Displaying publications 1 - 20 of 39 in total

Abstract:
Sort:
  1. Formation of wave packets in the Ostrovsky equation for both normal and anomalous dispersion
    Grimshaw R, Stepanyants Y, Alias A
    Proc Math Phys Eng Sci, 2016 Jan;472(2185):20150416.
    PMID: 26997887
    It is well known that the Ostrovsky equation with normal dispersion does not support steady solitary waves. An initial Korteweg-de Vries solitary wave decays adiabatically through the radiation of long waves and is eventually replaced by an envelope solitary wave whose carrier wave and envelope move with different velocities (phase and group velocities correspondingly). Here, we examine the same initial condition for the Ostrovsky equation with anomalous dispersion, when the wave frequency increases with wavenumber in the limit of very short waves. The essential difference is that now there exists a steady solitary wave solution (Ostrovsky soliton), which in the small-amplitude limit can be described asymptotically through the solitary wave solution of a nonlinear Schrödinger equation, based at that wavenumber where the phase and group velocities coincide. Long-time numerical simulations show that the emergence of this steady envelope solitary wave is a very robust feature. The initial Korteweg-de Vries solitary wave transforms rapidly to this envelope solitary wave in a seemingly non-adiabatic manner. The amplitude of the Ostrovsky soliton strongly correlates with the initial Korteweg-de Vries solitary wave.
    Matched MeSH terms: Radio Waves
  2. Fulltext Review on Medical Implantable Antenna Technology and Imminent Research Challenges
    Soliman MM, Chowdhury MEH, Khandakar A, Islam MT, Qiblawey Y, Musharavati F, et al.
    Sensors (Basel), 2021 May 02;21(9).
    PMID: 34063296 DOI: 10.3390/s21093163
    Implantable antennas are mandatory to transfer data from implants to the external world wirelessly. Smart implants can be used to monitor and diagnose the medical conditions of the patient. The dispersion of the dielectric constant of the tissues and variability of organ structures of the human body absorb most of the antenna radiation. Consequently, implanting an antenna inside the human body is a very challenging task. The design of the antenna is required to fulfill several conditions, such as miniaturization of the antenna dimension, biocompatibility, the satisfaction of the Specific Absorption Rate (SAR), and efficient radiation characteristics. The asymmetric hostile human body environment makes implant antenna technology even more challenging. This paper aims to summarize the recent implantable antenna technologies for medical applications and highlight the major research challenges. Also, it highlights the required technology and the frequency band, and the factors that can affect the radio frequency propagation through human body tissue. It includes a demonstration of a parametric literature investigation of the implantable antennas developed. Furthermore, fabrication and implantation methods of the antenna inside the human body are summarized elaborately. This extensive summary of the medical implantable antenna technology will help in understanding the prospects and challenges of this technology.
    Matched MeSH terms: Radio Waves*
  3. Fulltext The impact of radiofrequency exposure on Aedes aegypti (Diptera: Culicidae) development
    Nik Abdull Halim NMH, Mohd Jamili AF, Che Dom N, Abd Rahman NH, Jamal Kareem Z, Dapari R
    PLoS One, 2024;19(2):e0298738.
    PMID: 38412167 DOI: 10.1371/journal.pone.0298738
    INTRODUCTION: Wireless communication connects billions of people worldwide, relying on radiofrequency electromagnetic fields (RF-EMF). Generally, fifth-generation (5G) networks shift RF carriers to higher frequencies. Although radio, cell phones, and television have benefitted humans for decades, higher carrier frequencies can present potential health risks. Insects closely associated with humans (such as mosquitoes) can undergo increased RF absorption and dielectric heating. This process inadvertently impacts the insects' behaviour, morphology, and physiology, which can influence their spread. Therefore, this study examined the impact of RF exposure on Ae. aegypti mosquitoes, which are prevalent in indoor environments with higher RF exposure risk. The morphologies of Ae. aegypti eggs and their developments into Ae. aegypti mosquitoes were investigated.

    METHODS: A total of 30 eggs were exposed to RF radiation at three frequencies: baseline, 900 MHz, and 18 GHz. Each frequency was tested in triplicate. Several parameters were assessed through daily observations in an insectarium, including hatching responses, development times, larval numbers, and pupation periods until the emergence of adult insects.

    RESULTS: This study revealed that the hatching rate for the 900 MHz group was the highest (79 ± 10.54%) compared to other exposures (p = 0.87). The adult emergence rate for the 900 MHz group was also the lowest at 33 ± 2.77%. A significant difference between the groups was demonstrated in the statistical analysis (p = 0.03).

    CONCLUSION: This work highlighted the morphology sensitivity of Ae. aegypti eggs and their developments in the aquatic phase to RF radiation, potentially altering their life cycle.

    Matched MeSH terms: Radio Waves/adverse effects
  4. Fulltext A novel single-feed hybrid reconfigurable microstrip patch antenna for 5G mobile communication and radio frequency energy harvesting applications at 28/38GHz
    Shereen MK, Khattak MI, Zubir F, Basit A
    PLoS One, 2022;17(1):e0260407.
    PMID: 35041686 DOI: 10.1371/journal.pone.0260407
    Reconfigurable antennas have received much attention in RF energy harvesting models owing to their selectivity for operating frequency and polarization. The characteristic of having frequency selectivity and polarization selectivity can be termed as frequency diversity and polarization diversity, respectively. This paper investigates a rectenna device with a new proposed topology in order to eliminate coupling between input and output lines and increase the rectification efficiency with the use of single feed hybrid reconfigurable antenna, switch between 28GHz and 38GHz frequency. Moreover, it is designed to charge a rechargeable battery of 1watt(W). The Reconfiguration mechanism is realized by electronically controlling different states of Switches. PIN Diode (as RLC Equivalent circuit) is used as a switch for ON/OFF states. This antenna mainly comprises rectangular shaped patches (28GHz and 38GHz) with Triango-Truncated edge at the corners. Eighteen PIN Diodes are placed symmetrically throughout the antenna presenting as, S1 & S2 for frequency reconfiguration, S3 to S6 & S7 to S10 connects Triango Truncated edge at the corners for polarization reconfiguration, and for radiation pattern reconfiguration at S11 to S14 & S15 to S18 has been used. The proposed antenna model is capable of simultaneously changing, the radiation patterns as clock and anti-clockwise directions at ±90-degree shift in E and H planes, circularly polarized (CP) states among, Linear Polarization (LP), Right Hand Circularly Polarization (RHCP), and Left Hand Circularly Polarization (LHCP). The current design describes using single antenna for energy harvesting and 5G mobile communication application. This would lead to higher output currents, leading to the ability to efficiently charge a wide variety of batteries. A fully functional prototype has been designed, fabricated and its compound reconfiguration characteristics have been validated for simulated and measured results. For validation of results, the experimental results and the simulation results from the proposed mathematical model were made into comparison, and excellent correlation between the measured and simulated results was obtained.
    Matched MeSH terms: Radio Waves*
  5. Fulltext A novel 3D ray launching technique for radio propagation prediction in indoor environments
    Geok TK, Hossain F, Chiat ATW
    PLoS One, 2018;13(8):e0201905.
    PMID: 30086170 DOI: 10.1371/journal.pone.0201905
    Radio propagation prediction simulation methods based on deterministic technique such as ray launching is extensively used to accomplish radio channel characterization. However, the superiority of the simulation depends on the number of rays launched and received. This paper presented the indoor three-dimensional (3D) Minimum Ray Launching Maximum Accuracy (MRLMA) technique, which is applicable for an efficient indoor radio wave propagation prediction. Utilizing the novel MRLMA technique in the simulation environment for ray lunching and tracing can drastically reduce the number of rays that need to be traced, and improve the efficiency of ray tracing. Implementation and justification of MRLMA presented in the paper. An indoor office 3D layouts are selected and simulations have been performed using the MRLMA and other reference techniques. Results showed that the indoor 3D MRLMA model is appropriate for wireless communications network systems design and optimization process with respect to efficiency, coverage, number of rays launching, number of rays received by the mobile station, and simulation time.
    Matched MeSH terms: Radio Waves*
  6. Fulltext Ultralow Profile, Low Passive Intermodulation, and Super-Wideband Ceiling Mount Antennas for Cellular and Public Safety Distributed Antenna Systems
    Ng KJ, Islam MT, Alevy AM, Mansor MF
    Sensors (Basel), 2020 Apr 26;20(9).
    PMID: 32357426 DOI: 10.3390/s20092456
    This paper presents an ultralow profile, low passive intermodulation (PIM), and super-wideband in-building ceiling mount antenna that covers both the cellular and public safety ultra high frequency (UHF) band for distributed antenna system (DAS) applications. The proposed antenna design utilizes a modified 2-D planar discone design concept that is miniaturized to fit into a small disc-shaped radome. The 2-D planar discone has an elliptical-shaped disc monopole and a bell-shaped ground plane, a stub at the shorting path, with asymmetrical structure and an additional proximity coupling patch to maximize the available electrical path to support the 350 MHz band range. The proposed design maximizes the radome area with a reduction of about 62% compared to similar concept type antennas. Besides, the proposed design exhibits an improved radiation pattern with null reduction compared to a typical dipole/monopole when lies at the horizontal plane. A prototype was manufactured to demonstrate the antenna performance. The VSWR and radiation pattern results agreed with the simulated results. The proposed antenna achieves a band ratio of 28.57:1 while covering a frequency range of 350-10,000 MHz. The measured passive intermodulation levels are better than -150 dBc (2 × 20 Watts) for 350, 700 and 1920 MHz bands.
    Matched MeSH terms: Radio Waves
  7. Kesan Medan Magnet Menegak ke atas Lengkung Sut Olakan Benard-Marangoni Mantap dalam Lapisan Mengufuk Bendalir (The Effect of a Vertical Magnetic Field on the Onset of Study Bernard-Marangoni Convection in a Horizontal Layer of Electrically Conducting Fluid)
    Ruwaidiah Idris, Ishak Hashim
    Sains Malaysiana, 2005;34.
    In this work we use an analytical technique to analyse the effect of a vertical uniform magnetic field on the onset of steady Benard-Marangoni convection in a horizontal layer of electrically conducting fluid subject to a uniform vertical temperature gradient in the asymptotic limit short waves. We found that in the limit of short waves, the leading order expression for the marginal curve is not affected by the magnetic field.
    Dalam makalah ini kesan medan magnet menegak seragam ke atas lengkung sut permulaan olakan mantap Benard-Marangoni dalam lapisan bendalir mengufuk berpengalir elektrik dikaji tertakluk kepada kecerunan suhu yang seragam dalam had asimptot gelombang pendek. Kami dapati medan magnet tidak memberi kesan kepada sebutan utama lengkung sut dalam had gelombang pendek.
    Matched MeSH terms: Radio Waves
  8. Fulltext Cylindrical Dielectric Resonator Antenna-Based Sensors for Liquid Chemical Detection
    Iqbal A, Smida A, Saraereh OA, Alsafasfeh QH, Mallat NK, Lee BM
    Sensors (Basel), 2019 Mar 08;19(5).
    PMID: 30857265 DOI: 10.3390/s19051200
    A compact, cylindrical dielectric resonator antenna (CDRA), using radio frequency signals to identify different liquids is proposed in this paper. The proposed CDRA sensor is excited by a rectangular slot through a 3-mm-wide microstrip line. The rectangular slot has been used to excite the CDRA for H E M 11 mode at 5.25 GHz. Circuit model values (capacitance, inductance, resistance and transformer ratios) of the proposed CDRA are derived to show the true behaviour of the system. The proposed CDRA acts as a sensor due to the fact that different liquids have different dielectric permittivities and, hence, will be having different resonance frequencies. Two different types of CDRA sensors are designed and experimentally validated with four different liquids (Isopropyl, ethanol, methanol and water).
    Matched MeSH terms: Radio Waves
  9. Fulltext Synthesis, Characterization and Development of Energy Harvesting Techniques Incorporated with Antennas: A Review Study
    Ibrahim HH, Singh MSJ, Al-Bawri SS, Islam MT
    Sensors (Basel), 2020 May 13;20(10).
    PMID: 32414069 DOI: 10.3390/s20102772
    The investigation into new sources of energy with the highest efficiency which are derived from existing energy sources is a significant research area and is attracting a great deal of interest. Radio frequency (RF) energy harvesting is a promising alternative for obtaining energy for wireless devices directly from RF energy sources in the environment. An overview of the energy harvesting concept will be discussed in detail in this paper. Energy harvesting is a very promising method for the development of self-powered electronics. Many applications, such as the Internet of Things (IoT), smart environments, the military or agricultural monitoring depend on the use of sensor networks which require a large variety of small and scattered devices. The low-power operation of such distributed devices requires wireless energy to be obtained from their surroundings in order to achieve safe, self-sufficient and maintenance-free systems. The energy harvesting circuit is known to be an interface between piezoelectric and electro-strictive loads. A modern view of circuitry for energy harvesting is based on power conditioning principles that also involve AC-to-DC conversion and voltage regulation. Throughout the field of energy conversion, energy harvesting circuits often impose electric boundaries for devices, which are important for maximizing the energy that is harvested. The power conversion efficiency (PCE) is described as the ratio between the rectifier's output DC power and the antenna-based RF-input power (before its passage through the corresponding network).
    Matched MeSH terms: Radio Waves
  10. Fulltext A new SIR-based sigmoid power control game in cognitive radio networks
    Al-Gumaei YA, Noordin KA, Reza AW, Dimyati K
    PLoS One, 2014;9(10):e109077.
    PMID: 25286044 DOI: 10.1371/journal.pone.0109077
    Interference resulting from Cognitive Radios (CRs) is the most important aspect of cognitive radio networks that leads to degradation in Quality of Service (QoS) in both primary and CR systems. Power control is one of the efficient techniques that can be used to reduce interference and satisfy the Signal-to-Interference Ratio (SIR) constraint among CRs. This paper proposes a new distributed power control algorithm based on game theory approach in cognitive radio networks. The proposal focuses on the channel status of cognitive radio users to improve system performance. A new cost function for SIR-based power control via a sigmoid weighting factor is introduced. The existence of Nash Equilibrium and convergence of the algorithm are also proved. The advantage of the proposed algorithm is the possibility to utilize and implement it in a distributed manner. Simulation results show considerable savings on Nash Equilibrium power compared to relevant algorithms while reduction in achieved SIR is insignificant.
    Matched MeSH terms: Radio Waves*
  11. Thermocatalytic treatment of biomass tar model compounds via radio frequency
    Anis S, Zainal ZA, Bakar MZ
    Bioresour Technol, 2013 May;136:117-25.
    PMID: 23567671 DOI: 10.1016/j.biortech.2013.02.049
    A new effective RF tar thermocatalytic treatment process with low energy intensive has been proposed to remove tar from biomass gasification. Toluene and naphthalene as biomass tar model compounds were removed via both thermal and catalytic treatment over a wide temperature range from 850 °C to 1200 °C and 450 °C to 900 °C, respectively at residence time of 0-0.7 s. Thermal characteristics of the new technique are also described in this paper. This study clearly clarified that toluene was much easier to be removed than naphthalene. Soot was found as the final product of thermal treatment of the tar model and completely removed during catalytic treatment. Radical reactions generated by RF non-thermal effect improve the tar removal. The study showed that Y-zeolite has better catalytic activity compared to dolomite on toluene and naphthalene removal due to its acidic nature and large surface area, even at lower reaction temperature of about 550 °C.
    Matched MeSH terms: Radio Waves*
  12. Fulltext Submandibular intraductal calculi removal as an office procedure with radiofrequency device
    Revadi G, Rahmat O, Shailendra S
    Med J Malaysia, 2010 Mar;65(1):80-2.
    PMID: 21265259 MyJurnal
    Salivary duct obstruction secondary to calculi is a common disorder of the submandibular gland and often manifesting as painful episodic swelling of the gland during meals. Complications may arise in unresolved obstruction leading to infections, abscess formation and a hypofunctioning gland. Treatment of this disorder has evolved from the traditional sialadenectomy to organ preserving procedures done under general or local anaesthesia. Our technique using Ellman Surgitron radiofrequency device, is another alternative technique for transoral removal of extraglandular calculi. It is a simple, quick an easy technique to learn that can be done in the office setting under local anaesthesia.
    Matched MeSH terms: Radio Waves/therapeutic use*
  13. Assessment of radiofrequency/microwave radiation emitted by the antennas of rooftop-mounted mobile phone base stations
    Keow MA, Radiman S
    Radiat Prot Dosimetry, 2006;121(2):122-7.
    PMID: 16357026
    Radiofrequency (RF) and microwave (MW) radiation exposures from the antennas of rooftop-mounted mobile telephone base stations have become a serious issue in recent years due to the rapidly evolving technologies in wireless telecommunication systems. In Malaysia, thousands of mobile telephone base stations have been erected all over the country, most of which are mounted on the rooftops. In view of public concerns, measurements of the RF/MW levels emitted by the base stations were carried out in this study. The values were compared with the exposure limits set by several organisations and countries. Measurements were performed at 200 sites around 47 mobile phone base stations. It was found that the RF/MW radiation from these base stations were well below the maximum exposure limits set by various agencies.
    Matched MeSH terms: Radio Waves/adverse effects*
  14. Occurrence of micronuclei in exfoliated buccal mucosal cells in mobile phone users: A case-control study
    Rashmi B, Chinna SK, Rodrigues C, Anjaly D, Bankur PK, Kannaiyan K
    Indian J Dent Res, 2021 1 13;31(5):734-737.
    PMID: 33433511 DOI: 10.4103/ijdr.IJDR_634_18
    Introduction: The use of mobile phones has increased enormously all over the world especially among young people. This technology is based upon electromagnetic radiation in the microwave frequency range [radiofrequency (RF) waves and microwaves]. The radiation frequency and modulation standards vary in the range of 300-2100 MHz, depending on the region in the world.

    Aim and Objectives: To detect the presence of micronuclei in exfoliated buccal mucosal cells of mobile phone users as well as to carry out a quantitative analysis of micronuclei in exfoliated buccal mucosal cells of mobile phone users.

    Material and Methods: A cross-sectional study was carried out in 100 individuals, out of which 50 were included under the test group and 50 under the control group. Buccal mucosal smears were obtained from each subject. Staining was done using papanicuolau (PAP) stain and the slides were examined for the presence of micronuclei.

    Results: The mean duration of mobile phone usage in years was 5.32 years for the exposed and 2.42 years for the control. Mean duration of mobile phone usage per day in the test group was 94.8 min and 12.4 min in the control group. The frequency of micronucleated cells (MNC) in test and control groups ranged from 0 to 16 and 0 to 2 respectively. The data obtained were statistically analyzed using Student t-test and significant results were obtained at 0.0001 level.

    Conclusion: Our study concluded that there is an increased frequency of micronuclei in mobile phone users which is related to carcinogenesis.

    Matched MeSH terms: Radio Waves/adverse effects
  15. Fulltext Green communication for cognitive radio networks based on game and utility-pricing theories
    Mukhlif F, Noordin KAB, Abdulghafoor OB, Izam TFTMN
    PLoS One, 2020;15(8):e0235953.
    PMID: 32841253 DOI: 10.1371/journal.pone.0235953
    The most crucial challenge in the functioning of the wireless networks is the efficient utilization of radio resources. A significant element of resource handling is power regulation. With increasing requirement of wireless data transmission services, it is essential to devise energy harvesting techniques for mobile devices. In this research, a new methodology has been proposed for distributed power regulation in cognitive radio, networks of CR are grounded on non-cooperation game phenomenon and pricing technique. QoS (Quality of service) of the user of CR is anticipated as a beneficial activity through pricing as well as dissemination of energy generating as an unbeneficial game wherein the consumers increase their overall efficacy. The price is defined as an actual function of transmission power to upraise the pricing of the most distant consumers. The proposed mathematical model shows that the proposed game model has a Nash equilibrium and is also unique. Furthermore, in order to make the proposed algorithm valid for green communication within the wireless network, the best response technique was proposed. Finally, simulation results showed that the proposed energy harvesting technique, grounded on a unique function of the utilization, reduces the consumption of transmission power and greatly improves the convergence speed; which are suitable for the vision of the 5G networks.
    Matched MeSH terms: Radio Waves*
  16. Fulltext Low-Slow-Small (LSS) Target Detection Based on Micro Doppler Analysis in Forward Scattering Radar Geometry
    Musa SA, Raja Abdullah RSA, Sali A, Ismail A, Rashid NEA
    Sensors (Basel), 2019 Jul 29;19(15).
    PMID: 31362452 DOI: 10.3390/s19153332
    The increase in drone misuse by civilian apart from military applications is alarming and need to be addressed. This drone is characterized as a low altitude, slow speed, and small radar cross-section (RCS) (LSS) target and is considered difficult to be detected and classified among other biological targets, such as insects and birds existing in the same surveillance volume. Although several attempts reported the successful drone detection on radio frequency-based (RF), thermal, acoustic, video imaging, and other non-technical methods, however, there are also many limitations. Thus, this paper investigated a micro-Doppler analysis from drone rotating blades for detection in a special Forward Scattering Radar (FSR) geometry. The paper leveraged the identified benefits of FSR mode over conventional radars, such as improved radar cross-section (RCS) value irrespective of radar absorbing material (RAM), direct signal perturbation, and high resolutions. To prove the concept, a received signal model for micro-Doppler analysis, a simulation work, and experimental validation are elaborated and explained in the paper. Two rotating blades aspect angle scenarios were considered, which are (i) when drone makes a turn, the blade cross-sectional area faces the receiver and (ii) when drone maneuvers normally, the cross-sectional blade faces up. The FSR system successfully detected a commercial drone and extracted the micro features of a rotating blade. It further verified the feasibility of using a parabolic dish antenna as a receiver in FSR geometry; this marked an appreciable achievement towards the FSR system performance, which in future could be implemented as either active or passive FSR system.
    Matched MeSH terms: Radio Waves
  17. Fulltext Measurement and Mapping of Wi-Fi Radiation Level at Hamdan Tahir Library, Universiti Sains Malaysia Health Campus
    Supardi, N. F., Mohd Taib, N. H., Abu Amat, N. H., Yusoff, M. N. S.
    Physics and Technology in Medicine, 2020;1(1):52-57.
    MyJurnal
    Wi-Fi is a wireless communication technology that uses specific electromagnetic frequencies. The increasing use of Wi-Fi has raised public concerns about the impact of electromagnetic radiation on the environment and human health. Since the exposure level of the electromagnetic field (EMF) radiation differs between different locations, it is important to measure the strength of the EMF at various locations under observation. This study aimed to obtain specific values related to the radiofrequency and microwave EMF which is described by four specific parameters, that are 1) the frequency of the wave, 2) the electric field strength E, 3) the magnetic field strength H, and 4) the power density S. This study was carried out at the first floor area of Hamdan Tahir Library, Universiti Sains Malaysia Health Campus. Mapping of Wi-Fi signal and measurement of Wi-Fi radiation level was performed at four specific locations, that are Laptop zone 1, Laptop zone 2, Computer lab, and Cozy corner. The average radiation level was compared with the ICNIRP standard limit for public user. It was observed that the Wi-Fi signal was highest in Laptop zone 2 followed by Laptop zone 1 which displayed a moderate signal strength. Whereas moderate but lower signal level was detected in Computer lab zone and Cozy corner. The electric and magnetic fields as well as power density were found highest in Laptop zone 1, followed by Laptop zone 2, Cozy corner, and Computer lab. Comparison with standard ICNIRP limit showed that the radiation level is still far below the ICNIRP limit, which is only 2% of exposure level. To conclude, Laptop zone 2 exhibited the strongest Wi-Fi signal whereas Laptop zone 1 displayed the highest radiation level. However, the strength of the electric and magnetic fields as well as power density is still far below the ICNIRP limit.
    Matched MeSH terms: Radio Waves
  18. Fulltext Investigation of Micromachined Antenna Substrates Operating at 5 GHz for RF Energy Harvesting Applications
    Mohd Yunus NH, Yunas J, Pawi A, Rhazali ZA, Sampe J
    Micromachines (Basel), 2019 Feb 22;10(2).
    PMID: 30813276 DOI: 10.3390/mi10020146
    This paper investigates micromachined antenna performance operating at 5 GHz for radio frequency (RF) energy harvesting applications by comparing different substrate materials and fabrication modes. The research aims to discover appropriate antenna designs that can be integrated with the rectifier circuit and fabricated in a CMOS (Complementary Metal-Oxide Semiconductor)-compatible process approach. Therefore, the investigation involves the comparison of three different micromachined antenna substrate materials, including micromachined Si surface, micromachined Si bulk with air gaps, and micromachined glass-surface antenna, as well as conventional RT/Duroid-5880 (Rogers Corp., Chandler, AZ, USA)-based antenna as the reference. The characteristics of the antennas have been analysed using CST-MWS (CST MICROWAVE STUDIO®-High Frequency EM Simulation Tool). The results show that the Si-surface micromachined antenna does not meet the parameter requirement for RF antenna specification. However, by creating an air gap on the Si substrate using a micro-electromechanical system (MEMS) process, the antenna performance could be improved. On the other hand, the glass-based antenna presents a good S11 parameter, wide bandwidth, VSWR (Voltage Standing Wave Ratio) ≤ 2, omnidirectional radiation pattern and acceptable maximum gain of >5 dB. The measurement results on the fabricated glass-based antenna show good agreement with the simulation results. The study on the alternative antenna substrates and structures is especially useful for the development of integrated patch antennas for RF energy harvesting systems.
    Matched MeSH terms: Radio Waves
  19. Fulltext Optical frequency upconversion technique for transmission of wireless MIMO-type signals over optical fiber
    Shaddad RQ, Mohammad AB, Al-Gailani SA, Al-Hetar AM
    ScientificWorldJournal, 2014;2014:170471.
    PMID: 24772009 DOI: 10.1155/2014/170471
    The optical fiber is well adapted to pass multiple wireless signals having different carrier frequencies by using radio-over-fiber (ROF) technique. However, multiple wireless signals which have the same carrier frequency cannot propagate over a single optical fiber, such as wireless multi-input multi-output (MIMO) signals feeding multiple antennas in the fiber wireless (FiWi) system. A novel optical frequency upconversion (OFU) technique is proposed to solve this problem. In this paper, the novel OFU approach is used to transmit three wireless MIMO signals over a 20 km standard single mode fiber (SMF). The OFU technique exploits one optical source to produce multiple wavelengths by delivering it to a LiNbO3 external optical modulator. The wireless MIMO signals are then modulated by LiNbO3 optical intensity modulators separately using the generated optical carriers from the OFU process. These modulators use the optical single-sideband with carrier (OSSB+C) modulation scheme to optimize the system performance against the fiber dispersion effect. Each wireless MIMO signal is with a 2.4 GHz or 5 GHz carrier frequency, 1 Gb/s data rate, and 16-quadrature amplitude modulation (QAM). The crosstalk between the wireless MIMO signals is highly suppressed, since each wireless MIMO signal is carried on a specific optical wavelength.
    Matched MeSH terms: Radio Waves
  20. Fulltext RF-Based Moisture Content Determination in Rice Using Machine Learning Techniques
    Azmi N, Kamarudin LM, Zakaria A, Ndzi DL, Rahiman MHF, Zakaria SMMS, et al.
    Sensors (Basel), 2021 Mar 08;21(5).
    PMID: 33800174 DOI: 10.3390/s21051875
    Seasonal crops require reliable storage conditions to protect the yield once harvested. For long term storage, controlling the moisture content level in grains is challenging because existing moisture measuring techniques are time-consuming and laborious as measurements are carried out manually. The measurements are carried out using a sample and moisture may be unevenly distributed inside the silo/bin. Numerous studies have been conducted to measure the moisture content in grains utilising dielectric properties. To the best of authors' knowledge, the utilisation of low-cost wireless technology operating in the 2.4 GHz and 915 MHz ISM bands such as Wireless Sensor Network (WSN) and Radio Frequency Identification (RFID) have not been widely investigated. This study focuses on the characterisation of 2.4 GHz Radio Frequency (RF) transceivers using ZigBee Standard and 868 to 915 MHz UHF RFID transceiver for moisture content classification and prediction using Artificial Neural Network (ANN) models. The Received Signal Strength Indicator (RSSI) from the wireless transceivers is used for moisture content prediction in rice. Four samples (2 kg of rice each) were conditioned to 10%, 15%, 20%, and 25% moisture contents. The RSSI from both systems were obtained and processed. The processed data is used as input to different ANNs models such as Support Vector Machine (SVM), K-Nearest Neighbour (KNN), Random Forest, and Multi-layer Perceptron (MLP). The results show that the Random Forest method with one input feature (RSSI_WSN) provides the highest accuracy of 87% compared to the other four models. All models show more than 98% accuracy when two input features (RSSI_WSN and RSSI_TAG2) are used. Hence, Random Forest is a reliable model that can be used to predict the moisture content level in rice as it gives a high accuracy even when only one input feature is used.
    Matched MeSH terms: Radio Waves
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links