MyMedR

Displaying publications 1 - 20 of 33 in total

Abstract:

Sort:

3D N-doped carbon derived from zeolitic imidazole framework as heterogeneous catalysts for decomposition of pulp and paper mill effluent: Optimization and kinetics study

Saputra E, Prawiranegara BA, Nugraha MW, Oh WD, Sugesti H, Evelyn, et al.

Environ Res, 2023 Oct 01;234:116441.
PMID: 37331558 DOI: 10.1016/j.envres.2023.116441

Three specific catalysts, namely ZIF-67 (zeolitic imidazolate framework-67), Co@NCF (Co@Nitrogen-Doped Carbon Framework), and 3D NCF (Three-Dimensional Nitrogen-Doped Carbon Framework), were prepared and studied for pulp and paper mill effluent degradation using heterogeneous activation of peroxymonosulfate (PMS). Numerous characterizations, including scanning electron microscopy (SEM), X-ray diffraction (XRD), and N2 adsorption, were used to characterize the properties of three different catalysts. 3D NCF is remarkably effective at heterogeneous activation of PMS to generate sulfate radicals to degrade pulp and paper mill effluent (PPME) compared to the other as-prepared catalysts. The catalytic activity reveals a sequence of 3D NCF > Co@NCF > ZIF-67.3D NCF could degrade organic pollutants in 30 min at an initial COD concentration of 1146 mg/L of PPME, 0.2 g/L catalysts, 2 g/L PMS, and 50 °C. Consequently, it was observed that the degradation of PPME using 3D NCF followed first-order kinetics, with an activation energy of 40.54 kJ mol-1. Overall, 3D NCF/PMS system reveals promising performance for PPME removal.
Kinetic modeling of bioregeneration of chlorophenol-loaded granular activated carbon in simultaneous adsorption and biodegradation processes

Oh WD, Lim PE, Seng CE, Sujari AN

Bioresour Technol, 2012 Jun;114:179-87.
PMID: 22503192 DOI: 10.1016/j.biortech.2012.03.065

A kinetic model incorporating adsorption, desorption and biodegradation processes was developed to describe the bioregeneration of granular activated carbon (GAC) loaded with 4-chlorophenol (4-CP) and 2,4-dichlorophenol (2,4-DCP), respectively, in simultaneous adsorption and biodegradation processes. The model was numerically solved and the results showed that the kinetic model was well-fitted (R(2)>0.83) to the experimental data at different GAC dosages and at various initial 4-CP and 2,4-DCP concentrations. The rate of bioregeneration in simultaneous adsorption and biodegradation processes was influenced by the ratio of initial chlorophenol concentration to GAC dosage. Enhancement in the rate of bioregeneration was achieved by using the lowest ratio under either one of the following experimental conditions: (1) increasing initial chlorophenol concentration at constant GAC dosage and (2) increasing GAC dosage at constant initial chlorophenol concentration. It was found that the rate enhancement was more pronounced under the second experimental condition.
Bioregeneration of granular activated carbon in simultaneous adsorption and biodegradation of chlorophenols

Oh WD, Lim PE, Seng CE, Sujari AN

Bioresour Technol, 2011 Oct;102(20):9497-502.
PMID: 21871793 DOI: 10.1016/j.biortech.2011.07.107

The objectives of this study are to obtain the time courses of the amount of chlorophenol adsorbed onto granular activated carbon (GAC) in the simultaneous adsorption and biodegradation processes involving 4-chlorophenol (4-CP) and 2,4-dichlorophenol (2,4-DCP), respectively, and to quantify the bioregeneration efficiency of GAC loaded with 4-CP and 2,4-DCP by direct measurement of the amount of chlorophenol adsorbed onto GAC. Under abiotic and biotic conditions, the time courses of the amount of chlorophenol adsorbed onto GAC at various GAC dosages for the initial 4-CP and 2,4-DCP concentrations below and above the biomass acclimated concentrations of 300 and 150 mg/L, respectively, were determined. The results show that the highest bioregeneration efficiency was achieved provided that the initial adsorbate concentration was lower than the acclimated concentration. When the initial adsorbate concentration was higher than the acclimated concentration, the highest bioregeneration efficiency was achieved if excess adsorbent was used.
Chitosan modifications for adsorption of pollutants - A review

Saheed IO, Oh WD, Suah FBM

J Hazard Mater, 2021 04 15;408:124889.
PMID: 33418525 DOI: 10.1016/j.jhazmat.2020.124889

In recent times, research interest into the development of biodegradable, cost-effective and environmental friendly adsorbents with favourable properties for adsorption of pollutants is a challenge. Modification of chitosan via different physical and chemical methods have gained attention as a promising approach for removing organic (such as dyes and pharmaceuticals) and inorganic (such as metal/metal ions) pollutants from aqueous medium. In this regard, researchers have reported grafting and cross-linking approach among others as a potentially useful method for chitosan's modification for improved adsorption efficiency with respect to pollutant uptake. This article reviews the trend in chitosan modification, with regards to the summary of some recently published works on modification of chitosan and their adsorption application in pollutants (metal ion, dyes and pharmaceuticals) removal from aqueous medium. The review uniquely highlights some common cross-linkers and grafting procedures for chitosan modification, their influence on structure and adsorption capacity of modified-chitosan with respect to pollutants removal. Findings revealed that the performance of modified chitosan for adsorption of pollutants depends largely on the modification method adopted, materials used for the modification and adsorption experimental conditions. Cross-linking is commonly utilized for improving the chemical and mechanical stabilities of chitosan but usually decreases adsorption capacity of chitosan/modified-chitosan for adsorption of pollutants. However, literature survey revealed that adsorption capacity of cross-linked chitosan based materials have been enhanced in recently published works either by grafting, incorporation of solid adsorbents (e.g metals, clays and activated carbon) or combination of both prior to cross-linking.
Enhanced adsorption of acid Blue-25 dye onto chitosan/porous carbon composite modified in 1-allyl-3-methyl imidazolium bromide ionic liquid

Saheed IO, Oh WD, Suah FBM

Int J Biol Macromol, 2021 Jul 31;183:1026-1033.
PMID: 33971228 DOI: 10.1016/j.ijbiomac.2021.05.042

In this study, chitosan/porous carbon composite (C-PC) modified in 1-Allyl-3-methyl imidazolium bromide [AMIM][Br] under airtight condition was prepared for the removal of Acid Blue-25 dye (AB-25) from aqueous medium. For comparison of adsorption efficiency of C-PC, chitosan-activated carbon composite (C-AC) was also prepared in 1% acetic acid. The adsorbents were characterised using SEM, EDX, XRD, BET, TGA and FTIR. The micrograph of C-PC revealed cavities and slightly rough surfaces dominated with similar sized and irregular shaped stone-like materials which differ from the precursors' micrograph. BET analysis revealed the domination of mesopores on the C-PC and C-AC surfaces, as the hydroxyl and amino group on C-PC are the main active sites for AB-25 dye uptake. The dye was better adsorbed onto C-PC at pH 2 and C-AC at pH 4. The adsorption capacity obtained for C-PC, C-AC, activated carbon (AC) and chitosan (CH) using Langmuir isotherm model are 3333.33 mg/g, 909.90 mg/g, 909.09 mg/g and 833.33 mg/g, respectively. The experimental data are well described by Langmuir and Fruendlich isotherms for adsorption of the dye onto C-PC, AC and CH. C-AC fitted into Langmuir isotherm only. The kinetics of the adsorption fitted into pseudo-second order indicating the possibility of chemical interactions in the adsorption process.
Fabrication of chitosan@activated carbon composites in EmimAc for Cd(II) adsorption from aqueous solution: Experimental, optimization and DFT study

Saheed IO, Yusof ENM, Oh WD, Hanafiah MAKM, Suah FBM

Int J Biol Macromol, 2023 Jul 01;242(Pt 2):124798.
PMID: 37178882 DOI: 10.1016/j.ijbiomac.2023.124798

Adsorption efficiency of a duo-material blend featuring the fabrication of modified chitosan adsorbents (powder (C-emimAc), bead (CB-emimAc) and sponge (CS-emimAc)) for the removal of Cd(II) from aqueous solution was investigated. The chitosan@activated carbon (Ch/AC) blend was developed in a green ionic solvent, 1-ethyl-3-methyl imidazolium acetate (EmimAc) and its characteristics was examined using FTIR, SEM, EDX, BET and TGA. The possible mechanism of interaction between the composites and Cd(II) was also predicted using the density functional theory (DFT) analysis. The interactions of various blend forms (C-emimAc, CB-emimAc and CS-emimAc) with Cd(II) gave better adsorption at pH 6. The composites also present excellent chemical stability in both acidic and basic conditions. The monolayer adsorption capacities obtained (under the condition 20 mg/L [Cd], adsorbent dosage 5 mg, contact time 1 h) for the CB-emimAc (84.75 mg/g) > C-emimAc (72.99 mg/g) > CS-emimAc (55.25 mg/g), as this was supported by their order of increasing BET surface area (CB-emimAc (120.1 m2/g) > C-emimAc (67.4 m2/g) > CS-emimAc (35.3 m2/g)). The feasible adsorption interactions between Cd(II) and Ch/AC occurs through the O-H and N-H groups of the composites, as supported by DFT analysis in which an electrostatic interactions was predicted as the dominant force. The interaction energy (-1309.35 eV) calculated via DFT shows that the Ch/AC with amino (-NH) and hydroxyl (-OH) groups are more effective with four significant electrostatic interactions with the Cd(II) ion. The various form of Ch/AC composites developed in EmimAc possess good adsorption capacity and stability for the adsorption Cd(II).
Fulltext Analysis of chemical compositions and larvicidal activity of nut extracts from Areca catechu Linn against Aedes (Diptera: Culicidae)

Bharathithasan M, Ravindran DR, Rajendran D, Chun SK, Abbas SA, Sugathan S, et al.

PLoS One, 2021;16(11):e0260281.
PMID: 34843539 DOI: 10.1371/journal.pone.0260281

BACKGROUND: There is a growing need to use green alternative larvicidal control for Aedes larvae compared to chemical insecticides. Substantial reliance on chemical insecticides caused insecticide resistance in mosquito populations. Thus, research for alternate chemical compounds from natural products is necessary to control Aedes larvae. This study explores the analysis of chemical compositions from Areca catechu nut as a potential larvicide for Aedes (Diptera: Culicidae).
METHODS: The Areca catechu nut collected from Ipoh, Perak, Malaysia was grounded into powder and used for Soxhlet extraction. The chemical analysis of the extracts and their structures were identified using the GCMS-QP2010 Ultra (Shimadzu) system. National Institute of Standards and Technology (NIST) Chemistry WebBook, Standard Reference Database 69 (https://webbook.nist.gov/chemistry/) and PubChem (https://pubchem.ncbi.nlm.nih.gov/), the two databases used to retrieve the synonyms, molecular formula, molecular weight, and 2-dimensional (2D) structure of chemical compounds. Next, following WHO procedures for larval bioassays, the extracts were used to asses larvicidal activity against early 4th instar larvae of Aedes aegypti and Aedes albopictus.
RESULTS: The larvicidal activities were observed against early 4th stage larvae with different concentrations in the range from 200 mg/L to 1600 mg/L. The LC50 and LC95 of Aedes aegypti were 621 mg/L and 2264 mg/L respectively; whereas the LC50 and LC95 of Aedes albopictus were 636 mg/L and 2268 mg/L respectively. Mortality was not observed in the non-target organism test. The analysis using gas chromatography and mass spectrometer recovered several chemical compounds such as Arecaidine, Dodecanoic acid, Methyl tetradecanoate, Tetradecanoic acid , and n-Hexadecanoic acid bioactive components. These chemical constituents were used as additive formulations in pesticides, pest control, insect repellent, and insecticidal agents.
CONCLUSIONS: Our study showed significant outcomes from the extract of Areca catechu nut and it deserves further investigation in relation to chemical components and larvicidal actions between different species of Aedes mosquitoes. Even though all these findings are fundamental, it may have some interesting potentials to be developed as natural bio-larvicidal products.
H3PO4 activation mediated the iron phase transformation and enhanced the removal of bisphenol A on iron carbide-loaded activated biochar

Zhao N, Liu K, He C, Zhao D, Zhu L, Zhao C, et al.

Environ Pollut, 2022 Feb 05;300:118965.
PMID: 35134429 DOI: 10.1016/j.envpol.2022.118965

Zero valent iron-loaded biochar (Fe0-BC) has shown promise for the removal of various organic pollutants, but is restricted by reduced specific surface area, low utilization efficiency and limited production of reactive oxygen species (ROS). In this study, iron carbide-loaded activated biochar (Fe3C-AB) with a high surface area was synthesized through the pyrolysis of H3PO4 activated biochar with Fe(NO3)3, tested for removing bisphenol A (BPA) and elucidated the adsorption and degradation mechanisms. As a result, H3PO4 activated biochar was beneficial for the transformation of Fe0 to Fe3C. Fe3C-AB exhibited a significantly higher removal rate and removal capacity for BPA than that of Fe0-BC within a wide pH range of 5.0-11.0, and its performance was maintained even under extremely high salinity and different water sources. Moreover, X-ray photoelectron spectra and density functional theory calculations confirmed that hydrogen bonds were formed between the COOH groups and BPA. 1O2 was the major reactive species, constituting 37.0% of the removal efficiency in the degradation of BPA by Fe3C-AB. Density functional reactivity theory showed that degradation pathway 2 of BPA was preferentially attacked by ROS. Thus, Fe3C-AB with low cost and excellent recycling performance could be an alternative candidate for the efficient removal of contaminants.
Can biochar and hydrochar be used as sustainable catalyst for persulfate activation?

Gasim MF, Lim JW, Low SC, Lin KA, Oh WD

Chemosphere, 2022 Jan;287(Pt 4):132458.
PMID: 34610377 DOI: 10.1016/j.chemosphere.2021.132458

Over the past decade, there has been a surge of interest in using char (hydrochar or biochar) derived from biomass as persulfate (PS, either peroxymonosulfate or peroxydisulfate) activator for anthropogenic pollutants removal. While extensive investigation showed that char could be used as a PS activator, its sustainability over prolonged application is equivocal. This review provides an assessment of the knowledge gap related to the sustainability of char as a PS activator. The desirable char properties for PS activation are identified, include the high specific surface area and favorable surface chemistry. Various synthesis strategies to obtain the desirable properties during biomass pre-treatment, hydrochar and biochar synthesis, and char post-treatment are discussed. Thereafter, factors related to the sustainability of employing char as a PS activator for anthropogenic pollutants removal are critically evaluated. Among the critical factors include performance uncertainty, competing adsorption process, char stability during PS activation, biomass precursor variation, scalability, and toxic components in char. Finally, some potential research directions are provided. Fulfilling the sustainability factors will provide opportunity to employ char as an economical and efficient catalyst for sustainable environmental remediation.
Multi-heteroatom-doped carbocatalyst as peroxymonosulfate and peroxydisulfate activator for water purification: A critical review

Choong ZY, Lin KA, Lisak G, Lim TT, Oh WD

J Hazard Mater, 2022 03 15;426:128077.
PMID: 34953256 DOI: 10.1016/j.jhazmat.2021.128077

Catalytic activation of peroxymonosulfate (PMS) and peroxydisulfate (PDS) (or collectively known as persulfate, PS) using carbocatalyst is increasingly gaining attention as a promising technology for sustainable recalcitrant pollutant removal in water. Single heteroatom doping using either N, S, B or P is widely used to enhance the performance of the carbocatalyst for PS activation. However, the performance enhancement from single heteroatom doping is limited by the type of heteroatom used. To further enhance the performance of the carbocatalyst beyond the limit of single heteroatom doping, multi-heteroatom doping can be conducted. This review aims to provide a state-of-the-art overview on the development of multi-heteroatom-doped carbocatalyst for PS activation. The potential synergistic and antagonistic interactions of various heteroatoms including N and B, N and S, N and P, and N and halogen for PS activation are evaluated. Thereafter, the preparation strategies to develop multi-heteroatom-doped carbocatalyst including one-step and multi-step preparation approaches along with the characterization techniques are discussed. Evidence and summary of the performance of multi-heteroatom-doped carbocatalyst for various recalcitrant pollutants removal via PS activation are also provided. Finally, the prospects of employing multi-heteroatom-doped carbocatalyst including the need to study the correlation between different heteroatom combination, surface moiety type, and amount of dopant with the PS activation mechanism, identifying the best heteroatom combination, improving the durability of the carbocatalyst, evaluating the feasibility for full-scale application, developing low-cost multi-heteroatom-doped carbocatalyst, and assessing the environmental impact are also briefly discussed.
Importance of carbon structure for nitrogen and sulfur co-doping to promote superior ciprofloxacin removal via peroxymonosulfate activation

Gasim MF, Veksha A, Lisak G, Low SC, Hamidon TS, Hussin MH, et al.

J Colloid Interface Sci, 2023 Mar 15;634:586-600.
PMID: 36549207 DOI: 10.1016/j.jcis.2022.12.072

Herein, five N, S-co-doped carbocatalysts were prepared from different carbonaceous precursors, namely sawdust (SD), biochar (BC), carbon-nanotubes (CNTs), graphite (GP), and graphene oxide (GO) and compared. Generally, as the graphitization degree increased, the extent of N and S doping decreased, graphitic N configuration is preferred, and S configuration is unaltered. As peroxymonosulfate (PMS) activator for ciprofloxacin (CIP) removal, the catalytic performance was in order: NS-CNTs (0.037 min-1) > NS-BC (0.032 min-1) > NS-rGO (0.024 min-1) > NS-SD (0.010 min-1) > NS-GP (0.006 min-1), with the carbonaceous properties, rather than the heteroatoms content and textural properties, being the major factor affecting the catalytic performance. NS-CNTs was found to have the supreme catalytic activity due to its remarkable conductivity (3.38 S m-1) and defective sites (ID/IG = 1.28) with high anti-interference effect against organic and inorganic matter and varying water matrixes. The PMS activation pathway was dominated by singlet oxygen (1O2) generation and electron transfer regime between CIP and PMS activated complexes. The CIP degradation intermediates were identified, and a degradation pathway is proposed. Overall, this study provides a better understanding of the importance of selecting a suitable carbonaceous platform for heteroatoms doping to produce superior PMS activator for antibiotics decontamination.
Effect of metal doping (Me = Zn, Cu, Co, Mn) on the performance of bismuth ferrite as peroxymonosulfate activator for ciprofloxacin removal

Koo PL, Choong ZY, He C, Bao Y, Jaafar NF, Oh WD

Chemosphere, 2023 Mar;318:137915.
PMID: 36702411 DOI: 10.1016/j.chemosphere.2023.137915

In this study, a facile hydrothermal method was employed to prepare Me-doped Bi2Fe4O9 (Me = Zn, Cu, Co, and Mn) as peroxymonosulfate (PMS) activator for ciprofloxacin (CIP) degradation. The characteristics of the Me-doped bismuth ferrites were investigated using various characterization instruments including SEM, TEM, FTIR and porosimeter indicating that the Me-doped Bi2Fe4O9 with nanosheet-like square orthorhombic structure was successfully obtained. The catalytic activity of various Me-doped Bi2Fe4O9 was compared and the results indicated that the Cu-doped Bi2Fe4O9 at 0.08 wt.% (denoted as BFCuO-0.08) possessed the greatest catalytic activity (kapp = 0.085 min-1) over other Me-doped Bi2Fe4O9 under the same condition. The synergistic interaction between Cu, Fe and oxygen vacancies are the key factors which enhanced the performance of Me-doped Bi2Fe4O9. The effects of catalyst loading, PMS dosage, and pH on CIP degradation were also investigated indicating that the performance increased with increasing catalyst loading, PMS dosage, and pH. Meanwhile, the dominant reactive oxygen species was identified using the chemical scavengers with SO4•-, •OH, and 1O2 playing a major role in CIP degradation. The performance of BFCuO-0.08 deteriorated in real water matrix (tap water, river water and secondary effluent) due to the presence of various water matrix species. Nevertheless, the BFCuO-0.08 catalyst possessed remarkable stability and can be reused for at least four successive cycles with >70% of CIP degradation efficiency indicating that it is a promising catalyst for antibiotics removal.
Recent advances in catalyst design, performance, and challenges of metal-heteroatom-co-doped biochar as peroxymonosulfate activator for environmental remediation

Manickavasagam G, He C, Lin KA, Saaid M, Oh WD

Environ Res, 2024 Apr 16;252(Pt 2):118919.
PMID: 38631468 DOI: 10.1016/j.envres.2024.118919

The escalation of global water pollution due to emerging pollutants has gained significant attention. To address this issue, catalytic peroxymonosulfate (PMS) activation technology has emerged as a promising treatment approach for effectively decontaminating a wide range of pollutants. Recently, modified biochar has become an increasingly attractive as PMS activator. Metal-heteroatom-co-doped biochar (MH-BC) has emerged as a promising catalyst that can provide enhanced performance over heteroatom-doped and metal-doped biochar due to the synergism between metal and heteroatom in promoting PMS activation. Therefore, this review aims to discuss the fabrication pathways (i.e., internal vs external doping and pre-vs post-modification) and key parameters (i.e., source of precursors, synthesis methods, and synthesis conditions) affecting the performance of MH-BC as PMS activator. Subsequently, an overview of all the possible PMS activation pathways by MH-BC is provided. Subsequently, Also, the detection, identification, and quantification of several reactive species (such as, •OH, SO4•-, O2•-, 1O2, and high valent oxo species) generated in the catalytic PMS system by MH-BC are also evaluated. Lastly, the underlying challenges associated with poor stability, the lack of understanding regarding the interaction between metal and heteroatom during PMS activation and quantification of radicals in multi-ROS system are also deliberated.
Fulltext The potential use of Azolla pinnata as an alternative bio-insecticide

Ravi R, Rajendran D, Oh WD, Mat Rasat MS, Hamzah Z, Ishak IH, et al.

Sci Rep, 2020 11 06;10(1):19245.
PMID: 33159109 DOI: 10.1038/s41598-020-75054-0

Four different tests showed the effectiveness of Azolla pinnata plant extracts against Aedes aegypti and Aedes albopictus mosquitoes. In the adulticidal test, there was a significant increase in mortality as test concentration increases and A. pinnata extracts showed LC50 and LC95 values of 2572.45 and 6100.74 ppm, respectively, against Ae. aegypti and LC50 and LC95 values of 2329.34 and 5315.86 ppm, respectively, against Ae. albopictus. The ovicidal test showed 100% eggs mortality for both species tested for all the concentrations tested at 1500 ppm, 1000 ppm, 500 ppm, 250 ppm and 125 ppm. Both tested samples of Ae. aegypti and Ae. albopictus did not lay any eggs in the plastic cups filled with the A. pinnata extract but instead opted to lay eggs in the plastic cups filled with water during the oviposition deterrence test. Similarly, the non-choice test of Ae. aegypti mosquitoes laid eggs on the sucrose solution meant for the nutrient source of the mosquitoes instead of in the plastic cup that was designed to facilitate oviposition filled with the extract. This clearly indicates the presence of bioactive compounds which are responsible in adulticidal and ovicidal activity in Aedes mosquitoes and at the same time inducing repellence towards the mosquitoes. The LC-MS results showed mainly three important chemical compounds from A. pinnata extracts such as 1-(O-alpha-D-glucopyranosyl)-(1,3R,25R)-hexacosanetriol, Pyridate and Nicotinamide N-oxide. All these chemicals have been used for various applications such as both emulsion and non-emulsion type of cosmetics, against mosquito vector such as Culex pipens and Anopheles spp. Finally, the overall view of these chemical components from A. pinnata extracts has shown the potential for developing natural product against dengue vectors.
High-sulfur capacity and regenerable Zn-based sorbents derived from layered double hydroxide for hot coal gas desulfurization

Wu M, Chang B, Lim TT, Oh WD, Lei J, Mi J

J Hazard Mater, 2018 Oct 15;360:391-401.
PMID: 30130697 DOI: 10.1016/j.jhazmat.2018.08.015

The Zn-Al mixed metal oxide (ZnAl-MMO) with a plate-like structure was derived from Zn-Al layered double hydroxide. The ZnAl-MMO with a Zn/Al molar ratio of 3:1 exhibits superior absorption ability for H2S in a simulated coal gas at 600 ℃ due to the special structure of the ZnAl-MMO. Besides ZnS, elemental sulfur is also produced during the desulfurization process. The deactivation model could well simulate the absorption behavior of H2S. The sulfidation reaction over the sorbent shows large initial reaction rate constants (1110-5390 m3 min-1 kg-1) and low activation energy (29.5 kJ mol-1). The regeneration rate of the used sorbent can reach 99.8% under the optimum conditions. The regenerated sorbents still show high sulfur capacity (ca. 30%), implying its great application potential for industrial-scale desulfurization of the hot coal gas.
Metal-organic frameworks for pesticidal persistent organic pollutants detection and adsorption - A mini review

Wagner M, Andrew Lin KY, Oh WD, Lisak G

J Hazard Mater, 2021 07 05;413:125325.
PMID: 33601143 DOI: 10.1016/j.jhazmat.2021.125325

The global population growth demands intensification of anthropogenic processes, thus leading to inter alia pollution of both land and aquatic environments with toxic organic compounds. Particularly harmful synthetic compounds are classified as persistent organic pollutants (POPs). Their relatively high chemical resistance resulted in a worldwide ban or strict control on the use of POPs. The majority of POPs were commonly used as pesticides, and unfortunately, some of them are still utilized as an aid in agricultural practices. Therefore, environmental monitoring in terms of reliable detection and quantification of pesticidal POPs is an ever-increasing need. Chemical sensors and adsorption materials crafted for specific pesticide operate on host-guest interactions should provide selectivity and sensitivity, thus leading to the detection of target molecule down to the nanomolar range. This could be achieved with materials exhibiting a very large active surface area, well-defined structure, and high stability. The novel materials studied in that context are metal-organic frameworks (MOFs). The structure of various MOFs can be functionalized to provide desired host-guest interactions. In this mini-review, we critically discuss the application of MOFs for the detection and adsorption of selected pesticides that are classified as POPs according to the Stockholm Convention.
Processing of flexible plastic packaging waste into pyrolysis oil and multi-walled carbon nanotubes for electrocatalytic oxygen reduction

Veksha A, Yin K, Moo JGS, Oh WD, Ahamed A, Chen WQ, et al.

J Hazard Mater, 2020 04 05;387:121256.
PMID: 31951979 DOI: 10.1016/j.jhazmat.2019.121256

Flexible plastic packaging waste causes serious environmental issues due to challenges in recycling. This study investigated the conversion of flexible plastic packaging waste with 11.8 and 27.5 wt.% polyethylene terephthalate (PET) (denoted as PET-12 and PET-28, respectively) into oil and multi-walled carbon nanotubes (MWCNTs). The mixtures were initially pyrolyzed and the produced volatiles were processed over 9.0 wt.% Fe2O3 supported on ZSM-5 (400 °C) to remove oxygenated hydrocarbons (catalytic cracking of terephthalic and benzoic acids) that deteriorate oil quality. The contents of oxygenated hydrocarbons were decreased in oil from 4.6 and 9.4 wt.% per mass of PET-12 and PET-28, respectively, to undetectable levels. After catalytic cracking, the oil samples had similar contents of gasoline, diesel and heavy oil/wax fractions. The non-condensable gas was converted into MWCNTs over 0.9 wt.% Ni supported on CaCO3 (700 °C). The type of plastic packaging influenced the yields (2.4 and 1.5 wt.% per mass of PET-12 and PET-28, respectively) and the properties of MWCNTs due to the differences in gas composition. Regarding the electrocatalytic application, both MWCNTs from PET-12 and PET-28 outperformed commercial MWCNTs and Pt-based electrodes during oxygen evolution reaction, suggesting that MWCNTs from flexible plastic packaging can potentially replace conventional electrode materials.
Co3O4 nanocube-decorated nitrogen-doped carbon foam as an enhanced 3-dimensional hierarchical catalyst for activating Oxone to degrade sulfosalicylic acid

Lin XR, Kwon E, Hung C, Huang CW, Oh WD, Lin KA

J Colloid Interface Sci, 2021 Feb 15;584:749-759.
PMID: 33176929 DOI: 10.1016/j.jcis.2020.09.104

As sulfosalicylic acid (SUA) is extensively used as a pharmaceutical product, discharge of SUA into the environment becomes an emerging environmental issue because of its low bio-degradability. Thus, SO4--based advanced oxidation processes have been proposed for degrading SUA because of many advantages of SO4-. As Oxone represents a dominant reagent for producing SO4-, and Co is the most capable metal for activating Oxone to generate SO4-, it is critical to develop an effective but easy-to-use Co-based catalysts for Oxone activation to degrade SUA. Herein, a 3D hierarchical catalyst is specially created by decorating Co3O4 nanocubes (NCs) on macroscale nitrogen-doped carbon form (NCF). This Co3O4-decorated NCF (CONCF) is free-standing, macroscale and even squeezable to exhibit interesting and versatile features. More importantly, CONCF consists of Co3O4 NCs evenly distributed on NCF without aggregation. The NCF not only serves as a support for Co3O4 NCs but also offers additional active sites to synergistically enhance catalytic activities towards Oxone activation. Therefore, CONCF exhibits a higher catalytic activity than the conventional Co3O4 nanoparticles for activating Oxone to fully eliminate SUA in 30 min with a rate constant of 0.142 min-1. CONCF exhibits a much lower Ea value of SUA degradation (35.2 kJ/mol) than reported values, and stable catalytic activities over multi-cyclic degradation of SUA. The mechanism of SUA degradation is also explored, and degradation intermediates of SUA degradation are identified to provide a possible pathway of SUA degradation. These features validate that CONCF is certainly a promising 3D hierarchical catalyst for enhanced Oxone activation to degrade SUA. The findings obtained here are also insightful to develop efficient heterogeneous Oxone-activating catalysts for eliminating emerging contaminants.
Metal-complexed covalent organic frameworks derived N-doped carbon nanobubble-embedded cobalt nanoparticle as a magnetic and efficient catalyst for oxone activation

Nguyen HT, Lee J, Kwon E, Lisak G, Thanh BX, Oh WD, et al.

J Colloid Interface Sci, 2021 Jun;591:161-172.
PMID: 33601102 DOI: 10.1016/j.jcis.2021.01.108

While Cobalt nanoparticles (Co NPs) are useful for catalytic Oxone activation, it is more advantageous to embed/immobilize Co NPs on nitrogen-doped carbon substrates to provide synergy for enhancing catalytic performance. Herein, this study proposes to fabricate such a composite by utilizing covalent organic frameworks (COF) as a precursor. Through complexation of COF with Co, a stable product of Co-complexed COF (Co-COF) can be synthesized. This Co-COF is further converted through pyrolysis to N-doped carbon in which cobaltic NPs are embedded. Owing to its well-defined structures of Co-COF, the pyrolysis process transforms COF into N-doped carbon with a bubble-like morphology. Such Co NP-embedded N-doped carbon nanobubbles (CoCNB) with pores, magnetism and Co, shall be a promising catalyst. Thus, CoCNB shows a much stronger catalytic activity than commercial Co3O4 NPs to activate Oxone to degrade toxic Amaranth dye (AMD). CoCNB-activated Oxone also achieves a significantly lower Ea value of AMD degradation (i.e., 27.9 kJ/mol) than reported Ea values in previous literatures. Besides, CoCNB is still effective for complete elimination of AMD in the presence of high-concentration NaCl and surfactants, and CoCNB is also reusable over five consecutive cycles.
Hierarchical ZIF-decorated nanoflower-covered 3-dimensional foam for enhanced catalytic reduction of nitrogen-containing contaminants

Lin JY, Lee J, Oh WD, Kwon E, Tsai YC, Lisak G, et al.

J Colloid Interface Sci, 2021 Nov 15;602:95-104.
PMID: 34118608 DOI: 10.1016/j.jcis.2021.05.098

Metal Organic Frameworks (MOFs) represent a promising class of metallic catalysts for reduction of nitrogen-containing contaminants (NCCs), such as 4-nitrophenol (4-NP). Nevertheless, most researches involving MOFs for 4-NP reduction employ noble metals in the form of fine powders, making these powdered noble metal-based MOFs impractical and inconvenient for realistic applications. Thus, it would be critical to develop non-noble-metal MOFs which can be incorporated into macroscale and porous supports for convenient applications. Herein, the present study proposes to develop a composite material which combines advantageous features of macroscale/porous supports, and nanoscale functionality of MOFs. In particular, copper foam (CF) is selected as a macroscale porous medium, which is covered by nanoflower-structured CoO to increase surfaces for growing a cobaltic MOF, ZIF-67. The resultant composite comprises of CF covered by CoO nanoflowers decorated with ZIF-67 to form a hierarchical 3D-structured catalyst, enabling this ZIF-67@Cu foam (ZIF@CF) a promising catalyst for reducing 4-NP, and other NCCs. Thus, ZIF@CF can readily reduce 4-NP to 4-AP with a significantly lower Ea of 20 kJ/mol than reported values. ZIF@CF could be reused over 10 cycles and remain highly effective for 4-NP reduction. ZIF@CF also efficiently reduces other NCCs, such as 2-nitrophenol, 3-nitrophenol, methylene blue, and methyl orange. ZIF@CF can be adopted as catalytic filters to enable filtration-type reduction of NCCs by passing NCC solutions through ZIF@CF to promptly and conveniently reduce NCCs. The versatile and advantageous catalytic activity of ZIF@CF validates that ZIF@CF is a promising and practical heterogeneous catalyst for reductive treatments of NCCs.

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links