BACKGROUND: Pharmaceutical representatives provide medicines information on their promoted products to doctors. However, studies have shown that the quality of this information is often low. No study has assessed the medicines information provided by pharmaceutical representatives to doctors in Malaysia and no recent evidence in Australia is present. We aimed to compare the provision of medicines information by pharmaceutical representatives to doctors in Australia and Malaysia.
METHODS: Following a pharmaceutical representative's visit, general practitioners in Australia and Malaysia who had agreed to participate, were asked to fill out a questionnaire on the main product and claims discussed during the encounter. The questionnaire focused on provision of product information including indications, adverse effects, precautions, contraindications and the provision of information on the Pharmaceutical Benefit Scheme (PBS) listings and restrictions (in Australia only). Descriptive statistics were produced. Chi-square analysis and clustered linear regression were used to assess differences in Australia and Malaysia.
RESULTS: Significantly more approved product information sheets were provided in Malaysia (78%) than in Australia (53%) (P < 0.001). In both countries, general practitioners reported that indications (Australia, 90%, Malaysia, 93%) and dosages (Australia, 76%, Malaysia, 82%) were frequently provided by pharmaceutical representatives. Contraindications, precautions, drug interactions and adverse effects were often omitted in the presentations (range 25% - 41%). General practitioners in Australia and Malaysia indicated that in more than 90% of presentations, pharmaceutical representatives partly or fully answered their questions on contraindications, precautions, drug interactions and adverse effects. More general practitioners in Malaysia (85%) than in Australia (60%) reported that pharmaceutical representatives should have mentioned contraindications, precautions for use, drug interaction or adverse effects spontaneously (P < 0.001). In 48% of the Australian presentations, general practitioners reported the pharmaceutical representatives failed to mention information on PBS listings to general practitioners.
CONCLUSIONS: Information on indications and dosages were usually provided by pharmaceutical representatives in Australia and Malaysia. However, risk and harmful effects of medicines were often missing in their presentations. Effective control of medicines information provided by pharmaceutical representatives is needed.
Palm oil is one of the most important agroindustries in Malaysia. Huge quantities of palm oil mill effluent (POME) pose a great threat to aqueous environment due to its very high COD. To make full use of discharged wastes, the integrated "zero discharge" pilot-scale industrial plant comprising "pretreatment-anaerobic and aerobic process-membrane separation" was continuously operated for 1 year. After pretreatment in the oil separator tank, 55.6% of waste oil in raw POME could be recovered and sold and anaerobically digested through 2 AnaEG reactors followed by a dissolved air flotation (DAF); average COD reduced to about 3587 mg/L, and biogas production was 27.65 times POME injection which was used to generate electricity. The aerobic effluent was settled for 3 h or/and treated in MBR which could remove BOD3 (30°C) to less than 20 mg/L as required by Department of Environment of Malaysia. After filtration by UF and RO membrane, all organic compounds and most of the salts were removed; RO permeate could be reused as the boiler feed water. RO concentrate combined with anaerobic surplus sludge could be used as biofertilizer.
The study is to identify the extraction of intracellular inulinase (exo- and endoinulinase) and invertase as well as optimization medium composition for maximum productions of intra- and extracellular enzymes from Aspergillus niger ATCC 20611. From two different methods for extraction of intracellular enzymes, ultrasonic method was found more effective. Response surface methodology (RSM) with a five-variable and three-level central composite design (CCD) was employed to optimize the medium composition. The effect of five main reaction parameters including sucrose, yeast extract, NaNO₃, Zn⁺², and Triton X-100 on the production of enzymes was analyzed. A modified quadratic model was fitted to the data with a coefficient of determination (R²) more than 0.90 for all responses. The intra-extracellular inulinase and invertase productions increased in the range from 16 to 8.4 times in the optimized medium (10% (w/v) sucrose, 2.5% (w/v) yeast extract, 2% (w/v) NaNO₃, 1.5 mM (v/v) Zn⁺², and 1% (v/v) Triton X-100) by RSM and from around 1.2 to 1.3 times greater than in the medium optimized by one-factor-at-a-time, respectively. The results of bioprocesses optimization can be useful in the scale-up fermentation and food industry.
Amylase is an important and indispensable enzyme that plays a pivotal role in the field of biotechnology. It is produced mainly from microbial sources and is used in many industries. Industrial sectors with top-down and bottom-up approaches are currently focusing on improving microbial amylase production levels by implementing bioengineering technologies. The further support of energy consumption studies, such as those on thermodynamics, pinch technology, and environment-friendly technologies, has hastened the large-scale production of the enzyme. Herein, the importance of microbial (bacteria and fungi) amylase is discussed along with its production methods from the laboratory to industrial scales.
The recent growth of biotechnology requires a wide range of expertise within the industry. Education is the primary platform for students to gain information and knowledge on biotechnology. In Malaysia where biotechnology is relatively new, education programs and courses must be tailored to meet the demands of the industry. A combination of theoretical knowledge as well as practical and industrial training is essential to ensure graduates are prepared for their career in the fields of biotechnology. Results from this study show that university students lack literacy on biotechnology information and access to facilities provided by the universities. This may be a significant contributing factor to the lack of knowledge and information amongst graduates. Furthermore comparative analysis on the biotechnology program in Malaysian universities with that of other countries show the need to restructure the program by offering more specialized courses as well as soft skills and business subjects. This is to meet the demands of the related professionals as well as the various branches that exist in the biotechnology industry.
Sulfur has been highly sought by many industries everywhere around the world for various applications. This exceptionally useful element has been largely manufactured especially in powder form each year reflecting its increase in demand in line with technological advancement and uses for various product applications. The manufacturing processes include mining as well as chemical reactions in Claus Process. Rubber industries normally use abundance of sulfur in their latex compound to introduce vulcanization. The geneal concern of sulfur for rubber vulcanization is dispersibility in the rubber matrix due to improper optimization of its preparation process prior to latex compounding. Another crucial issue is crystallization of soluble sulfur from its insoluble origin, either during or post-rubber vulcanization that constitutes to formation of sulfur bloom that grows on the surface of the rubber articles. It is known that both issues are related to the process conditions and compounding recipe that could not be fully solved. Various studies have been conducted to minimize such occurences – from process optimization to sulfur chemistry itself – and of continuous improvement and innovation to solve various threats in sulfur applications. This paper reviews on detailed description on elemental sulfur, of respective industrial applications, and most importantly highlights on sulfur trends and issues normally encountered.
The biosimilars sector continues to attract huge interest and controversy. Biosimilars are new biopharmaceuticals that are "similar" but not identical to the innovator product. Characteristics of biopharmaceuticals are closely related to the manufacturing process, which implies that the products cannot be exactly duplicated. Minuscule differences in the product's structure and manufacturing process can result in different clinical outcome. This raises concerns over the safety, efficacy and even pharmacovigilance of biosimilars. Thus, biosimilars are unique - they are not a true chemical generic and are regulated via a distinct regulatory framework. This report discusses the features of Malaysian regulatory oversight of biosimilars and experience acquired in the evaluation of some products from various countries. Ensuring regulatory position adequately reflects scientific advancement, expertise/resources is key. The regulatory situation is an evolving process. Various guidance documents are being prepared with the aim of developing a uniform global framework towards assuring the dual goal of lower costs and patient safety while expediting the availability of important biosimilar products.
Matched MeSH terms: Drug Industry/legislation & jurisprudence*; Drug Industry/standards*
The current research investigates synthesis of methyl esters by transesterification of waste cooking oil in a heterogeneous system, using barium meliorated construction site waste marble as solid base catalyst. The pretreated catalyst was calcined at 830 °C for 4h prior to its activity test to obtained solid oxide characterized by scanning electron microscopy/energy dispersive spectroscopy, BET surface area and pore size measurement. It was found that the as prepared catalyst has large pores which contributed to its high activity in transesterification reaction. The methyl ester yield of 88% was obtained when the methanol/oil molar ratio was 9:1, reaction temperature at 65 °C, reaction time 3h and catalyst/oil mass ratio of 3.0 wt.%. The catalyst can be reused over three cycles, offer low operating conditions, reduce energy consumption and waste generation in the production of biodiesel.
Matched MeSH terms: Food Industry; Construction Industry
A micro-mesoporous activated carbon (AC) was produced via an innovative approach combining microwave pyrolysis and chemical activation using NaOH/KOH mixture. The pyrolysis was examined over different chemical impregnation ratio, microwave power, microwave irradiation time and types of activating agents for the yield, chemical composition, and porous characteristic of the AC obtained. The AC was then tested for its feasibility as textile dye adsorbent. About 29 wt% yield of AC was obtained from the banana peel with low ash and moisture (<5 wt%), and showed a micro-mesoporous structure with high BET surface area (≤1038 m2/g) and pore volume (≤0.80 cm3/g), indicating that it can be utilized as adsorbent to remove dye. Up to 90% adsorption of malachite green dye was achieved by the AC. Our results indicate that the microwave-activation approach represents a promising attempt to produce good quality AC for dye adsorption.
In this research we assess the feasibility of using palm oil agricultural refinery waste as a carbon source for the production of rhamnolipid biosurfactant through fermentation. The production and characterization of rhamnolipid produced by Pseudomonas aeruginosa PAO1 grown on palm fatty acid distillate (PFAD) under batch fermentation were investigated. Results show that P. aeruginosa PAO1 can grow and produce 0.43gL(-1) of rhamnolipid using PFAD as the sole carbon source. Identification of the biosurfactant product using mass spectrometry confirmed the presence of monorhamnolipid and dirhamnolipid. The rhamnolipid produced from PFAD were able to reduce surface tension to 29mNm(-1) with a critical micelle concentration (CMC) 420mgL(-1) and emulsify kerosene and sunflower oil, with an emulsion index up to 30%. Results demonstrate that PFAD could be used as a low-cost substrate for rhamnolipid production, utilizing and transforming it into a value added biosurfactant product.
The increase in solid waste has become a common problem and causes environmental pollution worldwide. A green approach to valorise solid waste for sustainable development is required. Agricultural residues are considered suitable for conversion into profitable products through solid-state fermentation (SSF). Agricultural wastes have high organic content that is used as potential substrates to produce value-added products through SSF. The importance of process variables used in solid-phase fermentation is described. The applications of SSF developed products in the food industry as flavouring agents, acidifiers, preservatives and flavour enhancers. SSF produces secondary metabolites and essential enzymes. Wastes from agricultural residues are used as bioremediation agents, biofuels and biocontrol agents through microbial processing. In this review paper, the value addition of agricultural wastes by SSF through green processing is discussed with the current knowledge on the scenarios, sustainability opportunities and future directions of a circular economy for solid waste utilisation.
Acetoin is used in the biochemical, chemical and pharmaceutical industries. Several effective methods for acetoin production from petroleum-based substrates have been developed, but they all have an environmental impact and do not meet sustainability criteria. Here we describe a simple and efficient method for acetoin production from oil palm mesocarp fiber hydrolysate using engineered Escherichia coli. An optimization of culture conditions for acetoin production was carried out using reagent-grade chemicals. The final concentration reached 29.9gL(-1) with a theoretical yield of 79%. The optimal pretreatment conditions for preparing hydrolysate with higher sugar yields were then determined. When acetoin was produced using hydrolysate fortified with yeast extract, the theoretical yield reached 97% with an acetoin concentration of 15.5gL(-1). The acetoin productivity was 10-fold higher than that obtained using reagent-grade sugars. This approach makes use of a compromise strategy for effective utilization of oil palm biomass towards industrial application.
In the last few years, biodiesel has emerged as one of the most potential renewable energy to replace current petrol-derived diesel. It is a renewable, biodegradable and non-toxic fuel which can be easily produced through transesterification reaction. However, current commercial usage of refined vegetable oils for biodiesel production is impractical and uneconomical due to high feedstock cost and priority as food resources. Low-grade oil, typically waste cooking oil can be a better alternative; however, the high free fatty acids (FFA) content in waste cooking oil has become the main drawback for this potential feedstock. Therefore, this review paper is aimed to give an overview on the current status of biodiesel production and the potential of waste cooking oil as an alternative feedstock. Advantages and limitations of using homogeneous, heterogeneous and enzymatic transesterification on oil with high FFA (mostly waste cooking oil) are discussed in detail. It was found that using heterogeneous acid catalyst and enzyme are the best option to produce biodiesel from oil with high FFA as compared to the current commercial homogeneous base-catalyzed process. However, these heterogeneous acid and enzyme catalyze system still suffers from serious mass transfer limitation problems and therefore are not favorable for industrial application. Nevertheless, towards the end of this review paper, a few latest technological developments that have the potential to overcome the mass transfer limitation problem such as oscillatory flow reactor (OFR), ultrasonication, microwave reactor and co-solvent are reviewed. With proper research focus and development, waste cooking oil can indeed become the next ideal feedstock for biodiesel.
Oil palm biomass is widely known for its potential as a renewable resource for various value-added products due to its lignocellulosic content and availability. Oil palm biomass biorefinery is an industry that comes with sociopolitical benefits through job opportunities, as well as potential environmental benefits. Many studies have been conducted on the technological advancements of oil-palm biomass-derived renewable materials, which are discussed comprehensively in this review. Recent technological developments have made it possible to bring new and innovative technologies to commercialization, such as compost, biocharcoal, biocomposites, and bioplastics.
The present study examined the factor structure of a Malay version of the Body Appreciation Scale (BAS), a recently developed scale for the assessment of positive body image that has been shown to have a unidimensional structure in Western settings. Results of exploratory and confirmatory factor analyses based on data from community sample of 591 women in Kuala Lumpur, Malaysia, failed to support a unidimensional structure for the Malay BAS. Results of a confirmatory factor analysis suggested two stable factors, which were labelled 'General Body Appreciation' and 'Body Image Investment'. Multi-group analysis showed that the two-factor structure was invariant for both Malaysian Malay and Chinese women, and that there were no significant ethnic differences on either factor. Results also showed that General Body Appreciation was significant negatively correlated with participants' body mass index. These results are discussed in relation to possible cross-cultural differences in positive body image.
Stevia rebaudiana has recently gained the attention of the food industry as one of the natural sweeteners. The sweet flavour is contributed by the glycoside compounds, especially the rebaudioside A and stevioside, which are the stevia main chemical markers. The aim of the work reported here was to compare the different extraction techniques of stevia leaves using different technologies such as the high pressure and ultrasonic on the extraction of steviol glycosides. In this paper, the extraction techniques yielding the highest glycosides from the leaves of Stevia rebaudiana were determined using hot water extraction (HWE), pressurised liquid extraction (PLE) and ultrasound-assisted extraction (UAE). The steviol glycoside yields were quantified by two chemical markers, rebaudioside A and stevioside of Stevia rebaudiana using highperformance liquid chromatography (HPLC) analysis. The result showed that the HWE managed to obtain 1,110 mg of steviol glycosides. The PLE obtained 294 mg steviol glycosides and the UAE obtained 427.5 mg steviol glycosides. As a conclusion, the results suggested the most efficient technique for stevia extraction in this study was the HWE.
Waste materials from the agricultural and industries can cause problems to human health and the environment when improperly disposed and managed. Due to rapid development in construction, the demand of cement in concrete has increased dramatically. Therefore, wastes such as rice husk, eggshell, glass, fly ash and many more can be used in construction industry to minimize the environmental impact and producing new material on construction industry. Many studies have been conducted as an effort to find replacement materials to substitute cement in concrete.