MyMedR

Displaying publications 141 - 160 of 215 in total

Abstract:

Sort:

Package plant of extended aeration membrane bioreactors: a study on aeration intensity and biofouling control

Ujang Z, Ng SS, Nagaoka H

Water Sci Technol, 2005;51(10):335-42.
PMID: 16104438

Biofouling control is important for effective process of membrane bioreactor (MBR). In this study, phenomena of biofouling for immersed type extended aeration MBR with two different anti-fouling aeration intensities were studied through a laboratory set up. The objectives of this study were (a) to observe biofouling phenomena of MBR that operates under different anti-fouling bubbling intensity, and simultaneously monitors performance of the MBR in organic carbon and nutrients removal; (b) to compare effectiveness of detergent and detergent-enzyme cleaning solutions in recovering biofouled membranes that operated in the extended aeration MBR. For MBR, which operated under continuous anti-fouling aeration, deposition and accumulation of suspended biomass on membrane surface were prohibited. However, flux loss was inescapable that biofilm layer was the main problem. Membrane cleaning was successfully carried out with detergent-enzyme mixture solutions and its effectiveness was compared with result from cleaning with just detergent solution.

Matched MeSH terms: Waste Disposal, Fluid/methods*
Parenteral cytotoxic drug wastage at a tertiary hospital in Kuala Lumpur: How much and why?

Ang ZY, Cheah KY, Abdullah NB, Samsuri SB, Lee SH, Yem AW, et al.

J Oncol Pharm Pract, 2020 Sep;26(6):1306-1317.
PMID: 31810422 DOI: 10.1177/1078155219891209

PURPOSE: To identify the cost and reasons of returned parenteral chemotherapy regimens at a tertiary hospital in Kuala Lumpur, Malaysia.
METHODS: Data were retrospectively extracted from all the Chemotherapy Return Forms in 2016, which is a compulsory documentation accompanying each return of parenteral chemotherapy regimen. The following data were extracted: patient's diagnosis, gender, location of treatment (i.e. ward/daycare clinic), start date of chemotherapy regimen, type of cytotoxic drug returned, dose of cytotoxic drug returned, number of cytotoxic drug preparations returned and reason for return as well as whether the returned cytotoxic drug preparations could be re-dispensed. The cost of wastage was calculated based on the cost per mg (or per unit) of the particular returned cytotoxic drug.
RESULTS: One hundred and fifty-nine cases of returned chemotherapy regimen comprising of 231 parenteral cytotoxic drug preparations were analysed. The total cost of returned chemotherapy regimen for 2016 was €3632, with €756 (20.8%) worth of chemotherapy regimens returned due to preventable reasons and €2876 (79.2%) worth of chemotherapy regimens returned due to non-preventable reasons. Approximately 50% of cases returned chemotherapy regimen were due to deterioration of patient's clinical condition and another 24.5% of cases of returned chemotherapy regimen were attributed to adverse drug reactions.
CONCLUSION: Wastage associated to non-preventable reasons such as adverse drug reactions and preventable causes like refusal of patients can be further reduced by using newer healthcare innovations and establishment of written institutional protocols or standard operating procedures as references for in-charge healthcare personnel when cytotoxic drug-related issues occur. Adoption of cost-saving strategies that have been proven by studies could further improve current cost containment strategies.

Matched MeSH terms: Waste Disposal, Fluid/methods*
Performance of aerobic granular sludge at variable circulation rate in anaerobic-aerobic conditions

Harun H, Anuar AN, Ujang Z, Rosman NH, Othman I

Water Sci Technol, 2014;69(11):2252-7.
PMID: 24901619 DOI: 10.2166/wst.2014.156

Aerobic granular sludge (AGS) has been applied to treat a broad range of industrial and municipal wastewater. AGS can be developed in a sequencing batch reactor (SBR) with alternating anaerobic-aerobic conditions. To provide anaerobic conditions, the mixed liquor is allowed to circulate in the reactor without air supply. The circulation flow rate of mixed liquor in anaerobic condition is the most important parameter of operation in the anaerobic-AGS processes. Therefore, this study investigates the effect of circulation rate on the performance of the SBR with AGS. Two identical reactors namely R1 and R2 were operated using fermented soy sauce wastewater at circulation rate of 14.4 and 36.0 l/h, respectively. During the anaerobic conditions, the wastewater was pumped out from the upper part of the reactor and circulated back into the bottom of the reactor for 230 min. A compact and dense AGS was observed in both reactors with a similar diameter of 2.0 mm in average, although different circulation rates were adopted. The best reactor performance was achieved in R2 with chemical oxygen demand removal rate of 89%, 90% total phosphorus removal, 79% ammonia removal, 10.1 g/l of mixed liquor suspended solids and a sludge volume index of 25 ml/g.

Matched MeSH terms: Waste Disposal, Fluid/methods*
Performance of cellulose acetate - polyethersulphone blend membrane prepared using microwave heating for palm oil mill effluent treatment

Idris A, Ahmed I, Jye HW

Water Sci Technol, 2007;56(8):169-77.
PMID: 17978445

The objective of this research is to investigate the performance of blend cellulose acetate (CA)-polyethersulphone (PES) membranes prepared using microwave heating (MWH) techniques and then compare it with blend CA-PES membranes prepared using conventional heating (CH) methods using bovine serum albumin solution. The superior membranes were then used in the treatment of palm oil mill effluent (POME). Various blends of CA-PES have been blended with PES in the range of 1-5 wt%. This distinctive series of dope formulations of blend CA/PES and pure CA was prepared using N, N-dimethylformamide (DMF) as solvent. The dope solution was prepared by MW heating for 5 min at a high pulse and the membranes were prepared by phase inversion method. The performances of these membranes were evaluated in terms of pure water and permeate flux, percentage removal of total suspended solids (TSS), chemical oxygen demand (COD) and biochemical oxygen demand (BOD). The results indicate that blend membranes prepared using the microwave technique is far more superior compared to that prepared using CH. Blend membranes with 19% CA, 1-3% PES and 80% of DMF solvent were found to be the best membrane formulation.

Matched MeSH terms: Waste Disposal, Fluid/methods
Pharmaceutical waste and antimicrobial resistance

Ahmad A, Patel I, Khan MU, Babar ZU

Lancet Infect Dis, 2017 06;17(6):578-579.
PMID: 28555576 DOI: 10.1016/S1473-3099(17)30268-2
Matched MeSH terms: Waste Disposal, Fluid/methods
Phosphorus removal using nanofiltration membranes

Leo CP, Chai WK, Mohammad AW, Qi Y, Hoedley AF, Chai SP

Water Sci Technol, 2011;64(1):199-205.
PMID: 22053475

A high concentration of phosphorus in wastewater may lead to excessive algae growth and deoxygenation of the water. In this work, nanofiltration (NF) of phosphorus-rich solutions is studied in order to investigate its potential in removing and recycling phosphorus. Wastewater samples from a pulp and paper plant were first analyzed. Commercial membranes (DK5, MPF34, NF90, NF270, NF200) were characterized and tested in permeability and phosphorus removal experiments. NF90 membranes offer the highest rejection of phosphorus; a rejection of more than 70% phosphorus was achieved for a feed containing 2.5 g/L of phosphorus at a pH <2. Additionally, NF90, NF200 and NF270 membranes show higher permeability than DK5 and MPF34 membranes. The separation performance of NF90 is slightly affected by phosphorus concentration and pressure, which may be due to concentration polarization and fouling. By adjusting the pH to 2 or adding sulfuric acid, the separation performance of NF90 was improved in removing phosphorus. However, the presence of acetic acid significantly impairs the rejection of phosphorus.

Matched MeSH terms: Waste Disposal, Fluid/methods*
Phytoremediation of palm oil mill secondary effluent (POMSE) by Chrysopogon zizanioides (L.) using artificial neural networks

Darajeh N, Idris A, Fard Masoumi HR, Nourani A, Truong P, Rezania S

Int J Phytoremediation, 2017 May 04;19(5):413-424.
PMID: 27748626 DOI: 10.1080/15226514.2016.1244159

Artificial neural networks (ANNs) have been widely used to solve the problems because of their reliable, robust, and salient characteristics in capturing the nonlinear relationships between variables in complex systems. In this study, ANN was applied for modeling of Chemical Oxygen Demand (COD) and biodegradable organic matter (BOD) removal from palm oil mill secondary effluent (POMSE) by vetiver system. The independent variable, including POMSE concentration, vetiver slips density, and removal time, has been considered as input parameters to optimize the network, while the removal percentage of COD and BOD were selected as output. To determine the number of hidden layer nodes, the root mean squared error of testing set was minimized, and the topologies of the algorithms were compared by coefficient of determination and absolute average deviation. The comparison indicated that the quick propagation (QP) algorithm had minimum root mean squared error and absolute average deviation, and maximum coefficient of determination. The importance values of the variables was included vetiver slips density with 42.41%, time with 29.8%, and the POMSE concentration with 27.79%, which showed none of them, is negligible. Results show that the ANN has great potential ability in prediction of COD and BOD removal from POMSE with residual standard error (RSE) of less than 0.45%.

Matched MeSH terms: Waste Disposal, Fluid/methods*
Pilot-scale removal of chromium from industrial wastewater using the ChromeBac system

Ahmad WA, Zakaria ZA, Khasim AR, Alias MA, Ismail SM

Bioresour Technol, 2010 Jun;101(12):4371-8.
PMID: 20185301 DOI: 10.1016/j.biortech.2010.01.106

The enzymatic reduction of Cr(VI) to Cr(III) by Cr(VI) resistant bacteria followed by chemical precipitation constitutes the ChromeBac system. Acinetobacter haemolyticus was immobilized onto carrier material inside a 0.2m(3) bioreactor. Neutralized electroplating wastewater with Cr(VI) concentration of 17-81 mg L(-1) was fed into the bioreactor (0.11-0.33 m(3)h(-1)). Complete Cr(VI) reduction to Cr(III) was obtained immediately after the start of bioreactor operation. Together with the flocculation, coagulation and filtration, outflow concentration of less than 0.02 mg Cr(VI)L(-1) and 1mg total CrL(-1) were always obtained. Performance of the bioreactor was not affected by fluctuations in pH (6.2-8.4), Cr(VI) (17-81 mg L(-1)), nutrient (liquid pineapple waste, 1-20%v/v) and temperature (30-38 degrees C). Standby periods of up to 10 days can be tolerated without loss in activity. A robust yet effective biotechnology to remove chromium from wastewater is thus demonstrated.

Matched MeSH terms: Waste Disposal, Fluid/methods*
Pollutant in palm oil production process

Hosseini SE, Abdul Wahid M

J Air Waste Manag Assoc, 2015 Jul;65(7):773-81.
PMID: 26079550 DOI: 10.1080/10962247.2013.873092

Palm oil mill effluent (POME) is a by-product of the palm industry and it releases large amounts of greenhouse gases (GHGs). Water systems are also contaminated by POME if it is released into nonstandard ponds or rivers where it endangers the lives of fish and water fowl. In this paper, the environmental bottlenecks faced by palm oil production were investigated by analyzing the data collected from wet extraction palm oil mills (POMs) located in Malaysia. Strategies for reducing pollution and technologies for GHG reduction from the wet extraction POMs were also proposed. Average GHG emissions produced from processing 1 ton of crude palm oil (CPO) was 1100 kg CO2eq. This amount can be reduced to 200 kg CO2eq by capturing biogases. The amount of GHG emissions from open ponds could be decreased from 225 to 25 kg CO2eq/MT CPO by covering the ponds. Installation of biogas capturing system can decrease the average of chemical oxygen demand (COD) to about 17,100 mg/L and stabilizing ponds in the final step could decrease COD to 5220 mg/L. Using a biogas capturing system allows for the reduction of COD by 80% and simultaneously using a biogas capturing system and by stabilizing ponds can mitigate COD by 96%. Other ways to reduce the pollution caused by POME, including the installation of wet scrubber vessels and increasing the performance of biogas recovery and biogas upgrading systems, are studied in this paper.

Matched MeSH terms: Waste Disposal, Fluid/methods
Post-treatment of palm oil mill effluent (POME) using combined persulphate with hydrogen peroxide (S2O8(2-)/H2O2) oxidation

Lin CK, Bashir MJ, Abu Amr SS, Sim LC

Water Sci Technol, 2016 Dec;74(11):2675-2682.
PMID: 27973372

The aim of the current study is to evaluate the effectiveness of combined persulphate with hydrogen peroxide (S2O8(2-)/H2O2) oxidation as a post-treatment of biologically treated palm oil mill effluent (POME) for the first time in the literature. The removal efficiencies of chemical oxygen demand (COD), ammoniacal nitrogen (NH3-N), and suspended solids (SS) were 36.8%, 47.6%, and 90.6%, respectively, by S2O8(2-) oxidation alone under certain operation conditions (i.e., S2O8(2-) = 0.82 g, pH 11, and contact time 20 min). Nevertheless, the combined process (S2O8(2-)/H2O2) achieved 75.8% and 87.1% removals of NH3-N and SS, respectively, under 2.45/1.63 g/g H2O2/S2O8(2-), pH 11, and 20 min oxidation. Moreover, 56.9% of COD was removed at pH 8.4.

Matched MeSH terms: Waste Disposal, Fluid/methods
Potential non-phytopathogenic filamentous fungi for bioconversion of domestic wastewater sludge

Molla AH, Fakhru'l-Razi A, Hanafi MM, Abd-Aziz S, Alam MZ

J Environ Sci Health A Tox Hazard Subst Environ Eng, 2002 Sep;37(8):1495-507.
PMID: 12369641

Ten filamentous fungi adapted to domestic wastewater sludge (DWS) were further studied to evaluate their potential in terms of adaptation to higher sludge supplemented growing media and phytopathogenicity (induction of diseases to plants) to three germinating crop (Corn: Zea mays, Mung bean: Phaseolus aureus and Mustard: Brassica napus) seeds. The performances of the fungi in seed germination were evaluated based on percent germination index (GI) and infected/spotted seeds on direct fungal biomass (FBM) and fungal metabolite (FM). Significantly the highest biomass production was achieved with RW-P1 512 and Penicillium corylophilum (WW-P1003) at the highest (25%) sludge supplemented growing media that implied its excellent potentiality of adaptation and multiplication to domestic wastewater sludge. Significantly encouraging results of percent GI and spotted/infected seedlings were observed in FM than FBM by all fungi except the strain Aspergillus niger. A. niger gave the poorest percent of GI (24.30, 26.98 and 00.00%) and the highest percent of infected/spotted seeds (70, 100, and 100%) using FBM for corn, mung bean and mustard, respectively. On the other hand, comparatively the highest percent of GI (107.99, 106.25 and 117.67%) and the lowest percent of spotted/infected seedlings (3.3, 3.3 and 3.3%) were achieved with the isolate RW-P1 512 using FM. In FBM, the superior results of percent GI (86.61, 95.92 and 83.87%) and spotted/infected seedlings (3.3, 63.3 and 43.3%) were obtained by A. versicolor. Several crop seeds were responded differently for different fungal treatments. Hundred percent infected/spotted seeds in FM were recorded only for mustard with Trichoderma family that implied its strong sensitiveness to its metabolites.

Matched MeSH terms: Waste Disposal, Fluid/methods*
Potential of nanofiltration and low pressure reverse osmosis in the removal of phosphorus for aquaculture

Leo CP, Yahya MZ, Kamal SN, Ahmad AL, Mohammad AW

Water Sci Technol, 2013;67(4):831-7.
PMID: 23306262 DOI: 10.2166/wst.2012.625

Aquaculture activities in developing countries have raised deep concern about nutrient pollution, especially excess phosphorus in wastewater, which leads to eutrophication. NF, NF90, NF450 and XLE membranes were studied to forecast the potential of nanofiltration and low pressure reverse osmosis in the removal of phosphorus from aquaculture wastewater. Cross-sectional morphology, water contact angle, water permeability and zeta potential of these membranes were first examined. Membrane with higher porosity and greater hydrophilicity showed better permeability. Membrane samples also commonly exhibited high zeta potential value in the polyphosphate-rich solution. All the selected membranes removed more than 90% of polyphosphate from the concentrated feed (75 mg/L) at 12 bar. The separation performance of XLE membrane was well maintained at 94.6% even at low pressure. At low feed concentration, more than 70.0% of phosphorus rejection was achieved using XLE membrane. The formation of intermolecular bonds between polyphosphate and the acquired membranes probably had improved the removal of polyphosphate at high feed concentration. XLE membrane was further tested and its rejection of polyphosphate reduced with the decline of pH and the addition of ammonium nitrate.

Matched MeSH terms: Waste Disposal, Fluid/methods*
Powdered ZELIAC augmented sequencing batch reactors (SBR) process for co-treatment of landfill leachate and domestic wastewater

Mojiri A, Aziz HA, Zaman NQ, Aziz SQ, Zahed MA

J Environ Manage, 2014 Jun 15;139:1-14.
PMID: 24662109 DOI: 10.1016/j.jenvman.2014.02.017

Sequencing batch reactor (SBR) is one of the various methods of biological treatments used for treating wastewater and landfill leachate. This study investigated the treatment of landfill leachate and domestic wastewater by adding a new adsorbent (powdered ZELIAC; PZ) to the SBR technique. ZELIAC consists of zeolite, activated carbon, lime stone, rice husk ash, and Portland cement. The response surface methodology and central composite design were used to elucidate the nature of the response surface in the experimental design and describe the optimum conditions of the independent variables, including aeration rate (L/min), contact time (h), and ratio of leachate to wastewater mixture (%; v/v), as well as their responses (dependent variables). Appropriate conditions of operating variables were also optimized to predict the best value of responses. To perform an adequate analysis of the aerobic process, four dependent parameters, namely, chemical oxygen demand (COD), color, ammonia-nitrogen (NH3-N), and phenols, were measured as responses. The results indicated that the PZ-SBR showed higher performance in removing certain pollutants compared with SBR. Given the optimal conditions of aeration rate (1.74 L/min), leachate to wastewater ratio (20%), and contact time (10.31 h) for the PZ-SBR, the removal efficiencies for color, NH3-N, COD, and phenols were 84.11%, 99.01%, 72.84%, and 61.32%, respectively.

Matched MeSH terms: Waste Disposal, Fluid/methods*
Prediction analysis of effluent removal in a septic sludge treatment plant: a biomimetics engineering approach

Chun TS, Malek MA, Ismail AR

Environ Sci Process Impacts, 2014 Sep 20;16(9):2208-14.
PMID: 25005632 DOI: 10.1039/c4em00282b

Effluent discharge from septic tanks is affecting the environment in developing countries. The most challenging issue facing these countries is the cost of inadequate sanitation, which includes significant economic, social, and environmental burdens. Although most sanitation facilities are evaluated based on their immediate costs and benefits, their long-term performance should also be investigated. In this study, effluent quality-namely, the biological oxygen demand (BOD), chemical oxygen demand (COD), and total suspended solid (TSS)-was assessed using a biomimetics engineering approach. A novel immune network algorithm (INA) approach was applied to a septic sludge treatment plant (SSTP) for effluent-removal predictive modelling. The Matang SSTP in the city of Kuching, Sarawak, on the island of Borneo, was selected as a case study. Monthly effluent discharges from 2007 to 2011 were used for training, validating, and testing purposes using MATLAB 7.10. The results showed that the BOD effluent-discharge prediction was less than 50% of the specified standard after the 97(th) month of operation. The COD and TSS effluent removals were simulated at the 85(th) and the 121(st) months, respectively. The study proved that the proposed INA-based SSTP model could be used to achieve an effective SSTP assessment and management technique.

Matched MeSH terms: Waste Disposal, Fluid/methods*
Preparation, characterization, and dye removal study of activated carbon prepared from palm kernel shell

García JR, Sedran U, Zaini MAA, Zakaria ZA

Environ Sci Pollut Res Int, 2018 Feb;25(6):5076-5085.
PMID: 28391459 DOI: 10.1007/s11356-017-8975-8

Palm oil mill wastes (palm kernel shell (PKS)) were used to prepare activated carbons, which were tested in the removal of colorants from water. The adsorbents were prepared by 1-h impregnation of PKS with ZnCl2 as the activating agent (PKS:ZnCl2 mass ratios of 1:1 and 2:1), followed by carbonization in autogenous atmosphere at 500 and 550 °C during 1 h. The characterization of the activated carbons included textural properties (porosity), surface chemistry (functional groups), and surface morphology. The dye removal performance of the different activated carbons was investigated by means of the uptake of methylene blue (MB) in solutions with various initial concentrations (25-400 mg/L of MB) at 30 °C, using a 0.05-g carbon/50-mL solution relationship. The sample prepared with 1:1 PKS:ZnCl2 and carbonized at 550 °C showed the highest MB adsorption capacity (maximum uptake at the equilibrium, q max = 225.3 mg MB / g adsorbent), resulting from its elevated specific surface area (BET, 1058 m2/g) and microporosity (micropore surface area, 721 m2/g). The kinetic experiments showed that removals over 90% of the equilibrium adsorptions were achieved after 4-h contact time in all the cases. The study showed that palm oil mill waste biomass could be used in the preparation of adsorbents efficient in the removal of colorants in wastewaters.

Matched MeSH terms: Waste Disposal, Fluid/methods*
Production and recovery of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) from biodiesel liquid waste (BLW)

Martla M, Umsakul K, Sudesh K

J Basic Microbiol, 2018 Nov;58(11):977-986.
PMID: 30095175 DOI: 10.1002/jobm.201800279

Polyhydroxyalkanoates (PHAs) has been paid great attention because of its useful thermoplastic properties and complete degradation in various natural environments. But, at industrial level, the successful commercialization of PHAs is limited by the high production cost due to the expensive carbon source and recovery processes. Pseudomonas mendocina PSU cultured for 72 h in mineral salts medium (MSM) containing 2% (v/v) biodiesel liquid waste (BLW) produced 79.7 wt% poly(3-hydroxybutyrate) (PHB) at 72 h. In addition, this strain produced 43.6 wt% poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) with 8.6 HV mol% at 60 h when added with 0.3% sodium propionate. The synthesized intracellular PHA granules were recovered and purified by the recently reported biological method using mealworms. The weight average molecular weight (Mw ) and number average molecular weight (Mn ) of the biologically extracted PHA were higher than that from the chloroform extraction with comparable melting temperature (Tm ) and high purity. This study has successfully established a low-cost process to synthesize PHAs from BLW and subsequently confirmed the ability of mealworms to extract PHAs from various kinds of bacterial cells.

Matched MeSH terms: Waste Disposal, Fluid/methods*
Production of bioethanol by direct bioconversion of oil-palm industrial effluent in a stirred-tank bioreactor

Alam MZ, Kabbashi NA, Hussin SN

J Ind Microbiol Biotechnol, 2009 Jun;36(6):801-8.
PMID: 19294441 DOI: 10.1007/s10295-009-0554-7

The purpose of this study was to evaluate the feasibility of producing bioethanol from palm-oil mill effluent generated by the oil-palm industries through direct bioconversion process. The bioethanol production was carried out through the treatment of compatible mixed cultures such as Thrichoderma harzianum, Phanerochaete chrysosporium, Mucor hiemalis, and yeast, Saccharomyces cerevisiae. Simultaneous inoculation of T. harzianum and S. cerevisiae was found to be the mixed culture that yielded the highest ethanol production (4% v/v or 31.6 g/l). Statistical optimization was carried out to determine the operating conditions of the stirred-tank bioreactor for maximum bioethanol production by a two-level fractional factorial design with a single central point. The factors involved were oxygen saturation level (pO(2)%), temperature, and pH. A polynomial regression model was developed using the experimental data including the linear, quadratic, and interaction effects. Statistical analysis showed that the maximum ethanol production of 4.6% (v/v) or 36.3 g/l was achieved at a temperature of 32 degrees C, pH of 6, and pO(2) of 30%. The results of the model validation test under the developed optimum process conditions indicated that the maximum production was increased from 4.6% (v/v) to 6.5% (v/v) or 51.3 g/l with 89.1% chemical-oxygen-demand removal.

Matched MeSH terms: Waste Disposal, Fluid/methods*
Fulltext Prospective Application of Palm Oil Mill Boiler Ash as a Biosorbent: Effect of Microwave Irradiation and Palm Oil Mill Effluent Decolorization by Adsorption

Hamzah MH, Ahmad Asri MF, Che Man H, Mohammed A

Int J Environ Res Public Health, 2019 09 17;16(18).
PMID: 31533308 DOI: 10.3390/ijerph16183453

Common conventional biological treatment methods fail to decolorize palm oil mill effluent (POME). The present study focused on using the abundant palm oil mill boiler (POMB) ashes for POME decolorization. The POMB ashes were subjected to microwave irradiation and chemical treatment using H2SO4. The resultant adsorbents were characterized using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and Brunauer-Emmett-Teller (BET) analyses. The adsorption efficiency was evaluated at various pH levels (2-8.5), adsorption dosages (3-15 g) in 200 mL, and contact times (1-5 h). The microwave-irradiated POMB-retained ash recorded the highest color removal of 92.31%, for which the best conditions were pH 2, 15 g adsorbent dosage in 200 mL, and 5 h of contact time. At these best treatment conditions, the color concentration of the treated effluent was analyzed using the method proposed by the American Dye Manufacturers Institute (ADMI). The color concentration was 19.20 ADMI, which complies with the Malaysia discharge standard class A. The Freundlich isotherm model better fit the experimental data and had a high R2 of 0.9740. Based on these results, it can be deduced that microwave-irradiated POMB-retained ash has potential applications for POME decolorization via a biosorption process.

Matched MeSH terms: Waste Disposal, Fluid/methods
Quality and first flush analysis of stormwater runoff from a tropical commercial catchment

Chow MF, Yusop Z, Mohamed M

Water Sci Technol, 2011;63(6):1211-6.
PMID: 21436558 DOI: 10.2166/wst.2011.360

This paper examines the storm runoff quality from a commercial area in south Johor, Malaysia. Six storm events with a total of 68 storm runoff samples were analyzed. Event Mean Concentration (EMC) for all constituents analysed showed large inter-event variation. Site mean concentrations (SMC) for total suspended solids (TSS), oil and grease (O&G), biochemical oxygen demand (BOD), chemical oxygen demand (COD), nitrate-nitrogen (NO(3)-N), nitrite-nitrogen (NO(2)-N), ammonia-nitrogen (NH(3)-N), total phosphorus (Total P) and Soluble P are 261, 4.31, 74, 192, 1.5, 0.006, 1.9, 1.12 and 0.38 mg/L, respectively. The SMCs at the studied site are higher than those reported in many urban catchments. The mean baseflow concentrations were higher than the EMCs for COD, Soluble P, NH(3)-N, NO(3)-N, Total P and NO(2)-N. However, the reverse was observed for TSS and O&G. All pollutants showed the occurrence of first flush phenomenon with the highest strength was observed for TSS, COD and NH(3)-N.

Matched MeSH terms: Waste Disposal, Fluid/methods*
Raw landfill leachate treatment using an electrocoagulation process with a novel rotating electrode reactor

Naje AS, Ajeel MA, Ali IM, Al-Zubaidi HAM, Alaba PA

Water Sci Technol, 2019 Aug;80(3):458-465.
PMID: 31596257 DOI: 10.2166/wst.2019.289

In this work, landfill leachate treatment by electrocoagulation process with a novel rotating anode reactor was studied. The influence of rotating anode speed on the removal efficiency of chemical oxygen demand (COD), total dissolved solids (TDS), and total suspended solids (TSS) of raw landfill leachate was investigated. The influence of operating parameters like leachate pH, leachate temperature, current, and inter-distance between the cathode rings and anode impellers on the electrocoagulation performance were also investigated. The results revealed the optimum rotating speed is 150 rpm and increasing the rotating speed above this value led to reducing process performance. The leachate electrocoagulation treatment process favors the neutral medium and the treatment performance increases with increasing current intensity. Furthermore, the electrocoagulation treatment performance improves with increasing leachate temperature. However, the performance reduces with increasing inter-electrode distance.

Matched MeSH terms: Waste Disposal, Fluid/methods*

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links