Epizootic ulcerative syndrome (EUS) causes by aquatic oomycete fungus, Aphanomyces invadans is a dangerous fish disease of a wide range of fresh and brackish water, wild and farmed fish throughout the world. The objective of the present study was to determine the susceptibility of a number of tropical fish species to the EUS and compare the severity of infection between experimental groups.
Local wood charcoal was used as the main component of the electrodes of an air-cathode microbial
fuel cell (air-cathode MFC) in current study. The air cathode was build with finely milled charcoal powder and cement plaster as binder; while anode was made up of a packed bed of charcoal granules. Mangrove estuary brackish water was inoculated in the anodic chamber as the fuel and a source of exoelectrogens. The constructed fuel cell was monitored by measuring the potential over time. The MFC generated a stable power density at 33mW/m2 (0.5V) under a load of 200Ω after 72 hours of operation. An open circuit voltage (OCV) of 0.7mV was obtained after 15 hours operating under open circuit. The result of power generation by the constructed fuel cell indicating that wood charcoal could be used as electrode in an MFC and that brackish water contained potential exoelectrogens. However, further investigation and modification is required to increase the performance of the fuel cell.
The otoliths of sea bass (Lates calcarifer) were sampled from 23 locations in Peninsular Malaysia in order to analyse the Sr/Ca, Mg/Ca and Ba/Ca ratios. This study found that these elements/Ca ratios in sea bass otoliths were correlated with the salinity zone (thalassic series) compared with elements/Ca ratios in ambient water. The contradictory pattern of Sr/ Ca ratios and Ba/Ca ratios in otoliths was found according to salinity zone variations. Thus, oligohaline waters showed the highest Ba/Ca ratios while the highest Sr/Ca ratios were recorded for saline waters. The terrigenous enrichment of Ba in water also affects the Ba content in otoliths. The presence of Mg in otoliths acts as a rival to Ba, thus affecting Mg and Ba deposition. Meanwhile, Ba is the tracer for salinity fluctuations based on the partition coefficient (D) and it shows significant changes. However, the elements in otoliths were found to originate indirectly from the water column. The sequence of the elements/Ca ratios in otoliths and ambient water was Sr/Ca>Mg/Ca>Ba/Ca and Sr/Ca>Ba/Ca>Mg/ Ca, respectively.
Capacitive deionization (CDI) is a promising procedure for removing various charged ionic species from brackish water. The performance of graphene-based material in capacitive deionization is lower than the expectation of the industry, so highly-crumpled, few-layered graphene (HCG) and highly-crumpled nitrogen-doped graphene (HCNDG) with high surface area have been introduced as promising candidates for CDI electrodes. Thus, HCG and HCNDG were prepared by exfoliation of graphite in the presence of liquid-phase, microwave-assisted methods. An industrially-scalable, cost-effective, and simple approach was employed to synthesize HCG and HCNDG, resulting in few-layered graphene and nitrogen-doped graphene with large specific surface area. Then, HCG and HCNDG were utilized for manufacturing a new class of carbon nanostructure-based electrodes for use in large-scale CDI equipment. The electrosorption results indicated that both the HCG and HCNDG have fairly large specific surface areas, indicating their huge potential for capacitive deionization applications.
Increased primary plankton productivity was observed in a brackish water lagoon of Terengganu during the study period between January 1988 to December 1988. The lagoon is also the site for the fish cage culture activities of sea bass during the study period. An examination of water quality at the sampling stations during the study period indicated that both the organic and inorganic nutrients were high during the pre-monsoon period. The source of the nutrient in the lagoon was believed to be derived from the agro-based industrial effluents, fertilisers from paddy fields as well as untreated human and animal wastes. This coincided with the peak production of plankton in the surface waters of the brackish water lagoon. During this period both cultured and indigenous fish species were seen to suffer from oxygen asphyxiation (suffocation due to lack of oxygen). The primary productivity values ranged from 9 to 22 μg/L/h during the peak period while the microplankton species were composed of diatom, flagellates and dinoflagellates. Reduction in the primary productivity values were obtained with reduction in sallinity, specially during the peak monsoon months (November to March) corresponding to the Northeast monsoon period.
Directional solvent extraction is one of the promising membrane-less seawater desalination method. This technique was not extensively investigated due the poor mixing and separation performances of its bench-scale system. It is believed that, overcoming these drawbacks is possible now with the rapid development of microfluidics technology that enabled high-precession micro mixing and separation. This work presents microfluidics chip for extracting and separating salt from seawater. The chip was designed with two sections for extraction and separation. In both sections, the liquids were separated using capillary channels perpendicular to the main stream. The main channels were designed to be 400 µm in width and 100 µm in height. Two streams inlets were introduced through a Y-junction containing octanoic acid as the organic phase and saltwater as the aqueous phase. The desalination performance was investigated at four different temperatures and five different solvent flow rates. Water product salinity was recorded to be as low as 0.056% (w/w) at 60 °C and 40 mL/h. A maximum water yield of 5.2% was achieved at 65 °C and 40 mL/h with a very low solvent residual (70 ppm). The chip mass transfer efficiency was recorded to be as high as 68% under similar conditions. The fabricated microfluidic desalination system showed a significant improvement in terms of water yield and separation efficiency over the conventional macroscale. The high performance of this microsystem resulted from its ability to achieve a high mixing efficiency and separate phases selectively and that will provide a good platform in the near future to develop small desalination kits for personal use.
In this study, a novel rotating anode-based reactor (RAR) was designed to investigate its effectiveness in removing dissolved salts (i.e., Br-, Cl-, TDS, and SO42-) from saline water samples. Two configurations of an impeller's rotating anode with various operation factors, such as operating time (min), rotating speed (rpm), current density (mA/cm2), temperature (°C), pH, and inter-electrode space (cm), were used in the desalination process. The total cost consumed was calculated on the basis of the energy consumption and aluminum (Al) used in the desalination. In this respect, operating costs were calculated using optimal operating conditions. Salinity was removed electrochemically from saline water through electrocoagulation (EC). Results showed that the optimal adjustments for treating saline water were carried out at the following conditions: 150 and 75 rpm rotating speeds for the impeller's rod anode and plate anode designs, respectively; 2 mA/cm2 current density (I), 1 cm2 inter-electrode space, 25 °C temperature, 10 min operation time, and pH 8. The results indicated that EC technology with impeller plates of rotating anode can be considered a very cost-effective technique for treating saline water.
Total mercury (THg) and methylmercury (MeHg) concentrations were determined from sediment samples collected from thirty sampling stations in Port Klang, Malaysia. Three stations had THg concentrations exceeding the threshold effect level of the Florida Department of Environmental Protection and the Canadian interim sediment quality guidelines. THg and MeHg concentrations were found to be concentrated in the Lumut Strait where inputs from the two most urbanized rivers in the state converged (i.e. Klang River and Langat River). This suggests that Hg in the study area likely originated from the catchments of these rivers. MeHg made up 0.06-94.96% of the sediment's THg. There is significant positive correlation (p
Red tide of dinoflagellate was observed in brackish water fish ponds of Terengganu along the coast of the South China Sea during the study period between January 1992 to December 1992. The nearby coastal moat water facing the South China Sea is the source of water for fish pond culture activities of sea bass during the study period. An examination of water quality in fish ponds during the study period indicated that both the organic nutrients were high during the pre-wet monsoon period. The source of the nutrients in coastal water was believed to be derived from the agro-based industrial effluents, fertilizers from paddy fields and untreated animal wastes. This coincided with the peak production of dinoflagellate in the water column in October 1992. The cell count ranges from 8.3 to 60.4×10.4×10(4)/l during the bloom peak period and the bloom species were compared entirely of non-toxic dinoflagellates with Protoperidinium quinquecorne occurring >90% of the total cell count. However, both cultured and indigenous fish species were seen to suffer from oxygen asphyxiation (suffocation due to lack of oxygen). The bloom lasted for a short period (4-5 days) with a massive cell collapse from subsurface to bottom water on the sixth day. The productivity values ranged from 5-25 C g/ l / h with a subsurface maximum value in October 1992. Two species of Ciliophora, Tintinnopsis and Favella, were observed to graze on these dinoflagellates at the end of the bloom period.
Mosquito borne diseases have remained a grave threat to human health and are posing a significant burden on health authorities around the globe. The understanding and insight of mosquito breeding habitats features is crucial for their effective management. Comprehensive larval surveys were carried out at 14 sites in Qatar. A total of 443 aquatic habitats were examined, among these 130 were found positive with Culex pipiens, Cx. quinquefasciatus, Cx. mattinglyi, Ochlerotatus dorsalis, Oc. caspius and Anopheles stephensi. The majority of positive breeding habitats were recorded in urban areas (67.6%), followed by livestock (13.8%), and least were in agriculture (10.7%). An. stephensi larvae were positively correlated with Cx. pipien, Cx. quinquefasciatus, and negatively with water salinity. Large and shaded habitats were the most preferred by An. stephensi. In addition, Cx. pipiens was positively associated with the turbidity and pH, and was negatively associated with vegetation and habitat size. A negative association of Cx. quinquefasciatus with dissolved oxygen, water temperature, and salinity, while positive with habitat surface area was observed. Oc. dorsalis was negatively correlated with pH, water temperature, depth, and habitat surface area, whereas salinity water was more preferable site for females to lay their eggs. These results demonstrate that environmental factors play a significant role in preference of both anopheline and culicine for oviposition, while their effective management must be developed as the most viable tool to minimize mosquito borne diseases.
Membrane distillation (MD) is an attractive technology for the separation of highly saline water used with a polytetrafluoroethylene (PTFE) hollow fiber (HF) membrane. A hydrophobic coating of low-density polyethylene (LDPE) coats the outer surface of the PTFE membrane to resolve membrane wetting as well as increase membrane permeability flux and salt rejection, a critical problem regarding the MD process. LDPE concentrations in coating solution have been studied and optimized. Consequently, the LDPE layer altered membrane morphology by forming a fine nanostructure on the membrane surface that created a hydrophobic layer, a high roughness of membrane, and a uniform LDPE network. The membrane coated with different concentrations of LDPE exhibited high water contact angles of 135.14 ± 0.24 and 138.08 ± 0.01° for membranes M-3 and M-4, respectively, compared to the pristine membrane. In addition, the liquid entry pressure values of LDPE-incorporated PTFE HF membranes (M-1 to M-5) were higher than that of the uncoated membrane (M-0) with a small decrease in the percentage of porosity. The M-3 and M-4 membranes demonstrated higher flux values of 4.12 and 3.3 L m-2 h-1 at 70 °C, respectively. On the other hand, the water permeation flux of 1.95 L m-2 h-1 for M-5 further decreased when LDPE concentration is increased.
Two geometric shape turbulence promoters (circular and square of same areas) of different array patterns using three-dimensional (3D) printing technology were designed for direct contact membrane distillation (DCMD) modules in the present study. The DCMD device was performed at middle temperature operation (about 45 °C to 60 °C) of hot inlet saline water associated with a constant temperature of inlet cold stream. Attempts to reduce the disadvantageous temperature polarization effect were made inserting the 3D turbulence promoters to promote both the mass and heat transfer characteristics in improving pure water productivity. The additive manufacturing 3D turbulence promoters acting as eddy promoters could not only strengthen the membrane stability by preventing vibration but also enhance the permeate flux with lessening temperature polarization effect. Therefore, the 3D turbulence promoters were individually inserted into the flow channel of the DCMD device to create vortices in the flow stream and increase turbulent intensity. The modeling equations for predicting the permeate flux in DCMD modules by inserting the manufacturing 3D turbulence promoter were investigated theoretically and experimentally. The effects of the operating conditions under various geometric shapes and array patterns of turbulence promoters on the permeate flux with hot inlet saline temperatures and flow rates as parameters were studied. The distributions of the fluid velocities were examined using computational fluid dynamics (CFD). Experimental study has demonstrated a great potential to significantly accomplish permeate flux enhancement in such new design of the DCMD system. The permeate flux enhancement for the DCMD module by inserting 3D turbulence promoters in the flow channel could provide a maximum relative increment of up to 61.7% as compared to that in the empty channel device. The temperature polarization coefficient (τtemp) was found in this study for various geometric shapes and flow patterns. A larger τtemp value (the less thermal resistance) was achieved in the countercurrent-flow operation than that in the concurrent-flow operation. An optimal design of the module with inserting turbulence promoters was also delineated when considering both permeate flux enhancement and energy utilization effectiveness.
The 2004 Banda Aceh earthquake and ensuing Andaman mega tsunami that killed a quarter million people worldwide is a wake-up call to many. Active research was initiated in Universiti Sains Malaysia (USM) immediately after the infamous event with the aims to help develop human capacity and resources, and to mitigate any future earthquake and tsunami. The Disaster Research Nexus (DRN) was formed recently within the School of Civil Engineering, USM, to facilitate active collaborative research on earthquakes and tsunamis, as well as on other natural disasters, such as landslides. This paper begins with an introduction to DRN. This is followed by a description of some research achievements undertaken by DRN staff. A concise exposition on the tsunami simulation model TUNA developed by the authors and its application to the 2004 Andaman tsunami are given to illustrate the capability of TUNA. The role of mangrove in reducing the impact of tsunami is then modelled. Tsunami may inundate coastal plain with large quantity of saline water, changing the salinity regimes in the soil and inducing vegetative succession changes. A model called MANHAM was developed to simulate the salinity changes and its associated vegetative evolution to assist in the rehabilitation of vegetation destroyed by tsunami. Meanwhile, an earthquake risk analysis for the Upper Pandas Dam in Sabah is then presented, and this is followed by a model estimation of tsunami forces on the coastal structures. The main objective of this paper is to reach out to research scientists and onsite risk reduction professionals to collaborate towards the development of a vibrant research culture to face future natural disasters such as earthquakes and tsunamis. It is hoped that DRN will move forward to further enhance active collaborations with other research and operational institutions worldwide towards developing earthquake and tsunami resilient communities.
Aquaculture businesses in Malaysia require careful and comprehensive financial analysis to be successful. Comprehensive financial analysis has three key components, namely financial position, profitability and liquidity/cash flow. This research focuses on using pro forma income statements to analyze financial positions and to evaluate the effect of government incentives on sustainability of Malaysian aquaculture farms. This paper is divided into two sections; the first section discusses and provides the finding and comparability of the financial analysis on freshwater and brackish water producers. In the first section, the discussion was based on financial viability criteria, namely net present value (NPV), internal rate of return (IRR) and benefit cost ratio (BCR)) for base study. The evaluation process was carried out using four different phases; base study and government incentives simulations, Pioneer Status (PS), Investment Tax Allowance (ITA), and Accelerated Capital Allowance (ACA) for effectiveness of government incentives and roles in increase of profitability and production. The results showed that in all brackish water farms, NPV after the ACA incentive showed a higher and positive value comparable to individual PS and ITA. The effect of Government Incentive on Penaeus vannamei and Grouper showed that IRR and NPV on ACA (based on PS) is 2% and 9%, respectively higher than ACA (based on ITA). Meanwhile, in Barramundi farming ACA (based on ITA) was 8% higher than ACA (based on PS). The results on freshwater showed that ACA (based on ITA) on Tilapia and Catfish was 8% and 6% higher than ACA (based on PS). This paper concludes that the aquaculture operators should choose to accept PS with ACA on Penaeus vannamei and Grouper and choose ACA based on ITA on Barramundi, Tilapia and Catfish in order to maximize private profitability.