MyMedR

Displaying publications 1 - 20 of 658 in total

Abstract:

Sort:

Mechanical and microarchitectural analyses of cancellous bone through experiment and computer simulation

Syahrom A, Abdul Kadir MR, Abdullah J, Öchsner A

Med Biol Eng Comput, 2011 Dec;49(12):1393-403.
PMID: 21947767 DOI: 10.1007/s11517-011-0833-0

The relationship between microarchitecture to the failure mechanism and mechanical properties can be assessed through experimental and computational methods. In this study, both methods were utilised using bovine cadavers. Twenty four samples of cancellous bone were extracted from fresh bovine and the samples were cleaned from excessive marrow. Uniaxial compression testing was performed with displacement control. After mechanical testing, each specimen was ashed in a furnace. Four of the samples were exemplarily scanned using micro-computed tomography (μCT) and three dimensional models of the cancellous bones were reconstructed for finite element simulation. The mechanical properties and the failure modes obtained from numerical simulations were then compared to the experiments. Correlations between microarchitectural parameters to the mechanical properties and failure modes were then made. The Young's modulus correlates well with the bone volume fraction with R² = 0.615 and P value 0.013. Three different types of failure modes of cancellous bone were observed: oblique fracture (21.7%), perpendicular global fracture (47.8%), and scattered localised fracture (30.4%). However, no correlations were found between the failure modes to the morphological parameters. The percentage of error between computer predictions and the actual experimental test was from 6 to 12%. These mechanical properties and information on failure modes can be used for the development of synthetic cancellous bone.

Matched MeSH terms: Cattle
Permeability study of cancellous bone and its idealised structures

Syahrom A, Abdul Kadir MR, Harun MN, Öchsner A

Med Eng Phys, 2015 Jan;37(1):77-86.
PMID: 25523865 DOI: 10.1016/j.medengphy.2014.11.001

Artificial bone is a suitable alternative to autografts and allografts, however their use is still limited. Though there were numerous reports on their structural properties, permeability studies of artificial bones were comparably scarce. This study focused on the development of idealised, structured models of artificial cancellous bone and compared their permeability values with bone surface area and porosity. Cancellous bones from fresh bovine femur were extracted and cleaned following an established protocol. The samples were scanned using micro-computed tomography (μCT) and three-dimensional models of the cancellous bones were reconstructed for morphology study. Seven idealised and structured cancellous bone models were then developed and fabricated via rapid prototyping technique. A test-rig was developed and permeability tests were performed on the artificial and real cancellous bones. The results showed a linear correlation between the permeability and the porosity as well as the bone surface area. The plate-like idealised structure showed a similar value of permeability to the real cancellous bones.

Matched MeSH terms: Cattle
Seasonal prevalence of bovine trypanosomosis in a tsetse-infested zone and a tsetse-free zone of the Amhara Region, north-west Ethiopia

Cherenet T, Sani RA, Panandam JM, Nadzr S, Speybroeck N, van den Bossche P

Onderstepoort J Vet Res, 2004 Dec;71(4):307-12.
PMID: 15732457

During a period of four consecutive years, trypanosomosis surveys were conducted in a tsetse-infested and tsetse-free area of the Amhara Region of north-west Ethiopia. In each study area randomly selected communal cattle were sampled and their blood was investigated using parasitological diagnostic methods. At the same time the population of biting flies was sampled. The monthly average prevalence of trypanosome infections in cattle did not differ significantly between study areas. In both study areas, the prevalence of trypanosome infections was highest during the long rainy season. Trypanosome infections were mainly due to Trypanosoma vivax and they significantly reduced the average packed cell volume and the body condition of the animals. The monthly prevalence of infection was correlated with the density of biting flies, such as Tabanidae and Stomoxys spp., in the preceding month suggesting an important role of mechanical transmission in the epidemiology of trypanosomosis in both areas.

Matched MeSH terms: Cattle
Fulltext Epidemiology of foot-and-mouth disease outbreaks in Thailand from 2011 to 2018

Chanchaidechachai T, Saatkamp H, de Jong M, Inchaisri C, Hogeveen H, Premashthira S, et al.

Transbound Emerg Dis, 2022 Nov;69(6):3823-3836.
PMID: 36321258 DOI: 10.1111/tbed.14754

Foot-and-mouth disease (FMD) is one of the most important animal diseases hindering livestock production in Thailand. In this study, a temporal and spatial analysis at the subdistrict level was performed on FMD outbreak reports in Thailand from 2011 to 2018. Risk factors associated with FMD outbreaks were furthermore investigated using generalized estimating equations. The results showed that the incidence of FMD outbreaks was the highest in 2016 and was affected by season, with a peak in FMD outbreaks occurring in the rainy-winter season, during October to December. FMD outbreaks were mostly distributed in small clusters within a few subdistricts. Some high-risk areas with repeated outbreaks were detected in the central regions. Risk factors, including the increase of subdistrict's size of the dairy population, beef population or pig population, the low percentage of forest area, subdistricts in the provinces adjacent to Malaysia, the presence of a livestock market and the occurrence of an FMD outbreak in a neighbouring subdistrict in the previous month significantly increased the odds of having an FMD outbreak. The increase in proximity to the nearest subdistrict with an FMD outbreak in the previous month decreased the odds of having FMD outbreaks. This study helped to identify high-risk areas and periods of FMD outbreaks in Thailand. Together with the identified risk factors, its results can be used to optimize the FMD control programme in Thailand and in other countries having a similar livestock industry and FMD situation.

Matched MeSH terms: Cattle
Validation of ELISA test kits for detection of beta-agonist residues in meat

Ponniah J, Muhammad K, Abdullah S, Ganapathy KK, bt Sheikh Abdul Hamid N

Southeast Asian J. Trop. Med. Public Health, 2004 Jun;35(2):481-7.
PMID: 15691160

Three ELISA test kits, the Randox ELISA beta-agonist test kit, Euro-Diagnostica test kit, and Ridascreen beta-agonist test kit, were evaluated for screening of meat and liver for beta-agonist residues in fortified and field-incurred samples. It was found that the Randox beta-agonist test kit was more suitable as a screening tool due to its accuracy, ease of use, and lower cost. The tests were able to detect beta-agonist residues at the minimum level of detection, as claimed by the suppliers. The performance of the method as assessed through recovery rates of beta-agonists in fortified samples was satisfactory with a low coefficient of variation (1-3%). Repeatability, as measured through the coefficient of correlation was also satisfactory. For field-incurred positive samples, the test kit showed a sensitivity of 100% and a low rate of false positives for goat and cow tissues. However, a high rate of apparent false positives was obtained for tissues of swine.

Matched MeSH terms: Cattle
Comparative clinicopathological changes in buffalo and cattle following infection by Pasteurella multocida B:2

Annas S, Zamri-Saad M, Jesse FF, Zunita Z

Microb Pathog, 2015 Nov;88:94-102.
PMID: 26298001 DOI: 10.1016/j.micpath.2015.08.009

Haemorrhagic septicaemia (HS) is an acute, septicaemic disease of cattle and buffalo of Asia and Africa caused by Pasteurella multocida B:2 or E:2. Buffaloes are believed to be more susceptible than cattle. In this study, 9 buffaloes of 8 months old were divided equally into 3 groups (Groups 1, 3, 5). Similarly, 9 cattle of 8 months old were equally divided into 3 groups (Groups 2, 4, 6). Animals of Groups 1 and 2 were inoculated with PBS while Groups 3 and 4 were inoculated subcutaneously with 10(5) cfu/ml of P. multocida B:2. Animals of Groups 5 and 6 were inoculated intranasally with the same inoculum. Both buffaloes and cattle that were inoculated subcutaneously succumbed to the infection at 16 h and 18 h, respectively. Two buffaloes that were inoculated intranasally (Group 5) succumbed at 68 h while the remaining cattle and buffaloes survived the 72-h study period. Endotoxin was detected in the blood of infected cattle (Group 4) and buffaloes (Groups 3 and 5) prior to the detection of P. multocida B:2 in the blood. The endotoxin was detected in the blood of buffaloes of Group 3 and cattle of Group 4 at 0.5 h post-inoculation while buffaloes of Group 5 and cattle of Group 6 at 1.5 h. On the other hand, bacteraemia was detected at 2.5 h in buffaloes of Group 3 and cattle of Group 4 and at 12 h in buffaloes of Group 5 and cattle of Group 6. Affected cattle and buffaloes showed lesions typical of haemorrhagic septicaemia. These included congestion and haemorrhages in the organs of respiratory, gastrointestinal and urinary tracts with evidence of acute inflammatory reactions. The severity of gross and histopathology lesions in cattle and buffalo calves that succumbed to the infection showed insignificant (p > 0.05) difference. However, inoculated buffalo and cattle that survived the infection showed significantly (p < 0.05) less severe gross and histopathological changes than those that succumbed. In general, cattle are more resistant to intranasal infection by P. multocida B:2 than buffaloes.

Matched MeSH terms: Cattle
Chromosomes of gaur cross domestic cattle hybrids

Bongso TA, Hilmi M, Sopian M, Zulkifli S

Res Vet Sci, 1988 Mar;44(2):251-4.
PMID: 3387680

The chromosomes of five gaur (Bos gaurus hubbacki) domestic cattle (B indicus cross B taurus) hybrids (three females, two males) were studied using the leucocyte culture method and centromeric (C) banding technique. All the hybrids had a diploid chromosome number of 2n = 58, made up of two submetacentric autosomes (different in size) and 54 acrocentric autosomes, most of which could be arranged in pairs in descending order of size. The sex (X) chromosomes in females were a pair of submetacentric chromosomes smaller than the submetacentric autosomes. The Y chromosome in males was a small submetacentric chromosome. The C banding patterns were useful in identifying the X and Y chromosomes and the inherited submetacentric autosomes from the gaur sire. Phenotypically, the hybrids resembled normal B indicus cross B taurus calves except for the presence of a distinct hump-like dorsal ridge containing the spinous processes of the third to 11th thoracic vertebrae, upright 'deer-like' ears and long lean legs. The potential of these hybrids as important genetic resources for meat production is stressed.

Matched MeSH terms: Cattle/genetics*
Fulltext Light microscopy and molecular identification of Sarcocystis spp. in meat producing animals in Selangor, Malaysia

Latif B, Kannan Kutty M, Muslim A, Hussaini J, Omar E, Heo CC, et al.

Trop Biomed, 2015 Sep;32(3):444-52.
PMID: 26695204 MyJurnal

One thousand and forty-five tissue samples of skeletal muscles, tongue, heart, diaphragm and esophagus were collected from 209 animals (43 sheep, 89 goats and 77 cattle) from an abattoir in Selangor between February and October, 2013. Each sample was divided into three pieces with each piece measuring 2-3 mm3. Each piece was then squeezed between two glass slides and examined microscopically at x 10 magnification for the presence of sarcocystosis. Three positive samples from each animal species were then fixed in 10% formalin for histological processing. Seven positive samples collected from each animal species were preserved at -80°C or 90% ethanol for gene expression studies. Microsarcocysts were detected in 114 (54.5%) animals by light microscopy (LM). The infection rates in sheep, goat and cattle were 86, 61.8 and 28.6% respectively. The highest rate of infection was in the skeletal muscles of sheep (64.9%) and goats (63.6%) and in the heart of cattle (63.6%). The cysts were spindle to oval in shape and two stages were recognized, the peripheral metrocytes and centrally located banana-shaped bradyzoites. 18S rRNA gene expression studies confirmed the isolates from the sheep as S. ovicanis, goats as S. capracanis and cattle as S. bovicanis. This, to the best of our knowledge, is the first molecular identification of an isolate of S. ovicanis and S. capracanis in Malaysia. Further studies with electron microscopy (EM) are required in the future to compare the features of different types of Sarcocysts spp.

Matched MeSH terms: Cattle; Cattle Diseases/diagnosis*; Cattle Diseases/parasitology
Fulltext Seroprevalence of Toxoplasma gondii antibodies in pigs, goats, cattle, dogs and cats in peninsular Malaysia

Chandrawathani P, Nurulaini R, Zanin CM, Premaalatha B, Adnan M, Jamnah O, et al.

Trop Biomed, 2008 Dec;25(3):257-8.
PMID: 19287367

Antibodies to the protozoan parasite, Toxoplasma gondii were assayed in sera of 200 goats, 100 pigs, 126 cattle from various states of Malaysia, and 135 dogs and 55 cats around Ipoh region using an indirect fluorescence antibody test (IFAT, cut-off titer 1:200); antibodies were found in 35.5% of goats, 14.5% cats, 9.6% dogs, 7.9% local cattle and 4% yellow cattle but not in pigs. Results indicate that infection is most prevalent in goats.

Matched MeSH terms: Cattle/parasitology*
Fulltext Shear bond strength of orthodontic adhesives on different tooth types : an in vitro study

Radzi, Z., Yahya, N.A., Kasim, N.H.A., Ismail, N.H., Ismail, N.A., Zamzam, N

Ann Dent, 2006;13(1):18-23.
MyJurnal

Introduction: Owing to the variety of materials and methods employed, comparison of the results and findings from bonding studies is difficult. Until recently, several types of teeth have been used in published research papers as a substrate in orthodontic bonding research including bovine incisors, fresh and rebonded human premolars. Objectives: The purpose of this study was to compare the shear bond strength of an adhesive bonded to different tooth surfaces (human premolar, bovine incisor and rebonded human premolar). Methods: Two groups of thirty premolar teeth and one group of bovine incisors had brackets attached in a standardized manner using Transbond XT (3M Unitek). The adhesive was cured using conventional halogen light and a specially designed tool to standardize the distance between the light curing tip and the adhesive. The debonding force was measured using Instron universal testing machine. ANOVA and Post Hoc Dunnett C test were performed to determine any significant difference among groups (p

Matched MeSH terms: Cattle
In-vitro phagocytosis and intracellular killing of Pasteurella multocida B:2 by phagocytic cells of buffaloes

Puspitasari Y, Annas S, Adza-Rina MN, Zamri-Saad M

Microb Pathog, 2019 Jun;131:170-174.
PMID: 30978429 DOI: 10.1016/j.micpath.2019.04.012

Pasteurella multocida B:2 is a Gram-negative organism causing haemorrhagic septicaemia (HS) in buffaloes. It causes severe pulmonary infection, leading to infiltration of numerous macrophages and neutrophils. Despite the inflammatory response, buffaloes succumb to HS. This study aims to evaluate the in-vitro efficacy of macrophages and neutrophils of buffalo following exposure to P. multocida B:2. In-vitro infections were done using 107 cfu/ml of P. multocida B:2 for Group 1, Escherichia coli for Group 2 and Mannhaemia haemolytica A:2 for Group 3 cells. The inoculated cell cultures were harvested at 0, 30, 60 and 120 min post-exposure and the phagocytic, killing and cell death rates were determined. Both phagocytosis and killing rates of all bacteria increased over time. Phagocytosis involved between 71% and 73% neutrophils and between 60% and 64% macrophages at 120 min. Killing rate of all bacteria involved between 76% and 79% for neutrophils and between 70% and 74% for macrophages at 120 min. Death rate of neutrophils ranged between 67% in Group 3, and 88% in Group 1 at 120 min, significantly (p  0.05) than Group 2. Similar pattern was observed for death rate of macrophages. The phagocytosis and killing rates of P. multocida B:2 were similar to other bacterial species used in this study but more neutrophils and macrophages were dead following infection by P. multocida B:2 than M. haemolytica A:2.

Matched MeSH terms: Cattle; Cattle Diseases/immunology*; Cattle Diseases/microbiology
Fulltext Multiplex Polymerase Chain Reaction (PCR) efficiency in detection of pathogenic Escherichia coli O157:H7

Suria, M. S., Adlin Azlina, A. K., Mohd Afendy, A. T., Zamri, I.

International Food Research Journal, 2013;20(6):3307-3311.
MyJurnal

Shiga toxin-producing E. coli (STEC) is an important foodborne pathogen causing diarrhea, hemorrhagic colitis and hemolytic-uremic syndrome in humans. STEC is an implicated in the vast majority of outbreaks, widely via consumption of STEC contaminated beef, as important vehicle of transmission of this organism to human. The E. coli O157:H7 serotype is traditionally identified by serological identification of the somatic antigen (O157) and structural flagella (H7). In this study, the bacteria were identified as STEC serotype O157:H7 with three primer pairs that amplified fragments of secD, rfbE and fliC genes in PCR assays. These primer pairs specifically amplified different sizes of target genes: a 244bp region of the E. coli diagnostic marker gene (secD); a 317bp region of the O157 lipopolysacharide (LPS) gene (rfbE); and a 381bp region of the H7 flagellin gene (fliC). The singleplex, duplex and triplex PCR assay developed in this study have a sensitivity limit at 2.8 x 103, 2.8 x 105 and 2.8 x 107 CFU/ml of E. coli O157:H7, respectively. Sensitivity to detect trace amount of E. coli O157:H7 DNA was reduced as the number of primer used was increased for competing to the same DNA template.

Matched MeSH terms: Cattle
Fulltext Antiplasmodial properties of some Malaysian medicinal plants

Noor Rain A, Khozirah S, Mohd Ridzuan MA, Ong BK, Rohaya C, Rosilawati M, et al.

Trop Biomed, 2007 Jun;24(1):29-35.
PMID: 17568375 MyJurnal

Seven Malaysian medicinal plants were screened for their antiplasmodial activities in vitro. These plants were selected based on their traditional claims for treatment or to relieve fever. The plant extracts were obtained from Forest Research Institute Malaysia (FRIM). The antiplasmodial activities were carried out using the pLDH assay to Plasmodium falciparum D10 strain (sensitive strain) while the cytotoxic activities were carried out towards Madin- Darby bovine kidney (MDBK) cells using MTT assay. The concentration of extracts used for both screening assays were from the highest concentration 64 microg/ml, two fold dilution to the lowest concentration 0.03 microg/ml. Goniothalamus macrophyllus (stem extract) showed more than 60% growth inhibition while Goniothalamus scortechinii root and stem extract showed a 90% and more than 80% growth inhibition at the last concentration tested, 0.03 microg/ml. The G. scortechini (leaves extract) showed an IC50 (50% growth inhibition) at 8.53 microg/ml, Ardisia crispa (leaves extract) demonstrated an IC50 at 5.90 +/- 0.14 microg/ml while Croton argyratus (leaves extract) showed a percentage inhibition of more than 60% at the tested concentration. Blumea balsamifera root and stem showed an IC50 at 26.25 +/- 2.47 microg/ml and 7.75 +/- 0.35 microg/ ml respectively. Agathis borneensis (leaves extract) demonstrated a 50% growth inhibition at 11.00 +/- 1.41 microg/ml. The study gives preliminary scientific evidence of these plant extracts in line with their traditional claims.

Matched MeSH terms: Cattle
Fulltext Bovine brucellosis trends in Malaysia between 2000 and 2008

Anka MS, Hassan L, Adzhar A, Khairani-Bejo S, Mohamad RB, Zainal MA

BMC Vet Res, 2013;9:230.
PMID: 24246015 DOI: 10.1186/1746-6148-9-230

Bovine brucellosis is an important disease affecting cattle characterised by abortion, still birth, reduced milk production, weak foetus and infertility in both males and females. There is wide distribution of the disease among cattle and several wildlife species. Bovine brucellosis is commonly caused by B. abortus and very occasionally B. melitensis and B. suis. The distribution of bovine brucellosis in cattle has not been described in Malaysia. In this paper we describe the distribution, pattern and trend of bovine brucellosis in Peninsular Malaysia between 2000 and 2008 based on serological data obtained from nationwide B. abortus serosurveillance activities in cattle populations.

Matched MeSH terms: Cattle
Chemical and Chemometric Methods for Halal Authentication of Gelatin: An Overview

Hassan N, Ahmad T, Zain NM

J Food Sci, 2018 Dec;83(12):2903-2911.
PMID: 30440088 DOI: 10.1111/1750-3841.14370

The issue of food authenticity has become a concern among religious adherents, particularly Muslims, due to the possible presence of nonhalal ingredients in foods as well as other commercial products. One of the nonhalal ingredients that commonly found in food and pharmaceutical products is gelatin which extracted from porcine source. Bovine and fish gelatin are also becoming the main commercial sources of gelatin. However, unclear information and labeling regarding the actual sources of gelatin in food and pharmaceutical products have become the main concern in halal authenticity issue since porcine consumption is prohibited for Muslims. Hence, numerous analytical methods involving chemical and chemometric analysis have been developed to identify the sources of gelatin. Chemical analysis techniques such as biochemical, chromatography, electrophoretic, and spectroscopic are usually combined with chemometric and mathematical methods such as principal component analysis, cluster, discriminant, and Fourier transform analysis for the gelatin classification. A sample result from Fourier transform infrared spectroscopy analysis, which combines Fourier transform and spectroscopic technique, is included in this paper. This paper presents an overview of chemical and chemometric methods involved in identification of different types of gelatin, which is important for halal authentication purposes.

Matched MeSH terms: Cattle
Double Gene Targeting Multiplex Polymerase Chain Reaction-Restriction Fragment Length Polymorphism Assay Discriminates Beef, Buffalo, and Pork Substitution in Frankfurter Products

Hossain MA, Ali ME, Abd Hamid SB, Asing, Mustafa S, Mohd Desa MN, et al.

J Agric Food Chem, 2016 Aug 17;64(32):6343-54.
PMID: 27501408 DOI: 10.1021/acs.jafc.6b02224

Beef, buffalo, and pork adulteration in the food chain is an emerging and sensitive issue. Current molecular techniques to authenticate these species depend on polymerase chain reaction (PCR) assays involving long and single targets which break down under natural decomposition and/or processing treatments. This novel multiplex polymerase chain reaction-restriction fragment length polymorphism assay targeted two different gene sites for each of the bovine, buffalo, and porcine materials. This authentication ensured better security, first through a complementation approach because it is highly unlikely that both sites will be missing under compromised states, and second through molecular fingerprints. Mitochondrial cytochrome b and ND5 genes were targeted, and all targets (73, 90, 106, 120, 138, and 146 bp) were stable under extreme boiling and autoclaving treatments. Target specificity and authenticity were ensured through cross-amplification reaction and restriction digestion of PCR products with AluI, EciI, FatI, and CviKI-1 enzymes. A survey of Malaysian frankfurter products revealed rampant substitution of beef with buffalo but purity in porcine materials.

Matched MeSH terms: Cattle/genetics*
Fulltext Work Environment-Related Risk Factors for Leptospirosis among Plantation Workers in Tropical Countries: Evidence from Malaysia

Mohd Ridzuan J, Aziah BD, Zahiruddin WM

Int J Occup Environ Med, 2016 07;7(3):156-63.
PMID: 27393322 DOI: 10.15171/ijoem.2016.699

BACKGROUND: Leptospirosis is a zoonotic disease that is recognized as a re-emerging global public health issue, especially in tropical and subtropical countries. Malaysia, for example, has increasingly registered leptospirosis cases, outbreaks, and fatalities over the past decade. One of the major industries in the country is the palm oil sector, which employs numerous agricultural workers. These laborers are at a particularly high risk of contracting the disease.
OBJECTIVE: To identify the work environment-related risk factors for leptospirosis infection among oil palm plantation workers in Malaysia.
METHODS: A cross-sectional study involving 350 workers was conducted. The participants were interviewed and administered a microscopic agglutination test. Seropositivity was determined using a cut-off titer of ≥1:100.
RESULTS: 100 of 350 workers tested positive for leptospiral antibodies, hence, a seroprevalence of 28.6% (95% CI 23.8% to 33.3%). The workplace environment-related risk factors significantly associated with seropositive leptospirosis were the presence of cows in plantations (adjusted OR 4.78, 95% CI 2.76 to 8.26) and the presence of a landfill in plantations (adjusted OR 2.04, 95% CI 1.22 to 3.40).
CONCLUSION: Preventing leptospirosis incidence among oil palm plantation workers necessitates changes in policy on work environments. Identifying modifiable factors may also contribute to the reduction of the infection.

Matched MeSH terms: Cattle
Fulltext Effects of marbling on physical and sensory characteristics of ribeye steaks from four different cattle breeds

Shahrai NN, Babji AS, Maskat MY, Razali AF, Yusop SM

Anim Biosci, 2021 May;34(5):904-913.
PMID: 32810938 DOI: 10.5713/ajas.20.0201

OBJECTIVE: Marbling or intramuscular fat (IMF) has been widely reported to directly impact the sensory acceptance of meat. This study was carried out to determine the physical and sensory characteristics of ribeye, Longissimus dorsi steaks obtained from four different cattle breeds namely Wagyu, Angus, Brahman, and Malaysian local beef, the Kedah-Kelantan (KK).
METHODS: The degree of marbling was determined by using an established combined camera-image analysis technique while instrumental texture determination was carried out by using Warner-Bratzler shear force analysis. Sensory evaluation of the beef steaks was performed following a quantitative descriptive analysis incorporating 10 trained consumer panelists.
RESULTS: Wagyu was found to possess the highest (p<0.05) percentage of IMF at 33.90% and the lowest shear force (raw = 5.61 N/mm2; cooked = 14.72 N/mm2) followed by Angus (20.87%), Brahman (12.17%), and KK (p<0.05, 6.86%). The difference in sensory properties of the four steaks was evident, with Wagyu appearing to be highly correlated with most sensory attributes measured namely sustained buttery, tooth-packing, chewiness, juiciness, tenderness, mouthfeel, oiliness, and overall acceptability. The Malaysian local beef, KK was found to be less acceptable (p<0.05), although most of its sensory attributes were found similar (p>0.05) in appearance, aroma, texture, juiciness, and flavour to the cooked steak from Angus and Brahman.
CONCLUSION: This present study demonstrated the role of IMF in determining the quality and sensory acceptance of beef from different cattle breeds. These data have provided new information and further understanding on the physical and sensory quality of Malaysian local beef.

Matched MeSH terms: Cattle
Molecular characterization and phylogeny of Shiga toxin-producing E. coli (STEC) from imported beef meat in Malaysia

Abuelhassan NN, Mutalib SA, Gimba FI, Yusoff WM

Environ Sci Pollut Res Int, 2016 Sep;23(17):17553-62.
PMID: 27234829 DOI: 10.1007/s11356-016-6954-0

This study aimed at determining the presence and characterization of Escherichia coli and Shiga toxin-producing E. coli (STEC) from imported frozen beef meats. Seventy-four (74) frozen imported beef meat samples from two countries, India (42 samples) and Australia (32 samples), were collected and tested for E. coli. These samples were purchased from the frozen meat sections of five different supermarkets in different locations in Selangor, Malaysia, from April 2012 to October 2014. A total of 222 E. coli strains were isolated from the meat samples; 126 strains were isolated from country A (India), and 96 E. coli strains were from country of origin B (Australia), respectively. A total of 70 E. coli strains were identified and characterized. All E. coli strains were isolated into Fluorocult medium and identified using API 20E kit. All selected E. coli strains were characterized for Shiga toxin genes (stx1 and stx2). All biochemically identified E. coli in this study were further subjected to molecular detection through polymerase chain reaction (PCR) amplification and characterization using 16S ribosomal RNA (rRNA) gene of Shiga toxin-producing E. coli. Of the 70 E. coli strains, 11 strains were positive for both Shiga toxin genes (stx1 and stx2) and 11 (11/70) strains were positive for stx1 gene, while 25 (25/70) strains were positive for stx2 gene. The analysis of 16S rRNA gene of all the E. coli isolates in this study was successfully sequenced and analyzed, and based on sequence data obtained, a phylogenetic tree of the 16S rRNA gene was performed using Clustal W programme in MEGA 6.06 software. Phylogenetic tree showed that the E. coli isolates in our study cluster with the strain of E. coli isolated in other countries, which further confirm that the isolates of E. coli in this study are similar to those obtained in other studies. As a result, all the strains obtained in this study proved to be a strain of pathogenic E. coli, which may cause a serious outbreak of food-borne disease. The isolation of pathogenic E. coli strains from the imported meat samples calls for prudent management of imported meats by the relevant authorities.

Matched MeSH terms: Cattle
Development of chitosan edible film incorporated with Chrysanthemum morifolium essential oil

Tan LF, Elaine E, Pui LP, Nyam KL, Yusof YA

Acta Sci Pol Technol Aliment, 2021 1 16;20(1):55-66.
PMID: 33449520 DOI: 10.17306/J.AFS.0771

BACKGROUND: Biodegradable food packaging has improved in quality with recent research incorporating natural extracts for functionality purposes. This research aims to develop chitosan film with Chrysanthemum morifolium essential oil to improve the shelf life of fresh raw chicken and beef.
METHODS: 1.5% (w/v) chitosan films with Chrysanthemum morifolium essential oil (0% to 6% (v/v)) were produced through homogenization, the casting of a film solution in a petri dish and convection drying. The edible film was evaluated in terms of its physical (color, thickness, water vapor permeability), mechanical (puncture strength, tensile strength, elongation at break) and chemical properties (antioxidant assay, Fourier Transform Infrared Spectroscopy (FTIR)).
RESULTS: With an increasing concentration of Chrysanthemum morifolium in the chitosan film, the test values of physical properties such as tensile strength, puncture force, and elongation at break declined significantly. However, the thickness, water permeability, and color profile (L*, a*, b*) values of the chitosan film increased. Similarly, the scavenging effect of antioxidant assay increased (from 4.97% to 18.63%) with a rise in Chrysanthemum morifolium concentration. 2%, 3%, and 4% of Chrysanthemum morifolium in the chitosan film showed a significant inhibition zone ranging from 2.67 mm to 3.82 mm against Staphylococcus aureus, a spoilage bacterium that is commonly found in chicken and beef products. The storage and pH tests showed that 4% of Chrysanthemum morifolium in the film maintained pH level (safe to consume), and the shelf life was extended from 3 days to 5 days of meat storage.
CONCLUSIONS: This study demonstrated that the incorporation of 4% (v/v) Chrysanthemum morifolium extract into 1.5% (w/v) chitosan film extends the storage duration of raw meat products noticeably by reducing Staphylococcus aureus activity. Therefore, it increases the quality of the edible film as an environmentally friendly food packaging material so that it can act as a substitute for the use of plastic bags. Future studies will be conducted on improving the tensile strength of the edible film to increase the feasibility of using it in the food industry. In addition, the microstructure and surface morphology of the edible film can be further determined.

Matched MeSH terms: Cattle

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links