Displaying publications 1121 - 1140 of 2920 in total

Abstract:
Sort:
  1. Yusuf, Y., Juoi, J.M., Rosli, Z.M., Kwan, W.L., Mahamud, Z.
    MyJurnal
    Titanium alloy (e.g. Ti-6Al-4V) has an excellent combination of properties. However in many cases,
    the application is limited because of the poor wear property. In this work, a surface modification
    (plasma nitriding) is carried out to improve the surface properties of Ti-6Al-4V, as a treatment prior to a hardcoating deposition, leading to a duplex coating system. This is an effort to improve the surface and near surface property of Ti-6Al-4V. Plasma nitriding is performed utilizing microwave plasma method in 25% Ar- 75% N2 atmosphere at temperatures of 600°C and 700°C for different processing times (1, 3 and 5 hours). The phase and microstructure of plasma nitrided substrate were characterized by using X-ray diffraction (XRD) and Scanning electron microscopy (SEM). The plasma nitrided Ti-6Al-4V properties (surface roughness, surface hardness and case depth) were determined using profilometer and microhardness, respectively. Results obtained showed a significant increase on the surface hardness of Ti-6Al-4V. This is due to the formation of TiN and Ti2N phases in the form of compound layer. Besides, it shows that the diffusion of nitrogen into the Ti-6Al-4V substrate produces case depth up to 130 µm and this contributes to the improvement of the near surface hardness due to the changes in the microstructures. It was also found that the surface hardness and surface roughness increased with the increases in the process temperature and times.
    Matched MeSH terms: Temperature
  2. Tan, Y.P., Wong, Y.C.
    MyJurnal
    Bismuth chromium solid solutions, with a general formula Bi6-xCr2Oδ, where -1 ≤ x ≤ 2, were successfully synthesized via the conventional solid state method. The phases of the synthesized samples were determined by X-ray diffraction (XRD) analysis. The properties of single-phase compounds were characterized by using differential thermal analysis (DTA), thermal gravimetric analysis (TGA), AC impedance spectroscopy, and inductively coupled plasma-atomic emission spectroscopy (ICP-AES). The occurrence of phase transitions was confirmed by DTA and TGA, where a thermal event was observed by DTA at around 800oC. In addition, TGA studies also showed that there was a weight loss at around 800oC. Elemental analysis of Bi6Cr2O15 and its solid solutions by ICP-AES showed a good agreement between the expected value and the experimental value on the compositions, with no evidence of any systematic deviation from stoichiometric. Electrical properties of Bi6Cr2O15 and its solid solutions were investigated by using AC impedance spectroscopy from 300oC to 650oC. Ionic conductivity increased with the increasing temperature and bismuth content, and the best ionic conductivity was observed for Bi7Cr2O16.5. The activation energy (Ea) of Bi6Cr2O15 and its solid solutions were in the range of 1.22-1.32 eV.
    Matched MeSH terms: Temperature
  3. Jamilah, B., Abdulkadir Gedi, M., Suhaila, M., Md.Zaidul, I.S.
    MyJurnal
    The extraction of phenolics from Citrus hystrix leaf was carried out using supercritical fluid extraction and was optimized using response surface methodology (RSM). The effects of CO2 flow rate, extraction pressure and extraction temperature on yield, total phenolic content and diphenyl-picrylhydrazyl-IC50 were evaluated and compared with ethanol extraction. The extraction pressure was the most significant factor affecting the yield, TPC and DPPH-IC50 of the extracts, followed by CO2 flow rate and the extraction temperature. The optimum conditions of pressure, CO2 flow rate and temperature were at 267 bars, 18 g/min and 50°C, respectively. The yield, TPC and DPPH-IC50 obtained were 5.06%, 116.53 mg GAE/g extract and IC50 of 0.063 mg/ml, respectively. These values were not significantly different (p
    Matched MeSH terms: Temperature
  4. Ezlan Elias, Khairul Osman, Sharifa Abdul Aziz, Abdul Halim Mansar, Siti Fatimah Ibrahim, Jamaludin Mohamed
    MyJurnal
    Establishing time of death has been extensively studied for the last 30 years. Parameters that have been studied included body temperature, biochemistry of rigor mortis, putrefactive changes and entomology. Despite an extensive study in these parameters it was found that all of the parameters were very much dependent on external factors like changes in surrounding temperature and activities done prior to death. To solve this problem, we decided to monitor the mechanism that occurs during death. Until now, various researches have found that during the early stage of death, heart and perfusion to the cells will stop. This will cause the cells to start the death process. The death of the cell will occurs either through apoptosis or necrosis. During apoptosis the cells will switch on and off a few proteins in a sequence. Based on this understanding, a study was conducted to determine if area ratio of apoptosis: necrosis and apoptotic p53 and Bcl-2 markers can be used as a reliable postmortem interval marker (PMI). Sampling of the study had involved 100 dead human skins with a known PMI. All samples were obtained from forensic unit of Hospital Kuala Lumpur (UFHKL). Ratio of apoptosis: necrosis areas were determined using hematoxilin and eosin staining while apoptosis p53 and Bcl-2 markers were done using an apoptosis kit. All staining were then indexed and plotted against PMI data obtained from UFHKL. Results indicated that there were no significant correlations between ratio of apoptosis: necrosis area against PMI (p = 0.144). Whereas for both apoptotic markers p53 and Bcl-2 PMI had shown a significant correlation (p < 0.000 for both results). In conclusion, we suggest that p53 and Bcl-2 parameters should be studied further since it is very likely that it could be a good indicator for PMI.
    Matched MeSH terms: Temperature
  5. Kamarudin, K.S.N., Chieng, Y.Y., Hamdan, H., Mat, H.
    ASM Science Journal, 2010;4(1):29-40.
    MyJurnal
    Ordered microporous NaY zeolite and mesoporous copper oxide are high performance material as catalysts and adsorbents. The copper oxide-NaY zeolite modification in combination of their physicochemical properties could provide excellent opportunities for the creation of new gas adsorbents. In this study, modified NaY zeolite properties and methane adsorptive characteristics were investigated by dispersing copper oxide onto the NaY zeolite structure using the thermal dispersion method. The structures of the copper oxide modified zeolites were characterized by powder X-ray diffraction and Micromeritics ASAP 2000, while the methane adsorption characteristics were analyzed using a thermogravimetric analyzer. The results revealed that types of copper oxide, copper oxide loading concentration, calcination temperature and calcination time greatly affected the modified zeolite structure and gas methane adsorption characteristics.
    Matched MeSH terms: Temperature
  6. Rahman, M.M., Nor, S.S.M., Rahman, H.Y.
    ASM Science Journal, 2011;5(1):11-18.
    MyJurnal
    Warm compaction is an advanced manufacturing technique which consists of two consecutive steps, i.e. powder compaction at above ambient temperature and sintering in a controlled environment. Due to the relative movement between the powder mass and die wall as well as sliding among powder particles, frictional force is generated during the compaction stage. Admixed lubricant is used during the compaction step in order to minimize friction and hence improve the uniformity of the density of distribution inside the component. However, during the sintering process, trapped lubricant is often found to be burnt out hence leaving pores or voids which result in the lower strength of the final products. Warm compaction was initiated in the nineties, however not much information has been published about the effects of lubrication on the quality of the components produced through this route. Therefore, this paper presents the outcome of an experimental investigation about the effects of lubrication on manufacturing near-net shape components through the warm compaction route. Iron powder ASC 100.29 was mixed mechanically with zinc stearate to prepare the feedstock. Mixing time, weight percentage of lubricant content and compaction temperature were varied during green compact generation while sintering temperature, heating rate and holding time were manipulated during sintering. The relative densities and strengths of the final products were investigated at every compaction as well as sintering parameter. The results revealed that lubrication could provide significant effects at the compaction temperature of 180ºC while no significant effect of lubrication was observed during sintering. The suitable lubricant content was found to be 0.4 wt% and mixing time was around 30 min and the sintering temperature was around 990ºC.
    Matched MeSH terms: Temperature
  7. Ibrahim, M.N., Sarker, M.S.H., Ab. Aziz N., Mohd Salleh, P
    MyJurnal
    Field investigation on the operation of an industrial fluidized bed paddy dryer of 25 t/h capacity available in a processing complex of Padiberas Nasional Berhad (BERNAS) of Malaysia was carried out to assess its drying characteristics, energy consumption and quality of product during two paddy harvesting seasons. A grain drying simulation model was used to predict dryer performance which can be used as a basis for improving drying operations. For the first season (August-September), average drying rate was found to be 538 kg moisture/h to reduce moisture content (mc) from 36.98± 0.89% dry basis (db) to 27.58±0.79% (db) at 100-120°C of drying air temperature with a feed rate (capacity) of 7.75 t/h. In the second season (February-March), average drying rate was found to be 435 kg moisture/h to reduce mc from 28.14 ±0.68% (db) to 22.54 ± 0.69% (db) at 78-90°C drying air temperature with a feed rate of 9.5 t/h. The thermal and electrical energy consumptions were obtained as 7.57 and 0.97 MJ/kg water removed, respectively, for the first season, while 5.92 and 1.2 MJ/kg water removed for the second season. Higher head rice yield and whiteness and lower milling recovery were achieved during the first season than the second season at acceptable milling degree and transparency. Meanwhile, simulation results indicated that the dryer performed better in terms of increased drying capacity during the second than the first season; the dryer could be operated at 150°C to achieve almost double throughput capacity up to 20 t/h for the second season, while for the first season, high mc hindered the capacity to be at or below 7.75 t/h even when using higher a temperature of 160°C to reduce moisture to the desired final moisture of 24-25% (db). Proportion of slower vehicles based on users' opinion poll
    Matched MeSH terms: Temperature
  8. Siti Farhana Zakaria, Millington, Keith R.
    MyJurnal
    Polymers and organic materials that are exposed to sunlight undergo photooxidation, which leads to deterioration of their physical properties. To allow adequate performance under outdoor conditions, synthetic polymers require additives such as antioxidants and UV absorbers. A major problem with optimising polymer formulations to maximise their working life span is that accelerated weathering tests are empirical. The conditions differ significantly from real weathering situations, and samples require lengthy irradiation period. Degradation may not be apparent in the early stages of exposure, although this is when products such as hydroperoxides are formed which later cause acceleration of oxidation. A simple way of quantifying the number of free radicals presents in organic materials following exposure to light or heat is by measuring chemiluminescence (CL) emission. Most polymers emit CL when they undergo oxidative degradation, and it originates from the bimolecular reaction of macroperoxy radicals which creates an excited carbonyl.
    Matched MeSH terms: Hot Temperature
  9. Junaidah Jai, Wan Shabuddin Wan Ali
    Scientific Research Journal, 2011;8(2):49-70.
    MyJurnal
    Aluminium (Al) is a low cost, lightweight and corrosion resistant material, which corrodes when exposed to pitting agents. Palm olein exhibits characteristics, which indicate its suitability as a corrosion inhibitor. Tween 20, hexane and diethyl triamine were used as additives to Palm olein to form the inhibitor formulation POT2OHA. The inhibition efficiency (IE) and behaviour of the POT2OHA were determined using potentiodynamic polarization in which Al 6061 samples were immersed in a 1 M HC1 solution at 26, 50 and 70 °C in the presence of different POT2OHA concentrations: 0, 0.03, 0.07, 0.10, 0.13 and 0.17 M The IE increased with increasing POT2OHA concentration, but decreased with increasing temperature. The work presented indicates that POT2OHA is a mixed-type inhibitor capable of inhibiting both corrosive anodic and cathodic reactions. According to the Langmuir isotherm results POT2OHA adsorbs on the A16061 surface through semiphys iosorption and/or semi-chemisorption. The POT2OHA adsorption mechanism on Al 6061 takes through the protonation of micelles by the HC1 solution, whereby protonated micelles in the presence of chloride ions adsorb on both cathodic and anodic surface corrosion sites.
    Matched MeSH terms: Temperature
  10. Nurul lzza Taib, Norzuyanti Mohd Aris
    Scientific Research Journal, 2011;8(2):13-31.
    MyJurnal
    Anion clay hydrotalcite MgA1C0 3 with a Mg/A1 molar ratio of 3:1 was synthesized by co-precipitation at room temperature and pressure. The physicochemical properties were evaluated using Powder X-Ray Diffraction (PXRD), Fourier Transform Infrared (FTIR) spectroscopy and Thermogravimetric Analysis (TGA). The efficacy of anion clay hydrotalcite in the removal ofCcf- from aqueous solutions was investigated with respect to contact time, initial concentration, pH, adsorbent dosage and temperature. The Cd2- removal increased with the increased in contact time, adsorbent dosage, pH and initial concentration. Adsorption decreases with increasing initial concentration and temperature, for which the latter is indicative of an exothermic process. The equilibrium adsorption capacity of MgA1C0 3 was evaluated using linear Langmuir and Freundlich isotherms with respect to the separation factor, RL.
    Matched MeSH terms: Temperature
  11. Normah Ismail, Juliana Mahmod, Awatif Khairul Fatihin Mustafa Kamal
    MyJurnal
    In this study, Hydrolysate from angelwing clam (Pholas orientalis) was produced at 0, 1, 2 and 3 hrs and E/S ratio of 0.5 and 3% using alcalase where the pH and temperature were kept constant at pH 8.5 and 60°C, respectively. The hydrolysates were analysed for antioxidant and functional properties such as solubility, emulsifying properties and water and oil holding capacity. Degree of hydrolysis (DH), yield, functional and antioxidant properties were influenced by the hydrolysis time and E/S ratio. Higher enzyme concentration (E/S 3%) and longer hydrolysis time increased the DH. Yield was higher at E/S 3% but reduced with hydrolysis time. Longer hydrolysis time produced more soluble hydrolysate and higher metal chelating activity but lower in emulsifying properties and DPPH activity. Higher enzyme concentration resulted in increase only in solubility and metal chelating activity. This study revealed that enzymatic hydrolysis using alcalase should be performed at shorter hydrolysis time using intermediate concentration of enzyme (E/S between 0.5 to 3%) in order to produce angelwing clam hydrolysate with collectively good functional and antioxidant properties
    Matched MeSH terms: Temperature
  12. Zainab Shakir Radif, Aidy Ali, Khalina Abdan
    MyJurnal
    This study was conducted for the development of the green protection garments. For this purpose, laminate composite material was developed from Kevlar 29-ramie-unsaturated polyester resin. The aim of this study was to develop a solid body armour that meets the specific requirements of ballistic resistance. This composite is subjected to high impact loading. The target was shot using gas gun machine that is supported by camera hardware to capture the projectile speed. In order to achieve the goal of the research, several experiments were conducted with the aim to estimate the ballistic limit, maximum energy absorption, composite failure mode, life time rupture, target geometry, and environmental effect. The results of these experiments indicated that the maximum ballistic limit validated at impact speed is in the range of 250 m/s to 656.8 m/s for the second protection level. The targets are improved in term of the impact response with the increase in the relative humidity, i.e. the range of 50% ± 20%, whereas, reduction of resistance results in the increase of temperature. The range of temperatures was between 20oC and 70oC. A limited delamination was generated under multiple shots. Targets geometry plays a major role in increasing the impact response. Hence, the results present a high resistant impact for pairs from the panels with total thickness arrived to 15
    mm ± 3 mm. This body armour is one of the most economical armour products, in which common materials are used in its production, particularly to reduce the amount of Kevlar, and this could further lead to a decrease in its production cost. On the other hand, this armour meets the ballistic threats under 623 m/s of 15 mm ± 3 mm target thickness and 837.5 m/s of 25 mm ± 2.mm. Thus, the armour is equivalent to the third level of protective ballistic limits in the National Institute of Justice (NIJ) standards.
    Matched MeSH terms: Temperature
  13. Siregar, Januar Parlaungan, Mohd. Sapuan Salit, Mohd. Zaki Ab. Rahman, Khairul Zaman Hj. Mohd. Dahlan
    MyJurnal
    This paper studied the thermal behaviour of pineapple leaf fibre (PALF) reinforced high impact polystyrene (HIPS) composite. Thermogravimetric analysis (TGA) and differential scanning calorimetric (DSC) analysis were used to measure the thermal characteristic of HIPS/PALF composites. In particular, the TGA analysis was utilized to measure the degradation and decomposition of materials in neat polystyrene, pineapple fibre, and the composites. The measurements were carried out in the temperature of 25°C – 800°C, at a heating rate of 20°C min-1 and the nitrogen gas flow was 50 mL min-1. The temperature of the DSC analysis was programmed to be between 25°C – 300°C. The results from TGA analysis show that the addition of pineapple fibre has improved the thermal stability of the composites as compared to neat HIPS. In addition, the effects of compatibilising agent and surface modification of PALF with alkali treated were also determined and compared.
    Matched MeSH terms: Temperature
  14. Ujjal Kumar Ghosh, Chiu, Choon Hong, Jobrun Nandong, Shufeng, Shen
    MyJurnal
    In this paper, a mathematical model is developed based on mass and momentum balance for carbon dioxide absorption into aqueous ammonia solution. The model is simplified based on the assumption that the CO2 absorption into aqueous ammonia is a pseudo-first-order reaction. Laplace transform method is applied in order to solve the partial differential model equation. Finally, the CO2 molar flux is expressed as a function of partial pressure of CO2, concentration of aqueous ammonia, temperature and gas-liquid contact area. Variation of CO2 molar flux with partial pressure of CO2 and temperature is discussed and a comparison is performed with experimental data from literature. Variation of CO2 molar flux is also shown with gas-liquid contact area. The calculated flux from the model follows the same trend as that of the experimental data reported in literature and the accuracy is within the accepted limit. The mathematical model is very helpful to predict the CO2 molar flux as a function of partial pressure of CO2, concentration of aqueous ammonia, temperature and gas-liquid contact area.
    Matched MeSH terms: Temperature
  15. Krisnaiah, Duduku, Yan, Yan Farm, Awang Bono, Noor Maizura Ismail, Lee, Muei Chng
    MyJurnal
    Synthesis of carboxymethylcellulose (CMC) from natural cellulose is an important industrial process. The effect of process parameters on the synthesis process is important information for the efficiency improvement of production process. Most of the previous studies on the effect of process parameters
    on the synthesis of CMC are based on the One-Factor-At-Time (OFAT); therefore, in this work, the response surface methodology (RSM) was used. Here, the cellulose was converted to CMC through
    carboxymethylation process using a technique of William etherification in heterogeneous system. The process parameters studied include the solvent ratio, reaction temperature and reactant ratio (molar ratio of NaOH to SMCA). Meanwhile, the analysis and optimization of the responses of the process, degree of substitution (DS) and yield were also performed using the response surface methodology. The validity of the synthesis process was identified by the determination of CMC spectrum using the fast Fourier infrared spectrometer (FTIR). The analysis of the results shows that carboxymethylation is strongly affected by combination of process parameters studied. The results obtained also show that the optimum responses, degree of substitution (DS) is 0.87 and yield is 1.80, whereas the optimum process parameters, solvent ratio is 0.70v/v, reaction temperature at 56.03oC, and molar ratio of NaOH to SMCA at 1.00mol/mol. These findings conclude that the DS and yield of carboxymethylation of cellulose are strongly affected by the combination of the process parameters.
    Matched MeSH terms: Temperature
  16. Ariffin Abas, Abdul Halim Shaari, Zainal Abidin Talib, Zaidan Abdul Wahab
    MyJurnal
    The computer, together with Lab View software, can be used as an automatic data acquisition system. This project deals with the development of a computer interfacing technique for the study of Hall Effect and converting the existing automation system into a Web-based automation system. The drive board RS 217-3611 with PCI 6025E card and stepper motor RS191-8340 with a resolution of 0.1mm, was used to move a pair of permanent magnets backward and forward against the sample. The General Interface Bus (GPIB) card interfaces, together with digital nano voltmeter and Tesla meter using serial port RS232 interface, are used for measuring the potential difference and magnetic field strength respectively. Hall Effect measurement on copper (Cu) and tantalum (Ta) showed negative and positive sign Hall coefficient. Therefore, the system has electron and hole charge carriers respectively at room temperature. The parameters such as drift velocity, conductivity, mobility, Hall Coefficient and charge carrier concentration were also automatically displayed on the front panel of Lab View programming and compared with standard value. The Web-based automation system can be remotely controlled and monitored by users in remote locations using only their web browsers. In addition, video conferencing through Net Meeting has been used to provide audio and video feedback to the client.
    Matched MeSH terms: Temperature
  17. Zakiyah, L.K., Gui, M.M., Foo, R.S., Mohamed, A.R., Chai, S.P.
    ASM Science Journal, 2011;5(2):91-100.
    MyJurnal
    The functionalization of pristine CNTs is necessary for carbon nanotubes (CNTs) to be fully utilized, with the aim of increasing the nanotube reactivity and solubility in aqueous solutions. In this study, multi-walled carbon nanotubes (MWCNTs) were functionalized with a carboxylic group as this was an important step prior to application. The carboxylic group-functionalization was conducted through acid treatment, using sulphuric and nitric acids mixed at a ratio of 3:1 (v/v) and sonication for 30 min under different temperatures and time durations. The functionalization conditions of 50ºC x 5 h and 60ºC x 3 h were identified to be most suitable for introducing a carboxylic group onto the nanotube surfaces. The percentage of total weight loss due to the carboxylic group on the MWCNTs treated at 50ºC x 5 h and 60ºC x 3 h obtained from the thermogravimetric analysis was 13.26% and 13.76%, respectively. For both samples, peaks corresponding to the carboxylic group were identified in the FT-IR spectra. The changes in the morphology of the treated MWCNTs were also observed under SEM analysis.
    Matched MeSH terms: Temperature
  18. Mohd. Azam Mohd. Adnan, Cheong, K.Y., Hutagalung, Sabar D.
    MyJurnal
    Silicon nanowires were synthesized on Si substrates (111) via thermal evaporation using AuPd thin layer catalyst. Pre cleaned of Si wafer was used as a substrate to assemble the nanostructure products. In this work, the effect of growth temperature that ranging from 800 to 1000°C on the formation of silicon nanowires studied extensively. X-ray diffraction and field emission scanning electron microscope were employed to characterize the structures and morphology of nanowires. Vertical aligned silicon nanowires have been successfully grown on Si substrates at 900 and 1000°C. At 1100°C, the high aspect ratio of silicon nanowires can be produced but the formation density is low. The presence of AuPd catalyst on the tip of nanowires, it is expected that VLS is the most suitable to explain the growth mechanism of obtained SiNWs. The crystalline structure of SiNWs was proved by XRD data.
    Matched MeSH terms: Temperature
  19. Noraishah Othman, Muhd Noor Md Yunus, Siti Kartom Kamarudin, Abd Halim Shamsuddin, Siti Rozaimah, Zahirah Yaakob
    MyJurnal
    Production of carbon dioxide from degraded woods especially Karas or Aquilariella Malaccensis using integrated pyrolysis-combustion is important for radiocarbon dating application. The effects of pyrolysis temperatures (300-400 0 C), retention times (20-35 minutes) and flow rates of argon (400- 1000 ml/min) on the production of carbon dioxide were studied. The experiments were arranged according to a 2 3 response surface central composite statistical design (CSD). This response surface methodology (RSM) was used to assess factor interactions and empirical models regarding carbon dioxide yield. The optimized yield of carbon dioxide was 82.57% for Karas and the optimum reaction conditions are 300 0 C of pyrolysis temperature, 20 minutes retention time and 982ml/min flow rates of argon. Scanning electron microscope (SEM) and X-ray Diffraction (XRD) were conducted to assess the morphological characteristics of the woods and to look at the potential crystalline structure produced after the process took place, respectively.
    Matched MeSH terms: Temperature
  20. Noorashikin Md Saleh, Sanagi, M. Marsin
    MyJurnal
    A Pressurized Liquid Extraction (PLE) method was developed by using conventional High Performance
    Liquid Chromatography (HPLC). It was found that all of the PAHs have been successfully extracted with dichloromethane-acetone with high percentage recovery. A high temperature of 180°C gave the highest recovery for fluoranthene (94.4%). Meanwhile, fluorene showed the highest recovery at 150 bar, with 94.6% recovery. It is noted that there is no significant day-to-day difference in the efficiency of the developed method, with the R.S.D. values averaging at 0.02. The optimized conditions applied to the soil samples were analysed using the High Temperature High Performance Liquid Chromatography (HT-HPLC) with chromatographic conditions: Octadecylsilyl-silica (ODSsilica) column (100 mm × 4.6 mm I.D.); mobile phase acetonitrile:water 40:60 (v/v); flow rate 2.5 mL/min; temperature 70°C; UV absorbance 254 nm; injection volume 5µL.
    Matched MeSH terms: Temperature
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links