Glass ionomer cement (GIC) has theunique fluoride release property and able to formionic bond with tooth structure. However, the brittleness of the material results in low hardness. In the present study, a new approach in utilization of local waste materials as fillers for improvement of hardness of GIC is reported.The synthesized wollastonite and mine-silica by-product were individually incorporated into commercial GIC and the Vickers hardness were evaluated. The results shown that the incorporation of 1 % wollastonite into GIC gave ~ 6% increment in hardness compared to the control GIC (66.53H ±7.37 versus 62.66HV±2.98)but not for themine-silica. Thus, wollastonite could be a potential material to be utilized as fillersin dental restorative composite
Feasibility studies on the vitrification of spent ion exchange resins combined with glass cullet powder have been conducted using a High Temperature Test Furnace. Bottle glass cullet powder was used as matrix material to convert the ash of the spent resins into a glass. Vitrificat ion of spent ion exchange resins presents a reasonable disposal alternative, because of its inherent organic destruction capabilities, the volume reduction levels obtainable, and the durable product that it yields. In this study, the spent ion exchange resin from the PUSPATI TRIGA reactor of Nuclear Malaysia was combusted in a lab scale combustor and the resulting ash was vitrified together with glass cullet powder in a high temperature furnace to produce a stable spent resin ash embedded in glass. The factors affecting this immobilized waste, such as thermal stability, radiological stability and leachability have all been investigated. However, the outcome of these tests, which include the radionuclide activity concentration in the slag, the optimum conditioning temperature - in relation with volume reduction during vitrification - and the volume mixing ratio of matrix material were reported. It was found that the radionuclides present in spent resins were 54 Mn, 60 Co and 152Eu. The elementary chemical composition (carbon, hydrogen, nitrogen and sulphur) of spent resins was 27.6% C, 5.68% H, 2.04% N and 4.20% S, respectively. The maximum calorific value of spent resins was 1735 kJ/kg. The average activity concentrations of 54 Mn and 60Co in ash at 200oC were 9,411 ± 243 Bq/Kg and 12,637± 201 Bq/Kg. flue gases containing CO2, CO, SO2 and NO started to be emitted above 200oC. The optimum conditioning temperature was also the highest tested, i.e. 900oC in 45 minutes, and the best mixing ratio ash to matrix material was also the highest, ie 1:9. Finally, the leaching analysis of slag at 900oC in 45 minutes showed that the leaching activity of 60Co was below 0.5 Bq/mL.
Industrial pollution issue and dark colour of carbon black, clay based non black filler are getting more importance for reinforcing elastomer. EPDM-Kaolin composites with various maleated EPDM concentration have been prepared by mixing on a two roll mill. The rheometry data showed the optimum cure time increases with increasing compatibilizer concentration without decreasing torque value indicating that acidic functional groups comes from compatibilizer could retard cure rate and increase the optimum cure time rather than change in the ultimate cure state. As the filler
concentration increases, the edge to edge and face to edge interaction between filler and EPDM increases and the free volume between EPDM molecules is reduced, the storage modulus increases. Moreover, the dynamic mechanical analysis also showed the increase in glass transition temperature with increase in filler concentration due to the inter-tubular diffusion of EPDM inside the clay. It was also observed that with increasing filler concentration, the resistivity and dielectric strength decreases and moreover with increasing compatibilizer concentration the resistivity decreases due to better dispersion of filler helps to build conduction path. The morphological study also revealed that homogeneity of filler dispersion increases with increase in compatibilizer concentration.
This study was carried out to evaluate the microleakage of Class II cavities restored with various types of lining materials. Four types of composite resins (Esthet-X-Denstply, USA, FiltekTMZ350-3M ESPE, USA, Beautifil- Shofu, Japan and Solare P-GC, Japan) were used and the lining were the Fuji IXGP (GC, Japan), the Beautifil flow (Shofu, Japan), the FiltexTMZ350 flow (3M ESPE, USA) and the Esthet-X flow (Denstply, USA). All the specimens were thermocycled and immersed in 0.5% basic fuschin dye for 24 h. The microleakage was scored using the ISO microleakage scoring system. The data were entered using SPSS version 12.0 and analyzed using STATA software programme. This study showed that none of the materials used in this study was able to eliminate microleakage. However, it was shown that the glass ionomer cement was better in reducing the incident of microleakage at the cervical margin. Among the flowable composite resin, FiltexTMZ350 flow showed less microleakage at the cervical margin.
Hybrid composites of polypropylene (PP)/nanoclay (NC)/glass fiber (GF) were prepared byextrusion and injection molding. Molded specimens were analyzed by transmission electron microscopy (TEM), thermogravimetric analysis (TGA), tensile and flexural tests. TEM results revealed NC particle intercalation. TGA results showed that the incorporation of clay into the GF composite improves the thermal stability of the material. The initial thermal decomposition temperatures also shifted to higher values. Incorporation of GF into PP lowers the tensile strength of the binary composite, indicating poor fiber-matrix interfacial adhesion. However, introducing NC increased the strength of the ternary composites. Tensile modulus was enhanced with the incorporation of GF and further increased with an introduction of NC. Flexural strength and flexural modulus are both enhanced with an increase in GF and NC loading.
Miniaturisation of microchip capillary electrophoresis (MCE) is becoming an increasingly important research topic, particularly in areas related to micro total analysis systems or lab on a chip. One of the important features associated with the miniaturised MCE system is the portable power supply unit. In this work, a very low electric field MCE utilising an amperometric detection scheme was designed for use in DNA separation. The device was fabricated from a glass/polydimethylsiloxane hybrid engraved microchannel with platinum electrodes sputtered onto a glass substrate. Measurement was based on a three-electrode arrangement, and separation was achieved using a very low electric field of 12 V/cm and sample volume of 1.5 µl. The device was tested using two commercial DNA markers of different base pair sizes. The results are in agreement with conventional electrophoresis, but with improved resolution. The sensitivity consistently higher than 100 nA, and the separation time approximately 45 min, making this microchip an ideal tool for DNA analysis.
This paper investigates the effect of driving voltage on the attachment force of an electroadhesion actuator, as the existing literature on the saturation of the adhesive force at a higher electric field is incomplete. A new type of electroadhesion actuator using normally available materials, such as aluminum foil, PVC tape and a silicone rubber sheet used for keyboard protection, has been developed with a simple layered structure that is capable of developing adhesive force consistently. The developed actuator is subjected to the experiment for the evaluation of various test surfaces; aluminum, brick, ceramic, concrete and glass. The driving high voltage is varied in steps to determine the characteristics of the output holding force. Results show a quadratic relation between F (adhesion force) and V (driving voltage) within the 2 kV range. After this range, the F-V responses consistently show a saturation trend at high electric fields. Next, the concept of the leakage current that can occur in the dielectric material and the corona discharge through air has been introduced. Results show that the voltage level, which corresponds to the beginning of the supply current, matches well with the beginning of the force saturation. With the confirmation of this hypothesis, a working model for electroadhesion actuation is proposed. Based on the experimental results, it is proposed that such a kind of actuator can be driven within a range of optimum high voltage to remain electrically efficient. This practice is recommended for the future design, development and characterization of electroadhesion actuators for robotic applications.
The role of Escherichia coli H antigens in hydrophobicity and attachment to glass, Teflon and stainless steel (SS) surfaces was investigated through construction of fliC knockout mutants in E. coli O157:H7, O1:H7 and O157:H12. Loss of FliC(H12) in E. coli O157:H12 decreased attachment to glass, Teflon and stainless steel surfaces (p<0.05). Complementing E. coli O157:H12 ΔfliC(H12) with cloned wildtype (wt) fliC(H12) restored attachment to wt levels. The loss of FliCH7 in E. coli O157:H7 and O1:H7 did not always alter attachment (p>0.05), but complementation with cloned fliC(H12), as opposed to cloned fliCH7, significantly increased attachment for both strains compared with wt counterparts (p<0.05). Hydrophobicity determined using bacterial adherence to hydrocarbons and contact angle measurements differed with fliC expression but was not correlated to the attachment to materials included in this study. Purified FliC was used to functionalise silicone nitride atomic force microscopy probes, which were used to measure adhesion forces between FliC and substrates. Although no significant difference in adhesion force was observed between FliC(H12) and FliCH7 probes, differences in force curves suggest different mechanism of attachment for FliC(H12) compared with FliCH7. These results indicate that E. coli strains expressing flagellar H12 antigens have an increased ability to attach to certain abiotic surfaces compared with E. coli strains expressing H7 antigens.
Lithium potassium borate (LKB) glasses co-doped with TiO2 and MgO were prepared using the melt quenching technique. The glasses were cut into transparent chips and exposed to gamma rays of (60)Co to study their thermoluminescence (TL) properties. The TL glow curve of the Ti-doped material featured a single prominent peak at 230 °C. Additional incorporation of MgO as a co-activator enhanced the TL intensity threefold. LKB:Ti,Mg is a low-Z material (Z(eff)=8.89) with slow signal fading. Its radiation sensitivity is 12 times lower that the sensitivity of TLD-100. The dose response is linear at doses up to 10(3) Gy. The trap parameters, such as the kinetics order, activation energy, and frequency factor, which are related to the glow peak, were determined using TolAnal software.
The aim of this study was to assess the effects of four enamel preparation techniques on shear bond strength (SBS) of brackets bonded with a resin-modified glass ionomer cement (RMGIC). Adhesive Remnant Index (ARI) and enamel surface roughness (Ra) were also investigated after cement removal.
Recently, as a supplement of cement, the utilization of pozzolanic materials in cement and concrete manufacturing has increased significantly. This study investigates the scope to use pozzolanic wastes (slag, palm oil fuel ash and rice husk ash) as an alkali activated binder (AAB) that can be used as an alternative to cement. To activate these materials, sodium hydroxide solution was used at 1.0, 2.5 and 5.0 molar concentration added into the mortar, separately. The required solution was used to maintain the flow of mortar at 110% ± 5%. The consistency and setting time of the AAB-paste were determined. Mortar was tested for its flow, compressive strength, porosity, water absorption and thermal resistance (heating at 700 °C) and investigated by scanning electron microscopy. The experimental results reveal that AAB-mortar exhibits less flow than that of ordinary Portland cement (OPC). Surprisingly, AAB-mortars (with 2.5 molar solution) achieved a compressive strength of 34.3 MPa at 28 days, while OPC shows that of 43.9 MPa under the same conditions. Although water absorption and porosity of the AAB-mortar are slightly high, it shows excellent thermal resistance compared to OPC. Therefore, based on the test results, it can be concluded that in the presence of a chemical activator, the aforementioned pozzolans can be used as an alternative material for cement.
This paper reports on the direct ability of two positively charged organic polyelectrolytes (natural-based and synthetic) to reduce the atrazine concentration in water. The adsorption study was set up using multiple glass vessels with different polymer dosing levels followed by ultrafiltration with a 1 kDa membrane. The addition of polymers exhibited a capability in reducing the atrazine concentration up to a maximum of 60% in surface-to-volume ratio experiments. In the beginning, the theoretical L-type of the isotherm of Giles' classification was expected with an increase in the dosage of the polymer. However, in this study, the conventional type of isotherm was not observed. It was found that the adsorption of the cationic polymer on the negatively charged glass surface was necessary and influential for the removal of atrazine. Surface-to-volume ratio adsorption experiments were performed to elucidate the mechanisms and the polymer configuration. The glass surface area was determined to be a limiting parameter in the adsorption mechanism.
A radio frequency (RF) resonator using glass-reinforced epoxy material for C and X band is proposed in this paper. Microstrip line technology for RF over glass-reinforced epoxy material is analyzed. Coupling mechanism over RF material and parasitic coupling performance is explained utilizing even and odd mode impedance with relevant equivalent circuit. Babinet's principle is deployed to explicate the circular slot ground plane of the proposed resonator. The resonator is designed over four materials from different backgrounds which are glass-reinforced epoxy, polyester, gallium arsenide (GaAs), and rogers RO 4350B. Parametric studies and optimization algorithm are applied over the geometry of the microstrip resonator to achieve dual band response for C and X band. Resonator behaviors for different materials are concluded and compared for the same structure. The final design is fabricated over glass-reinforced epoxy material. The fabricated resonator shows a maximum directivity of 5.65 dBi and 6.62 dBi at 5.84 GHz and 8.16 GHz, respectively. The lowest resonance response is less than -20 dB for C band and -34 dB for X band. The resonator is prototyped using LPKF (S63) drilling machine to study the material behavior.
A multiband microstrip resonator is proposed in this study which is realized through a rectangular radiator with embedded symmetrical rectangular slots in it and a defected ground surface. The study is presented with detailed parametric analyses to understand the effect of various design parameters. The design and analyses are performed using the FIT based full-wave electromagnetic simulator CST microwave studio suite. With selected parameter values, the resonator showed a peak gain of 5.85 dBi at 5.2 GHz, 6.2 dBi at 8.3 GHz, 3.9 dBi at 9.5 GHz, 5.9 dBi at 12.2 GHz, and 4.7 dBi at 14.6 GHz. Meanwhile, the main lobe magnitude and the 3 dB angular beam width are 6.2 dBi and 86°, 5.9 dBi and 53.7°, 8.5 dBi and 43.9°, 8.6 dBi and 42.1°, and 4.7 dBi and 30.1°, respectively, at the resonant frequencies. The overall resonator has a compact dimension of 0.52λ × 0.52λ × 0.027λ at the lower resonant frequency. For practical validation, a lab prototype was built on a 1.6 mm thick epoxide woven glass fabric dielectric material which is measured using a vector network analyzer and within an anechoic chamber. The comparison between the simulated and measured results showed a very good understanding, which implies the practical suitability of the proposed multiband resonator design.
Poly(lactic acid) (PLA)-based nanocomposites filled with graphene nanoplatelets (xGnP) that contains epoxidized palm oil (EPO) as plasticizer were prepared by melt blending method. PLA was first plasticized by EPO to improve its flexibility and thereby overcome its problem of brittleness. Then, xGnP was incoporated into plasticized PLA to enhance its mechanical properties. Plasticized and nanofilled PLA nanocomposites (PLA/EPO/xGnP) showed improvement in the elongation at break by 3322% and 61% compared to pristine PLA and PLA/EPO, respectively. The use of EPO and xGnP increases the mobility of the polymeric chains, thereby improving the flexibility and plastic deformation of PLA. The nanocomposites also resulted in an increase of up to 26.5% in the tensile strength compared with PLA/EPO blend. XRD pattern showed the presence of peak around 26.5° in PLA/EPO/xGnP nanocomposites which corresponds to characteristic peak of graphene nanoplatelets. Plasticized PLA reinforced with xGnP showed that increasing the xGnP content triggers a substantial increase in thermal stability. Crystallinity of the nanocomposites as well as cold crystallization and melting temperature did not show any significant changes upon addition of xGnP. However, there was a significant decrease of glass transition temperature up to 0.3wt% of xGnP incorporation. The TEM micrograph of PLA/EPO/xGnP shows that the xGnP was uniformly dispersed in the PLA matrix and no obvious aggregation was observed.
The aim of this study is to investigate the effects of Palm Oil Clinker (POC) added as a stabilizer for improving the strength of peat. Cement and POC are added into peat up to 50% of the maximum dry unit weight. Treated peat achieved higher dry unit weight, almost 2.5 times as compared to untreated peat. Unconfined compressive strength (UCS) of treated peat is also investigated for soaked and unsoaked conditions. The results show that curing time improved the unconfined compressive strength of treated sample and increased by a factor of 20 and 11 for unsoaked and soaked conditions after 28 days of curing, respectively. The treated samples added with POC can be related to an increase in unconfined compressive strength for long time curing.
A comprehensive study on the spin-on-glass (SOG) based thin film insulating layer is presented. The SOG layer has been fabricated using simple MEMS technology which can play an important role as insulating layer of stack coupled microcoils. The fabrication process utilizes a simple, cost effective process technique as well as CMOS compatible resulting to a reproducible and good controlled process. It was observed that the spin speed and material preparation prior to the process affect to the thickness and surface quality of the layer. Through the annealing process at temperature 425oC in N2 atmospheric for 1 h, a 750 nm thin SOG layer with the surface roughness or the uniformity of about 1.5% can be achieved. Furthermore, the basic characteristics of the spiral coils, including the coupling characteristics and its parasitic capacitance were discussed in wide range of operating frequency. The results from this investigation showed a good prospect for the development of fully integrated planar magnetic field coupler and generator for sensing and actuating purposes.
A series of (Li20)x(B203)1-x has been synthesized with mole fraction x=0.10, 0.15,020,025 and 0.30 mol% using melt quenching method. The structure of the glass system was determined by FTIR and X-ray diffraction. The density and molar volume were determined and the density increases with Li20 content whereas molar volume decreases with Li20. Refractive index of glass samples were measured by ellipsometer. Refractive index increases with increase of Li20. The absorption spectra of the studied glass showed that position of fundamental absorption edge shifts to longer wavelength with Li20. Optical band gap varies from 0.10 to 222 eV and Urbach energy varies from 2.91 to 1.55 eV. The variation in optical band gap and Urbach energy were due to the variation in the glass structure.
In this paper, fabrication and investigation of organic pressure sensor based on AlICIVT-VO 2(3j7)ICu composite is reported. The active layer of the composite was deposited by drop-casting of the blend CN'T-VO 2 (3fl) on a glass substrate (with prefabricated copper (Cu) electrode). The thin film of the blend consists of carbon nanotube CNT, (2.55 wt. %) and vanadium oxide (VO 2 (3fl)) micropowder, (3 wt. %) in benzol (1 mL). The thickness of the composite was in the range of 20-40 ,um. It was found that the fabricated sensor was sensitive to pressure and showed good repeatability. The decrease in resistance of the sensor was observed by increasing the external uniaxial pressure up to 50 kNm-2 . The experimentally obtained results were compared with the simulated results and showed reasonable agreement with each other.
Structural and luminescence properties of borophosphate glasses with different modifier doped with transition metal ions have been investigated in this study. The glass sample from the series of xPb 30 4:0 .2Sb20 3:0.3B 20 3:(0 .5-x)P 20 5 and ySb 20 3:0 .2Pb 30 4:(0 .5-y)B 20 3:0 .3P 20 5where x 20 mol% and 0 y 0 .1 5mol% , respectively, were doped with 0.01 mol% of Fe 20 3 system have been prepared using the melt-quenching technique. The structural properties of samples had been studied using fourier transform infrared (FT-m) spectroscopy. The FT-IR study showed the network structure of the studied glasses based on the B 20 3-P 20 5host with the 5b203 and Pb203 modifiers. The results of FT-IR showed traces of B03 and B04 with the introduction of 5b203 and Pb203 modifiers. With the increasing content of B203 which replacing content of P205 in the glass network, the intensity of the borate band decreases and shifted to lower frequency. uv-Vis spectroscopy analysed the transition of Fe3+ from ground state to excited state in the ultraviolet spectral region. The photoluminescence of samples were studied using photoluminescence spectroscopy. The result of photoluminescence spectroscopy showed the effect of photoluminescence enhancement by doping Fe3+ as activator.