one of the reliable alternatives to replace the polluting fossil and the radioactive nuclear fuels. Here, we provide unequivocal evidence for the existence of blue- and red-shifting O-H covalent bonds within a single water molecule adsorbed on the MgO surface as a result of asymmetric displacement polarizabilities. The adsorbed H-O-H on MgO gives rise to one weaker H-O bond, while the other O-H covalent bond from the same adsorbed water molecule compensates this effect with a stronger bond. The weaker bond (nearest to the surface), the interlayer tunneling electrons and the silver substrate are shown to be the causes for the smallest dissociative activation energy on the MgO monolayer. The origin that is responsible to initiate the splitting mechanism is proven to be due to the changes in the polarizability of an adsorbed water molecule, which are further supported by the temperature-dependent static dielectric constant measurements for water below the first-order electronic-phase transition temperature.
A Schottky diode has been designed and fabricated on an n-AlGaAs/GaAs high-electron-mobility-transistor (HEMT) structure. Current-voltage (I-V) measurements show good device rectification, with a Schottky barrier height of 0.4349 eV for Ni/Au metallization. The differences between the Schottky barrier height and the theoretical value (1.443 eV) are due to the fabrication process and smaller contact area. The RF signals up to 1 GHz are rectified well by the fabricated Schottky diode and a stable DC output voltage is obtained. The increment ratio of output voltage vs input power is 0.2 V/dBm for all tested frequencies, which is considered good enough for RF power detection. Power conversion efficiency up to 50% is obtained at frequency of 1 GHz and input power of 20 dBm with series connection between diode and load, which also shows the device's good potential as a rectenna device with further improvement. The fabricated n-AlGaAs/GaAs Schottky diode thus provides a conduit for breakthrough designs for RF power detectors, as well as ultra-low power on-chip rectenna device technology to be integrated in nanosystems.
The sensing responses in aqueous solution of an open-gated pH sensor fabricated on an AlGaN/GaN high-electron-mobility-transistor (HEMT) structure are investigated. Under air-exposed ambient conditions, the open-gated undoped AlGaN/GaN HEMT only shows the presence of a linear current region. This seems to show that very low Fermi level pinning by surface states exists in the undoped AlGaN/GaN sample. In aqueous solution, typical current-voltage (I-V) characteristics with reasonably good gate controllability are observed, showing that the potential of the AlGaN surface at the open-gated area is effectively controlled via aqueous solution by the Ag/AgCl gate electrode. The open-gated undoped AlGaN/GaN HEMT structure is capable of distinguishing pH level in aqueous electrolytes and exhibits linear sensitivity, where high sensitivity of 1.9 mA/pH or 3.88 mA/mm/pH at drain-source voltage, V(DS) = 5 V is obtained. Due to the large leakage current where it increases with the negative gate voltage, Nernstian like sensitivity cannot be determined as commonly reported in the literature. This large leakage current may be caused by the technical factors rather than any characteristics of the devices. Surprisingly, although there are some imperfections in the device preparation and measurement, the fabricated devices work very well in distinguishing the pH levels. Suppression of current leakage by improving the device preparation is likely needed to improve the device performance. The fabricated device is expected to be suitable for pH sensing applications.
In this studies gamma and electron beam irradiation was used to treat textile waste water. Comparisons between both types of irradiation in terms of effectiveness to degrade the pollutants present in textile waste water were done. Prior to irradiation, the raw wastewater was diluted using distilled water to a target concentration of COD 400 mg/l. The sample was irradiated at selected doses between the ranges of 10 kGy to 100 kGy. The results showed that irradiation has significantly contributed in the reduction of the highly colored refractory organic pollutants. The COD removal at the lowest dose, 10 kGy was reduced to 390 mg/l for gamma and 400 mg/l for electron beam. Meanwhile, at the highest dose, 100 kGy, the COD was reduced to 125 mg/l for gamma and 144 mg/l for electron beam. The degree of removal is influenced by the dose introduced during the treatment process. As the dose increased, the higher the removal of organic pollutant was recorded. However, gamma irradiation is more effective although the differences are not significant between gamma and electron beam irradiation. On the other hand, other properties of the wastewater such as pH, turbidity, suspended solid, BOD and color also shows a gradual decrease as the dose increases for both types of irradiation.
The total mass attenuation coefficients (μ/ρ) of stainless steel (SS316L) and carbon steel (A516) that are widely used as petrochemical plant components, such as distillation column, heat exchanger, boiler and storage tank were measured at 662, 1073 and 1332 keV of photon energies. Measurements of radiation intensity for various thicknesses of steel were made by using transmission method. The γ-ray intensity were counted by using a Gamma spectrometer that contains a Hyper-pure Germanium (HPGe) detector connected with Multi Channel Analyzer (MCA). The effective numbers of atomic (Zeff) and electron (Neff) obtained experimentally were compared by those obtained through theoretical calculation. Both experimental and calculated values of Zeff and Neff were in good agreement.
This review briefly describes some of the techniques available for analysing surfaces and illustrates their usefulness with a few examples such as a metal and alloy. In particular, Auger electron spectroscopy (AES), X-ray photoelectron spectroscopy (XPS) and laser Raman spectroscopy are all described as advanced surface analytical techniques. In analysing a surface, AES and XPS would normally be considered first, with AES being applied where high spatial resolution is required and XPS where chemical state information is needed. Laser Raman spectroscopy is useful for determining molecular bonding. A combination of XPS, AES and Laser Raman spectroscopy can give quantitative analysis from the top few atomic layers with a lateral spatial resolution of
Serbuk sekam padi (SP) merupakan serabut semula jadi yang boleh bertindak sebagai pengisi penguat dalam adunan getah asli termoplastik (TPNR) NR/HDPE selepas permukaan serbuk dimodifikasikan sewajarnya. Rawatan serbuk SP merangkumi pra-rawatan dengan 5% larutan natrium hidroksida (NaOH), rendaman dalam larutan getah asli cecair (LNR) dan dedahan SP tersalut LNR kepada sinaran electron (EB). Komposit TPNR/SP disediakan secara pengadunan leburan dalam pengadun dalaman pada keadaan yang telah ditentupastikan terlebih dahulu. Morfologi komposit yang dianalisis menggunakan mikroskop elektron imbasan (SEM), menunjukkan taburan zarah pengisi SP termodifikasi adalah homogen dan kewujudan interaksi matriks-zarah. Komposit terisi SP terubahsuai LNR-EB menunjukan perubahan sifat mekanik yang ketara. Nilai maksimum tegasan dan kekuatan impak adalah masing masing 6.7 MPa dan 13.2 kJ/cm2 pada dedahan 20 kGy dos EB, manakala modulus regangan adalah 79 MPa pada dos 30 kGy. Ini menunjukkan terdapat peningkatan interaksi berkesan antara-muka SP dan TPNR bagi SP terwat LNR pada dos 20-30kGy EB. Peningkatan dos EB pada SP tersalut LNR menyebabkan degradasi salutan NR dan meningkatakan interaksi antara zarah SP. Pengaglomerasian zarah SP akan berlaku dan menyebabkan serakan zarah dalam komposit menjadi tidak homogen.
In this research we investigated the effect of composition on the fabrication and morphological characteristics of a hybrid polymeric solar cell which consists of an electron donating conjugated polymer, namely is poly(3-hexylthiophene) (P3HT) combined with an electron-accepting component, which is a type of inorganic compound of TiO2 nanocrystals. The composition of TiO2 in the blends is varied and the optimum performance of the devices are studied. The optical and morphological characterizations are carried out via UV-Visible absorption spectroscopy, X-ray diffraction (XRD), atomic force microscopy (AFM) and scanning electron microscopy (SEM). The electrical characteristics of the devices are measured by using Keithley 2400 SMU and solar simulator with light intensity of 100 mW/cm2.